256M GDDR SDRAM K4D553238F-JC 256Mbit GDDR SDRAM 2M x 32Bit x 4 Banks Graphic Double Data Rate Synchronous DRAM with Bi-directional Data Strobe and DLL (144-Ball FBGA) Revision 1.0 March 2004 Samsung Electronics reserves the right to change products or specification without notice. - 1 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC Revision History Revision 1.0 (March 8, 2004) • DC Specification finalized Revision 0.1 (March 2 , 2004) - Target Spec Revision 0.0 (October 28, 2003) - Target Spec • Defined Target Specification - 2 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC 2M x 32Bit x 4 Banks Graphic Double Data Rate Synchronous DRAM with Bi-directional Data Strobe and DLL FEATURES • 2.5V + 5% power supply for device operation • 4 DQS’s ( 1DQS / Byte ) • 2.5V + 5% power supply for I/O interface • Data I/O transactions on both edges of Data strobe • SSTL_2 compatible inputs/outputs • DLL aligns DQ and DQS transitions with Clock transition • 4 banks operation • Edge aligned data & data strobe output • MRS cycle with address key programs • Center aligned data & data strobe input -. Read latency 3, 4 (clock) • DM for write masking only -. Burst length (2, 4 and 8) • Auto & Self refresh -. Burst type (sequential & interleave) • 32ms refresh period (4K cycle) • All inputs except data & DM are sampled at the positive going edge of the system clock • 144-Ball FBGA • Maximum clock frequency up to 350MHz • Differential clock input • Maximum data rate up to 700Mbps/pin • No Wrtie-Interrupted by Read Function ORDERING INFORMATION Part NO. Max Freq. Max Data Rate K4D553238F-JC2A 350MHz 700Mbps/pin K4D553238F-JC33 300MHz 600Mbps/pin K4D553238F-JC36 275MHz 550Mbps/pin K4D553238F-JC40 250MHz 500Mbps/pin K4D553238F-JC50 200MHz 400Mbps/pin Interface Package SSTL_2 144-Ball FBGA 1. K4D553238F-EC is the Lead Free package part number 2. For the K4D553238F-JC2A, VDD & VDDQ =2.8V + 0.1V GENERAL DESCRIPTION FOR 2M x 32Bit x 4 Bank GDDR SDRAM The K4D553238F is 268,435,456 bits of hyper synchronous data rate Dynamic RAM organized as 4 x 2,097,152 words by 32 bits, fabricated with SAMSUNG’s high performance CMOS technology. Synchronous features with Data Strobe allow extremely high performance up to 2.8GB/s/chip. I/O transactions are possible on both edges of the clock cycle. Range of operating frequencies, programmable burst length and programmable latencies allow the device to be useful for a variety of high performance memory system applications. - 3 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC PIN CONFIGURATION (Top View) 2 3 4 5 6 7 8 9 10 11 12 13 B DQS0 DM0 VSSQ DQ3 DQ2 DQ0 DQ31 DQ29 DQ28 VSSQ DM3 DQS3 C DQ4 VDDQ NC VDDQ DQ1 VDDQ VDDQ DQ30 VDDQ NC VDDQ DQ27 D DQ6 DQ5 VSSQ VSSQ VSSQ VDD VDD VSSQ VSSQ VSSQ DQ26 DQ25 E DQ7 VDDQ VDD VSS VSSQ VSS VSS VSSQ VSS VDD VDDQ DQ24 F DQ17 DQ16 VDDQ VSSQ VSS VSS Thermal Thermal VSS VSS Thermal Thermal VSSQ VDDQ DQ15 DQ14 G DQ19 DQ18 VDDQ VSSQ VSS VSS Thermal Thermal VSS VSS Thermal Thermal VSSQ VDDQ DQ13 DQ12 H DQS2 DM2 NC VSSQ VSS VSS Thermal Thermal VSS VSS Thermal Thermal VSSQ NC DM1 DQS1 J DQ21 DQ20 VDDQ VSSQ VSS VSS Thermal Thermal VSS VSS Thermal Thermal VSSQ VDDQ DQ11 DQ10 K DQ22 DQ23 VDDQ VSSQ VSS VSS VSS VSS VSSQ VDDQ DQ9 DQ8 L CAS WE VDD VSS A10 VDD VDD RFU1 VSS VDD NC NC M RAS NC NC