LTC3788-1 2-Phase, Dual Output Synchronous Boost Controller DESCRIPTION FEATURES n n n n n n n n n n n n n n The LTC®3788-1 is a high performance 2-phase dual synchronous boost converter controller that drives all N-channel power MOSFETs. Synchronous rectification increases efficiency, reduces power losses and eases thermal requirements, allowing the LTC3788-1 to be used in high power boost applications. Synchronous Operation for Highest Efficiency and Reduced Heat Dissipation Wide Input Range: 4.5V to 38V (40V Abs Max) and Operates Down to 2.5V After Start-Up Output Voltages Up to 60V ±1% 1.2V Reference Voltage RSENSE or Inductor DCR Current Sensing 100% Duty Cycle Capability for Synchronous MOSFET Low Quiescent Current: 125μA Phase-Lockable Frequency (75kHz to 850kHz) Programmable Fixed Frequency (50kHz to 900kHz) Adjustable Output Voltage Soft-Start Power Good Output Voltage Monitor Low Shutdown Current IQ: < 8μA Internal LDO Powers Gate Drive from VBIAS or EXTVCC Available in a Narrow SSOP Package A constant-frequency current mode architecture allows a phase-lockable frequency of up to 850kHz. OPTI-LOOP compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The LTC3788-1 features a precision 1.2V reference and a power good output indicator. A 4.5V to 38V input supply range encompasses a wide range of system architectures and battery chemistries. Independent SS pins for each controller ramp the output voltages during start-up. The PLLIN/MODE pin selects among Burst Mode operation, pulse-skipping mode or continuous inductor current mode at light loads. APPLICATIONS n n n Industrial Automotive Medical Military For a leadless 32-pin QFN package with additional features of adjustable current limit, clock out, phase modulation and two PGOOD outputs, see the LTC3788 data sheet. L, LT, LTC, LTM, Linear Technology, OPTI-LOOP, Burst Mode and the Linear logo are registered trademarks and No RSENSE and ThinSOT are trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U. S. Patents, including 5408150, 5481178, 5705919, 5929620, 6144194, 6177787, 6580258. TYPICAL APPLICATION VIN 4.5V TO 12V START-UP VOLTAGE OPERATES THROUGH TRANSIENTS DOWN TO 2.5V VIN 4.7μF 4.7μF 3mΩ TG1 VBIAS INTVCC 1.25μH VOUT 12V AT 5A BOOST1 BOOST2 3.3μH VOUT 24V AT 3A 0.1μF BG2 + SENSE2+ SENSE1– SENSE2– SENSE1 90 SW2 LTC3788-1 PGND 2.7k 15nF 220pF 0.1μF 50 10 40 10 15nF 12.1k 100 60 VIN = 12V 1 VOUT = 24V Burst Mode OPERATION FIGURE 9 CIRCUIT 0.1 0 0.00001 0.0001 0.001 0.01 0.1 1 10 OUTPUT CURRENT (A) VFB2 FREQ PLLIN/MODE ITH1 SS1 SGND SS2 ITH2 100pF 0.1μF 70 20 232k 220μF 1000 80 30 110k VFB1 10000 100 POWER LOSS (mW) BG1 220μF 4mΩ TG2 0.1μF SW1 Efficiency and Power Loss vs Load Current EFFICIENCY (%) n 8.66k 220μF 37881 TA01b 12.1k 37881 TA01a 37881fa 1 LTC3788-1 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Notes 1, 3) VBIAS......................................................... –0.3V to 40V BOOST1, BOOST2 ...................................... –0.3V to 76V SW1, SW2 ................................................. –0.3V to 70V RUN1, RUN2 ................................................ –0.3V to 8V Maximum Current Sourced into Pin from Source > 8V..............................................100μA PGOOD1, PLLIN/MODE ............................... –0.3V to 6V INTVCC, (BOOST1-SW1, BOOST2-SW2) ...... –0.3V to 6V EXTVCC ......................................................... –0.3V to 6V SENSE1+, SENSE1–, SENSE2+, SENSE2–.................................... –0.3V to 40V SENSE1+ – SENSE1–, SENSE2+ – SENSE2– ................................. –0.3V to 0.3V SS1, SS2, ITH1, ITH2, FREQ, VFB1, VFB2 ........................................... –0.3V to INTVCC Operating Junction Temperature Range ... –40°C to 125°C Storage Temperature Range................... –65°C to 125°C Lead Temperature (Soldering, 10 seconds) .......... 300°C TOP VIEW ITH1 1 28 SS1 VFB1 2 27 PGOOD1 SENSE1+ 3 26 SW1 SENSE1– 4 25 TG1 FREQ 5 24 BOOST1 PLLIN/MODE 6 23 BG1 SGND 7 22 VBIAS RUN1 8 21 PGND RUN2 9 20 EXTVCC SENSE2– 10 19 INTVCC SENSE2+ 18 BG2 11 VFB2 12 17 BOOST2 ITH2 13 16 TG2 SS2 14 15 SW2 GN PACKAGE 28-LEAD PLASTIC SSOP TJMAX = 125°C, θJA = 80°C/W ORDER INFORMATION LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC3788EGN-1#PBF LTC3788EGN-1#TRPBF LTC3788GN-1 28-Lead Plastic SSOP –40°C to 125°C LTC3788IGN-1#PBF LTC3788IGN-1#TRPBF LTC3788GN-1 28-Lead Plastic SSOP –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25°C, VBIAS = 12V, unless otherwise noted (Note 2). SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Main Control Loop VBIAS Chip Bias Voltage Operating Range 4.5 VFB1,2 Regulated Feedback Voltage ITH = 1.2V (Note 4) IFB1,2 Feedback Current (Note 4) VREFLNREG Reference Line Voltage Regulation VIN = 6V to 38V l 1.188 1.200 38 V 1.212 V ±5 ±50 nA 0.002 0.02 %/V 37881fa 2 LTC3788-1 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25°C, VBIAS = 12V, unless otherwise noted (Note 2). SYMBOL PARAMETER CONDITIONS VLOADREG Output Voltage Load Regulation (Note 4) TYP MAX UNITS Measured in Servo Loop; ΔITH Voltage = 1.2V to 0.7V l 0.01 0.1 % Measured in Servo Loop; ΔITH Voltage = 1.2V to 2V l –0.01 –0.1 % gm1,2 Error Amplifier Transconductance ITH = 1.2V IQ Input DC Supply Current (Note 5) UVLO MIN 2 mmho Pulse-Skipping or Forced Continuous Mode RUN1 = 5V and RUN2 = 0V or RUN1 = 0V (One Channel On) and RUN2 = 5V; VFB1(2) = 1.25V (No Load) 0.9 mA Pulse-Skipping or Forced Continuous Mode RUN1,2 = 5V; VFB1,2 = 1.25V (No Load) (Both Channels On) 1.2 mA Sleep Mode (One Channel On) RUN1 = 5V and RUN2 = 0V or RUN1 = 0V and RUN2 = 5V; VFB1(2) = 1.25V (No Load) 125 190 μA Sleep Mode (Both Channels On) RUN1,2 = 5V; VFB1,2 = 1.25V (No Load) 200 300 μA Shutdown RUN1,2 = 0V 8 20 μA INTVCC Undervoltage Lockout Thresholds VINTVCC Ramping Up l 4.1 4.3 V VINTVCC Ramping Down l 3.6 3.8 VRUN Rising l 1.18 1.28 VRUN1,2 RUN Pin On Threshold V 1.38 V VRUNHYS RUN Pin Hysteresis 100 mV IRUN1,2 RUN Pin Hysteresis Current VRUN > 1.28V 4.5 μA IRUN1,2 RUN Pin Current VRUN < 1.28V 0.5 μA ISS1,2 Soft-Start Charge Current VSS = GND 10 μA VSENSE(MAX) Maximum Current Sense Threshold VFB = 1.1V VSENSE(CM) SENSE Pins Common Mode Range (BOOST Converter Input Supply Voltage VIN) ISENSE1,2+ SENSE+ Pin Current VFB = 1.1V ISENSE1,2– SENSE– Pin Current VFB = 1.1V t r(TG1,2) Top Gate Rise Time CLOAD = 3300pF (Note 6) 20 ns t f(TG1,2) Top Gate Fall Time CLOAD = 3300pF (Note 6) 20 ns t r(BG1,2) Bottom Gate Rise Time CLOAD = 3300pF (Note 6) 20 ns t f(BG1,2) Bottom Gate Fall Time CLOAD = 3300pF (Note 6) 20 ns RUP(TG1,2) Top Gate Pull-Up Resistance 1.2 Ω RDN(TG1,2) Top Gate Pull-Down Resistance 1.2 Ω RUP(TG1,2) Bottom Gate Pull-Up Resistance 1.2 Ω RDN(TG1,2) Bottom Gate Pull-Down Resistance 1.2 Ω t D(TG/BG) Top Gate Off to Bottom Gate On Switch-On Delay Time CLOAD = 3300pF (Each Driver) 70 ns t D(BG/TG) Bottom Gate Off to Top Gate On Switch-On Delay Time CLOAD = 3300pF (Each Driver) 70 ns DFMAX(BG1,2) Maximum BG Duty Factor 96 % tON(MIN) Minimum BG On-Time 110 ns l 68 75 2.5 (Note 7) 200 82 mV 38 V 300 μA ±1 μA 37881fa 3 LTC3788-1 ELECTRICAL CHARACTERISTICS The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25°C, VBIAS = 12V, unless otherwise noted (Note 2). SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS 6V < VBIAS < 38V, VEXTVCC = 0V 5.2 5.4 5.6 V 0.5 2 % 5.4 5.6 V 0.5 2 % 4.8 5 V INTVCC Linear Regulator VINTVCCVIN Internal VCC Voltage VLDOVIN INTVCC Load Regulation ICC = 0mA to 50mA, VEXTVCC = 0V VINTVCCEXT Internal VCC Voltage VEXTVCC = 6V VLDOEXT INTVCC Load Regulation ICC = 0mA to 40mA, VEXTVCC = 6V VEXTVCC EXTVCC Switchover Voltage EXTVCC Ramping Positive VLDOHYS EXTVCC Hysteresis 5.2 4.5 250 mV 105 kHz Oscillator and Phase-Locked Loop fPROG Programmable Frequency RFREQ = 25k RFREQ = 60k 335 RFREQ = 100k 400 465 760 fLOW Lowest Fixed Frequency VFREQ = 0V fHIGH Highest Fixed Frequency VFREQ = INTVCC fSYNC Synchronizable Frequency PLLIN/MODE = External Clock l 320 350 485 535 75 kHz kHz 380 kHz 585 kHz 850 kHz 0.4 V ±1 μA –8 % PGOOD1 and PGOOD2 Outputs VPGL PGOOD Voltage Low IPGOOD = 2mA IPGOOD PGOOD Leakage Current VPGOOD = 5V VPG PGOOD Trip Level 0.2 VFB with Respect to Set Regulated Voltage VFB Ramping Negative –12 Hysteresis 2.5 VFB Ramping Positive tPGOOD(DELAY) PGOOD Delay –10 8 10 % 12 % Hysteresis 2.5 % PGOOD Going High to Low 25 μs VSW1,2 = 12V; VBOOST1,2 – VSW1,2 = 4.5V; FREQ = 0V, Forced Continuous or Pulse-Skipping Mode 55 μA BOOST1 and BOOST2 Charge Pump IBOOST1,2 BOOST Charge Pump Available Output Current Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC3788-1 is tested under pulsed load conditions such that TJ ≈ TA. The LTC3788E-1 is guaranteed to meet specifications from 0°C to 85°C junction temperature. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC3788I-1 is guaranteed over the full –40°C to 125°C operating junction temperature range. Note that the maximum ambient temperature consistent with these specifications is determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. The junction temperature (TJ, in °C) is calculated from the ambient temperature (TA, in °C) and power dissipation (PD, in Watts) according to the formula: TJ = TA + (PD • θJA), where θJA = 80°C/W. Note 3: This IC includes overtemperature protection that is intended to protect the device during momentary overload conditions. The maximum rated junction temperature will be exceeded when this protection is active. Continuous operation above the specified absolute maximum operating junction temperature may impair device reliability or permanently damage the device. Note 4: The LTC3788-1 is tested in a feedback loop that servos VFB to the output of the error amplifier while maintaining ITH at the midpoint of the current limit range. Note 5: Dynamic supply current is higher due to the gate charge being delivered at the switching frequency. Note 6: Rise and fall times are measured using 10% and 90% levels. Delay times are measured using 50% levels. Note 7: See Minimum On-Time Considerations in the Applications Information section. 