Micrel MIC5205-2.5BM5 150ma low-noise ldo regulator Datasheet

MIC5205
150mA Low-Noise LDO Regulator
General Description
Features
The MIC5205 is an efficient linear voltage regulator with
ultra low-noise output, very low dropout voltage (typically
17mV at light loads and 165mV at 150mA), and very low
ground current (600⎧A at 100mA output). The MIC5205
offers better than 1% initial accuracy.
Designed especially for hand-held, battery-powered
devices, the MIC5205 includes a CMOS or TTL compatible
enable/shutdown control input. When shut down, power
consumption drops nearly to zero. Regulator ground
current increases only slightly in dropout, further
prolonging battery life.
Key MIC5205 features include a reference bypass pin to
improve its already excellent low-noise performance,
reversed-battery protection, current limiting, and
overtemperature shutdown.
The MIC5205 is available in fixed and adjustable output
voltage versions in a small SOT-23-5 package.
For low-dropout regulators that are stable with ceramic
output capacitors, see the µCap MIC5245/6/7 family.
Data sheets and support documentation can be found on
Micrel’s web site at www.micrel.com.
•
•
•
•
•
•
•
•
•
•
•
Ultra-low-noise output
High output voltage accuracy
Guaranteed 150mA output
Low quiescent current
Low dropout voltage
Extremely tight load and line regulation
Very low temperature coefficient
Current and thermal limiting
Reverse-battery protection
“Zero” off-mode current
Logic-controlled electronic enable
Applications
•
•
•
•
•
•
•
Cellular telephones
Laptop, notebook, and palmtop computers
Battery-powered equipment
PCMCIA VCC and VPP regulation/switching
Consumer/personal electronics
SMPS post-regulator/dc-to-dc modules
High-efficiency linear power supplies
___________________________________________________________________________________________________________
Typical Application
Ultra-Low-Noise Regulator Application
Xxxxx is a trademark of Micrel, Inc
Xxxxx is a registered trademark of Micrel, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
February 2006
M9999-020806
(408) 955-1690
Micrel
MIC5205
Ordering Information
Part Number
Standard
Marking
Pb-Free
Standard
Pb-Free(1)
Accuracy
Voltage
Temperature
Package
MIC5205BM5
MIC5205YM5
LBAA
KBAA
1%
Adj
–40°C to +125°C
SOT-23-5
MIC5205-2.5BM5
MIC5205-2.5YM5
LB25
KB25
1%
2.5V
–40°C to +125°C
SOT-23-5
MIC5205-2.7BM5
MIC5205-2.7YM5
LB27
KB27
1%
2.7V
–40°C to +125°C
SOT-23-5
MIC5205-2.8BM5
MIC5205-2.8YM5
LB28
KB28
1%
2.8V
–40°C to +125°C
SOT-23-5
MIC5205-2.85BM5
MIC5205-2.85YM5
LB2J
KB2J
1%
2.85V
–40°C to +125°C
SOT-23-5
MIC5205-2.9BM5
MIC5205-2.9YM5
LB29
KB29
1%
2.9V
–40°C to +125°C
SOT-23-5
MIC5205-3.0BM5
MIC5205-3.0YM5
LB30
KB30
1%
3.0V
–40°C to +125°C
SOT-23-5
MIC5205-3.1BM5
MIC5205-3.1YM5
LB31
KB31
1%
3.1V
–40°C to +125°C
SOT-23-5
MIC5205-3.2BM5
MIC5205-3.2YM5
LB32
KB32
1%
3.2V
–40°C to +125°C
SOT-23-5
MIC5205-3.3BM5
MIC5205-3.3YM5
LB33
KB33
1%
3.3V
–40°C to +125°C
SOT-23-5
MIC5205-3.6BM5
MIC5205-3.6YM5
LB36
KB36
1%
3.6V
–40°C to +125°C
SOT-23-5
MIC5205-3.8BM5
MIC5205-3.8YM5
LB38
KB38
1%
3.8V
–40°C to +125°C
SOT-23-5
MIC5205-4.0BM5
MIC5205-4.0YM5
LB40
KB40
1%
4.0V
–40°C to +125°C
SOT-23-5
MIC5205-5.0BM5
MIC5205-5.0YM5
LB50
KB50
1%
5.0V
–40°C to +125°C
SOT-23-5
Note:
1. Underbar (_) symbol may not be to scale.
Pin Configuration
MIC5205-x.xBM5/YM5
Fixed Voltages
MIC5205BM5/YM5
Adjustable Voltages
Pin Description
MIC5205-x.x
(fixed)
MIC5205
(adjustable)
Pin Name
Pin Function
1
1
IN
Supply Input
2
2
GND
3
3
EN
February 2006
Enable/Shudown (Input): CMOS compatible input. Logic high = enable, logic low
or open = shutdown
BYP
Reference Bypass: Connect external 470pF capacitor to GND to reduce output
noise. May be left open.
4
ADJ
Adjust (Input): Adjustable regulator feedback input. Connect to resistor voltage
divider.
5
OUT
Regulator Ouput
4
5
Ground
2
M9999-020806
(408) 955-1690
Micrel
MIC5205
Absolute Maximum Ratings(1)
Operating Ratings(2)
Supply Input Voltage (VIN).............................. –20V to +20V
Enable Input Voltage (VEN)............................. –20V to +20V
Power Dissipation (PD) .................Internally Limited, Note 3
Lead Temperature (soldering, 5 sec.)........................ 260°C
Junction Temperature (TJ) ........................–40°C to +125°C
Storage Temperature (TS).........................–65°C to +150°C
Input Voltage (VIN)......................................... +2.5V to +16V
Enable Input Voltage (VEN).....................................0V to VIN
Junction Temperature (TJ) ........................ –40°C to +125°C
Thermal Resistance, SOT-23-5 (θJA) ........................ Note 3
Electrical Characteristics(4)
VIN = VOUT + 1V; IL = 100µA; CL = 1.0µF; VEN ≥ 2.0V; TJ = 25°C, bold values indicate –40°C ≤ TJ ≤ +125°C; unless noted.
Symbol
Parameter
Condition
Min
Typ
VO
Output Voltage Accuracy
variations from specified VOUT
∆VO/∆T
Output Voltage Temperature
Coefficient
Note 4
∆VO/VO
Line Regulation
VIN = VOUT + 1V to 16V
0.004
0.012
0.05
%/V
%/V
∆VO/VO
Load Regulation
IL = 0.1mA to 150mA, Note 5
0.02
0.2
0.5
%
%
VIN – VO
Dropout Voltage, Note 6
IL = 100µA
10
IL = 50mA
110
IL = 100mA
140
IL = 150mA
165
50
70
150
230
250
300
275
350
mV
mV
mV
mV
mV
mV
mV
mV
–1
–2
Max
Units
1
2
%
%
ppm/°C
40
IGND
Quiescent Current
VEN ≤ 0.4V (shutdown)
VEN ≤ 0.18V (shutdown)
0.01
1
5
µA
µA
IGND
Ground Pin Current, Note 7
VEN ≥ 2.0V, IL = 100µA
80
IL = 50mA
350
IL = 100mA
600
IL = 150mA
1300
125
150
600
800
1000
1500
1900
2500
µA
µA
µA
µA
µA
µA
µA
µA
500
mA
PSRR
Ripple Rejection
Frequency = 100Hz, IL = 100µA
75
ILIMIT
Current Limit
VOUT = 0V
320
∆VO/∆PD
Thermal Regulation
Note 8
0.05
eNO
Output Noise
IL = 50mA, CL = 2.2µF, 470pF from BYP to
GND
260
dB
%/W
nV/ Hz
ENABLE Input
VIL
Enable Input Logic-Low Voltage
regulator shutdown
VIH
Enable Input Logic-High
Voltage
regulator enabled
IIL
Enable Input Current
VIL ≤ 0.4V
VIL ≤ 0.18V
VIL = 2.0V
VIL = 2.0V
IIH
February 2006
0.4
0.18
2.0
V
0.01
2
3
V
V
5
–1
–2
20
25
µA
µA
µA
µA
M9999-020806
(408) 955-1690
Micrel
MIC5205
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. The maximum allowable power dissipation at any TA (ambient temperature) is PD(max) = (TJ(max) – TA) ⎟ ⎝JA. Exceeding the maximum allowable
power dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown. The ⎝JA of the MIC5205-xxBM5 (all
versions) is 220°C/W mounted on a PC board (see “Thermal Considerations” section for further details).