BA1 A2 A11 A9 A5 RFU2 CK CK MCL N CS NC BA0 A0 A1 A3 A4 A6 A7 A8/AP CKE VREF NOTE: 1. RFU1 is reserved for A12 2. RFU2 is reserved for BA2 3. VSS Thermal balls are optional PIN DESCRIPTION CK,CK Differential Clock Input BA0, BA1 Bank Select Address CKE Clock Enable A0 ~A11 Address Input CS Chip Select DQ0 ~ DQ31 Data Input/Output RAS Row Address Strobe VDD Power CAS Column Address Strobe VSS Ground WE Write Enable VDDQ Power for DQ’s DQS Data Strobe VSSQ Ground for DQ’s DM Data Mask NC No Connection RFU Reserved for Future Use MCL Must Connect Low - 4 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC INPUT/OUTPUT FUNCTIONAL DESCRIPTION Symbol Type Function CK, CK*1 Input The differential system clock Input. All of the inputs are sampled on the rising edge of the clock except DQ’s and DM’s that are sampled on both edges of the DQS. CKE Input Activates the CK signal when high and deactivates the CK signal when low. By deactivating the clock, CKE low indicates the Power down mode or Self refresh mode. CS Input CS enables the command decoder when low and disabled the command decoder when high. When the command decoder is disabled, new commands are ignored but previous operations continue. RAS Input Latches row addresses on the positive going edge of the CK with RAS low. Enables row access & precharge. CAS Input Latches column addresses on the positive going edge of the CK with CAS low. Enables column access. WE Input Enables write operation and row precharge. Latches data in starting from CAS, WE active. Input/Output Data input and output are synchronized with both edge of DQS. DQS0 for DQ0 ~ DQ7, DQS1 for DQ8 ~ DQ15, DQS2 for DQ16 ~ DQ23, DQS3 for DQ24 ~ DQ31. DM0 ~ DM3 Input Data In mask. Data In is masked by DM Latency=0 when DM is high in burst write. DM0 for DQ0 ~ DQ7, DM1 for DQ8 ~ DQ15, DM2 for DQ16 ~ DQ23, DM3 for DQ24 ~ DQ31. DQ0 ~ DQ31 Input/Output Data inputs/Outputs are multiplexed on the same pins. BA0, BA1 Input Selects which bank is to be active. A0 ~ A11 Input Row/Column addresses are multiplexed on the same pins. Row addresses : RA0 ~ RA11, Column addresses : CA0 ~ CA7,CA9 Column address CA8 is used for auto precharge. VDD/VSS Power Supply Power and ground for the input buffers and core logic. VDDQ/VSSQ Power Supply Isolated power supply and ground for the output buffers to provide improved noise immunity. VREF Power Supply Reference voltage for inputs, used for SSTL interface. No connection/ Reserved for future use This pin is recommended to be left "No connection" on the device Must Connect Low Must connect low DQS0 ~ DQS3 NC/RFU MCL *1 : The timing reference point for the differential clocking is the cross point of CK and CK. For any applications using the single ended clocking, apply VREF to CK pin. - 5 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC BLOCK DIAGRAM (2Mbit x 32I/O x 4 Bank) 32 Intput Buffer I/O Control CK, CK Data Input Register Serial to parallel Bank Select LWE LDMi 64 2Mx32 32 Output Buffer 2Mx32 64 2-bit prefetch Sense AMP Row Decoder Refresh Counter Row Buffer ADDR Address Register CK,CK 2Mx32 x32 DQi 2Mx32 Column Decoder Col. Buffer LCBR LRAS Latency & Burst Length LRAS LCBR Strobe Gen. Programming Register LCKE Data Strobe (DQS0~DQS3) DLL LWE LCAS LWCBR CK,CK LDMi Timing Register CK,CK CKE CS RAS CAS WE - 6 - DMi Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC FUNCTIONAL DESCRIPTION • Power-Up Sequence GDDR SDRAMs must be powered up and initialized in a predefined manner to prevent undefined operations. 