37881fa 4 LTC3788-1 TYPICAL PERFORMANCE CHARACTERISTICS Efficiency and Power Loss vs Output Current Efficiency and Power Loss vs Output Current 100 10000 100 90 1000 50 10 40 30 20 VIN = 12V VOUT = 24V FIGURE 9 CIRCUIT 10 0 0.01 1 0.1 10 0.1 1 OUTPUT CURRENT (A) 1000 80 70 100 60 50 10 40 30 VIN = 12V 1 VOUT = 24V 10 Burst Mode OPERATION FIGURE 9 CIRCUIT 0.1 0 0.00001 0.0001 0.001 0.01 0.1 1 10 OUTPUT CURRENT (A) 20 37881 G02 37881 G01 BURST EFFICIENCY PULSE-SKIPPING EFFICIENCY CCM EFFICIENCY BURST LOSS PULSE-SKIPPING LOSS CCM LOSS BURST EFFICIENCY BURST LOSS Load Step Forced Continuous Mode Efficiency vs Input Voltage 100 ILOAD = 2A FIGURE 9 CIRCUIT 99 LOAD STEP 2A/DIV 98 EFFICIENCY (%) POWER LOSS (mW) 100 60 POWER LOSS (mW) 70 EFFICIENCY (%) 80 EFFICIENCY (%) 10000 90 VOUT = 12V 97 96 INDUCTOR CURRENT 5A/DIV VOUT = 24V 95 94 93 VOUT 500mV/DIV 92 91 90 0 5 15 10 INPUT VOLTAGE (V) 20 25 200μs/DIV VIN = 12V VOUT = 24V FIGURE 9 CIRCUIT 37881 G03 Load Step Pulse-Skipping Mode Load Step Burst Mode Operation LOAD STEP 2A/DIV LOAD STEP 2A/DIV INDUCTOR CURRENT 5A/DIV INDUCTOR CURRENT 5A/DIV VOUT 500mV/DIV VOUT 500mV/DIV 200μs/DIV VIN = 12V VOUT = 24V FIGURE 9 CIRCUIT 37881 G04 37881 G05 200μs/DIV VIN = 12V VOUT = 24V FIGURE 9 CIRCUIT 37881 G06 37881fa 5 LTC3788-1 TYPICAL PERFORMANCE CHARACTERISTICS Inductor Current at Light Load Soft Start-Up FORCED CONTINUOUS MODE Burst Mode OPERATION 5A/DIV VOUT 5V/DIV PULSE-SKIPPING MODE 0V 37881 G07 5μs/DIV VIN = 12V VOUT = 24V ILOAD = 200μA FIGURE 9 CIRCUIT VIN = 12V 20ms/DIV VOUT = 24V FIGURE 9 CIRCUIT Regulated Feedback Voltage vs Temperature Soft-Start Pull-Up Current vs Temperature 1.212 11.0 1.209 SOFT-START CURRENT (μA) REGULATED FEEDBACK VOLTAGE (V) 37881 G08 1.206 1.203 1.200 1.197 1.194 10.5 10.0 9.5 1.191 1.188 –45 –20 80 55 30 TEMPERATURE (°C) 5 105 9.0 –45 –20 130 5 55 80 30 TEMPERATURE (°C) 37881 G09 10.5 130 37881 G10 Shutdown Current vs Input Voltage Shutdown Current vs Temperature 11.0 105 20 VIN = 12V SHUTDOWN CURRENT (μA) SHUTDOWN CURRENT (μA) 10.0 9.5 9.0 8.5 8.0 7.5 7.0 6.5 15 10 5 6.0 5.5 5.0 –45 –20 5 55 80 30 TEMPERATURE (°C) 105 130 37881 G11 0 0 5 10 15 20 25 30 INPUT VOLTAGE (V) 35 40 37881 G12 37881fa 6 LTC3788-1 TYPICAL PERFORMANCE CHARACTERISTICS Shutdown (RUN) Threshold vs Temperature Quiescent Current vs Temperature 170 4.4 1.40 VIN = 12V VFB = 1.25V 160 RUN2 = GND 4.3 1.35 150 140 130 120 RUN RISING 1.30 1.25 1.20 RUN FALLING 1.15 100 –45 –20 1.10 –45 –20 4.0 3.9 INTVCC FALLING 3.8 3.7 3.5 80 55 30 TEMPERATURE (°C) 5 105 130 80 55 30 TEMPERATURE (°C) 5 105 3.4 –45 –20 130 EXTVCC Switchover and INTVCC Voltages vs Temperature 5.50 5.4 5.8 5.45 5.1 5.0 4.9 4.8 4.7 INTVCC 5.2 5.0 EXTVCC RISING 4.8 EXTVCC FALLING 4.6 5.30 5.25 5.20 4.4 5.10 5.05 4.5 4.0 –45 15 20 25 30 INPUT VOLTAGE (V) 35 40 5.00 –20 37881 G16 55 30 5 80 TEMPERATURE (°C) 105 Oscillator Frequency vs Input Voltage 600 360 FREQ = INTVCC Maximum Current Sense Threshold vs ITH Voltage FREQ = GND 358 OSCILLATOR FREQUENCY (kHz) 550 500 450 400 FREQ = GND 350 356 354 352 350 348 346 344 342 –20 55 30 5 80 TEMPERATURE (°C) 105 130 37881 G19 20 40 60 80 100 120 140 160 180 200 INTVCC LOAD CURRENT (mA) 37881 G18 37881 G17 Oscillator Frequency vs Temperature 300 –45 0 130 MAXIMUM CURRENT SENSE VOLTAGE (mV) 10 EXTVCC = 6V 5.15 4.2 5 EXTVCC = 0V 5.35 4.6 0 130 37881 G15 VIN = 12V 5.40 5.6 5.4 INTVCC VOLTAGE (V) EXTVCC AND INTVCC VOLTAGE (V) 6.0 5.2 105 INTVCC vs INTVCC Load Current 5.5 5.3 5 55 80 30 TEMPERATURE (°C) 37881 G14 INTVCC Line Regulation INTVCC VOLTAGE (V) 4.1 3.6 110 37881 G13 FREQUENCY (kHz) INTVCC RISING 4.2 INTVCC VOLTAGE (V) RUN PIN VOLTAGE (V) QUIESCENT CURRENT (μA) Undervoltage Lockout Threshold vs Temperature 120 PULSE-SKIPPING MODE FORCED CONTINUOUS MODE Burst Mode OPERATION 100 80 60 40 20 0 –20 –40 –60 340 5 10 25 30 20 15 INPUT VOLTAGE (V) 35 40 37881 G20 0 0.2 0.4 0.6 0.8 1.0 ITH VOLTAGE (V) 1.2 1.4 37881 G21 37881fa 7 LTC3788-1 TYPICAL PERFORMANCE CHARACTERISTICS 105 130 260 240 220 200 180 160 140 120 100 80 60 40 20 0 VSENSE = 12V SENSE+ PIN SENSE – PIN 0 0.5 37881 G22 2 1.5 1 ITH VOLTAGE (V) 2.5 3 37881 G23 Maximum Current Sense Threshold vs Duty Cycle 260 240 220 200 180 160 140 120 100 80 60 40 20 0 SENSE+ PIN SENSE – PIN 2.5 7.5 12.5 17.5 22.5 27.5 32.5 37.5 VSENSE COMMON MODE VOLTAGE (V) 37881 G24 Charge Pump Charging Current vs Operating Frequency 80 120 CHARGE PUMP CHARGING CURRENT (μA) MAXIMUM CURRENT SENSE VOLTAGE (mV) SENSE Pin Input Current vs VSENSE Voltage SENSE CURRENT (μA) 260 VSENSE = 12V 240 220 SENSE+ PIN 200 180 160 140 120 100 80 60 40 20 SENSE – PIN 0 55 30 –45 –20 5 80 TEMPERATURE (°C) SENSE Pin Input Current vs ITH Voltage SENSE CURRENT (μA) SENSE CURRENT (μA) SENSE Pin Input Current vs Temperature 100 80 60 40 20 0 0 10 20 30 40 50 60 70 80 90 100 DUTY CYCLE (%) VSW = 12V 70 VBOOST – VSW = 4.5V T = –45°C 60 T = 25°C 50 40 T = 130°C 30 20 10 0 50 150 250 350 450 550 650 750 OPERATING FREQUENCY (kHz) 37881 G26 37881 G25 PIN FUNCTIONS ITH1, ITH2 (Pin 1, Pin 13): Current Control Threshold and Error Amplifier Compensation Point. The voltage on this pin sets the current trip threshold. VFB1, VFB2 (Pin 2, Pin 12): Error Amplifier Feedback Input. This pin receives the remotely sensed feedback voltage from an external resistive divider connected across the output. SENSE1+, SENSE2+ (Pin 3, Pin 11): Positive Current Sense Comparator Input. The (+) input to the current comparator is normally connected to the positive terminal of a current sense resistor. The current sense resistor is normally placed at the input of the boost controller in series with the inductor. This pin also supplies power to the current comparator. 37881fa 8 LTC3788-1 PIN FUNCTIONS SENSE1–, SENSE2– (Pin 4, Pin 10): Negative Current Sense Comparator Input. The (–) input to the current comparator is normally connected to the negative terminal of a current sense resistor connected in series with the inductor.The common mode voltage range on these pins is 2.5V to 38V (40V abs max). FREQ (Pin 5): The frequency control pin for the internal VCO. Connecting the pin to GND forces the VCO to a fixed low frequency of 350kHz. Connecting the pin to INTVCC forces the VCO to a fixed high frequency of 535kHz. The frequency can be programmed from 50kHz to 900kHz by connecting a resistor from the FREQ pin to GND. The resistor and an internal 20μA source current create a voltage used by the internal oscillator to set the frequency. Alternatively, this pin can be driven with a DC voltage to vary the frequency of the internal oscillator. PLLIN/MODE (Pin 6): External Synchronization Input to Phase Detector and Forced Continuous Mode Input. When an external clock is applied to this pin, it will force the controller into forced continuous mode of operation and the phase-locked loop will force the rising BG1 signal to be synchronized with the rising edge of the external clock. When not synchronizing to an external clock, this input, which acts on both controllers, determines how the LTC3788-1 operates at light loads. Pulling this pin to ground selects Burst Mode operation. An internal 100k resistor to ground also invokes Burst Mode operation when the pin is floated. Tying this pin to INTVCC forces continuous inductor current operation. Tying this pin to a voltage greater than 1.2V and less than INTVCC – 1.3V selects pulse-skipping operation. This can be done by adding a 100k resistor between the PLLIN/MODE pin and INTVCC. SGND (Pin 7): Signal Ground. All small-signal components and compensation components should connect to this ground, which in turn connects to PGND at a single point. RUN1, RUN2 (Pin 8, Pin 9): Run Control Input. An external resistor divider connects to VIN and sets the thresholds for converter operation with a threshold of 1.28V. Once running, a 4.5μA current is sourced from the RUN pin allowing the user to program hysteresis using the resistor values. INTVCC (Pin 19): Output of Internal 5.4V LDO. Power supply for control circuits and gate drives. Decouple this pin to GND with a minimum 4.7μF low ESR tantalum or ceramic capacitor. EXTVCC (Pin 20): External Power Input. When this pin is higher than 4.8V an internal switch bypasses the internal regulator and supply power to INTVCC directly from EXTVCC. PGND (Pin 21): Driver Power Ground. Connects to the sources of bottom (main) N-channel MOSFETs and the (–) terminal(s) of CIN and COUT. VBIAS (Pin 22): Main Supply Pin. It is normally tied to the input supply VIN or to the output of the boost converter. A bypass capacitor should be tied between this pin and the signal ground pin.The operating voltage range on this pin is 4.5V to 38V (40V abs max). BG1, BG2 (Pin 23, Pin 18): Bottom Gate. Connect to the gate of the main NMOS. BOOST1, BOOST2 (Pin 24, Pin 17): Floating power supply for the synchronous NMOS. Bypass to SW with a capacitor