Panasonic New Product Introduction New PAN1322 Series Place and Play Bluetooth® Module RoHS COMPLIANT All-In-One, Place and Play Bluetooth Module Introducing Panasonic’s next generation, smartphone compatible, place and play Bluetooth module, the PAN1322 Series. This module features an embedded microcontroller, Bluetooth 2.1 + EDR stack, serial port profile (SPP), AT command set API and antenna. This cost engineered solution is based on a single chip solution that integrates an ARM7TDMI processor with a Bluetooth controller. The BT 2.1 + EDR stack provides secure, reliable, high speed data connections using Secure Simple Paring (SSP) eliminating manual password creation. Embedded serial port profile (SPP) frees application resources while the AT command set API creates a simple firmware interface using modem commands. An onboard antenna does away with 2.4GHz RF circuit complexity. Created with the design engineer in mind, product design cycles are greatly reduced using Panasonic’s reference design and design review services. PCB layouts are simplified using available Gerber files and minimized with Panasonic’s tiny footprint technology. The module is and is just 15.6mm x 8.7mm x 2.8mm and fully shielded to improve immunity. GPIO is exposed using AT commands. All Panasonic Bluetooth RF modules carry FCC, IC, CE Bluetooth certifications. The PAN1322 Series recognizes Apple’s authentication coprocessor and supports Bluetooth Serial Port Profile (SPP) data communication1 with Apple’s iPhone and iPad®*. Connectivity also includes Android, smart phones and all Bluetooth enabled devices2. Panasonic remains committed to customers as a module manufacturer by extending product life using legacy footprints and firmware interfaces to make the PAN1322 Series fully compatible with the module it replaces, the PAN1321 Series. Hardware and firmware prototyping and testing are accelerated using the EVAL_PAN1322 development kit and SPP Toolbox development environment. 1. Apple authentication coprocessor and MFI certification is required. 2. Connectivity requires that devices support Bluetooth Serial Port Profile *Apple iPad and iPhone are trademarks of Apple Inc Features • Bluetooth Version 2.1 + EDR • SPP Device A and B, RFCOMM Profiles • Industrial Temperature Range, -40 to +85°C • No External Components Needed • Onboard Voltage Regulator, VIN=2.7 to 3.6 V • Integrated ARM7RDMI 32-Bit Processor w/Patchable EEPROM • 3.25 MBaud UART • GPIO w/Interrupt and Wake-Up Capabilities Website: www.panasonic.com/industrial [email protected] 1-800-344-2112 Applications • iOS and Android Devices • Wireless Sensors • Cable Replacement • Industrial • Medical • Automotive Copyright © 2013 Panasonic Corporation of North America. All Rights Reserved. Specifications are subject to change without notice. PAN1322 Series NPI, FY13-046-XXX Block Diagram (PAN1322-SPP) EEPROM VDD1 Ceramic Antenna I2C VDD_UART PMB8754 BlueMoon UniCellular UART GPIO VSUPPLY Balun Filter / Matching Voltage Regulator Crystal 26 MHz Technical Characteristics Parameter Value Condition Receiver Sensitivity -86 dBm typ. Ideal Signal Output Power +3 dBm typ. @ 50 Ohm Antenna Pin Power Supply 2.7 to 3.5 V Single Voltage Operation Ultra Low Power Mode 80 µA T = 2.5°C ACL (Transmit 3-DH1) 40 mA Enhanced Data Rate, 531.2kb/s ACL (Receive 3-DH1) 37 mA Enhanced Data Rate, 531.2kb/s Operating Temperature -40 to +85°C Ordering Information Part Number Description ENW-89841A3KF PAN1322 Bluetooth Module, SPP, Integrated Antenna EVAL_PAN1322 PAN1322 Evaluation Kit Additional Information For detailed specification information on the PAN1322 Place and Play Bluetooth Module, visit our website at: http://www.panasonic.com/rfmodules/ Website: www.panasonic.com/industrial [email protected] 1-800-344-2112 Copyright © 2013 Panasonic Corporation of North America. All Rights Reserved. Specifications are subject to change without notice. PAN1322 Series NPI, FY13-046-XXX