1. Apply power and keep CKE at low state (All other inputs may be undefined) - Apply VDD before VDDQ . - Apply VDDQ before VREF & VTT 2. Start clock and maintain stable condition for minimum 200us. 3. The minimum of 200us after stable power and clock(CK,CK ), apply NOP and take CKE to be high . 4. Issue precharge command for all banks of the device. 5. Issue a EMRS command to enable DLL *1 6. Issue a MRS command to reset DLL. The additional 200 clock cycles are required to lock the DLL. *1,2 7. Issue precharge command for all banks of the device. 8. Issue at least 2 or more auto-refresh commands. 9. Issue a mode register set command with A8 to low to initialize the mode register. *1 The additional 200cycles of clock input is required to lock the DLL after enabling DLL. *2 Sequence of 6&7 is regardless of the order. Power up & Initialization Sequence 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 ~ precharge ALL Banks EMRS MRS DLL Reset 1st Auto Refresh precharge ALL Banks ~ tRP tRFC tRFC 200 Clock min. Inputs must be stable for 200us 2nd Auto Refresh ~ ~ ~ 2 Clock min. 2 Clock min. Mode Register Set Any Command ~ ~ 2 Clock min. ~ ~ ~ tRP Command ~ ~ CK,CK * When the operating frequency is changed, DLL reset should be required again. After DLL reset again, the minimum 200 cycles of clock input is needed to lock the DLL. - 7 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC MODE REGISTER SET(MRS) The mode register stores the data for controlling the various operating modes of GDDR SDRAM. It programs CAS latency, addressing mode, burst length, test mode, DLL reset and various vendor specific options to make GDDR SDRAM useful for variety of different applications. The default value of the mode register is not defined, therefore the mode register must be written after EMRS setting for proper operation. The mode register is written by asserting low on CS, RAS, CAS and WE(The GDDR SDRAM should be in active mode with CKE already high prior to writing into the mode register). The state of address pins A0 ~ A11 and BA0, BA1 in the same cycle as CS, RAS, CAS and WE going low is written in the mode register. Minimum two clock cycles are requested to complete the write operation in the mode register. The mode register contents can be changed using the same command and clock cycle requirements during operation as long as all banks are in the idle state. The mode register is divided into various fields depending on functionality. The burst length uses A0 ~ A2, addressing mode uses A3, CAS latency(read latency from column address) uses A4 ~ A6. A7 is used for test mode. A8 is used for DLL reset. A7,A8, BA0 and BA1 must be set to low for normal MRS operation. Refer to the table for specific codes for various burst length, addressing modes and CAS latencies. BA1 BA0 RFU 0 A11 A10 A9 RFU DLL A8 A8 A7 DLL TM A6 A5 A3 CAS Latency A2 BT A1 A0 Burst Length Address Bus Mode Register Burst Type Test Mode DLL Reset A4 A7 mode A3 Type 0 No 0 Normal 0 Sequential 1 Yes 1 Test 1 Interleave 0 Burst Length CAS Latency BA0 A1 A0 