and supply with a Schottky diode connected to INTVCC. TG1, TG2 (Pin 25, Pin 16): Top Gate. Connect to the gate of the synchronous NMOS. SW1, SW2 (Pin 26, Pin 15): Switch Node. Connect to the source of the synchronous NMOS, the drain of the main NMOS and the inductor. PGOOD1 (Pin 27): Power Good Indicator for Channel 1. Open-drain logic output that is pulled to ground when the output voltage is more than ±10% away from the regulated output voltage. To avoid false trips the output voltage must be outside the range for 25μs before this output is activated. SS1, SS2 (Pin 28, Pin 14): Output Soft-Start Input. A capacitor to ground at this pin sets the ramp rate of the output voltage during start-up. 37881fa 9 LTC3788-1 BLOCK DIAGRAM INTVCC DUPLICATE FOR SECOND CONTROLLER CHANNEL PGOOD1 1.32V + S – R VFB1 Q CB TG SHDN + 1.08V DB BOOST SWITCHING LOGIC AND CHARGE PUMP – 20μA FREQ COUT INTVCC CLK2 VCO VOUT SW BG 0.425V CLK1 + SLEEP PGND – PFD + – + – + + – L – SENSE – 2mV 2.8V 0.7V PLLIN/ MODE SENSE+ SLOPE COMP SYNC DET RSENSE VIN CIN + SENS LO 100k – VFB 2.5V + EA – – 1.2V SS + OV VBIAS 0.5μA/ 4.5μA SHDN EXTVCC – 1.32V ITH CC2 10μA 5.4V LDO EN + 4.8V 5.4V LDO EN RC 11V – + 3.8V INTVCC CC SGND SHDN RUN SENS LO SS – CSS 37881 BD 37881fa 10 LTC3788-1 OPERATION (Refer to Block Diagram) Main Control Loop The LTC3788-1 uses a constant-frequency, current mode step-up architecture with the two controller channels operating 180 degrees out-of-phase. During normal operation, each external bottom MOSFET is turned on when the clock for that channel sets the RS latch, and is turned off when the main current comparator, ICMP, resets the RS latch. The peak inductor current at which ICMP trips and resets the latch is controlled by the voltage on the ITH pin, which is the output of the error amplifier EA. The error amplifier compares the output voltage feedback signal at the VFB pin, (which is generated with an external resistor divider connected across the output voltage, VOUT, to ground) to the internal 1.200V reference voltage. When the load current increases, it causes a slight decrease in VFB relative to the reference, which causes the EA to increase the ITH voltage until the average inductor current matches the new load current. After the bottom MOSFET is turned off each cycle, the top MOSFET is turned on until either the inductor current starts to reverse, as indicated by the current comparator IR, or the beginning of the next clock cycle. INTVCC /EXTVCC Power Power for the top and bottom MOSFET drivers and most other internal circuitry is derived from the INTVCC pin. When the EXTVCC pin is left open or tied to a voltage less than 4.8V, the VBIAS LDO (low dropout linear regulator) supplies 5.4V from VBIAS to INTVCC. If EXTVCC is taken above 4.8V, the VBIAS LDO is turned off and an EXTVCC LDO is turned on. Once enabled, the EXTVCC LDO supplies 5.4V from EXTVCC to INTVCC. Using the EXTVCC pin allows the INTVCC power to be derived from a high efficiency external source such as one of the LTC3788-1 switching regulator outputs. Shutdown and Start-Up (RUN1, RUN2 and SS1, SS2 Pins) The two channels of the LTC3788-1 can be independently shut down using the RUN1 and RUN2 pins. Pulling either of these pins below 1.28V shuts down the main control loop for that controller. Pulling both pins below 0.7V disables both controllers and most internal circuits, including the INTVCC LDO’s. In this state, the LTC3788-1 draws only 8μA of quiescent current. The RUN pin may be externally pulled up or driven directly by logic. When driving the RUN pin with a low impedance source, do not exceed the absolute maximum rating of 8V. The RUN pin has an internal 11V voltage clamp that allows the RUN pin to be connected through a resistor to a higher voltage (for example, VIN), as long as the maximum current into the RUN pin does not exceed 100μA. The start-up of each controller’s output voltage VOUT is controlled by the voltage on the SS pin for that channel. When the voltage on the SS pin is less than the 1.2V internal reference, the LTC3788-1 regulates the VFB voltage to the SS pin voltage instead of the 1.2V reference. This allows the SS pin to be used to program a soft-start by connecting an external capacitor from the SS pin to SGND. An internal 10μA pull-up current charges this capacitor creating a voltage ramp on the SS pin. As the SS voltage rises linearly from 0V to 1.2V (and beyond up to INTVCC), the output voltage VOUT rises smoothly to its final value. Light Load Current Operation—Burst Mode Operation, Pulse-Skipping or Continuous Conduction (PLLIN/MODE Pin) The LTC3788-1 can be enabled to enter high efficiency Burst Mode operation, constant-frequency pulse-skipping mode or forced continuous conduction mode at low load currents. To select Burst Mode operation, tie the PLLIN/ MODE pin to a ground (e.g., SGND). To select forced continuous operation, tie the PLLIN/MODE pin to INTVCC. To select pulse-skipping mode, tie the PLLIN/MODE pin to a DC voltage greater than 1.2V and less than INTVCC – 0.5V. When a controller is enabled for Burst Mode operation, the minimum peak current in the inductor is set to approximately 30% of the maximum sense voltage even though the voltage on the ITH pin indicates a lower value. If the average inductor current is higher than the load current, the error amplifier EA will decrease the voltage on the ITH pin. When the ITH voltage drops below 0.425V, the internal sleep signal goes high (enabling sleep mode) and both external MOSFETs are turned off. 37881fa 11 LTC3788-1 OPERATION In sleep mode, much of the internal circuitry is turned off, reducing the quiescent current that the LTC3788-1 draws. If one channel is shut down and the other channel is in sleep mode, the LTC3788-1 draws only 125μA of quiescent current. If both channels are in sleep mode, the LTC3788-1 draws only 200μA of quiescent current. In sleep mode, the load current is supplied by the output capacitor. As the output voltage decreases, the EA’s output begins to rise. When the output voltage drops enough, the ITH pin is reconnected to the output of the EA, the sleep signal goes low, and the controller resumes normal operation by turning on the bottom external MOSFET on the next cycle of the internal oscillator. exhibits low output ripple as well as low audio noise and reduced RF interference as compared to Burst Mode operation. It provides higher low current efficiency than forced continuous mode, but not nearly as high as Burst Mode operation. When a controller is enabled for Burst Mode operation, the inductor current is not allowed to reverse. The reverse current comparator (IR) turns off the top external MOSFET just before the inductor current reaches zero, preventing it from reversing and going negative. Thus, the controller operates in discontinuous current operation. The switching frequency of the LTC3788-1’s controllers can be selected using the FREQ pin. In forced continuous operation or when clocked by an external clock source to use the phase-locked loop (see the Frequency Selection and Phase-Locked Loop section), the inductor current is allowed to reverse at light loads or under large transient conditions. The peak inductor current is determined by the voltage on the ITH pin, just as in normal operation. In this mode, the efficiency at light loads is lower than in Burst Mode operation. However, continuous operation has the advantages of lower output voltage ripple and less interference to audio circuitry, as it maintains constant-frequency operation independent of load current. When the PLLIN/MODE pin is connected for pulse-skipping mode, the LTC3788-1 operates in PWM pulse-skipping mode at light loads. In this mode, constant-frequency operation is maintained down to approximately 1% of designed maximum output current. At very light loads, the current comparator ICMP may remain tripped for several cycles and force the external bottom MOSFET to stay off for the same number of cycles (i.e., skipping pulses). The inductor current is not allowed to reverse (discontinuous operation). This mode, like forced continuous operation, Frequency Selection and Phase-Locked Loop (FREQ and PLLIN/MODE Pins) The selection of switching frequency is a trade-off between efficiency and component size. Low frequency operation increases efficiency by reducing MOSFET switching losses, but requires larger inductance and/or capacitance to maintain low output ripple voltage. If the PLLIN/MODE pin is not being driven by an external clock source, the FREQ pin can be tied to SGND, tied to INTVCC , or programmed through an external resistor. Tying FREQ to SGND selects 350kHz while tying FREQ to INTVCC selects 535kHz. Placing a resistor between FREQ and SGND allows the frequency to be programmed between 50kHz and 900kHz, as shown in Figure 6. A phase-locked loop (PLL) is available on the LTC3788-1 to synchronize the internal oscillator to an external clock source that is connected to the PLLIN/MODE pin. The LTC3788-1’s phase detector adjusts the voltage (through an internal lowpass filter) of the VCO input to align the turn-on of the first controller’s external bottom MOSFET to the rising edge of the synchronizing signal. Thus, the turn-on of the second controller’s external bottom MOSFET is 180 degrees out-of-phase to the rising edge of the external clock source. The VCO input voltage is prebiased to the operating frequency set by the FREQ pin before the external clock is applied. If prebiased near the external clock frequency, the PLL loop only needs to make slight changes to the VCO input in order to synchronize the rising edge of the external clock’s to the rising edge of BG1. The ability to prebias the loop filter allows the PLL to lock-in rapidly without deviating far from the desired frequency. 