LT6107 High Temperature High Side Current Sense Amp in SOT-23 FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ DESCRIPTION Fully Tested at –55°C, 25°C and 150°C Gain Configurable with Two Resistors Low Offset Voltage: 250μV Maximum Output Current: 1mA Maximum Supply Range: 2.7V to 36V, 44V Absolute Maximum Low Input Bias Current: 40nA Maximum PSRR: 106dB Minimum Low Supply Current: 65μA Typical, V+ = 12V Low Profile (1mm) ThinSOTTM Package APPLICATIONS ■ ■ ■ ■ ■ ■ Current Shunt Measurement Battery Monitoring Power Management Motor Control Lamp Monitoring Overcurrent and Fault Detection , LT, LTC and LTM are registered trademarks of Linear Technology Corporation. ThinSOT is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. The LT®6107 is a versatile high side current sense amplifier designed for operation over a wide temperature range. Design flexibility is provided by the excellent device characteristics: 250μV maximum offset and 40nA maximum input bias current. Gain for each device is set by two resistors and allows for accuracy better than 1%. The LT6107 monitors current via the voltage across an external sense resistor (shunt resistor). Internal circuitry converts input voltage to output current, allowing for a small sense signal on a high common mode voltage to be translated into a ground referenced signal. The low DC offset allows for monitoring very small sense voltages. As a result, a small valued shunt resistor can be used, which minimizes the power loss in the shunt. The wide 2.7V to 44V input voltage range, high accuracy and wide operating temperature range make the LT6107 ideal for automotive, industrial and power management applications. The very low power supply current of the LT6107 also makes it suitable for low power and battery operated applications. For applications not requiring the wide temperature range, see the LT6106. TYPICAL APPLICATION 3V to 36V, 5A Current Sense with AV = 10 Measurement Accuracy vs Load Current 3V TO 36V 0.6 ACCURACY (% OF FULL SCALE) 0.4 100Ω 0.02Ω +IN –IN + – LOAD V– V+ 0.2 0 TYPICAL PART, TA = 25°C –0.2 –0.4 –0.6 5A FULL SCALE RSENSE = 0.02 ROUT = 1k AV = 10 RIN = 100 V+ = 3V –0.8 –1.0 LT6107 OUT VOUT 200mV/A 1k –1.2 0 1 3 2 LOAD CURRENT (A) 4 5 6107 TA01b 6107 TA01a 6107fb 1 LT6107 ABSOLUTE MAXIMUM RATINGS PIN CONFIGURATION (Note 1) Supply Voltage (V+ to V–)..........................................44V Input Voltage (+IN to V–) ............................................ V+ (–IN to V–) ............................................ V+ Input Current........................................................–10mA Output Short-Circuit Duration .......................... Indefinite Operating Temperature Range (Note 2) ............................................. –55°C to 150°C Specified Temperature Range (Note 2) ............................................. –55°C to 150°C Storage Temperature Range................... –65°C to 150°C Lead Temperature (Soldering, 10 sec) .................. 300°C TOP VIEW 5 V+ OUT 1 V– 2 4 +IN –IN 3 S5 PACKAGE 5-LEAD PLASTIC TSOT-23 TJMAX = 150°C, θJA = 250°C/W ORDER INFORMATION Lead Free Finish TAPE AND REEL (MINI) TAPE AND REEL PART MARKING PACKAGE DESCRIPTION TEMPERATURE RANGE LT6107MPS5#TRMPBF LT6107MPS5#TRPBF LTDGZ 5-Lead Plastic TSOT-23 –55°C to 150°C Lead Based Finish TAPE AND REEL (MINI) TAPE AND REEL PART MARKING PACKAGE DESCRIPTION LT6107MPS5#TRM LT6107MPS5#TR LTDGZ 5-Lead Plastic TSOT-23 TRM = 500 pieces. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ TEMPERATURE RANGE –55°C to 150°C ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full specified operating temperature range, otherwise specifications are at TA = 25°C. V+ = 12V, V+ = VSENSE+, RIN = 100Ω, ROUT = 10k, Gain = 100 unless otherwise noted. (Note 6) SYMBOL PARAMETER V+ Supply Voltage Range VOS Input Offset Voltage ΔVOS/ΔT Input Offset Voltage Drift VSENSE = 5mV IB Input Bias Current (+IN) V+ = 12V, 36V IOS Input Offset Current V+ = 12V, 36V IOUT Maximum Output Current (Note 3) Power Supply Rejection Ratio V+ = 2.7V to 36V, V PSRR CONDITIONS MIN ● VSENSE = 5mV TYP 2.7 150 ● ● MAX V 250 400 μV μV 1 μV/°C 40 130 ● 1 SENSE = 5mV UNITS 36 nA nA nA ● 1 mA ● 106 dB VSENSE(MAX) Input Sense Voltage Full Scale RIN = 500Ω (Notes 3, 7) ● 0.5 AV Error Gain Error (Note 4) VSENSE = 500mV, RIN = 500Ω, ROUT = 10k, V+ = 12.5V ● –0.65 –0.25 0 % VSENSE = 500mV, RIN = 500Ω, ROUT = 10k, V+ = 36V ● –0.45 –0.14 0.1 % 1.2 1.4 V V VOUT(HIGH) Output Swing High (Referred to V+) VSENSE = 120mV ● V 6107fb 2 LT6107 ELECTRICAL CHARACTERISTICS The ● denotes the specifications which apply over the full specified operating temperature range, otherwise specifications are at TA = 25°C. V+ = 12V, V+ = VSENSE+, RIN = 100Ω, ROUT = 10k, Gain = 100 unless otherwise noted. (Note 6) SYMBOL PARAMETER CONDITIONS MIN Minimum Output Voltage (Note 5) VSENSE = 0mV, RIN = 100Ω, ROUT = 10k MAX 12 45 85 mV mV 7 16 40 mV mV ● VSENSE = 0mV, RIN = 500Ω, ROUT = 10k, V+ = 12V, 36V BW Signal Bandwidth (–3dB) tr Input Step Response (to 50% of ΔVSENSE = 100mV Step, RIN = 100Ω, ROUT = 5k, Output Step) Rising Edge IS Supply Current ● IOUT = 1mA, RIN = 100Ω, ROUT = 5k V+ = 2.7V, IOUT = 0μA, (VSENSE = –5mV) kHz 3.5 μs 60 85 120 μA 65 95 125 μA 70 100 135 μA ● V+ = 36V, IOUT = 0μA, (VSENSE = –5mV) UNITS 200 ● V+ = 12V, IOUT = 0μA, (VSENSE = –5mV) Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. In addition to the Absolute Maximum Ratings, the output current of the LT6107 must be limited to insure that the power dissipation in the LT6107 does not allow the die temperature to exceed 150°C. See the applications information section “Power Dissipation Considerations” for further information. Note 2: Junction temperatures greater than 125°C will promote accelerated aging. The LT6107 has demonstrated typical life beyond 1000 hours at 150°C. TYP ● Note 3: Guaranteed by the gain error test. Note 4: Gain error refers to the contribution of the LT6107 internal circuitry and does not include errors in the external gain setting resistors. Note 5: The LT6107 output is an open collector current source. The minimum output voltage scales directly with the ratio ROUT/10k. Note 6: VSENSE+ is the voltage at the high side of the sense resistor, RSENSE. See Figure 1. Note 7: VSENSE(MAX) is the maximum sense voltage for which the Electrical Characteristics will apply. Higher voltages can affect performance but will not damage the part provided that the output current of the LT6107 does not exceed the allowable power dissipation as described in Note 1. TYPICAL PERFORMANCE CHARACTERISTICS 12 10 8 6 4 2 0 –200 –120 120 –40 0 40 INPUT OFFSET VOLTAGE (μV) 200 6107 G23 70 60 50 40 30 20 10 0 –10 –20 –30 –40 –50 –60 –70 600 VSENSE = 5mV RIN = 100Ω ROUT = 10k TYPICAL UNITS 500 INPUT OFFSET VOLTAGE (μV) PERCENT OF UNITS (%) 14 V+ = 12V VSENSE = 5mV RIN = 100Ω ROUT = 10k 1068 UNITS CHANGE IN INPUT OFFSET VOLTAGE (μV) 16 Input Offset Voltage vs Temperature Input Offset Voltage vs Supply Voltage VOS Distribution 400 300 200 VSENSE = 5mV V+ = 12V RIN = 100Ω ROUT = 10k AV = 100 TYPICAL UNITS 100 0 –100 –200 –300 0 5 10 15 20 25 30 SUPPLY VOLTAGE (V) 35 40 6107 G02 –400 –55 –35 –15 5 25 45 65 85 105 125 145 165 TEMPERATURE (°C) 6107 G03 6107fb 3 LT6107 TYPICAL PERFORMANCE CHARACTERISTICS Power Supply Rejection Ratio vs Frequency 120 –0.05 V+ = 36V GAIN ERROR (%) –0.10 –0.15 V+ = 12V –0.20 V+ = 5V –0.25 V+ = 2.7V –0.30 –0.35 VOUT = 1V –0.40 IOUT = 1mA ROUT = 1k –0.45 –60 –40 –20 0 20 40 60 80 100 120 140 160 180 TEMPERATURE (°C) POWER SUPPLY REJECTION RATIO (dB) 0.00 V+ = 12.5V AV = 20 RIN = 100Ω ROUT = 2k 110 100 90 80 70 60 50 40 30 20 10 0 100 VOUT = 0.5V VOUT = 1V VOUT = 2V 1k 10k 100k FREQUENCY (Hz) Gain Error Distribution 16 14 12 10 8 6 4 2 0 –0.60 –0.48 –0.36 –0.24 GAIN ERROR (%) –0.12 0 45 40 35 30 25 20 15 10 5 0 –5 –10 –15 –20 –25 –30 VOUT = 10V VOUT = 2.5V 1k INPUT BIAS CURRENT (nA) 70 60 50 40 30 20 10 10 15 20 25 30 35 40 45 50 SUPPLY VOLTAGE (V) 1k 10k 100k FREQUENCY (Hz) 10k 1M Gain vs Frequency AV = 100 RIN = 100Ω ROUT = 10k 100k 1M FREQUENCY (Hz) 10M VOUT = 10V V+ = 12.5V AV = 20 RIN = 500Ω ROUT = 10k VOUT = 2.5V 1k 10k 100k 1M FREQUENCY (Hz) 10M 6107 G14 Step Response 10mV to 20mV (RIN = 100Ω) VSENSE 20mV/DIV TA = –55°C TA = –40°C TA = 25°C TA = 70°C TA = 125°C TA = 150°C TA = 175°C VOUT = 2.5V VOUT = 5V VOUT = 10V 45 40 35 30 25 20 15 10 5 0 –5 –10 –15 –20 –25 –30 Step Response 0mV to 10mV (RIN = 100Ω) VSENSE = 5mV RIN = 100Ω 5 80 6107 G09 Input Bias Current vs Supply Voltage 0 90 6107 G06 V+ = 12.5V 6107 G24 300 280 260 240 220 200 180 160 140 120 100 80 60 40 20 0 100 0 100 1M GAIN (dB) PERCENT OF UNITS (%) 18 GAIN (dB) VSENSE = 500mV RIN = 500Ω ROUT = 10k 11,072 UNITS TA = 25°C 20 V+ = 12.5V AV = 20 RIN = 500Ω ROUT = 10k 110 Gain vs Frequency V+ = 12.5V 22 120 6107 G08 6107 G04 24 Power Supply Rejection Ratio vs Frequency POWER SUPPLY REJECTION RATIO (dB) Gain Error vs Temperature VSENSE 20mV/DIV VOUT 500mV/DIV VOUT 500mV/DIV 0V 0V AV = 100 VOUT = 0V TO 1V ROUT = 10k V+ = 12V 5μs/DIV 6107 G10 AV = 100 VOUT = 1V TO 2V ROUT = 10k V+ = 12V 5μs/DIV 6107 G11 6107 G05 6107fb 4 LT6107 TYPICAL PERFORMANCE CHARACTERISTICS Step Response 0mV to 100mV (RIN = 100Ω) Step Response 10mV to 100mV (RIN = 100Ω) Step Response 50mV to 100mV (RIN = 500Ω) VSENSE 200mV/DIV VSENSE 200mV/DIV VSENSE 100mV/DIV VOUT 2V/DIV VOUT 2V/DIV VOUT 500mV/DIV 0V 0V 0V 6107 G12 AV = 100 5μs/DIV VOUT = 0V TO 10V ROUT = 10k V+ = 12V 6107 G13 AV = 100 5μs/DIV VOUT = 1V TO 10V ROUT = 10k V+ = 12V Step Response 0mV to 50mV (RIN = 500Ω) AV = 20 VOUT = 1V TO 2V ROUT = 10k V+ = 12V Step Response 50mV to 500mV (RIN = 500Ω) VSENSE 100mV/DIV 6107 G15 5μs/DIV Step Response 0mV to 500mV (RIN = 500Ω) VSENSE 1V/DIV VSENSE 1V/DIV VOUT 2V/DIV VOUT 2V/DIV 0V 0V VOUT 500mV/DIV 0V 5μs/DIV 6107 G16 11.05 900 800 11.00 10.95 10.90 10.85 10.80 –60 –40 –20 0 20 40 60 80 100 120 140 160 180 TEMPERATURE (°C) 6107 G07 Output Voltage vs Input Sense Voltage (0mV ≤ VSENSE ≤ 10mV) 220 V+ = 12V AV = 100 RIN = 100Ω ROUT = 10k 1000 VOUT (mV) OUTPUT VOLTAGE (V) 11.10 1100 V+ = 12V AV = 100 RIN = 100Ω ROUT = 10k VSENSE = 120mV 180 160 600 500 140 120 100 400 80 300 60 200 40 100 20 0 1 2 V+ = 12V AV = 20 RIN = 500Ω ROUT = 10k 200 700 0 3 4 5 6 7 VSENSE (mV) 8 9 6107 G18 AV = 20 5μs/DIV VOUT = 0V TO 10V ROUT = 10k V+ = 12V Output Voltage vs Input Sense Voltage (0mV ≤ VSENSE ≤ 10mV) Output Voltage Swing vs Temperature 11.15 6107 G17 AV = 20 5μs/DIV VOUT = 1V TO 10V ROUT = 10k V+ = 12V VOUT (mV) AV = 20 VOUT = 0V TO 1V ROUT = 10k V+ = 12V 10 6107 G19 0 0 1 2 3 4 5 6 7 VSENSE (mV) 8 9 10 6107 G20 6107fb 5 LT6107 TYPICAL PERFORMANCE CHARACTERISTICS Output Voltage vs Input Sense Voltage (0mV ≤ VSENSE ≤ 1V) 12 12 V+ = 12V AV = 100 RIN = 100Ω ROUT = 10k 10 10 AV = 20 RIN = 500Ω ROUT = 10k 100 8 VOUT (V) VOUT (V) 8 Supply Current vs Supply Voltage 120 V+ = 12V SUPPLY CURRENT (μA) Output Voltage vs Input Sense Voltage (0mV ≤ VSENSE ≤ 200mV) 6 6 4 4 2 2 0 20 40 60 80 100 120 140 160 180 200 VSENSE (mV) 60 TA = –55°C TA = –40°C TA = 25°C TA = 70°C