Sequential Interleave Reserved 0 0 0 Reserve Reserve Reserved 0 0 1 2 2 1 0 4 4 A6 A5 A4 Latency 0 MRS 0 0 0 1 EMRS 0 0 1 * RFU(Reserved for future use) should stay "0" during MRS cycle. Burst Type A2 An ~ A0 0 1 0 Reserved 0 0 1 1 3 0 1 1 8 8 1 0 0 4 1 0 0 Reserve Reserve 1 0 1 Reserved 1 0 1 Reserve Reserve 1 1 0 Reserved 1 1 0 Reserve Reserve Reserved 1 1 1 Reserve Reserve 1 1 1 MRS Cycle 0 1 2 3 4 5 6 7 8 CK, CK Command NOP Precharge All Banks NOP NOP MRS NOP Any Command NOP NOP tMRD=2 tCK tRP *1 : MRS can be issued only at all banks precharge state. *2 : Minimum tRP is required to issue MRS command. - 8 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC EXTENDED MODE REGISTER SET(EMRS) The extended mode register stores the data for enabling or disabling DLL and selecting output driver strength. The default value of the extended mode register is not defined, therefore the extened mode register must be written after power up for enabling or disabling DLL. The extended mode register is written by asserting low on CS, RAS, CAS, WE and high on BA0(The GDDR SDRAM should be in all bank precharge with CKE already high prior to writing into the extended mode register). The state of address pins A0, A2 ~ A5, A7 ~ A11 and BA1 in the same cycle as CS, RAS, CAS and WE going low are written in the extended mode register. A1 and A6 are used for setting driver strength to normal, weak or matched impedance. Two clock cycles are required to complete the write operation in the extended mode register. The mode register contents can be changed using the same command and clock cycle requirements during operation as long as all banks are in the idle state. A0 is used for DLL enable or disable. "High" on BA0 is used for EMRS. All the other address pins except A0,A1,A6 and BA0 must be set to low for proper EMRS operation. Refer to the table for specific codes. BA1 BA0 RFU 1 BA0 A11 A10 A9 A8 A7 RFU A6 A5 A4 D.I.C An ~ A0 A6 A1 0 MRS 0 1 1 EMRS 1 A3 A2 RFU Output Driver Impedence Control 1 A1 A0 D.I.C DLL A0 Address Bus Extended Mode Register DLL Enable Weak 0 Enable Matched 1 Disable *1 : RFU(Reserved for future use) should stay "0" during EMRS cycle. Figure 7. Extended Mode Register set - 9 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC ABSOLUTE MAXIMUM RATINGS Parameter Symbol Value Unit VIN, VOUT -0.5 ~ 3.6 V Voltage on VDD supply relative to Vss VDD -1.0 ~ 3.6 V Voltage on VDD supply relative to Vss VDDQ -0.5 ~ 3.6 V Storage temperature TSTG -55 ~ +150 °C Power dissipation PD 2.0 W Short circuit current IOS 50 mA Voltage on any pin relative to Vss Note : Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. POWER & DC OPERATING CONDITIONS(SSTL_2 In/Out) Recommended operating conditions(Voltage referenced to VSS=0V, TA=0 to 65°C) Parameter Symbol Min Typ Max Unit Note Device Supply voltage VDD 2.375 2.5 2.625 V 1, 7 Output Supply voltage VDDQ 2.375 2.5 2.625 V 1, 7 Reference voltage VREF 0.49*VDDQ - 0.51*VDDQ V 2 Termination voltage Vtt VREF-0.04 VREF VREF+0.04 V 3 Input logic high voltage VIH(DC) VREF+0.15 - VDDQ+0.30 V 4 Input logic low voltage VIL(DC) -0.30 - VREF-0.15 V 5 Output logic high voltage VOH Vtt+0.76 - - V IOH=-15.2mA Output logic low voltage VOL - - Vtt-0.76 V IOL=+15.2mA Input leakage current IIL -5 - 5 uA 6 Output leakage current IOL -5 - 5 uA 6 Note : 1. Under all conditions VDDQ must be less than or equal to VDD. 2. VREF is expected to equal 0.50*VDDQ of the transmitting device and to track variations in the DC level of the same. Peak to peak noise on the VREF may not exceed + 2% of the DC value. 