MC7900 Series 1.0 A Negative Voltage Regulators The MC7900 series of fixed output negative voltage regulators are intended as complements to the popular MC7800 series devices. These negative regulators are available in the same seven−voltage options as the MC7800 devices. In addition, one extra voltage option commonly employed in MECL systems is also available in the negative MC7900 series. Available in fixed output voltage options from − 5.0 V to − 24 V, these regulators employ current limiting, thermal shutdown, and safe−area compensation − making them remarkably rugged under most operating conditions. With adequate heatsinking they can deliver output currents in excess of 1.0 A. • No External Components Required • Internal Thermal Overload Protection • Internal Short Circuit Current Limiting • Output Transistor Safe−Area Compensation • Available in 2% Voltage Tolerance (See Ordering Information) • Pb−Free Package May be Available. The G−Suffix Denotes a Pb−Free Lead Finish http://onsemi.com TO−220 T SUFFIX CASE 221A Heatsink surface connected to Pin 2. 2 3 Pin 1. Ground 2. Input 3. Output D2PAK D2T SUFFIX CASE 936 2.0 k 14.7 k 8.0 k 3.6 k 4.0 k 4.0 k 1.0 k 1.0 k 12 k 1.2 k 1 2 3 Heatsink surface (shown as terminal 4 in case outline drawing) is connected to Pin 2. 25 2.4 k Gnd 2.0 k 1 R1 1.6 k STANDARD APPLICATION R2 MC79XX Input VO 10 k Cin* 0.33 F Output CO** 1.0 F 20 pF 10 pF 2.0 k 20 k 20 k 10 k 240 0.3 1.1 k 750 VI This device contains 26 active transistors. Figure 1. Representative Schematic Diagram A common ground is required between the input and the output voltages. The input voltage must remain typically 2.0 V above more negative even during the high point of the input ripple voltage. XX, These two digits of the type number indicate nominal voltage. ** Cin is required if regulator is located an appreciable distance from power supply filter. ** CO improve stability and transient response. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 11 of this data sheet. DEVICE MARKING INFORMATION See general marking information in the device marking section on page 14 of this data sheet. Semiconductor Components Industries, LLC, 2005 May, 2005 − Rev. 13 1 Publication Order Number: MC7900/D MC7900 Series MAXIMUM RATINGS (TA = +25°C, unless otherwise noted.) Rating Symbol Value Unit VI −35 −40 Vdc PD JA JC Internally Limited 65 5.0 W °C/W °C/W PD JA JC Internally Limited 70 5.0 W °C/W °C/W Storage Junction Temperature Range Tstg −65 to +150 °C Junction Temperature TJ +150 °C Input Voltage (−5.0 V ≥ VO ≥ −18 V) Input Voltage (24 V) Power Dissipation Case 221A TA = +25°C Thermal Resistance, Junction−to−Ambient Thermal Resistance, Junction−to−Case Case 936 (D2PAK) TA = +25°C Thermal Resistance, Junction−to−Ambient Thermal Resistance, Junction−to−Case Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied, damage may occur and reliability may be affected. *This device series contains ESD protection and exceeds the following tests: Human Body Model 2000 V per MIL_STD_883, Method 3015 Machine Model Method 200 V MC7905B, MC7905C ELECTRICAL CHARACTERISTICS (VI = −10 V, IO = 500 mA, Tlow* < TJ < +125°C, unless otherwise noted.) Characteristics Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) VO −4.8 −5.0 −5.2 Vdc Line Regulation (Note 1) (TJ = +25°C, IO = 100 mA) −7.0 Vdc ≥ VI ≥ − 25 Vdc −8.0 Vdc ≥ VI ≥ −12 Vdc (TJ = +25°C, IO = 500 mA) −7.0 Vdc ≥ VI ≥ − 25 Vdc −8.0 Vdc ≥ VI ≥ −12 Vdc Regline Load Regulation, TJ = +25°C (Note 1) 5.0 mA ≤ IO ≤ 1.5 A 250 mA ≤ IO ≤ 750 mA Regload Output Voltage −7.0 Vdc ≥ VI ≥ − 20 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W VO Input Bias Current (TJ = +25°C) IIB mV − − 7.0 2.0 50 25 − − 35 8.0 100 50 − − 11 4.0 100 50 − 4.75 − − 5.25 − 4.3 8.0 − − − − 1.3 0.5 mV Vdc IIB Input Bias Current Change −7.0 Vdc ≥ VI ≥ − 25 Vdc 5.0 mA ≤ IO ≤ 1.5 A mA mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 40 − V Ripple Rejection (IO = 20 mA, f = 120 Hz) RR − 70 − dB − 1.3 − − −1.0 − Dropout Voltage IO = 1.0 A, TJ = +25°C VI−VO Vdc VO/T Average Temperature Coefficient of Output Voltage IO = 5.0 mA, Tlow* ≤ TJ ≤ +125°C mV/°C 1. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. *Tlow = −40°C for MC7905B and Tlow = 0°C for MC7905C. http://onsemi.com 2 MC7900 Series MC7905AC ELECTRICAL CHARACTERISTICS (VI = −10 V, IO = 500 mA, 0°C < TJ < +125°C, unless otherwise noted.) Characteristics Output Voltage (TJ = +25°C) Symbol Min Typ Max Unit VO −4.9 −5.0 −5.1 Vdc − − − − 2.0 7.0 7.0 6.0 25 50 50 50 − − − 11 4.0 9.0 100 50 100 −4.80 − −5.20 − 4.4 8.0 − − − − − − 1.3 0.5 0.5 Line Regulation (Note 2) −8.0 Vdc ≥ VI ≥ −12 Vdc; IO = 1.0 A, TJ = +25°C −8.0 Vdc ≥ VI ≥ −12 Vdc; IO = 1.0 A −7.5 Vdc ≥ VI ≥ − 25 Vdc; IO = 500 mA −7.0 Vdc ≥ VI ≥ − 20 Vdc; IO = 1.0 A, TJ = +25°C Regline Load Regulation (Note 2) 5.0 mA ≤ IO ≤ 1.5 A, TJ = +25°C 250 mA ≤ IO ≤ 750 mA 5.0 mA ≤ IO ≤ 1.0 A Regload Output Voltage −7.5 Vdc ≥ VI ≥ − 20 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W VO Input Bias Current IIB mV mV Vdc IIB Input Bias Current Change −7.5 Vdc ≥ VI ≥ − 25 Vdc 5.0 mA ≤ IO ≤ 1.0 A 5.0 mA ≤ IO ≤ 1.5 A, TJ = +25°C mA mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 40 − V Ripple Rejection (IO = mA, f = 120 Hz) RR − 70 − dB VI−VO − 1.3 − Vdc − −1.0 − Dropout Voltage (IO = 1.0 A. TJ = +25°C) VO/T Average Temperature Coefficient of Output Voltage IO = 5.0 A, 0°C ≤ TJ ≤ +125°C mV/°C MC7905.2C ELECTRICAL CHARACTERISTICS (VI = −10 V, IO = 500 mA, 0°C < TJ < +125°C, unless otherwise noted.) Characteristics Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) VO −5.0 −5.2 −5.4 Vdc Line Regulation (Note 2) (TJ = +25°C, IO = 100 mA) −7.2 Vdc ≥ VI ≥ − 25 Vdc −8.0 Vdc ≥ VI ≥ −12 Vdc (TJ = +25°C, IO = 500 mA) −7.2 Vdc ≥ VI ≥ − 25 Vdc −8.0 Vdc ≥ VI ≥ −12 Vdc Regline Load Regulation, TJ = +25°C (Note 2) 5.0 mA ≤ IO ≤ 1.5 A 250 mA ≤ IO ≤ 750 mA Regload mV − − 8.0 2.2 52 27 − − 37 8.5 105 52 − − 12 4.5 105 52 −4.95 − −5.45 − 4.3 8.0 − − − − 1.3 0.5 Vn − 42 − Ripple Rejection (IO = 20 mA, f = 120 Hz) RR − 68 − dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI−VO − 1.3 − Vdc − −1.0 − Output Voltage −7.2 Vdc ≥ VI ≥ − 20 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W VO Input Bias Current (TJ = +25°C) IIB mV Vdc IIB Input Bias Current Change −7.2 Vdc ≥ VI ≥ − 25 Vdc 5.0 mA ≤ IO ≤ 1.5 A Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) mA VO/T Average Temperature Coefficient of Output Voltage IO = 5.0 mA, 0°C ≤ TJ ≤ +125°C mA V mV/°C 2. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 3 MC7900 Series MC7906C ELECTRICAL CHARACTERISTICS (VI = −11 V, IO = 500 mA, 0°C < TJ < +125°C, unless otherwise noted.) Characteristics Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) VO −5.75 −6.0 −6.25 Vdc Line Regulation (Note 3) (TJ = +25°C, IO = 100 mA) −8.0 Vdc ≥ VI ≥ − 25 Vdc −9.0 Vdc ≥ VI ≥ −13 Vdc (TJ = +25°C, IO = 500 mA) −8.0 Vdc ≥ VI ≥ − 25 Vdc −9.0 Vdc ≥ VI ≥ −13 Vdc Regline Load Regulation, TJ = +25°C (Note 3) 5.0 mA ≤ IO ≤ 1.5 A 250 mA ≤ IO ≤ 750 mA Regload Output Voltage −8.0 Vdc ≥ VI ≥ − 21 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W VO Input Bias Current (TJ = +25°C) IIB mV − − 9.0 3.0 60 30 − − 43 10 120 60 − − 13 5.0 120 60 −5.7 − −6.3 − 4.3 8.0 − − − − 1.3 0.5 mV Vdc IIB Input Bias Current Change −8.0 Vdc ≥ VI ≥ − 25 Vdc 5.0 mA ≤ IO ≤ 1.5 A mA mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 45 − V Ripple Rejection (IO = 20 mA, f = 120 Hz) RR − 65 − dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI−VO − 1.3 − Vdc − −1.0 − VO/T Average Temperature Coefficient of Output Voltage IO = 5.0 A, 0°C ≤ TJ ≤ +125°C mV/°C MC7908C ELECTRICAL CHARACTERISTICS (VI = −14 V, IO = 500 mA, 0°C < TJ < +125°C, unless otherwise noted.) Characteristics Output Voltage (TJ = +25°C) Symbol Min Typ Max Unit VO −7.7 −8.0 −8.3 Vdc Line Regulation (Note 3) (TJ = +25°C, IO = 100 mA) −10.5 Vdc ≥ VI ≥ −25 Vdc −11 Vdc ≥ VI ≥ −17 Vdc (TJ = +25°C, IO = 500 mA) −10.5 Vdc ≥ VI ≥ −25 Vdc −11 Vdc ≥ VI ≥ −17 Vdc Regline Load Regulation, TJ = +25°C (Note 3) 5.0 mA ≤ IO ≤ 1.5 A 250 mA ≤ IO ≤ 750 mA Regload mV − − 12 5.0 80 40 − − 50 22 160 80 − − 26 9.0 160 80 −7.6 − −8.4 − 4.3 8.0 − − − − 1.0 0.5 Vn − 52 − Ripple Rejection (IO = 20 mA, f = 120 Hz) RR − 62 − dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI−VO − 1.3 − Vdc − −1.0 − Output Voltage −10.5 Vdc ≥ VI ≥ − 23 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W VO Input Bias Current (TJ = +25°C) IIB mV Vdc IIB Input Bias Current Change −10.5 Vdc ≥ VI ≥ − 25 Vdc 5.0 mA ≤ IO ≤ 1.5 A Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) mA VO/T Average Temperature Coefficient of Output Voltage IO = 5.0 mA, 0°C ≤ TJ ≤ +125°C mA V mV/°C 3. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. http://onsemi.com 4 MC7900 Series MC7912B, MC7912C ELECTRICAL CHARACTERISTICS (VI = −19 V, IO = 500 mA, Tlow* < TJ < +125°C, unless otherwise noted.) Characteristics Output Voltage (TJ = +25°C) Symbol Min Typ Max Unit VO −11.5 −12 −12.5 Vdc Line Regulation (Note 4) (TJ = +25°C, IO = 100 mA) −14.5 Vdc ≥ VI ≥ − 30 Vdc −16 Vdc ≥ VI ≥ − 22 Vdc (TJ = +25°C, IO = 500 mA) −14.5 Vdc ≥ VI ≥ − 30 Vdc −16 Vdc ≥ VI ≥ − 22 Vdc Regline Load Regulation, TJ = +25°C (Note 4) 5.0 mA ≤ IO ≤ 1.5 A 250 mA ≤ IO ≤ 750 mA Regload Output Voltage −14.5 Vdc ≥ VI ≥ − 27 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W