CXOX/CXOXHG OSCILLATOR 1 MHz to 160 MHz Ultra-Miniature, High Stability High Shock Crystal Oscillator DESCRIPTION Statek’s ultra miniature and ultra low profile CXOX/CXOXHG oscillators consist of a CMOS/TTL compatible hybrid circuit and a state-of-the-art, miniature, fundamental-mode crystal. DIMENSIONS A FEATURES 4 High shock resistance (HG version) CMOS and TTL compatible 3 TOP Low power consumption 1 Full military testing available Low acceleration sensitivity (HG version) Optional Output Enable/Disable with Tri-State Low EMI emission Hermetically sealed ceramic package Designed and manufactured in the USA APPLICATIONS C 2 D B 2 TYPICAL E 4 3 BOTTOM 1 MAXIMUM DIM inches mm inches mm A 0.126 3.20 0.136 3.40 B 0.099 2.50 0.107 2.70 C (SM1) 0.039 C (SM3/SM5) 0.044 1.00 1.12 0.043 0.048 1.09 1.21 D 0.040 1.00 0.041 1.10 E 0.030 0.75 0.031 0.85 Military & Aerospace Smart munitions PIN CONNECTIONS Communications 1. Output Enable/Disable (E) or no connection (N) Navigation 2. Ground GPS 3. Output Industrial, Computer & Communications Miniature clock oscillator 4. VDD SUGGESTED LAND PATTERN Handheld instrumentation 0.141 (3.6) PDA Transponder/Animal migration Medical Test & diagnostic equipment 0.110 (2.9) 0.031 (0.8) Handheld devices 0.039 (1.05) 0.051 (1.3) 0.039 (1.0) inches (mm) IS O STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com 90 01 TEM C ERT I F I C AT N IO S 10168 Rev C YS SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS Specifications below are examples. Specifications are subject to change without notice. Tighter specifications available. Please contact factory. Supply Voltage VDD -0.5 V to 7.0 V Storage Temperature -55OC to 125OC Maximum Process Temperature 260OC for 20 seconds Frequency Range1 Supply Voltage 1 MHz to 160 MHz 1.8 V to 5.0 V ± 10% Calibration Tolerance2 ± 100 ppm Frequency Stability Over Temperature3 Supply Current (Typical) 24 MHz 32 MHz 50 MHz 130 MHz Output Load (CMOS)4 ENABLE/DISABLE OPTIONS (E/N) ± 50 ppm for Commercial ± 100 ppm for Industrial ± 100 ppm for Military 1.8 V 3.3 V 5.0 V 1.5 mA 3.0 mA 8.0 mA 2.0 mA 5.0 mA 10.0 mA 3.0 mA 6.0 mA 13.0 mA 12.0 mA 23.0 mA 39.0 mA ENABLE/DISABLE OPTION E FUNCTION TABLE 15 pF Start-up Time 5 ms MAX Rise/Fall Time 6 ns MAX Duty Cycle 40% MIN 60% MAX Aging, first year 5 ppm MAX Shock, survival6 5,000 g, 0.3 ms, 1/2 sine HG: 10,000 g, 0.3 ms, 1/2 sine` Vibration, survival7 20 g, 10-2,000 Hz swept sine 5 Statek offers two enable/disable options: E and N. The Eversion has a Tri-State output and stops oscillating internally when the output is put into the high Z state. The N-version does not have PIN 1 connected internally and so has no enable/disable capability. The following table describes the Enable/Disable option E. Enable (Pin 1 High*) Disable (Pin 1 Low) Output Frequency Output High Z State Oscillator Oscillates Stops Current Normal Very Low * When PIN 1 is allowed to float, it is held high by an internal pull-up resistor. Operating Temp. Range -10 C to 70 C (Commerical) -40OC to 85OC (Industrial) -55OC to 125OC (Military) O O PACKAGING OPTIONS 1. 2. 3. 4. 5. 6. 7. Not all frequencies available at all voltages. Contact factory. Tighter tolerances available. Does not include calibration tolerances. Tighter tolerances available. Higher CMOS loads and TTL loads available. Contact factory. 45/55 available upon request in most cases. Higher shock version available. Contact factory for requirements above 10,000 g Per MIL-STD-202G, Method 204D, Condition D. Random vibration testing also available. Note: All parameters are measured at ambient temperature with a 10 M1, 15 pF load. CXOX/ CXOXHG - Tray Pack - 12 mm tape, 7” or 13” reels Per EIA 481 (see Tape and Reel data sheet #10109) HOW TO ORDER CXOX/CXOXHG SURFACE MOUNT CRYSTAL OSCILLATORS CXOX HG = High Shock. Otherwise leave blank HG 4 Supply Voltage 1 = 1.8 V 2 = 2.5 V 3 = 3.0 V 4 = 3.3 V 5 = 5.0 V S N “S” if special or custom design. Blank if Std. Enable/Disable Option E or N SM3 Terminations Blank = SM1 = Gold Plated (Lead Free) SM3 = Solder Dipped SM5 = Solder Dipped (Lead Free) 40.0M , Frequency K = kHz M = MHz 100 / Calibration Tolerance @ 250C (in ppm) 100 / Frequency Stability over Temp. Range (in ppm) Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified OR / / I / 200 Total Frequency Tolerance (in ppm) / I Temp. Range: C = -10OC to +70OC I = -40OC to +85OC M = -55OC to +125OC S = Customer Specified IS O STATEK CORPORATION 512 N. MAIN ST., ORANGE, CA 92868 714-639-7810 FAX: 714-997-1256 www.statek.com 90 01 TEM C ERT I F I C AT N IO S 10168 Rev C YS