37881fa 12 LTC3788-1 OPERATION The typical capture range of the LTC3788-1’s PLL is from approximately 55kHz to 1MHz, and is guaranteed to lock to an external clock source whose frequency is between 75kHz and 850kHz. The typical input clock thresholds on the PLLIN/MODE pin are 1.6V (rising) and 1.2V (falling). Operation When VIN > VOUT When VIN rises above the regulated VOUT voltage, the boost controller can behave differently depending on the mode, inductor current and VIN voltage. In forced continuous mode, the loop works to keep the top MOSFET on continuously once VIN rises above VOUT. The internal charge pump delivers current to the boost capacitor to maintain a sufficiently high TG voltage. In pulse-skipping mode, if VIN is between 100% and 110% of the regulated VOUT voltage, TG turns on if the inductor current rises above a certain threshold and turns off if the inductor current falls below this threshold. This threshold current is set approximately to 4% of the maximum current. If the controller is programmed to Burst Mode operation under this same VIN window, then TG remains off regardless of the inductor current. If VIN rises above 110% of the regulated VOUT voltage in any mode, the controller turns on TG regardless of the inductor current. In Burst Mode operation, however, the internal charge pump turns off if the entire chip is asleep (the other channel is asleep or shut down). With the charge pump off, there would be nothing to prevent the boost capacitor from discharging, resulting in an insufficient TG voltage needed to keep the top MOSFET completely on. To prevent excessive power dissipation across the body diode of the top MOSFET in this situation, the chip can be switched over to forced continuous mode to enable the charge pump, or a Schottky diode can also be placed in parallel to the top MOSFET. Power Good The PGOOD1 pin is connected to an open-drain of an internal N-channel MOSFET. The MOSFET turns on and pulls the PGOOD1 pin low when the corresponding VFB1 pin voltage is not within ±10% of the 1.2V reference voltage. The PGOOD1 pin is also pulled low when the corresponding RUN1 pin is low (shut down). When the VFB1 pin voltage is within the ±10% requirement, the MOSFET is turned off and the pin is allowed to be pulled up by an external resistor to a source of up to 6V. Operation at Low SENSE Pin Common Voltage The current comparator in the LTC3788-1 is powered directly from the SENSE + pin. This enables the common mode voltage of SENSE + and SENSE – pins to operate at as low as 2.5V, which is below the UVLO threshold. Figure 1 shows a typical application when the controller’s VBIAS is powered from VOUT while VIN supply can go as low as 2.5V. If the voltage on SENSE + drops below 2.5V, the SS pin will be held low. When the SENSE voltage returns to the normal operating range, the SS pin will be released, initiating a new soft-start cycle. BOOST Supply Refresh and Internal Charge Pump Each top MOSFET driver is biased from the floating bootstrap capacitor CB, which normally recharges during each cycle through an external diode when the bottom MOSFET turns on. There are two considerations to keep the BOOST supply at the required bias level. During start-up, if the bottom MOSFET is not turned on within 100μs after UVLO goes low, the bottom MOSFET will be forced to turn on for ~400ns. This forced refresh generates enough BOOST-SW voltage to allow the top MOSFET ready to be fully enhanced instead of waiting for the initial few cycles to charge up. There is also an internal charge pump that keeps the required bias on BOOST. The charge pump always operates in both forced continuous mode and pulse-skipping mode. In Burst Mode operation, the charge pump is turned off during sleep and enabled when the chip wakes up. The internal charge pump can normally supply a charging current of 55μA. 37881fa 13 LTC3788-1 APPLICATIONS INFORMATION The Typical Application on the first page is a basic LTC3788-1 application circuit. LTC3788-1 can be configured to use either inductor DCR (DC resistance) sensing or a discrete sense resistor (RSENSE) for current sensing. The choice between the two current sensing schemes is largely a design trade-off between cost, power consumption and accuracy. DCR sensing is becoming popular because it does not require current sensing resistors and is more power-efficient, especially in high current applications. However, current sensing resistors provide the most accurate current limits for the controller. Other external component selection is driven by the load requirement, and begins with the selection of RSENSE (if RSENSE is used) and inductor value. Next, the power MOSFETs are selected. Finally, input and output capacitors are selected. TO SENSE FILTER, NEXT TO THE CONTROLLER VIN INDUCTOR OR RSENSE 37881 F01 Figure 1. Sense Lines Placement with Inductor or Sense Resistor VBIAS SENSE+ and SENSE– Pins The SENSE + and SENSE – pins are the inputs to the current comparators. The common mode input voltage range of the current comparators is 2.5V to 38V. The current sense resistor is normally placed at the input of the boost controller in series with the inductor. The SENSE + pin also provides power to the current comparator. It draws ~200μA during normal operation. There is a small base current of less than 1μA that flows into the SENSE – pin. The high impedance SENSE – input to the current comparators allow accurate DCR sensing. Filter components mutual to the sense lines should be placed close to the LTC3788-1, and the sense lines should run close together to a Kelvin connection underneath the current sense element (shown in Figure 1). Sensing current elsewhere can effectively add parasitic inductance and capacitance to the current sense element, degrading the information at the sense terminals and making the programmed current limit unpredictable. If DCR sensing is used (Figure 2b), sense resistor R1 should be placed close to the switching node, to prevent noise from coupling into sensitive small-signal nodes. VBIAS VIN VIN SENSE+ SENSE+ C1 (OPTIONAL) R2 DCR SENSE– SENSE– INTVCC INTVCC R1 LTC3788-1 LTC3788-1 BOOST BOOST TG TG VOUT SW INDUCTOR L VOUT SW BG BG SGND SGND 37881 F02b 37881 F02a PLACE C1 NEAR SENSE PINS (2a) Using a Resistor to Sense Current (R1||R2) • C1 = L DCR RSENSE(EQ) = DCR • R2 R1 + R2 (2b) Using the Inductor DCR to Sense Current Figure 2. Two Different Methods of Sensing Current 37881fa 14 LTC3788-1 APPLICATIONS INFORMATION Sense Resistor Current Sensing A typical sensing circuit using a discrete resistor is shown in Figure 2a. RSENSE is chosen based on the required output current. The current comparator has a maximum threshold VSENSE(MAX). The current comparator threshold sets the peak of the inductor current, yielding a maximum average output current, IMAX, equal to the peak value less half the peak-to-peak ripple current, ΔIL. To calculate the sense resistor value, use the equation: R SENSE = VSENSE(MAX ) IMAX + Δ IL 2 When using the controller in low VIN and very high voltage output applications, the maximum output current level will be reduced due to the internal compensation required to meet stability criterion for boost regulators operating at greater than 50% duty factor. A curve is provided in the Typical Performance Characteristics section to estimate this reduction in peak output current level depending upon the operating duty factor. Inductor DCR Sensing For applications requiring the highest possible efficiency at high load currents, the LTC3788-1 is capable of sensing the voltage drop across the inductor DCR, as shown in Figure 2b. The DCR of the inductor can be less than 1mΩ for high current inductors. In a high current application requiring such an inductor, conduction loss through a sense resistor could reduce the efficiency by a few percent compared to DCR sensing. If the external R1||R2 • C1 time constant is chosen to be exactly equal to the L/DCR time constant, the voltage drop across the external capacitor is equal to the drop across the inductor DCR multiplied by R2/(R1 + R2). R2 scales the voltage across the sense terminals for applications where the DCR is greater than the target sense resistor value. To properly dimension the external filter components, the DCR of the inductor must be known. It can be measured using a good RLC meter, but the DCR tolerance is not always the same and varies with temperature. Consult the manufacturer’s data sheets for detailed information. Using the inductor ripple current value from the inductor value calculation section, the target sense resistor value is: VSENSE(MAX ) R SENSE(EQUIV ) = ΔI IMAX + L 2 To ensure that the application will deliver full load current over the full operating temperature range, choose the minimum value for the maximum current sense threshold (VSENSE(MAX)). Next, determine the DCR of the inductor. Where provided, use the manufacturer’s maximum value, usually given at 20°C. Increase this value to account for the temperature coefficient of resistance, which is approximately 0.4%/°C. A conservative