TA = 125°C TA = 150°C TA = 175°C 40 20 0 0 80 0 0 100 200 300 400 500 600 700 800 900 1000 VSENSE (mV) 6107 G21 0 5 10 15 20 25 30 35 SUPPLY VOLTAGE (V) 6107 G22 40 45 6107 G01 PIN FUNCTIONS V+ (Pin 5): Positive Supply Pin. The V+ pin should be connected directly to either side of the sense resistor, RSENSE. Supply current is drawn through this pin. The circuit may be configured so that the LT6107 supply current is or is not monitored along with the system load current. To monitor only the system load current, connect V+ to the more positive side of the sense resistor. To monitor the total current, including that of the LT6107, connect V+ to the more negative side of the sense resistor. OUT (Pin 1): Current Output. OUT will source a current that is proportional to the sense voltage into an external resistor. V– (Pin 2): Normally Connected to Ground. –IN (Pin 3): The internal sense amplifier will drive –IN to the same potential as +IN. A resistor (RIN) tied from V+ to –IN sets the output current IOUT = VSENSE /RIN. VSENSE is the voltage developed across RSENSE. +IN (Pin 4): Must be tied to the system load end of the sense resistor, either directly or through a resistor. BLOCK DIAGRAM ILOAD – VSENSE + VBATTERY RSENSE L O A D 5 RIN V+ 3 4 –IN 14k – +IN 14k + IOUT V– 2 OUT VOUT = VSENSE • 1 6107 F01 ROUT RIN ROUT Figure 1. LT6107 Block Diagram and Typical Connection 6107fb 6 LT6107 APPLICATIONS INFORMATION Introduction The LT6107 high side current sense amplifier (Figure 1) provides accurate monitoring of current through a user-selected sense resistor. The sense voltage is amplified by a userselected gain and level shifted from the positive power supply to a ground-referred output. The output signal is analog and may be used as is, or processed with an output filter. Theory of Operation An internal sense amplifier loop forces –IN to have the same potential as +IN. Connecting an external resistor, RIN, between –IN and V+ forces a potential across RIN that is the same as the sense voltage across RSENSE. A corresponding current, VSENSE /RIN, will flow through RIN. The high impedance inputs of the sense amplifier will not conduct this current, so it will flow through an internal PNP to the output pin as IOUT. The output current can be transformed into a voltage by adding a resistor from OUT to V–. The output voltage is then VO = V– + IOUT • ROUT. Table 1. Useful Gain Configurations GAIN 20 50 100 GAIN 20 50 100 RIN 499Ω 200Ω 100Ω RIN 249Ω 100Ω 50Ω ROUT 10k 10k 10k ROUT 5k 5k 5k VSENSE at VOUT = 5V 250mV 100mV 50mV VSENSE at VOUT = 125mV 50mV 25mV IOUT at VOUT = 5V 500μA 500μA 500μA IOUT at VOUT = 2.5V 500μA 500μA 500μA must be small enough that VSENSE does not exceed the maximum input voltage specified by the LT6107, even under peak load conditions. As an example, an application may require that the maximum sense voltage be 100mV. If this application is expected to draw 2A at peak load, RSENSE should be no more than 50mΩ. Once the maximum RSENSE value is determined, the minimum sense resistor value will be set by the resolution or dynamic range required. The minimum signal that can be accurately represented by this sense amplifier is limited by the input offset. As an example, the LT6107 has a typical input offset of 150μV. If the minimum current is 20mA, a sense resistor of 7.5mΩ will set VSENSE to 150μV. This is the same value as the input offset. A larger sense resistor will reduce the error due to offset by increasing the sense voltage for a given load current. Choosing a 50mΩ RSENSE will maximize the dynamic range and provide a system that has 100mV across the sense resistor at peak load (2A), while input offset causes