VO Input Bias Current (TJ = +25°C) IIB mV − − 13 6.0 120 60 − − 55 24 240 120 − − 46 17 240 120 −11.4 − −12.6 − 4.4 8.0 − − − − 1.0 0.5 mV Vdc IIB Input Bias Current Change −14.5 Vdc ≥ VI ≥ − 30 Vdc 5.0 mA ≤ IO ≤ 1.5 A mA mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 75 − V Ripple Rejection (IO = 20 mA, f = 120 Hz) RR − 61 − dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI−VO − 1.3 − Vdc − −1.0 − VO/T Average Temperature Coefficient of Output Voltage IO = 5.0 mA, Tlow* ≤ TJ ≤ +125°C mV/°C MC7912AC ELECTRICAL CHARACTERISTICS (VI = −19 V, IO = 500 mA, Tlow* < TJ < +125°C, unless otherwise noted.) Characteristics Symbol Min Typ Max Unit VO −11.75 −12 −12.25 Vdc − − − − 6.0 24 24 13 60 120 120 120 − − − 46 17 35 150 75 150 −11.5 − −12.5 − 4.4 8.0 − − − − − − 0.8 0.5 0.5 Vn − 75 − Ripple Rejection (IO = 20 mA, f = 120 Hz) RR − 61 − dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI−VO − 1.3 − Vdc − −1.0 − Output Voltage (TJ = +25°C) Line Regulation (Note 4) −16 Vdc ≥ VI ≥ − 22 Vdc; IO = 1.0 A, TJ = +25°C −16 Vdc ≥ VI ≥ − 22 Vdc; IO = 1.0 A −14.8 Vdc ≥ VI ≥ − 30 Vdc; IO = 500 mA −14.5 Vdc ≥ VI ≥ − 27 Vdc; IO = 1.0 A, TJ = +25°C Regline Load Regulation (Note 4) 5.0 mA ≤ IO ≤ 1.5 A, TJ = +25°C 250 mA ≤ IO ≤ 750 mA 5.0 mA ≤ IO ≤ 1.0 A Regload Output Voltage −14.8 Vdc ≥ VI ≥ − 27 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W mV mV VO Input Bias Current IIB Vdc IIB Input Bias Current Change −15 Vdc ≥ VI ≥ − 30 Vdc 5.0 mA ≤ IO ≤ 1.0 A 5.0 mA ≤ IO ≤ 1.5 A, TJ = +25°C Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) mA VO/T Average Temperature Coefficient of Output Voltage IO = 5.0 A, Tlow* ≤ TJ ≤ +125°C mA V mV/°C 4. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. *Tlow = −40°C for MC7912B and Tlow = 0°C for MC7912C. http://onsemi.com 5 MC7900 Series MC7915B, MC7915C ELECTRICAL CHARACTERISTICS (VI = − 23 V, IO = 500 mA, Tlow* < TJ < +125°C, unless otherwise noted.) Characteristics Output Voltage (TJ = +25°C) Symbol Min Typ Max Unit VO −14.4 −15 −15.6 Vdc Line Regulation (Note 5) (TJ = +25°C, IO = 100 mA) −17.5 Vdc ≥ VI ≥ − 30 Vdc −20 Vdc ≥ VI ≥ − 26 Vdc (TJ = +25°C, IO = 500 mA) −17.5 Vdc ≥ VI ≥ − 30 Vdc −20 Vdc ≥ VI ≥ − 26 Vdc Regline Load Regulation, TJ = +25°C (Note 5) 5.0 mA ≤ IO ≤ 1.5 A 250 mA ≤ IO ≤ 750 mA Regload Output Voltage −17.5 Vdc ≥ VI ≥ − 30 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W VO Input Bias Current (TJ = +25°C) IIB mV − − 14 6.0 150 75 − − 57 27 300 150 − − 68 25 300 150 −14.25 − −15.75 − 4.4 8.0 − − − − 1.0 0.5 mV Vdc IIB Input Bias Current Change −17.5 Vdc ≥ VI ≥ − 30 Vdc 5.0 mA ≤ IO ≤ 1.5 A mA mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 90 − V Ripple Rejection (IO = 20 mA, f = 120 Hz) RR − 60 − dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI−VO − 1.3 − Vdc − −1.0 − VO/T Average Temperature Coefficient of Output Voltage IO = 5.0 A, Tlow* ≤ TJ ≤ +125°C mV/°C MC7915AC ELECTRICAL CHARACTERISTICS (VI = − 23 V, IO = 500 mA, Tlow* < TJ < +125°C, unless otherwise noted.) Characteristics Symbol Min Typ Max Unit VO −14.7 −15 −15.3 Vdc − − − − 27 57 57 