value for the maximum inductor temperature (TL(MAX)) is 100°C. To scale the maximum inductor DCR to the desired sense resistor value, use the divider ratio: R SENSE(EQUIV ) RD = DCRMAX at TL(MAX ) C1 is usually selected to be in the range of 0.1μF to 0.47μF. This forces R1|| R2 to around 2k, reducing error that might have been caused by the SENSE + pin’s ±1μA current. The equivalent resistance R1|| R2 is scaled to the room temperature inductance and maximum DCR: L R1|| R2 = (DCR at 20 °C) • C1 The sense resistor values are: R1 • RD R1|| R2 R1 = ; R2 = RD 1 − RD The maximum power loss in R1 is related to duty cycle, and will occur in continuous mode at VIN = 1/2 VOUT: (V − VIN ) • VIN PLOSS R1 = OUT R1 37881fa 15 LTC3788-1 APPLICATIONS INFORMATION Ensure that R1 has a power rating higher than this value. If high efficiency is necessary at light loads, consider this power loss when deciding whether to use DCR sensing or sense resistors. Light load power loss can be modestly higher with a DCR network than with a sense resistor, due to the extra switching losses incurred through R1. However, DCR sensing eliminates a sense resistor, reduces conduction losses and provides higher efficiency at heavy loads. Peak efficiency is about the same with either method. Inductor Value Calculation The operating frequency and inductor selection are interrelated in that higher operating frequencies allow the use of smaller inductor and capacitor values. Why would anyone ever choose to operate at lower frequencies with larger components? The answer is efficiency. A higher frequency generally results in lower efficiency because of MOSFET gate charge and switching losses. In addition to this basic trade-off, the effect of inductor value on ripple current and low current operation must also be considered. The inductor value has a direct effect on ripple current. The inductor ripple current ΔIL decreases with higher inductance or frequency and increases with higher VIN: V ⎛ V ⎞ ΔIL = IN ⎜ 1 − IN ⎟ f •L ⎝ VOUT ⎠ Accepting larger values of ΔIL allows the use of low inductances, but results in higher output voltage ripple and greater core losses. A reasonable starting point for setting ripple current is ΔIL = 0.3(IMAX). The maximum ΔIL occurs at VIN = 1/2 VOUT. The inductor value also has secondary effects. The transition to Burst Mode operation begins when the average inductor current required results in a peak current below 10% of the current limit determined by RSENSE. Lower inductor values (higher ΔIL) will cause this to occur at lower load currents, which can cause a dip in efficiency in the upper range of low current operation. In Burst Mode operation, lower inductance values will cause the burst frequency to decrease. Inductor Core Selection Once the value for L is known, the type of inductor must be selected. High efficiency converters generally cannot afford the core loss found in low cost powdered iron cores, forcing the use of more expensive ferrite or molypermalloy cores. Actual core loss is independent of core size for a fixed inductor value, but it is very dependent on inductance selected. As inductance increases, core losses go down. Unfortunately, because increased inductance requires more turns of wire, copper losses will increase. Ferrite core inductors have very low core loss and are preferred at high switching frequencies, so design goals can concentrate on copper loss and preventing saturation. Ferrite core material saturates “hard,” which means that inductance collapses abruptly when the peak design current is exceeded. This results in an abrupt increase in inductor ripple current and consequent output voltage ripple. Do not allow the core to saturate! Power MOSFET Selection Two external power MOSFETs must be selected for each controller in the LTC3788-1: one N-channel MOSFET for the bottom (main) switch, and one N-channel MOSFET for the top (synchronous) switch. The peak-to-peak gate drive levels are set by the INTVCC voltage. This voltage is typically 5.2V during start-up (see EXTVCC pin connection). Consequently, logic-level threshold MOSFETs must be used in most applications. The only exception is if low input voltage is expected (VIN < 5V); then, sub-logic level threshold MOSFETs (VGS(TH) < 3V) should be used. Pay close attention to the BVDSS specification for the MOSFETs as well; many of the logic level MOSFETs are limited to 30V or less. Selection criteria for the power MOSFETs include the on-resistance RDS(ON), Miller capacitance CMILLER, input voltage and maximum output current. Miller capacitance, CMILLER, can be approximated from the gate charge curve usually provided on the MOSFET manufacturer’s data sheet. CMILLER is equal to the increase in gate charge along the horizontal axis while the curve is approximately flat divided by the specified change in VDS. This result is then multiplied by the ratio of the application applied VDS 37881fa 16 LTC3788-1 APPLICATIONS INFORMATION to the gate charge curve specified VDS. When the IC is operating in continuous mode, the duty cycles for the top and bottom MOSFETs are given by: Main Switch Duty Cycle = VOUT − VIN VOUT Synchronous S witch Duty Cycle = VIN VOUT The MOSFET power dissipations at maximum output current are given by: PMAIN = ( VOUT − VIN )VOUT V 2IN • IOUT(MAX ) • (1 + δ ) • RDS(ON) + k • V 3OUT • 2 IOUT(MAX ) VIN • RDR • CMILLER • f PSYNC = VIN • IOUT(MAX )2 • (1 + δ ) • RDS(ON) VOUT where δ is the temperature dependency of RDS(ON) and RDR (approximately 1Ω) is the effective driver resistance at the MOSFET’s Miller threshold voltage. The constant k, which accounts for the loss caused by reverse recovery current, is inversely proportional to the gate drive current and has an empirical value of 1.7. Both MOSFETs have I2R losses while the bottom N-channel equation includes an additional term for transition losses, which are highest at low input voltages. For high VIN the high current efficiency generally improves with larger MOSFETs, while for low VIN the transition losses rapidly increase to the point that the use of a higher RDS(ON) device with lower CMILLER actually provides higher efficiency. The synchronous MOSFET losses are greatest at high input voltage when the bottom switch duty factor is low or during overvoltage when the synchronous switch is on close to 100% of the period. The term (1+ δ) is generally given for a MOSFET in the form of a normalized RDS(ON) vs Temperature curve, but δ = 0.005/°C can be used as an approximation for low voltage MOSFETs. CIN and COUT Selection The input ripple current in a boost converter is relatively low (compared with the output ripple current), because this current is continuous. The input capacitor CIN voltage rating should comfortably exceed the maximum input voltage. Although ceramic capacitors can be relatively tolerant of overvoltage conditions, aluminum electrolytic capacitors are not. Be sure to characterize the input voltage for any possible overvoltage transients that could apply excess stress to the input capacitors. The value of the CIN is a function of the source impedance, and in general, the higher the source impedance, the higher the required input capacitance. The required amount of input capacitance is also greatly affected by the duty cycle. High output current applications that also experience high duty cycles can place great demands on the input supply, both in terms of DC current and ripple current. In a boost converter, the output has a discontinuous current, so COUT must be capable of reducing the output voltage ripple. The effects of ESR (equivalent series resistance) and the bulk capacitance must be considered when choosing the right capacitor for a given output ripple voltage. The steady ripple voltage due to charging and discharging the bulk capacitance is given by: VRIPPLE = IOUT(MAX ) • ( VOUT − VIN(MIN) ) COUT • VOUT • f V where COUT is the output filter capacitor. The steady ripple due to the voltage drop across the ESR is given by: ΔVESR = IL(MAX) • ESR The LTC3788-1 can also be configured as a 2-phase single output converter where the outputs of the two channels are connected together and both channels have the same duty cycle. With 2-phase operation, the two channels of the dual switching regulator are operated 180 degrees out-of-phase. This effectively interleaves the output current pulses, greatly reducing the output capacitor ripple current. As a result, the ESR requirement of the capacitor can be relaxed. Because the ripple current in the output capacitor is a square wave, the ripple current requirements for the 37881fa 17 LTC3788-1 APPLICATIONS INFORMATION IORIPPLE /IOUT output capacitor depend on the duty cycle, the number of phases and the maximum output current. Figure 3 illustrates the normalized output capacitor ripple current as a function of duty cycle in a 2-phase configuration. To choose a ripple current rating for the output capacitor, first establish the duty cycle range based on the output voltage and range of input voltage. Referring to Figure 3, choose the worst-case high normalized ripple current as a percentage of the maximum load current. 