an error equivalent to only 3mA of load current. Peak dissipation is 200mW. If a 5mΩ sense resistor is employed, then the effective current error is 30mA, while the peak sense voltage is reduced to 10mV at 2A, dissipating only 20mW. The low offset and corresponding large dynamic range of the LT6107 make it more flexible than other solutions in this respect. The 150μV typical offset gives 60dB of dynamic range for a sense voltage that is limited to 150mV maximum, and over 70dB of dynamic range if the rated input maximum of 0.5V is allowed. Selection of External Current Sense Resistor Sense Resistor Connection The external sense resistor, RSENSE, has a significant effect on the function of a current sensing system and must be chosen with care. Kelvin connection of the –IN and +IN inputs to the sense resistor should be used in all but the lowest power applications. Solder connections and PC board interconnections that carry high current can cause significant error in measurement due to their relatively large resistances. One 10mm × 10mm square trace of one-ounce copper is approximately 0.5mΩ. A 1mV error can be caused by as little as 2A flowing through this small interconnect. This will cause a 1% error in a 100mV signal. A 10A load current in the same interconnect will cause a 5% error for the same 100mV signal. By isolating the sense traces from the high current paths, this error can be reduced First, the power dissipation in the resistor should be considered. The system load current will cause both heat and voltage loss in RSENSE. As a result, the sense resistor should be as small as possible while still providing the input dynamic range required by the measurement. Note that input dynamic range is the difference between the maximum input signal and the minimum accurately measured signal, and is limited primarily by input DC offset of the internal amplifier of the LT6107. In addition, RSENSE 6107fb 7 LT6107 APPLICATIONS INFORMATION by orders of magnitude. A sense resistor with integrated Kelvin sense terminals will give the best results. Figure 2 illustrates the recommended method. + V RSENSE RIN +IN This approach can be helpful in cases where occasional bursts of high currents can be ignored. Care should be taken when designing the board layout for RIN, especially for small RIN values. All trace and interconnect resistances will increase the effective RIN value, causing a gain error. –IN + Selection of External Output Resistor, ROUT – LOAD V– V+ The output resistor, ROUT, determines how the output current is converted to voltage. VOUT is simply IOUT • ROUT. OUT LT6107 VOUT ROUT 6107 F02 Figure 2. Kelvin Input Connection Preserves Accuracy with Large Load Currents Selection of External Input Resistor, RIN RIN should be chosen to allow the required resolution while limiting the output current to 1mA. In addition, the maximum value for RIN is 500Ω. By setting RIN such that the largest expected sense voltage gives IOUT = 1mA, then the maximum output dynamic range is available. Output dynamic range is limited by both the maximum allowed output current and the maximum allowed output voltage, as well as the minimum practical output signal. If less dynamic range is required, then RIN can be increased accordingly, reducing the maximum output current and power dissipation. If low sense currents must be resolved accurately in a system that has a very wide dynamic range, a smaller RIN than the maximum current spec allows may be used if the maximum current is limited in another way, such as with a Schottky diode across RSENSE (Figure 3). This will reduce the high current measurement accuracy by limiting the result, while increasing