4. Output voltage temperature coefficient is defined as the worst case voltage change divided by the total temperature range.
5. Regulation is measured at constant junction temperature using low duty cycle pulse testing. Parts are tested for load regulation in the load range
from 0.1mA to 150mA. Changes in output voltage due to heating effects are covered by the thermal regulation specification.
6. Dropout Voltage is defined as the input to output differential at which the output voltage drops 2% below its nominal value measured at 1V
differential.
7. Ground pin current is the regulator quiescent current plus pass transistor base current. The total current drawn from the supply is the sum of the load
current plus the ground pin current.
8, Thermal regulation is defined as the change in output voltage at a time “t” after a change in power dissipation is applied, excluding load or line
regulation effects. Specifications are for a 150mA load pulse at VIN = 16V for t = 10ms.
February 2006
4
M9999-020806
(408) 955-1690
Micrel
MIC5205
Typical Characteristics
February 2006
5
M9999-020806
(408) 955-1690
Micrel
MIC5205
Typical Characteristics
February 2006
6
M9999-020806
(408) 955-1690
Micrel
MIC5205
Block Diagrams
Ultra-Low-Noise Fixed Regulator
Ultra-Low-Noise Adjustable Regulator
February 2006
7
M9999-020806
(408) 955-1690
Micrel
MIC5205
0.33µF for currents below 1mA.
Application Information
No-Load Stability
The MIC5205 will remain stable and in regulation with no
load (other than the internal voltage divider) unlike many
other voltage regulators. This is especially important in
CMOS RAM keep-alive applications.
Enable/Shutdown
Forcing EN (enable/shutdown) high (> 2V) enables the
regulator. EN is compatible with CMOS logic gates.
If the enable/shutdown feature is not required, connect
EN (pin 3) to IN (supply input, pin 1). See Figure 1.
Thermal Considerations
The MIC5205 is designed to provide 150mA of
continuous current in a very small package. Maximum
power dissipation can be calculated based on the output
current and the voltage drop across the part. To
determine the maximum power dissipation of the
package, use the junction-to-ambient thermal resistance
of the device and the following basic equation:
Input Capacitor
A 1µF capacitor should be placed from IN to GND if
there is more than 10 inches of wire between the input
and the ac filter capacitor or if a battery is used as the
input.
Reference Bypass Capacitor
BYP (reference bypass) is connected to the internal
voltage reference. A 470pF capacitor (CBYP) connected
from BYP to GND quiets this reference, providing a
significant reduction in output noise. CBYP reduces the
regulator phase margin; when using CBYP, output
capacitors of 2.2µF or greater are generally required to
maintain stability.
The start-up speed of the MIC5205 is inversely
proportional to the size of the reference bypass
capacitor. Applications requiring a slow ramp-up of
output voltage should consider larger values of CBYP.
Likewise, if rapid turn-on is necessary, consider omitting
CBYP.
If output noise is not a major concern, omit CBYP and
leave BYP open.
PD(max) =
θ JA
TJ(max) is the maximum junction temperature of the die,
125°C, and TA is the ambient operating temperature. θJA
is layout dependent; Table 1 shows examples of
junction-toambient thermal resistance for the MIC5205.
Package
θJA
θJA Square
Recommended
Copper Clad
Minimum
Footprint
SOT-23-5(M5)
220°C/W
170°C/W
Table 1. SOT-23-5 Thermal Resistance
θJC
130°C/W
The actual power dissipation of the regulator circuit can
be determined using the equation:
PD = (VIN – VOUT) IOUT + VIN IGND
Substituting PD(max) for PD and solving for the operating
conditions that are critical to the application will give the
maximum operating conditions for the regulator circuit.