57 75 150 150 150 − − − 68 25 40 150 75 150 −14.4 − −15.6 − 4.4 8.0 − − − − − − 0.8 0.5 0.5 Vn − 90 − Ripple Rejection (IO = 20 mA, f = 120 Hz) RR − 60 − dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI−VO − 1.3 − Vdc − −1.0 − Output Voltage (TJ = +25°C) Line Regulation (Note 5) −20 Vdc ≥ VI ≥ − 26 Vdc, IO = 1.0 A, TJ = +25°C −20 Vdc ≥ VI ≥ − 26 Vdc, IO = 1.0 A, −17.9 Vdc ≥ VI ≥ − 30 Vdc, IO = 500 mA −17.5 Vdc ≥ VI ≥ − 30 Vdc, IO = 1.0 A, TJ = +25°C Regline Load Regulation (Note 5) 5.0 mA ≤ IO ≤ 1.5 A, TJ = +25°C 250 mA ≤ IO ≤ 750 mA 5.0 mA ≤ IO ≤ 1.0 A Regload Output Voltage −17.9 Vdc ≥ VI ≥ − 30 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W mV mV VO Input Bias Current IIB Vdc IIB Input Bias Current Change −17.5 Vdc ≥ VI ≥ − 30 Vdc 5.0 mA ≤ IO ≤ 1.0 A 5.0 mA ≤ IO ≤ 1.5 A, TJ = +25°C Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) mA VO/T Average Temperature Coefficient of Output Voltage IO = 5.0 mA, Tlow* ≤ TJ ≤ +125°C mA V mV/°C 5. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. *Tlow = −40°C for MC7915B and Tlow = 0°C for MC7915C. http://onsemi.com 6 MC7900 Series MC7918C ELECTRICAL CHARACTERISTICS (VI = − 27 V, IO = 500 mA, 0°C < TJ < +125°C, unless otherwise noted.) Characteristics Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) VO −17.3 −18 −18.7 Vdc Line Regulation (Note 6) (TJ = +25°C, IO = 100 mA) −21 Vdc ≥ VI ≥ − 33 Vdc −24 Vdc ≥ VI ≥ − 30 Vdc (TJ = +25°C, IO = 500 mA) −21 Vdc ≥ VI ≥ − 33 Vdc −24 Vdc ≥ VI ≥ − 30 Vdc Regline Load Regulation, TJ = +25°C (Note 6) 5.0 mA ≤ IO ≤ 1.5 A 250 mA ≤ IO ≤ 750 mA Regload Output Voltage −21 Vdc ≥ VI ≥ − 33 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W VO Input Bias Current (TJ = +25°C) IIB mV − − 25 10 180 90 − − 90 50 360 180 − − 110 55 360 180 −17.1 − −18.9 − 4.5 8.0 − − − − 1.0 0.5 mV Vdc IIB Input Bias Current Change −21 Vdc ≥ VI ≥ − 33 Vdc 5.0 mA ≤ IO ≤ 1.5 A mA mA Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) Vn − 110 − V Ripple Rejection (IO = 20 mA, f = 120 Hz) RR − 59 − dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI−VO − 1.3 − Vdc − −1.0 − VO/T Average Temperature Coefficient of Output Voltage IO = 5.0 mA, 0°C ≤ TJ ≤ +125°C mV/°C MC7924B, MC7924C ELECTRICAL CHARACTERISTICS (VI = − 33 V, IO = 500 mA, Tlow* < TJ < +125°C, unless otherwise noted.) Characteristics Symbol Min Typ Max Unit Output Voltage (TJ = +25°C) VO −23 −24 −25 Vdc Line Regulation (Note 6) (TJ = +25°C, IO = 100 mA) −27 Vdc ≥ VI ≥ − 38 Vdc −30 Vdc ≥ VI ≥ − 36 Vdc (TJ = +25°C, IO = 500 mA) −27 Vdc ≥ VI ≥ − 38 Vdc −30 Vdc ≥ VI ≥ − 36 Vdc Regline Load Regulation, TJ = +25°C (Note 6) 5.0 mA ≤ IO ≤ 1.5 A 250 mA ≤ IO ≤ 750 mA Regload mV − − 31 14 240 120 − − 118 70 470 240 − − 150 85 480 240 −22.8 − −25.2 − 4.6 8.0 − − − − 1.0 0.5 Vn − 170 − Ripple Rejection (IO = 20 mA, f = 120 Hz) RR − 56 − dB Dropout Voltage (IO = 1.0 A, TJ = +25°C) VI−VO − 1.3 − Vdc − −1.0 − Output Voltage −27 Vdc ≥ VI ≥ − 38 Vdc, 5.0 mA ≤ IO ≤ 1.0 A, P ≤ 15 W VO Input Bias Current (TJ = +25°C) IIB mV Vdc IIB Input Bias Current Change −27 Vdc ≥ VI ≥ − 38 Vdc 5.0 mA ≤ IO ≤ 1.5 A Output Noise Voltage (TA = +25°C, 10 Hz ≤ f ≤ 100 kHz) mA VO/T Average Temperature Coefficient of Output Voltage IO = 5.0 mA, Tlow* ≤ TJ ≤ +125°C mA V mV/°C 6. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account separately. Pulse testing with low duty cycle is used. *Tlow = −40°C for MC7924B and Tlow = 0°C for MC7924C. http://onsemi.com 7 MC7900 Series 20 HS = 5°C/W 5.0 4.0 HS = 15°C/W 3.0 2.0 I O , OUTPUT CURRENT (A) PD, POWER DISSIPATION (W) 2.5 Infinite Heatsink 10 No Heatsink 1.0 0.5 0.4 0.3 0.2 JC = 5° C/W JA = 65° C/W PD(max) = 15W 0.1 25 50 75 100 125 1.0 0.5 0 3.0 6.0 9.0 12 15 18 21 24 27 |VI −VO| INPUT−OUTPUT VOLTAGE DIFFERENTIAL (V) Figure 2. Worst Case Power Dissipation as a Function of Ambient Temperature Figure 3. Peak Output Current as a Function of Input−Output Differential Voltage 30 80 Vin = −11 V VO = −6.0 V IO = 20 mA 80 RR, RIPPLE REJECTION (dB) RR, RIPPLE REJECTION (dB) 1.5 TA, AMBIENT TEMPERATURE (°C) 60 40 20 10 100 1.0 k 10 k 60 50 f, FREQUENCY (Hz) 8.0 10 12 14 16 VO, OUTPUT VOLTAGE (V) Figure 4. Ripple Rejection as a Function of Frequency Figure 5. Ripple Rejection as a Function of Output Voltage 2.0 4.0 6.0 18 20 22 I IB , INPUT BIAS CURRENT (mA) 5.2 6.22 6.18 6.14 Vin = −11 V VD = −6.0 V IO = 20 mA 6.10 6.06 −25 f = 120 Hz IO = 20 mA Vin = 1.0 V(RMS) 70 40 100 k 6.26 VO, OUTPUT VOLTAGE (−V) TJ = +25°C 0 150 100 0 2.0 0 25 50 75 100 125 150 5.0 4.8 4.4 4.2 175 Vin = −11 V VO = −6.0 V IO = 20 mA 4.6 0 25 50 75 100 TJ, JUNCTION TEMPERATURE (°C) TJ, JUNCTION TEMPERATURE (°C) Figure 6. Output Voltage as a Function of Junction Temperature Figure 7. Quiescent Current as a Function of Temperature http://onsemi.com 8 125 MC7900 Series APPLICATIONS INFORMATION Design Considerations used to minimize ground loops and lead resistance drops since the regulator has no external sense lead. Bypassing the output is also recommended. The MC7900 Series of fixed voltage regulators are designed with Thermal overload Protection that shuts down the circuit when subjected to an excessive power overload condition. Internal Short Circuit Protection that limits the maximum current the circuit will pass, and Output Transistor Safe−Area Compensation that reduces the output short circuit current as the voltage across the pass transistor is increased. In many low current applications, compensation capacitors are not required. However, it is recommended that the regulator input be bypassed with a capacitor if the regulator is connected to the power supply filter with long wire lengths, or if the output load capacitance is large. An input bypass capacitor should be selected to provide good high−frequency characteristics to insure stable operation under all load conditions. A 0.33 F or larger tantalum, mylar, or other capacitor having low internal impedance at high frequencies should be chosen. The capacitor chosen should have an equivalent series resistance of less than 0.7. The bypass capacitor should be mounted with the shortest possible leads directly across the regulators input terminals. Normally good construction techniques should be −10 V Input 2N3055* or Equiv 10 F + Gnd 1.0 F + 10 IO = 200 mA R − VO ≤ 10 V 1.0 F Gnd Gnd The MC7905, −5.0 V regulator can be used as a constant current source when connected as above. The output current is the sum of resistor R current and quiescent bias current as follows. IO = 5.0 V R + IB The quiescent current for this regulator is typically 4.3 mA. The 5.0V regulator was chosen to minimize dissipation and to allow the output voltage to operate to within 6.0 V below the input voltage. Figure 8. Current Regulator +20 V Input 0.33 F 0.56 MJE200* or Equiv MC7905 + −5.0 V Output 0.56 0.56 −20 V Input +15 V Output MC7815 + 1.0 F 1.0 F + Gnd + MC7905* 5.6 + 1.0 F + 1.0 F −20 V Input Gnd 1.0 F 1.0 F MC7915 1N4001 or Equiv Gnd + −15 V Output *Mounted on heatsink. The MC7815 and MC7915 positive and negative regulators may be connected as shown to obtain a dual power supply for operational amplifiers. A clamp diode should be used at the output of the MC7815 to prevent potential latch−up problems whenever the output of the positive regulator (MC7815) is drawn below ground with an output current greater than 200 mA. When a boost transistor is used, short circuit currents are equal to the sum of the series pass and regulator limits, which are measured at 3.2 A and 1.8 A respectively in this case. Series pass limiting is approximately equal to 0.6 V/RSC. Operation beyond this point to the peak current capability of the MC7905C is possible if the regulator is mounted on a heatsink; otherwise thermal shutdown will occur when the additional load current is picked up by the regulator. Figure 9. Current Boost Regulator Figure 10. Operational Amplifier Supply (−5.0 V @ 4.0 A, with 5.0 A Current Limiting) (±15 @ 1.0 A) http://onsemi.com 9 JUNCTION-TO-AIR (° C/W) R θ JA, THERMAL RESISTANCE 80 3.5 PD(max) for TA = +50°C 70 3.0 Free Air Mounted Vertically 60 ÎÎÎ ÎÎÎ ÎÎÎ ÎÎÎ 2.0 oz. Copper L Minimum Size Pad 50 L 40 RJA 30 0 5.0 10 15 20 25 2.5 2.0 1.5 PD, MAXIMUM POWER DISSIPATION (W) MC7900 Series 1.0 30 L, LENGTH OF COPPER (mm) Figure 11. D2PAK Thermal Resistance and Maximum Power Dissipation versus P.C.B. Copper Length DEFINITIONS Input Bias Current − That part of the input current that is not delivered to the load. Output Noise Voltage − The rms AC voltage at the output, with constant load and no input ripple, measured over a specified frequency range. Long Term Stability − Output voltage stability under accelerated life test conditions with the maximum rated voltage listed in the devices’ electrical characteristics and maximum power dissipation. Line Regulation − The change in output voltage for a change in the input voltage. The measurement is made under conditions of low dissipation or by using pulse techniques such that the average chip temperature is not significantly affected. Load Regulation − The change in output voltage for a change in load current at constant chip temperature. Maximum Power Dissipation − The maximum total device dissipation for which the regulator will operate within specifications. http://onsemi.com 10 MC7900 Series ORDERING INFORMATION Device MC7905ACD2T Nominal Output