the low current measurement resolution. In choosing an output resistor, the maximum output voltage must first be considered. If the following circuit is a buffer or ADC with limited input range, then ROUT must be chosen so that IOUT(MAX) • ROUT is less than the allowed maximum input range of this circuit. In addition, the output impedance is determined by ROUT. If the circuit to be driven has high enough input impedance, then almost any useful output impedance will be acceptable. However, if the driven circuit has relatively low input impedance, or draws spikes of current such as an ADC might do, then a lower ROUT value may be required in order to preserve the accuracy of the output. As an example, if the input impedance of the driven circuit is 100 times ROUT, then the accuracy of VOUT will be reduced by 1% since: VOUT = IOUT • ROUT • RIN(DRIVEN) ROUT + RIN(DRIVEN) = IOUT • ROUT • 100 = 0.99 • IOUT • ROUT 101 Error Sources The current sense system uses an amplifier and resistors to apply gain and level shift the result. The output is then dependent on the characteristics of the amplifier, such as gain and input offset, as well as resistor matching. Ideally, the circuit output is: V+ RSENSE DSENSE VOUT = VSENSE • ROUT ; VSENSE = RSENSE • ISENSE RIN 6107 F03 LOAD Figure 3. Shunt Diode Limits Maximum Input Voltage to Allow Better Low Input Resolution Without Overranging In this case, the only error is due to resistor mismatch, which provides an error in gain only. However, offset voltage and bias current cause additional errors. 6107fb 8 LT6107 APPLICATIONS INFORMATION V+ Output Error Due to the Amplifier DC Offset Voltage, VOS R EOUT( VOS) = VOS • OUT RIN The DC offset voltage of the amplifier adds directly to the value of the sense voltage, VSENSE. This is the dominant error of the system and it limits the low end of the dynamic range. The paragraph “Selection of External Current Sense Resistor” provides details. RSENSE RIN– RIN+ +IN –IN + – LOAD V– V+ LT6107 OUT VOUT ROUT RIN+ = RIN– – RSENSE 6107 F04 Output Error Due to the Bias Currents, IB+ and IB– Figure 4. Second Input R Minimizes Error Due to Input Bias Current The bias current IB+ flows into the positive input of the internal op amp. IB – flows into the negative input. Minimum Output Voltage R EOUT(IBIAS) = ROUT IB + • SENSE – IB – RIN Assuming IB+ ≅ IB – = IBIAS, and RSENSE << RIN then: EOUT(IBIAS) ≅ –ROUT • IBIAS It is convenient to refer the error to the input: EIN(IBIAS) ≅ –RIN • IBIAS For instance if IBIAS is 60nA and RIN is 1k, the input referred error is 60μV. Note that in applications where RSENSE ≅ RIN, IB+ causes a voltage offset in RSENSE that cancels the error due to IB– and EOUT(IBIAS) ≅ 0mV. In most applications, RSENSE << RIN, the bias current error can be similarly reduced if an external resistor RIN+ = (RIN – RSENSE) is connected as shown in Figure 4. Under both conditions: EIN(IBIAS) = ±RIN • IOS; where IOS = IB+ – IB – If the offset current, IOS, of the LT6107 amplifier is 6nA, the 60μV error above is reduced to 6μV. Adding RIN+ as described will maximize the dynamic range of the circuit. For less sensitive designs, RIN+ is not necessary. Output Error Due to Gain Error The LT6107 exhibits a typical gain error of –0.25% at 1mA output current. The primary source of gain error is due to the finite gain to the PNP output transistor, which results in a small percentage of the current in RIN not appearing in the output load ROUT. The curves of the Output Voltage vs Input Sense Voltage show the behavior of the LT6107 with low input sense voltages. When VSENSE = 0V, the output voltage will always be slightly positive, the result of input offset