3.25 3.00 2.75 2.50 2.25 2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 0.1 VOUT RB LTC3788-1 VFB RA 37881 F04 Figure 4. Setting Output Voltage Soft-Start (SS Pins) The start-up of each VOUT is controlled by the voltage on the respective SS pins. When the voltage on the SS pin is less than the internal 1.2V reference, the LTC3788-1 regulates the VFB pin voltage to the voltage on the SS pin instead of 1.2V. 1-PHASE 2-PHASE 0.2 0.3 0.4 0.5 0.6 0.7 0.8 DUTY CYCLE OR (1-VIN /VOUT) 0.9 37881 F03 Figure 3. Normalized Output Capacitor Ripple Current (RMS) for a Boost Converter Multiple capacitors placed in parallel may be needed to meet the ESR and RMS current handling requirements. Dry tantalum, special polymer, aluminum electrolytic and ceramic capacitors are all available in surface mount packages. Ceramic capacitors have excellent low ESR characteristics but can have a high voltage coefficient. Capacitors are now available with low ESR and high ripple current ratings (i.e., OS-CON and POSCAP). Soft-start is enabled by simply connecting a capacitor from the SS pin to ground, as shown in Figure 5. An internal 10μA current source charges the capacitor, providing a linear ramping voltage at the SS pin. The LTC3788-1 will regulate the VFB pin (and hence, VOUT) according to the voltage on the SS pin, allowing VOUT to rise smoothly from VIN to its final regulated value. The total soft-start time will be approximately: t SS = C SS • 1 . 2V 10µA LTC3788-1 SS CSS SGND 37881 F05 Figure 5. Using the SS Pin to Program Soft-Start Setting Output Voltage INTVCC Regulators The LTC3788-1 output voltages are each set by an external feedback resistor divider carefully placed across the output, as shown in Figure 4. The regulated output voltage is determined by: The LTC3788-1 features two separate internal P-channel low dropout linear regulators (LDO) that supply power at the INTVCC pin from either the VBIAS supply pin or the EXTVCC pin depending on the connection of the EXTVCC pin. INTVCC powers the gate drivers and much of the LTC3788-1’s internal circuitry. The VBIAS LDO and the EXTVCC LDO regulate INTVCC to 5.4V. Each of these can supply a peak current of 50mA and must be bypassed to ground with a minimum of 4.7μF ceramic capacitor. Good ⎛ R ⎞ VOUT = 1 . 2V ⎜ 1 + B ⎟ ⎝ RA ⎠ Great care should be taken to route the VFB line away from noise sources, such as the inductor or the SW line. 37881fa 18 LTC3788-1 APPLICATIONS INFORMATION bypassing is needed to supply the high transient currents required by the MOSFET gate drivers and to prevent interaction between the channels. High input voltage applications in which large MOSFETs are being driven at high frequencies may cause the maximum junction temperature rating for the LTC3788-1 to be exceeded. The INTVCC current, which is dominated by the gate charge current, may be supplied by either the VBIAS LDO or the EXTVCC LDO. When the voltage on the EXTVCC pin is less than 4.8V, the VBIAS LDO is enabled. In this case, power dissipation for the IC is highest and is equal to VIN • IINTVCC. The gate charge current is dependent on operating frequency, as discussed in the Efficiency Considerations section. The junction temperature can be estimated by using the equations given in Note 3 of the Electrical Characteristics. For example, the LTC3788-1 INTVCC current is limited to less than 15mA from a 40V supply when not using the EXTVCC supply: TJ = 70°C + (15mA)(40V)(90°C/W) = 125°C To prevent the maximum junction temperature from being exceeded, the input supply current must be checked while operating in continuous conduction mode (PLLIN/MODE = INTVCC) at maximum VIN. When the voltage applied to EXTVCC rises above 4.8V, the VIN LDO is turned off and the EXTVCC LDO is enabled. The EXTVCC LDO remains on as long as the voltage applied to EXTVCC remains above 4.55V. The EXTVCC LDO attempts to regulate the INTVCC voltage to 5.4V, so while EXTVCC is less than 5.4V, the LDO is in dropout and the INTVCC voltage is approximately equal to EXTVCC. When EXTVCC is greater than 5.4V, up to an absolute maximum of 6V, INTVCC is regulated to 5.4V. Significant thermal gains can be realized by powering INTVCC from an external supply. Tying the EXTVCC pin to a 5V supply reduces the junction temperature in the previous example from 125°C to 77°C: TJ = 70°C + (15mA)(5V)(90°C/W) = 77°C If more current is required through the EXTVCC LDO than is specified, an external Schottky diode can be added between the EXTVCC and INTVCC pins. Make sure that in all cases EXTVCC ≤ VBIAS. The following list summarizes possible connections for EXTVCC: EXTVCC Left Open (or Grounded). This will cause INTVCC to be powered from the internal 5.4V regulator resulting in an efficiency penalty at high input voltages. EXTVCC Connected to an External Supply. If an external supply is available in the 5.4V to 6V range, it may be used to power EXTVCC providing it is compatible with the MOSFET gate drive requirements. Ensure that EXTVCC < VBIAS. Topside MOSFET Driver Supply (CB, DB) External bootstrap capacitors CB connected to the BOOST pins supply the gate drive voltages for the topside MOSFETs. Capacitor CB in the Block Diagram is charged though external diode DB from INTVCC when the SW pin is low. When one of the topside MOSFETs is to be turned on, the driver places the CB voltage across the gate-source of the desired MOSFET. This enhances the MOSFET and turns on the topside switch. The switch node voltage, SW, rises to VIN and the BOOST pin follows. With the topside MOSFET on, the boost voltage is above the input supply: VBOOST = VIN + VINTVCC. The value of the boost capacitor CB needs to be 100 times that of the total input capacitance of the topside MOSFET(s). The reverse breakdown of the external Schottky diode must be greater than VIN(MAX). Fault Conditions: Overtemperature Protection At higher temperatures, or in cases where the internal power dissipation causes excessive self-heating on chip (such as an INTVCC short to ground), the overtemperature shutdown circuitry will shut down the LTC3788-1. When the junction temperature exceeds approximately 170°C, the overtemperature circuitry disables the INTVCC LDO, causing the INTVCC supply to collapse and effectively shut down the entire LTC3788-1 chip. Once the junction temperature drops back to approximately 155°C, the INTVCC LDO turns back on. Long term overstress (TJ > 125°C) should be avoided as it can degrade the performance or shorten the life of the part. 37881fa 19 LTC3788-1 APPLICATIONS INFORMATION The LTC3788-1 has an internal phase-locked loop (PLL) comprised of a phase frequency detector, a low pass filter and a voltage-controlled oscillator (VCO). This allows the turn-on of the top MOSFET of controller 1 to be locked to the rising edge of an external clock signal applied to the PLLIN/MODE pin. The turn-on of controller 2’s top MOSFET is thus 180 degrees out-of-phase with the external clock. The phase detector is an edge-sensitive digital type that provides zero degrees phase shift between the external and internal oscillators. This type of phase detector does not exhibit false lock to harmonics of the external clock. If the external clock frequency is greater than the internal oscillator’s frequency, fOSC, then current is sourced continuously from the phase detector output, pulling up the VCO input. When the external clock frequency is less than fOSC, current is sunk continuously, pulling down the VCO input. If the external and internal frequencies are the same but exhibit a phase difference, the current sources turn on for an amount of time corresponding to the phase difference. The voltage at the VCO input is adjusted until the phase and frequency of the internal and external oscillators are identical. At the stable operating point, the phase detector output is high impedance and the internal filter capacitor, CLP, holds the voltage at the VCO input. Typically, the external clock (on PLLIN/MODE pin) input high threshold is 1.6V, while the input low threshold is 1.2V. Note that the LTC3788-1 can only be synchronized to an external clock whose frequency is within range of the LTC3788-1’s internal VCO, which is nominally 55kHz to 1MHz. This is guaranteed to be between 75kHz and 850kHz. Rapid phase locking can be achieved by using the FREQ pin to set a free-running frequency near the desired synchronization frequency. The VCO’s input voltage is prebiased at a frequency corresponding to the frequency set by the FREQ pin. Once prebiased, the PLL only needs to adjust the frequency slightly to achieve phase lock and synchronization. Although it is not required that the free-running frequency be near external clock frequency, doing so will prevent the operating frequency from passing through a large range of frequencies as the PLL locks. Table 1 summarizes the different states in which the FREQ pin can be used. Table 1. FREQ PIN PLLIN/MODE PIN FREQUENCY 0V DC Voltage 350kHz INTVCC DC Voltage 535kHz Resistor DC Voltage 50kHz to 900kHz Any of the Above External Clock Phase Locked to External Clock 1000 900 800 FREQUENCY (kHz) Phase-Locked Loop and Frequency Synchronization 700 600 500 400 300 200 100 0 15 25 35 45 55 65 75 85 95 105 115 125 FREQ PIN RESISTOR (kΩ) 37881 F06 Figure 6. Relationship Between Oscillator Frequency and Resistor Value at the FREQ Pin Minimum On-Time Considerations Minimum on-time, tON(MIN), is the smallest time duration that the LTC3788-1 is capable of turning on the bottom MOSFET. It is determined by internal timing delays and the gate charge required to turn on the top MOSFET. Low duty cycle applications may approach this minimum ontime limit. In forced continuous mode, if the duty cycle falls below what can be accommodated by the minimum on-time, the controller will begin to skip cycles but the output will continue to be regulated. More cycles will be skipped when VIN increases. Once VIN rises above VOUT, the loop works to keep the top MOSFET on continuously. The minimum on-time for the LTC3788-1 is approximately 110ns. 37881fa 20 LTC3788-1 APPLICATIONS INFORMATION Efficiency Considerations The percent efficiency of a switching regulator is equal to the output power divided by the input power times 100%. It is often useful to analyze individual losses to determine what is limiting the efficiency and which change would produce the greatest improvement. Percent efficiency can be expressed as: %Efficiency = 100% – (L1 + L2 + L3 + ...) where L1, L2, etc., are the individual losses as a percentage of input power. Although all dissipative elements in the circuit produce losses, four main sources usually account for most of the losses in LTC3788-1 circuits: 1) IC VIN current, 2) INTVCC regulator current, 3) I2R losses, 4) Bottom MOSFET transition losses. 