3. Vtt of the transmitting device must track VREF of the receiving device. 4. VIH(max.)= VDDQ +1.5V for a pulse width and it can not be greater than 1/3 of the cycle rate. 5. VIL(mim.)= -1.5V for a pulse width and it can not be greater than 1/3 of the cycle rate. 6. For any pin under test input of 0V < VIN < VDD is acceptable. For all other pins that are not under test VIN=0V. 7. For the K4D553238F-JC2A, VDD & VDDQ = 2.8V + 0.1V - 10 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC DC CHARACTERISTICS Recommended operating conditions Unless Otherwise Noted, TA=0 to 65°C) Version Parameter Symbol Test Condition Unit Note -2A -33 -36 -40 -50 340 320 300 280 Operating Current (One Bank Active) ICC1 Burst Lenth=2 tRC ≥ tRC(min) IOL=0mA, tCC= tCC(min) 400 Precharge Standby Current in Power-down mode ICC2P CKE ≤ VIL(max), tCC= tCC(min) 120 Precharge Standby Current in Non Power-down mode ICC2N Active Standby Current power-down mode ICC3P Active Standby Current in in Non Power-down mode ICC3N CKE ≥ VIH(min), CS ≥ VIH(min), tCC= tCC(min) CKE ≤ VIL(max), tCC= tCC(min) CKE ≥ VIH(min), CS ≥ VIH(min), tCC= tCC(min) mA 90 mA 190 150 140 130 120 mA 170 130 120 110 100 mA 250 220 210 200 190 mA Operating Current ( Burst Mode) ICC4 IOL=0mA ,tCC= tCC(min), Page Burst, All Banks activated. 650 550 520 460 430 mA Refresh Current ICC5 tRC ≥ tRFC(min) 470 415 395 365 335 mA Self Refresh Current ICC6 CKE ≤ 0.2V Operating Current (4Bank interleaving) ICC7 Burst Length=4 tRC ≥ tRC(min) IOL=0mA, tCC= tCC(min) 8 840 6 680 630 1 2 mA 590 550 mA Note : 1. Measured with outputs open. 2. Refresh period is 32ms. AC INPUT OPERATING CONDITIONS Recommended operating conditions(Voltage referenced to VSS=0V, VDD=2.5V+ 5%, VDDQ=2.5V+ 5%,TA=0 to 65°C) Parameter Symbol Min Typ Max Unit Note Input High (Logic 1) Voltage; DQ VIH VREF+0.35 - - V Input Low (Logic 0) Voltage; DQ VIL - - VREF-0.35 V Clock Input Differential Voltage; CK and CK VID 0.7 - VDDQ+0.6 V 1 Clock Input Crossing Point Voltage; CK and CK VIX 0.5*VDDQ-0.2 - 0.5*VDDQ+0.2 V 2 Note : 1. VID is the magnitude of the difference between the input level on CK and the input level on CK 2. The value of VIX is expected to equal 0.5*VDDQ of the transmitting device and must track variations in the DC level of the same - 11 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC AC OPERATING TEST CONDITIONS (VDD=2.5V±5%, TA= 0 to 65°C) Parameter Value Unit Input reference voltage for CK(for single ended) 0.50*VDDQ V 1.5 V CK and CK signal maximum peak swing CK signal minimum slew rate Input Levels(VIH/VIL) 1.0 V/ns VREF+0.35/VREF-0.35 V VREF V Vtt V Input timing measurement reference level Output timing measurement reference level Output load condition Note See Fig.1 Vtt=0.5*VDDQ RT=50Ω Output Z0=50Ω VREF =0.5*VDDQ CLOAD=30pF (Fig. 1) Output Load Circuit CAPACITANCE (VDD=2.5V, TA= 25°C, f=1MHz) Parameter Symbol Min Max Unit Input capacitance( CK, CK ) CIN1 5.0 10.0 pF Input capacitance(A0~A11, BA0~BA1) CIN2 5.0 9.0 pF Input capacitance ( CKE, CS, RAS,CAS, WE ) CIN3 5.0 9.0 pF Data & DQS input/output capacitance(DQ0~DQ31) COUT 4.0 8.0 pF Input capacitance(DM0 ~ DM3) CIN4 4.0 8.0 pF DECOUPLING CAPACITANCE GUIDE LINE Recommended decoupling capacitance added to power line at board. Symbol Value Unit Decoupling Capacitance between VDD and VSS Parameter CDC1 0.1 + 0.01 uF Decoupling Capacitance between VDDQ and VSSQ CDC2 0.1 + 0.01 uF Note : 1. VDD and VDDQ pins are separated each other. All VDD pins are connected in chip. All VDDQ pins are connected in chip. 2. VSS and VSSQ pins are separated each other All VSS pins are connected in chip. All VSSQ pins are connected in chip. - 12 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC AC CHARACTERISTICS Symbol Parameter CL=3 CL=4 CK cycle time tCK DQ and DM hold time to DQS tCH tCL tDQSCK tAC tDQSQ tRPRE tRPST tDQSS tWPRES tWPREH tWPST tDQSH tDQSL tIS tIH tDS tDH Clock half period tHP CK high level width CK low level width DQS out access time from CK Output access time from CK Data strobe edge to Dout edge Read preamble Read postamble CK to valid DQS-in DQS-In setup time DQS-in hold time DQS write postamble DQS-In high level width DQS-In low level width Address and Control input setup Address and Control input hold DQ and DM setup time to DQS Data output hold time from DQS tQH -2A -33 Min 2.86 0.45 Max 0.55 Min 3.3 0.45 0.45 0.55 0.45 -0.6 0.6 -0.6 -36 -40 Max 0.55 Min 3.6 0.45 0.55 0.45 -0.6 0.6 0.6 -0.6 - 0.35 0.9 1.1 10 Max 0.55 Min 4.0 0.45 0.55 0.45 -0.6 0.6 0.6 -0.6 - 0.35 0.9 1.1 10 -50 Unit Max 0.55 Min 5.0 0.45 0.55 ns ns tCK 0.55 0.45 0.55 tCK -0.6 0.6 -0.7 0.7 ns 0.6 -0.6 0.6 -0.7 0.7 ns - 0.40 - 0.40 - 0.45 ns 0.9 1.1 0.9 1.1 0.9 1.1 tCK 10 Max 10 10 0.4 0.6 0.4 0.6 0.4 0.6 0.4 0.6 0.4 0.6 tCK 0.85 1.15 0.85 1.15 0.85 1.15 0.85 1.15 0.8 1.2 tCK Note 1 0 - 0 - 0 - 0 - 0 - ns 0.35 - 0.35 - 0.35 - 0.35 - 0.3 - tCK 0.4 0.6 0.4 0.6 0.4 0.6 0.4 0.6 0.4 0.6 tCK 0.4 0.6 0.4 0.6 0.4 0.6 0.4 0.6 0.4 0.6 tCK 0.4 0.6 0.4 0.6 0.4 0.6 0.4 0.6 0.4 0.6 tCK 0.9 - 0.9 - 0.9 - 0.9 - 1.0 - ns 0.9 - 0.9 - 0.9 - 0.9 - 1.0 - ns 0.35 - 0.35 - 0.40 - 0.40 - 0.45 - ns 0.35 tCLmin or tCHmin tHP -0.35 - 0.35 tCLmin or tCHmin tHP -0.35 - 0.40 tCLmin or tCHmin tHP -0.4 - 0.40 tCLmin or tCHmin tHP -0.4 - 0.45 tCLmin or tCHmin tHP0.45 - ns - ns 1 - ns 1 - - - - Simplified Timing @ BL=2, CL=4 tCH tCL tCK 0 1 2 3 5 4 6 8 7 CK, CK tIS CS tIH tDQSCK tDQSS DQS tRPST tRPRE tWPRES tDQSQ tDQSH tDQSL tWPREH tDS tDH tAC DQ Qa1 Db0 Qa2 Db1 DM WRITEB COMMAND READA - 13 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC Note 1 : - The JEDEC GDDR specification currently defines the output data valid window(tDV) as the time period when the data strobe and all data associated with that data strobe are coincidentally valid. - The previously used definition of tDV(=0.35tCK) artificially penalizes system timing budgets by assuming the worst case output vaild window even then the clock duty cycle applied to the device is better than 45/55% - A new AC timing term, tQH which stands for data output hold time from DQS is difined to account for clock duty cycle variation and replaces tDV - tQHmin = tHP-X where . tHP=Minimum half clock period for any given cycle and is defined by clock high or clock low time(tCH,tCL) . X=A frequency dependent timing allowance account for tDQSQmax