voltages and of a small amount of quiescent current (0.7μA to 1.2μA) flowing through the output device. The minimum output voltage in the Electrical Characteristics table include both these effects. Power Dissipation Considerations The power dissipated by the LT6107 will cause a small increase in the die temperature. This rise in junction temperature can be calculated if the output current and the supply current are known. The power dissipated in the LT6107 due to the output signal is: POUT = (V–IN – VOUT) • IOUT Since V–IN ≅ V+, POUT ≅ (V+ – VOUT) • IOUT The power dissipated due to the quiescent supply current is: PQ = IS • (V+ – V–) The total power dissipated is the output dissipation plus the quiescent dissipation: PTOTAL = POUT + PQ The junction temperature is given by: TJ = TA + θJA • PTOTAL At the maximum operating supply voltage of 36V and the maximum guaranteed output current of 1mA, the total 6107fb 9 LT6107 APPLICATIONS INFORMATION power dissipation is 41mW. This amount of power dissipation will result in a 10°C rise in junction temperature above the ambient temperature. It is important to note that the LT6107 has been designed to provide at least 1mA to the output when required, and can deliver more depending on the conditions. Care must be taken to limit the maximum output current by proper choice of sense resistor and RIN – and, if input fault conditions exist, external clamps. Output Filtering The output voltage, VOUT, is simply IOUT • ZOUT. This makes filtering straightforward. Any circuit may be used which generates the required ZOUT to get the desired filter response. For example, a capacitor in parallel with ROUT will give a lowpass response. This will reduce unwanted noise from the output, and may also be useful as a charge reservoir to keep the output steady while driving a switching circuit such as a MUX or ADC. This output capacitor in parallel with an output resistor will create a pole in the output response at: f–3dB = normal operation, VSENSE should not exceed 500mV (see VSENSE(MAX) under Electrical Characteristics). This additional constraint can be stated as V+ – (+IN) ≤ 500mV. Referring to Figure 5, feedback will force the voltages at the inputs –IN and +IN to be equal to (VS – VSENSE). Connecting V+ to the load side of the shunt results in equal voltages at +IN, –IN and V+. Connecting V+ to the supply end of the shunt results in the voltages at +IN and –IN to be VSENSE below V+. If the V+ pin is connected to the supply side of the shunt resistor, the supply current drawn by the LT6107 is not included in the monitored current. If the V+ pin is connected to the load side of the shunt resistor (Figure 5), the supply current drawn by the LT6107 is included in the monitored current. It should be noted that in either configuration, the output current of the LT6107 will not be monitored since it is drawn through the RIN resistor connected to the positive side of the shunt. Contact the factory for operation of the LT6107 with a V+ outside of the recommended operating range. VS RIN 1 RSENSE 2 • π • ROUT • COUT +IN –IN + LOAD Useful Equations V– – V+ Input Voltage: VSENSE = ISENSE • RSENSE Voltage Gain: VOUT R = OUT VSENSE RIN LT6107 OUT VOUT ROUT 6107 F05 Current Gain: IOUT ISENSE Transconductance: Transimpedance: = RSENSE RIN Figure 5. LT6107 Supply Current Monitored with the Load Reverse Supply Protection IOUT 1 = VSENSE RIN VOUT ISENSE = RSENSE • ROUT RIN Power Supply Connection For normal operation, the V+ pin should be connected to either side of the sense resistor. Either connection will meet the constraint that +IN ≤ V+ and –IN ≤ V+. During Some applications may be tested with reverse-polarity