1. The VIN current is the DC supply current given in the Electrical Characteristics table, which excludes MOSFET driver and control currents. VIN current typically results in a small (<0.1%) loss. 2. INTVCC current is the sum of the MOSFET driver and control currents. The MOSFET driver current results from switching the gate capacitance of the power MOSFETs. Each time a MOSFET gate is switched from low to high to low again, a packet of charge, dQ, moves from INTVCC to ground. The resulting dQ/dt is a current out of INTVCC that is typically much larger than the control circuit current. In continuous mode, IGATECHG = f(QT + QB), where QT and QB are the gate charges of the topside and bottom side MOSFETs. 3. DC I2R losses. These arise from the resistances of the MOSFETs, sensing resistor, inductor and PC board traces and cause the efficiency to drop at high output currents. 4. Transition losses apply only to the bottom MOSFET(s), and become significant only when operating at low input voltages (typically 15V or greater). Transition losses can be estimated from: V 3 Transition Loss = (1 . 7) OUT IO(MAX ) • CRSS f VIN Other hidden losses, such as copper trace and internal battery resistances, can account for an additional 5% to 10% efficiency degradation in portable systems. It is very important to include these system-level losses during the design phase. Checking Transient Response The regulator loop response can be checked by looking at the load current transient response. Switching regulators take several cycles to respond to a step in DC (resistive) load current. When a load step occurs, VOUT shifts by an amount equal to ΔILOAD (ESR), where ESR is the effective series resistance of COUT. ΔILOAD also begins to charge or discharge COUT generating the feedback error signal that forces the regulator to adapt to the current change and return VOUT to its steady-state value. During this recovery time VOUT can be monitored for excessive overshoot or ringing, which would indicate a stability problem. OPTI-LOOP compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The availability of the ITH pin not only allows optimization of control loop behavior, but it also provides a DC coupled and AC filtered closed loop response test point. The DC step, rise time and settling at this test point truly reflects the closed loop response. Assuming a predominantly second order system, phase margin and/or damping factor can be estimated using the percentage of overshoot seen at this pin. The bandwidth can also be estimated by examining the rise time at the pin. The ITH external components shown in Figure 9 circuit will provide an adequate starting point for most applications. The ITH series RC-CC filter sets the dominant pole-zero loop compensation. The values can be modified slightly (from 0.5 to 2 times their suggested values) to optimize transient response once the final PC layout is complete and the particular output capacitor type and value have been determined. The output capacitors must be selected because the various types and values determine the loop gain and phase. An output current pulse of 20% to 80% of full-load current having a rise time of 1μs to 10μs will produce output voltage and ITH pin waveforms that will give a sense of the overall loop stability without breaking the feedback loop. Placing a power MOSFET and load resistor directly across the output capacitor and driving the gate with an appropriate signal generator is a practical way to produce 37881fa 21 LTC3788-1 APPLICATIONS INFORMATION a realistic load step condition. The initial output voltage step resulting from the step change in output current may not be within the bandwidth of the feedback loop, so this signal cannot be used to determine phase margin. This is why it is better to look at the ITH pin signal which is in the feedback loop and is the filtered and compensated control loop response. The gain of the loop will be increased by increasing RC and the bandwidth of the loop will be increased by decreasing CC. If RC is increased by the same factor that CC is decreased, the zero frequency will be kept the same, thereby keeping the phase shift the same in the most critical frequency range of the feedback loop. The output voltage settling behavior is related to the stability of the closed-loop system and will demonstrate the actual overall supply performance. A second, more severe transient is caused by switching in loads with large (>1μF) supply bypass capacitors. The discharged bypass capacitors are effectively put in parallel with COUT, causing a rapid drop in VOUT. No regulator can alter its delivery of current quickly enough to prevent this sudden step change in output voltage if the load switch resistance is low and it is driven quickly. If the ratio of CLOAD to COUT is greater than 1:50, the switch rise time should be controlled so that the load rise time is limited to approximately 25 • CLOAD. Thus, a 10μF capacitor would require a 250μs rise time, limiting the charging current to about 200mA. Design Example As a design example for one channel, assume VIN = 12V(nominal), VIN = 22V (max), VOUT = 24V, IOUT(MAX) = 4A, VSENSE(MAX) = 75mV, and f = 350kHz. The inductance value is chosen first based on a 30% ripple current assumption. The highest value of ripple current occurs at the maximum input voltage. Tie the PLLLPF pin to GND, generating 350kHz operation. The minimum inductance for 30% ripple current is: V ⎛ V ⎞ ΔIL = IN ⎜ 1 − IN ⎟ f •L⎝ VOUT ⎠ A 6.8μH inductor will produce a 30% ripple current. The peak inductor current will be the maximum DC value plus one half the ripple current, or 9.25A. The RSENSE resistor value can be calculated by using the maximum current sense voltage specification with some accommodation for tolerances: R SENSE ≤ 75mV = 0 . 008Ω 9 . 25A Choosing 1% resistors: RA = 5k and RB = 95.3k yields an output voltage of 24.072V. The power dissipation on the top side MOSFET can be easily estimated. Choosing a Vishay Si7848BDP MOSFET results in: RDS(ON) = 0.012Ω, CMILLER = 150pF. At maximum input voltage with T(estimated) = 50°C: PMAIN = (24V − 12V) 24V (12V)2 • (4A )2 • ⎡⎣1 + (0 . 005)(50 °C − 25 °C)⎤⎦ • 0 . 008Ω + (1 . 7)(24V)3 4A (150pF )(350kHz) = 0 . 7 W 12V COUT is chosen to filter the square current in the output. The maximum output current peak is: 31 % ⎞ ⎛ IOUT(PEAK ) = 4 • ⎜ 1 + ⎟ = 4 . 62A ⎝ 2 ⎠ A low ESR (5mΩ) capacitor is suggested. This capacitor will limit output voltage ripple to 23.1mV (assuming ESR dominate ripple). PC Board Layout Checklist When laying out the printed circuit board, the following checklist should be used to ensure proper operation of the IC. These items are also illustrated graphically in the layout diagram of Figure 7. Figure 8 illustrates the current waveforms present in the various branches of the 2-phase synchronous regulators operating in the continuous mode. Check the following in your layout: 1. Put the bottom N-channel MOSFETs MBOT1 and MBOT2 and the top N-channel MOSFETs MTOP1 and MTOP2 in one compact area with COUT. 37881fa 22 LTC3788-1 APPLICATIONS INFORMATION 2. Are the signal and power grounds kept separate? The combined IC signal ground pin and the ground return of CINTVCC must return to the combined COUT (–) terminals. The path formed by the bottom N-channel MOSFET and the CIN capacitor should have short leads and PC trace lengths. The output capacitor (–) terminals should be connected as close as possible to the (–) terminals of the input capacitor by placing the capacitors next to each other. 3. Do the LTC3788-1 VFB pins’ resistive dividers connect to the (+) terminals of COUT? The resistive divider must be connected between the (+) terminal of COUT and signal ground and placed close to the VFB pin. The feedback resistor connections should not be along the high current input feeds from the input capacitor(s). 4. Are the SENSE – and SENSE + leads routed together with minimum PC trace spacing? The filter capacitor between SENSE + and SENSE – should be as close as possible to the IC. Ensure accurate current sensing with Kelvin connections at the sense resistor. 5. Is the INTVCC decoupling capacitor connected close to the IC, between the INTVCC and the power ground pins? This capacitor carries the MOSFET drivers’ current peaks. An additional 1μF ceramic capacitor placed immediately next to the INTVCC and PGND pins can help improve noise performance substantially. 