For example, when operating the MIC5205-3.3BM5 at
room temperature with a minimum footprint layout, the
maximum input voltage for a set output current can be
determined as follows:
Output Capacitor
An output capacitor is required between OUT and GND
to prevent oscillation. The minimum size of the output
capacitor is dependent upon whether a reference bypass
capacitor is used. 1.0µF minimum is recommended
when CBYP is not used (see Figure 2). 2.2µF minimum is
recommended when CBYP is 470pF (see Figure 1).
Larger values improve the regulator’s transient
response. The output capacitor value may be increased
without limit.
The output capacitor should have an ESR (effective
series resistance) of about 5Ω or less and a resonant
frequency above 1MHz. Ultra-low-ESR capacitors can
cause a low amplitude oscillation on the output and/or
underdamped transient response. Most tantalum or
aluminum electrolytic capacitors are adequate; film types
will work, but are more expensive. Since many aluminum
electrolytics have electrolytes that freeze at about –
30°C, solid tantalums are recommended for operation
below –25°C.
At lower values of output current, less output
capacitance is required for output stability. The capacitor
can be reduced to 0.47⎧F for current below 10mA or
February 2006
(TJ(max) − TA )
PD(max) =
(125°C − 25°C)
220°C/W
PD(max) = 455mW
The junction-to-ambient thermal resistance for the
minimum footprint is 220°C/W, from Table 1. The
maximum power dissipation must not be exceeded for
proper operation. Using the output voltage of 3.3V and
an output current of 150mA, the maximum input voltage
can be determined. From the Electrical Characteristics
table, the maximum ground current for 150mA output
current is 2500µA or 2.5mA.
455mW = (VIN – 3.3V) 150mA + VIN·2.5mA
455mW = VIN×150mA – 495mW + VIN·2.5mA
950mW = VIN×152.5mA
8
M9999-020806
(408) 955-1690
Micrel
MIC5205
resistors set the output voltage based on the following
equation:
VIN(max) = 6.23V
Therefore, a 3.3V application at 150mA of output current
can accept a maximum input voltage of 6.2V in a SOT23-5 package. For a full discussion of heat sinking and
thermal effects on voltage regulators, refer to the
Regulator Thermals section of Micrel’s Designing with
Low-Dropout Voltage Regulators handbook.
⎛ R2
⎞
VOUT = 1.242V × ⎜
+ 1⎟
⎝ R1
⎠
This equation is correct due to the configuration of the
bandgap reference. The bandgap voltage is relative to
the output, as seen in the block diagram. Traditional
regulators normally have the reference voltage relative
to ground and have a different VOUT equation.
Resistor values are not critical because ADJ (adjust) has
a high input impedance, but for best results use resistors
of 470kΩ or less. A capacitor from ADJ to ground
provides greatly improved noise performance.
Fixed Regulator Applications
Figure 1. Ultra-Low-Noise Fixed Voltage Application
Figure 1 includes a 470pF capacitor for low-noise
operation and shows EN (pin 3) connected to IN (pin 1)
for an application where enable/shutdown is not
required. COUT = 2.2µF minimum.
Figure 3. Ultra-Low-Noise
Adjustable Voltage Application
Figure 3 includes the optional 470pF noise bypass
capacitor from ADJ to GND to reduce output noise.
Figure 2. Low-Noise Fixed Voltage Application
Dual-Supply Operation
When used in dual supply systems where the regulator
load is returned to a negative supply, the output voltage
must be diode clamped to ground.
Figure 2 is an example of a low-noise configuration
where CBYP is not required. COUT = 1µF minimum.
Adjustable Regulator Applications
The MIC5205BM5 can be adjusted to a specific output
voltage by using two external resistors (Figure 3). The
February 2006
9
M9999-020806
(408) 955-1690
Micrel
MIC5205
Package Information
SOT-23-5 (M5)
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http:/www.micrel.com
The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its
use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product
can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant
into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A
Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully
indemnify Micrel for any damages resulting from such use or sale.
© 2004 Micrel, Incorporated.
February 2006
10
M9999-020806
(408) 955-1690
Similar pages