supplies due to an expectation of the type of fault during operation. The LT6107 is not protected internally from external reversal of supply polarity. To prevent damage that may occur during this condition, a Schottky diode should be added in series with V– (Figure 6). This will limit the reverse current through the LT6107. Note that this diode will limit the low voltage performance of the LT6107 by effectively reducing the supply voltage to the part by VD. 6107fb 10 LT6107 APPLICATIONS INFORMATION In addition, if the output of the LT6107 is wired to a device that will effectively short it to high voltage (such as through an ESD protection clamp) during a reverse supply condition, the LT6107’s output should be connected through a resistor or Schottky diode (Figure 7). Response Time The photos in the Typical Performance Characteristics show the response of the LT6107 to a variety of input conditions and values of RIN. The photos show that if the output current is very low or zero and an input transient occurs, there will be an increased delay before the output voltage begins changing while internal nodes are being charged. Demo Board Demo board DC1240 is available for evaluation of the LT6107. RSENSE RSENSE +IN –IN + – V– L O A D +IN R1 100Ω V– L O A D V+ VBATT D1 + – LT6107 OUT LT6107 R1 100Ω –IN VBATT V+ OUT R3 1k ADC R2 4.99k D1 R2 4.99k 6107 F07 6107 F06 Figure 7. Additional Resistor R3 Protects Output During Supply Reversal Figure 6. Schottky Diode Prevents Damage During Supply Reversal PACKAGE DESCRIPTION S5 Package 5-Lead Plastic TSOT-23 (Reference LTC DWG # 05-08-1635) 0.62 MAX 0.95 REF 2.90 BSC (NOTE 4) 1.22 REF 1.4 MIN 3.85 MAX 2.62 REF 2.80 BSC 1.50 – 1.75 (NOTE 4) PIN ONE RECOMMENDED SOLDER PAD LAYOUT PER IPC CALCULATOR 0.30 – 0.45 TYP 5 PLCS (NOTE 3) 0.95 BSC 0.80 – 0.90 0.20 BSC 0.01 – 0.10 1.00 MAX DATUM ‘A’ 0.30 – 0.50 REF NOTE: 1. DIMENSIONS ARE IN MILLIMETERS 2. DRAWING NOT TO SCALE 3. DIMENSIONS ARE INCLUSIVE OF PLATING 0.09 – 0.20 (NOTE 3) 1.90 BSC S5 TSOT-23 0302 REV B 4. DIMENSIONS ARE EXCLUSIVE OF MOLD FLASH AND METAL BURR 5. MOLD FLASH SHALL NOT EXCEED 0.254mm 6. JEDEC PACKAGE REFERENCE IS MO-193 6107fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11 LT6107 TYPICAL APPLICATION Simple 400V Current Monitor DANGER! Lethal Potentials Present — Use Caution ISENSE VSENSE – 400V + RSENSE +IN L O A D V– –IN + – RIN 100Ω DANGER!! HIGH VOLTAGE!! V+ OUT LT6107 12V CMPZ12L M1 VOUT M1 AND M2 ARE FQD3P50 ROUT VOUT = • VSENSE = 49.9 VSENSE RIN M2 ROUT 4.99k BAT46 2M 6107 TA02 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1787 Precision Bidirectional, High Side Current Sense Amplifier 75μV VOS, 60V, 60μA Operation LT6100 Gain-Selectable High Side Current Sense Amplifier 4.1V to 48V, Pin-Selectable Gain: 10, 12.5, 20, 25, 40, 50V/V ® LTC 6101/LTC6101HV High Voltage, High Side, Precision Current Sense Amplifiers 4V to 60V/5V to 100V, Gain Configurable, SOT-23 LTC6102/LTC6102HV Zero Drift High Side Current Sense Amplifier 4V to 60V/5V to 100V Operation, 10μV Offset, 1μs Step Response, MSOP8/DFN LTC6103 Dual High Side, Precision Current Sense Amplifier 4V to 60V, Gain Configurable 8-Pin MSOP LTC6104 Bidirectional High Side, Precision Current Sense Amplifier 4V to 60V, Gain Configurable 8-Pin MSOP LT6105 Rail-to-Rail Input Precision High Side Current Sense Amplifier –0.3V to 44V Input Common Mode Range, 300μV Offset, 1% Gain Accuracy, Gain Configurable LT6106 Low Cost, High Side Precision Current Sense Amplifier 2.7V to 36V, Gain Configurable, SOT-23 6107fb 12 Linear Technology Corporation LT 0808 REV B • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com © LINEAR TECHNOLOGY CORPORATION 2008