6. Keep the switching nodes (SW1, SW2), top gate nodes (TG1, TG2) and boost nodes (BOOST1, BOOST2) away from sensitive small-signal nodes, especially from the opposites channel’s voltage and current sensing feedback pins. All of these nodes have very large and fast moving signals and, therefore, should be kept on the output side of the LTC3788-1 and occupy a minimal PC trace area. 7. Use a modified “star ground” technique: a low impedance, large copper area central grounding point on the same side of the PC board as the input and output capacitors with tie-ins for the bottom of the INTVCC decoupling capacitor, the bottom of the voltage feedback resistive divider and the SGND pin of the IC. PC Board Layout Debugging Start with one controller on at a time. It is helpful to use a DC-50MHz current probe to monitor the current in the inductor while testing the circuit. Monitor the output switching node (SW pin) to synchronize the oscilloscope to the internal oscillator and probe the actual output voltage. Check for proper performance over the operating voltage and current range expected in the application. The frequency of operation should be maintained over the input voltage range down to dropout and until the output load drops below the low current operation threshold— typically 10% of the maximum designed current level in Burst Mode operation. The duty cycle percentage should be maintained from cycle to cycle in a well designed, low noise PCB implementation. Variation in the duty cycle at a subharmonic rate can suggest noise pickup at the current or voltage sensing inputs or inadequate loop compensation. Overcompensation of the loop can be used to tame a poor PC layout if regulator bandwidth optimization is not required. Only after each controller is checked for its individual performance should both controllers be turned on at the same time. A particularly difficult region of operation is when one controller channel is nearing its current comparator trip point while the other channel is turning on its bottom MOSFET. This occurs around the 50% duty cycle on either channel due to the phasing of the internal clocks and may cause minor duty cycle jitter. Reduce VIN from its nominal level to verify operation with high duty cycle. Check the operation of the undervoltage lockout circuit by further lowering VIN while monitoring the outputs to verify operation. Investigate whether any problems exist only at higher output currents or only at higher input voltages. If problems coincide with high input voltages and low output currents, look for capacitive coupling between the BOOST, SW, TG, and possibly BG connections and the sensitive voltage and current pins. The capacitor placed across the current sensing pins needs to be placed immediately adjacent to the pins of the IC. This capacitor helps to minimize the effects of differential noise injection due to high frequency capacitive coupling. If problems are encountered with 37881fa 23 LTC3788-1 APPLICATIONS INFORMATION SENSE1– SENSE1+ SS1 PGOOD1 SW1 TG1 LTC3788-1 VPULL-UP L1 CB1 BOOST1 BG1 VFB1 VBIAS M2 fIN + GND FREQ PLLIN/MODE SGND RUN1 RUN2 PGND EXTVCC INTVCC BG2 VFB2 BOOST2 ITH2 TG2 SW2 CB2 VOUT1 + M1 ITH1 RSENSE1 M3 VIN + M4 VOUT2 L2 RSENSE2 SS2 SENSE2+ SENSE2– 37881 F07 Figure 7. Recommended Printed Circuit Layout Diagram 37881fa 24 LTC3788-1 APPLICATIONS INFORMATION RSENSE1 L1 SW1 VOUT1 COUT1 RL1 VIN RIN CIN RSENSE2 BOLD LINES INDICATE HIGH SWITCHING CURRENT. KEEP LINES TO A MINIMUM LENGTH. L2 SW2 VOUT2 COUT2 RL2 37881 F08 Figure 8. Branch Current Waveforms 37881fa 25 LTC3788-1 APPLICATIONS INFORMATION high current output loading at lower input voltages, look for inductive coupling between CIN, Schottky and the top MOSFET components to the sensitive current and voltage sensing traces. In addition, investigate common ground path voltage pickup between these components and the SGND pin of the IC. An embarrassing problem, which can be missed in an otherwise properly working switching regulator results RA1 12.1k RB1 232k SENSE1– SENSE1+ VFB1 CITH1 220pF CITH1 15nF PGOOD2 PGOOD1 TG1 LTC3788-1 SW1 when the current sensing leads are hooked up backwards. The output voltage under this improper hook-up will still be maintained, but the advantages of current mode control will not be realized. Compensation of the voltage loop will be much more sensitive to component selection. This behavior can be investigated by temporarily shorting out the current sensing resistor—don’t worry, the regulator will still maintain control of the output voltage. 100k INTVCC MTOP1 L1 3.3μH RSENSE1 4mΩ COUTA1 22μF s4 + COUTB1 220μF CB1 0.1μF BOOST1 RITH1 8.66k CSS1 0.1μF BG1 MBOT1 ITH1 VBIAS SS1 SS2 ITH2 VFB2 INTVCC CINT 4.7μF CINA 22μF s4 PGND BG2 PLLIN/MODE BOOST2 SGND SW2 EXTVCC RUN1 TG2 RUN2 FREQ CB1 0.1μF + VIN 5V TO 24V VOUT 24V, 10A* CINB 220μF MBOT2 L2 3.3μH RSENSE2 4mΩ MTOP2 COUTA2 22μF s4 SENSE2+ SENSE2– + COUTB2 220μF 37881 F09 CINA, COUTA1, COUTA2: SANYO, 50CE220AX CINB, COUTB1, COUTB2: TDK C4532X5R1E226M L1, L2: PULSE PA1494.362NL MBOT1, MBOT2, MTOP1, MTOP2: RENESAS HAT2169H *WHEN VIN < 8V, MAXIMUM LOAD CURRENT AVAILABLE IS REDUCED. Figure 9. High Efficiency 2-Phase 24V Boost Converter 37881fa 26 LTC3788-1 TYPICAL APPLICATIONS RS1, 53.6k, 1% RS2 26.1k, 1% RB1 232k 1% C1 0.1μF C3 0.1μF RA1 12.1k, 1% SENSE1– SENSE1+ PGOOD1 INTVCC LTC3788-1 VFB1 CITH1, 220pF CITH1, 15nF 100k D3 MTOP1 TG1 VOUT1 24V, 4A COUTB1 220μF SW1 BOOST1 RITH1 8.87k, 1% CB1, 0.1μF ITH1 MBOT1 BG1 CSS1, 0.01μF D1 SS1 INTVCC PLLIN/MODE SGND VBIAS INTVCC RUN1 RFREQ 41.2k RUN2 CINA 22μF s4 CINT 4.7μF PGND EXTVCC D2 BG2 CB1, 0.1μF CINB 220μF MBOT2B BOOST2 FREQ SS2 + VIN 5V TO 24V MBOT2A L2 16μH CSS2, 0.01μF CITH2, 4.7nF L1 10.2μH COUTA1 6.8μF s4 + SW2 RITH2 23.7k, 1% D4 ITH2 TG2 MTOP2 CITH2A, 220pF RA2 12.1k, 1% COUTA2 22μF s4 VFB2 RB2 475k 1% C4 0.1μF RS4 30.1k, 1% C2 0.1μF SENSE2+ + VOUT2 48V, 2A COUTB2 220μF SENSE2– RS3 42.2k, 1% 37881 F10 COUTA2: C4532x7R1H685K COUTB2: SANYO 63CE220KX CINA, COUTA1: TDK C4532X5R1E226M CINB, COUTB1: SANYO 50CE220AX L1: PULSE PA2050.103NL L2: PULSE PA2050.163NL MBOT1, MTOP1: RENESAS RJK0305 MBOT2A, MBOT2B, MTOP2: RENESAS RJK0652 D3: DIODES INC B340B D4: DIODES INC B360A Figure 10. High Efficiency Dual 24V/48V Boost Converter with Inductor DCR Current Sensing 37881fa 27 LTC3788-1 PACKAGE DESCRIPTION GN Package 28-Lead Plastic SSOP (Narrow .150 Inch) (Reference LTC DWG # 05-08-1641) .386 – .393* (9.804 – 9.982) .045 ±.005 28 27 26 25 24 23 22 21 20 19 18 17 1615 .254 MIN .033 (0.838) REF .150 – .165 .229 – .244 (5.817 – 6.198) .0165 ± .0015 .150 – .157** (3.810 – 3.988) .0250 BSC 1 RECOMMENDED SOLDER PAD LAYOUT .015 ± .004 × 45° (0.38 ± 0.10) .0075 – .0098 (0.19 – 0.25) 2 3 4 5 6 7 8 .0532 – .0688 (1.35 – 1.75) 9 10 11 12 13 14 .004 – .0098 (0.102 – 0.249) 0° – 8° TYP .016 – .050 (0.406 – 1.270) NOTE: 1. CONTROLLING DIMENSION: INCHES INCHES 2. DIMENSIONS ARE IN (MILLIMETERS) .008 – .012 (0.203 – 0.305) TYP .0250 (0.635) BSC GN28 (SSOP) 0204 3. DRAWING NOT TO SCALE *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 37881fa 28 LTC3788-1 REVISION HISTORY (Revision history begins at Rev A) REV DATE DESCRIPTION A 03/10 Updates to Typical Application PAGE NUMBER Updates in the Electrical Characteristics Section Updates to PLLIN/MODE in Pin Functions Updates to Application Information 1 3, 4 9 15, 19, 22 New Figure 9 Added 26 Updated Note on Typical Application 30 Updated Related Parts Table 30 37881fa Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 29 LTC3788-1 TYPICAL APPLICATION High Efficiency Dual 12V/24V Boost Converter RB1 232k 1% SENSE1– SENSE1+ RA1 12.1k, 1% 100k PGOOD1 TG1 VFB1 CITH1, 220pF L1 MTOP1 3.3μH COUTA1 22μF s4 + COUTB1 220μF SW1 LTC3788-1 BG1 ITH1 CB1, 0.1μF MBOT1 D1 CSS1, 0.1μF VBIAS SS1 INTVCC PGND PLLIN/MODE SGND BG2 EXTVCC RUN1 BOOST2 RUN2 FREQ CINA 22μF s4 CINT 4.7μF SS2 SW2 ITH2 TG2 L2 1.25μH RSENSE2 3mΩ MTOP2 RA2 12.1k COUTA2 22μF s4 VFB2 SENSE2+ SENSE2– RB2 110k CINB 220μF MBOT2 CB1, 0.1μF RITH2 2.7k CITHA2, 100pF + VIN 5V TO 24V D2 CSS2, 0.1μF CITH2, 15nF RSENSE1 4mΩ BOOST1 RITH1 8.66k CITH1, 15nF INTVCC VOUT1* 24V, 5A + VOUT2* 12V, 10A COUTB2 220μF 37881 TA02 CINA, COUTA1, COUTA2: SANYO, 50CE220AX CINB, COUTB1, COUTB2: TDK C4532X5R1E226M L1: PULSE PA1494.362NL L2: PULSE PA1294.132NL MBOT1, MBOT2, MTOP1, MTOP2: RENESAS HAT2169H * WHEN VIN < 8V, MAXIMUM LOAD CURRENT AVAILABLE IS REDUCED RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LTC3862/LTC3862-1 Multiphase Current Mode Step-Up DC/DC Controller 4V ≤ VIN ≤ 36V, 5V or 10V Gate Drive, 75kHZ to 500kHz, SSOP-24, TSSOP-24, 5mm × 5mm QFN-24 LTC3813/LTC3814-5 100V/60V Maximum VOUT Current Mode Synchronous Step-Up DC/DC Controller No RSENSE™, Large 1Ω Gate Driver, Adjustable Off-Time, SSOP-28, TSSOP-16 LTC1871/LTC1871-1/ LTC1871-7 Wide Input Range, No Rsense Low Quiescent Current Flyback, Boost and SEPIC Controller Adjustable Switching Frequency, 2.5V ≤ VIN ≤ 36V, Burst Mode® Operation at Light Load. MSOP-10 LT3757/LT3758 Boost, Flyback, SEPIC and Inverting Controller VIN Up to 40V/100V, 100kHz to 1MHz Programmable Operation Frequency, 3mm × 3mm DFN-10 and MSOP-10E LTC3780 High Efficiency Synchronous 4-Switch Buck-Boost DC/DC Controller 4V ≤ VIN ≤ 36V, 0.8V ≤ VOUT ≤ 30V, SSOP-24, 5mm × 5mm QFN-32 37881fa 30 Linear Technology Corporation LT 0410 REV A • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2009