tQH Timing (CL4, BL2) tHP 0 1 3 2 4 5 CK, CK CS DQS tDQSQ(max) tQH tDQSQ(max) Qa0 DQ COMMAND Qa1 READA - 14 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC AC CHARACTERISTICS (I) Parameter -2A Symbol -33 -36 -40 -50 Unit Note Min Max Min Max Min Max Min Max Min Max tRC tRFC tRAS tRCDRD tRCDW 16 - 16 - 16 - 13 - 12 - 17 - 17 - 17 - 15 - 14 - tCK 11 100K 11 100K 11 100K 9 100K 8 100K tCK 5 - 5 - 4 - 4 - 4 - tCK 3 - 3 - 2 - 2 - 2 - tCK tRP tRRD 5 - 5 - 5 - 4 - 4 - tCK 3 - 3 - 3 - 3 - 3 - tCK tWR 4 - 4 - 4 - 3 - 3 - tCK 1 tWR_A 4 - 4 - 4 - 3 - 3 - tCK 1 tCDLR tCCD tMRD 3 - 3 - 2 - 2 - 2 - tCK 1 1 - 1 - 1 - 1 - 1 - tCK 2 - 2 - 2 - 2 - 2 - tCK tDAL 9 - 9 - 9 - 7 - 7 - tCK tXSR 200 - 200 - 200 - 200 - 200 - tCK Power down exit time tPDEX 3tCK +tIS - 3tCK +tIS - 3tCK +tIS - 3tCK +tIS - 3tCK +tIS - ns Refresh interval time tREF 7.8 - 7.8 - 7.8 - 7.8 - 7.8 - us Row cycle time Refresh row cycle time Row active time RAS to CAS delay for Read RAS to CAS delay for Write Row precharge time Row active to Row active Last data in to Row precharge @Normal Precharge Last data in to Row precharge @Auto Precharge Last data in to Read command Col. address to Col. address Mode register set cycle time Auto precharge write recovery + Precharge Exit self refresh to read command tCK Note : 1. For normal write operation, even numbers of Din are to be written inside DRAM (Unit : Number of Clock) AC CHARACTERISTICS (II) (Unit : Number of Clock) K4D553238F-JC2A Frequency Cas Latency 350MHz ( 2.86ns ) 4 300MHz ( 3.3ns ) 4 275MHz ( 3.6ns ) 4 250MHz ( 4.0ns ) 3 200MHz ( 5.0ns ) 3 tRC 16 16 16 13 12 tRFC 17 17 17 15 14 tRAS 11 11 11 9 8 tRCDRD tRCDWR 5 3 5 3 4 2 4 2 4 2 tRP 5 5 5 4 4 tRRD 3 3 3 3 3 tDAL 9 9 9 7 7 Unit K4D553238F-JC33 Frequency Cas Latency 300MHz ( 3.3ns ) 4 275MHz ( 3.6ns ) 4 250MHz ( 4.0ns ) 3 200MHz ( 5.0ns ) 3 tRC 16 16 13 12 tRFC 17 17 15 14 tRAS 11 11 9 8 tRCDRD tRCDWR 5 3 4 2 4 2 4 2 tRP 5 5 4 4 tRRD 3 3 3 3 tDAL 9 9 7 7 Unit - 15 - tCK tCK tCK tCK tCK tCK tCK tCK tCK Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC K4D553238F-JC36 Frequency Cas Latency 275MHz ( 3.6ns ) 4 250MHz ( 4.0ns ) 3 200MHz ( 5.0ns ) 3 tRC 16 13 12 tRFC 17 15 14 tRAS 11 9 8 tRCDRD tRCDWR 4 2 4 2 4 2 tRP 5 4 4 tRRD 3 3 3 tDAL 9 7 7 Unit K4D553238F-JC40 Frequency Cas Latency 250MHz ( 4.0ns ) 3 200MHz ( 5.0ns ) 3 tRC 13 12 tRFC 15 14 tRAS 9 8 tRCDRD tRCDWR 4 2 4 2 tRP 4 4 tRRD 3 3 tDAL 7 7 Unit K4D553238F-JC50 Frequency Cas Latency 200MHz ( 5.0ns ) 3 tRC 12 tRFC 14 tRAS 8 tRCDRD tRCDWR 4 2 tRP 4 tRRD 3 tDAL 7 Unit tCK tCK tCK tCK tCK tCK Simplified Timing(2) @ BL=4 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 BAa BAb BAa BAb Ra Rb Ra Rb Ca Cb 17 18 19 20 21 22 CK, CK BA[1:0] BAa BAa BAa Ra A8/AP Ra ADDR (A0~A7, Ra A9,A10) Ca WE DQS DQ Da0 Da1 Da2 Da3 Db0 Db1 Db2 Db3 Da0 Da1 Da2 Da3 DM COMMAND ACTIVEA PRECH WRITEA ACTIVEA ACTIVEB WRITEA WRITEB tRCD tRAS tRP tRC Normal Write Burst (@ BL=4) tRRD Multi Bank Interleaving Write Burst (@ BL=4) - 16 - Rev 1.0 (Mar. 2004) 256M GDDR SDRAM K4D553238F-JC PACKAGE DIMENSIONS (144-Ball FBGA) A1 INDEX MARK 12.0 12.0 <Top View> 0.8x11=8.8 A1 INDEX MARK 0.10 Max 0.8 B C D E F G H J K L M N 0.40 0.8x11=8.8 0.45 ± 0.05 0.8 13 12 11 10 9 8 7 6 5 4 3 2 0.35 ± 0.05 0.40 1.40 Max <Bottom View> Unit : mm - 17 - Rev 1.0 (Mar. 2004)