POWER Data Sheet ADN-C Series 3-Phase 120-960 Watts Total Power: 120-960 Watts Input Voltage: 380-480 Vac # Outputs: Single SPECIAL FEATURES Slim form factor Five year warranty High efficiency up to 94% Full power at 60 °C Power Boost™ Industrial grade design • Metal case MTBF > 500,000h Adjustable output Overvoltage protection with auto recovery Continuous short circuit and overload protection New visual diagnostic LED Three Status LEDs • Input • Output • Alarm DC OK relay Parallel operation capability Screw terminal connections RoHS compliant No tools required for mounting SAFETY UL508, cULus Listed UL 60950-1, cURus 2nd edition IEC60950-1 2nd edition Class I, Div 2 Hazardous Locations IP20 CE Electrical Specifications Input Nominal voltage 380 - 480 Vac AC input range 320 - 540 Vac DC input range 450 - 760 Vdc for ADN5, ADN10 & ADN20 Frequency 50 - 60 Hz Efficiency Up to 94% PFC Active power factor correction for ADN20 & ADN40; meet EN61000-3-2 Class A Phase input ADN5 and ADN10 will operate with single phase input at 100% load Derate to 75% and 50% for ADN20 and ADN40 respectively under loss of 1 phase; Units will shut down if thermal threshold is exceeded under this condition Output Nominal voltage 24 V (24.0 - 28.0 Vdc Adj.) Hold-up time > 20 ms for ADN5, ADN10 & ADN20; > 15 ms for ADN40 Voltage regulation < ± 2% overall Ripple < 100 mVpp Current limit PowerBoost™ Peak current 2x nominal current for < 2 sec for ADN5 & ADN10; 1.5x nominal current for 4 seconds minimum while holding voltage > 20 Vdc for ADN20 & ADN40 Parallel operation Single or parallel operation selectable via front switch. For redundant operation use of external diode module is preferred; ADN40 uses active paralleling Power back immunity < 35 V Overvoltage protection > 30.5 Vdc, but < 33 Vdc, auto recovery ADN-C Series 3-Phase Data Sheet General Specifications EMC emissions EN61000-6-3:2001, Class B EN55011, EN55022 Radiated and Conducted including Annex. A, EN61000-3-2 EMC immunity EN61000-6-1:2001, EN61000-6-2:2001, EN61000-4-2 Level 4, EN61000-4-3 Level 3, EN61000-4-6 Level 3, EN61000-4-4 Level 4 input and level 3 output. EN61000-4-5 Isolation class 4, EN61000-4-11, Semi F47 sag immunity Warranty 5 Years General protection safety Protected against continuous short-circuit, overload, open-circuit. Protection Class 1 (IEC536), degree of protection IP20 (IEC 60529) Safe low voltage: SELV (acc. EN60950) Status indicators Visual: 3 status LEDs (Input, Output, Alarm) Relay: SSR or dry relay contact, signal octive when Vout = 18.5 vdc + 5% LED Diagnostics LED OK Loss of Ac Low Ac No Dc High Load Overload Hot Too Hot Input Green --- Yellow Green Green Green Green Green Output Green --- Green --- Yellow Yellow Green --- Alarm --- --- --- Red Yellow Red Yellow Yellow Environmental Specifications Storage/shipment -40 °C to + 85 °C Operation (convection) Full Load -25 °C to + 60 °C derate to 50% load at +70 °C Up to 50% load permissable with horizontal or on top mounting orientation Humidity < 90% RH, non-condensingl IEC 60068-2-2, 68-2-3 Other Features Fusing Input externally fused; output not fused, output is capable of providing high currents (PowerBoost) for motor load startup Mounting orientation Standard: Vertical, Optional: Horizontal or on Top Simple snap-on to DIN TS35/7.5 or TS35/15 rail system Ventilation Normal convection, No fan required Cooling spacing ADN5: 15 mm in front, 25 mm above and below ADN10: 15 mm in front, 25 mm above and below ADN20: 25 mm in front, left and right; 70 mm above and below ADN40: 15 mm in front, 70 mm above and below, 25 mm left and rightt Connections Input: Screw terminals, connector size range: 16-10 AWG (1.5-6 mm2) for solid conductors Output: Connector size range: 16-10 AWG (1.5-6 mm2) for ADN5, ADN10 and ADN20 solid conductors; 6-7 AWG for ADN40 ADN-C Series 3-Phase Data Sheet Ordering Information Model Number Power ADN5-24-3PM-C 120 W ADN10-24-3PM-C 240 W ADN20-24-3PM-C 480 W ADN40-24-3PM-C 960 W Current Efficiency 1.15 lbs (520 g) 5 A @ 24 Vdc 85.0% 1.54 lbs (700 g) 10 A @ 24 Vdc 91.2% 2.8 lbs (1300 g) 20 A @ 24 Vdc 93.0% 5.3 lbs (2400 g) 40 A @ 24 Vdc 94.0% Input Voltage Weight 320 - 540 Vac 450 - 760 Vdc 320 - 540 Vac Case Type MTBF Metal > 500,000 hours Nominal voltage, full load, Tamb=25 oC Dimensions Height Width Depth ADN5-24-3PM-C 4.85 in (123 mm) 1.97 in (50 mm) 4.36 (111 mm) ADN10-24-3PM-C 4.85 in (123 mm) 2.36 in (60 mm) 4.36 (111 mm) ADN20-24-3PM-C 4.85 in (123 mm) 3.34 in (85 mm) 4.68 (119 mm) ADN40-24-3PM-C 4.85 in (123 mm) 7.09 in (180 mm) 4.85 in (123 mm) Mechanical Drawing D W + - + - 24 VDC / 20 A OK Input Output Alarm 24 - 28 Vd c Single H Parallel ADN20-24-3PM-C U L C US LISTED 380 - 480 V3; 3W + PE 50/60 Hz 0.9 A / Phase L1 L2 L3 D W H ADN40-24-3PM-C Overload Output: 24 VDC / 40 A Electronically Protec ted 2428V + + - - OK Si ngle Use L1 L2 L3 Parallel Use Input: 3PH 380/500 VAC 1.7/1.5A/Phase 50/60 Hz Continuous Mode US LISTED Reset fuse mode U L Fuse Mode C WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2015 Artesyn Embedded Technologies, Inc. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] ADN-C Series 3-Phase DS 03Aug2015