Voltage −5.0 V Output Voltage Tolerance Package Operating Temperature Range Shipping† 2% D2PAK TJ = 0°C to +125°C 50 Units/Rail MC7905ACD2TG D2PAK (Pb−Free) 50 Units/Rail MC7905ACD2TR4 D2PAK 800 Tape & Reel D2PAK (Pb−Free) 800 Tape & Reel TO−220 50 Units/Rail TO−220 (Pb−Free) 50 Units/Rail MC7905ACD2TR4G MC7905ACT MC7905ACTG D2PAK 4% MC7905BD2T TJ = −40°C to +125°C D2PAK MC7905BD2TG 50 Units/Rail 50 Units/Rail (Pb−Free) MC7905BD2TR4 D2PAK 800 Tape & Reel MC7905BD2TR4G D2PAK 800 Tape & Reel (Pb−Free) MC7905BT TO−220 50 Units/Rail MC7905BTG TO−220 (Pb−Free) 50 Units/Rail MC7905CD2T D2PAK TJ = 0°C to +125°C 50 Units/Rail MC7905CD2TG D2PAK (Pb−Free) 50 Units/Rail MC7905CD2TR4 D2PAK 800 Tape & Reel D2PAK (Pb−Free) 800 Tape & Reel TO−220 50 Units/Rail TO−220 (Pb−Free) 50 Units/Rail MC7905CD2TR4G MC7905CT MC7905CTG MC7905.2CT −5.2 V 4% TO−220 MC7905.2CTG MC7906CD2T TJ = 0°C to +125°C TO−220 (Pb−Free) −6.0 V D2PAK 4% 50 Units/Rail TJ = 0°C to +125°C D2PAK MC7906CD2TG 50 Units/Rail 50 Units/Rail 50 Units/Rail (Pb−Free) MC7906CT MC7906CTG MC7908ACT −8.0 V 2% TO−220 50 Units/Rail TO−220 (Pb−Free) 50 Units/Rail TO−220 MC7908ACTG TJ = 0°C to +125°C 50 Units/Rail TO−220 (Pb−Free) 50 Units/Rail D2PAK 50 Units/Rail MC7908CD2TG D2PAK (Pb−Free) 50 Units/Rail MC7908CD2TR4 D2PAK 800 Tape & Reel D2PAK (Pb−Free) 800 Tape & Reel TO−220 50 Units/Rail TO−220 (Pb−Free) 50 Units/Rail MC7908CD2T 4% MC7908CD2TR4G MC7908CT MC7908CTG http://onsemi.com 11 MC7900 Series Device MC7912ACD2T Nominal Output Voltage −12 V Output Voltage Tolerance Package Operating Temperature Range Shipping† 2% D2PAK TJ = 0°C to +125°C 50 Units/Rail MC7912ACD2TG D2PAK (Pb−Free) 50 Units/Rail MC7912ACD2TR4 D2PAK 800 Tape & Reel MC7912ACD2TR4G D2PAK 800 Tape & Reel (Pb−Free) MC7912ACT MC7912ACTG 50 Units/Rail TO−220 (Pb−Free) 50 Units/Rail D2PAK 4% MC7912BD2T TO−220 TJ = −40°C to +125°C D2PAK MC7912BD2TG 50 Units/Rail 50 Units/Rail (Pb−Free) MC7912BD2TR4 D2PAK 800 Tape & Reel MC7912BD2TR4G D2PAK 800 Tape & Reel (Pb−Free) MC7912BT TO−220 50 Units/Rail MC7912BTG TO−220 (Pb−Free) 50 Units/Rail MC7912CD2T D2PAK TJ = 0°C to +125°C 50 Units/Rail MC7912CD2TG D2PAK (Pb−Free) 50 Units/Rail MC7912CD2TR4 D2PAK 800 Tape & Reel D2PAK (Pb−Free) 800 Tape & Reel TO−220 50 Units/Rail TO−220 (Pb−Free) 50 Units/Rail MC7912CD2TR4G MC7912CT MC7912CTG MC7915ACD2T − 15 V D2PAK 2% TJ = 0°C to +125°C D2PAK MC7915ACD2TG 50 Units/Rail 50 Units/Rail (Pb−Free) MC7915ACT MC7915ACTG MC7915BD2T TO−220 50 Units/Rail TO−220 (Pb−Free) 50 Units/Rail D2PAK 4% TJ = −40°C to +125°C D2PAK MC7915BD2TG 50 Units/Rail 50 Units/Rail (Pb−Free) MC7915BT TO−220 50 Units/Rail MC7915BTG TO−220 (Pb−Free) 50 Units/Rail MC7915CD2T D2PAK TJ = 0°C to +125°C 50 Units/Rail MC7915CD2TG D2PAK (Pb−Free) 50 Units/Rail MC7915CD2TR4 D2PAK 800 Tape & Reel MC7915CD2TR4G D2PAK 800 Tape & Reel (Pb−Free) MC7915CT MC7915CTG TO−220 50 Units/Rail TO−220 (Pb−Free) 50 Units/Rail http://onsemi.com 12 MC7900 Series Device MC7918CT Nominal Output Voltage Output Voltage Tolerance Package Operating Temperature Range Shipping† − 18 V 4% TO−220 TJ = 0°C to +125°C 50 Units/Rail MC7918CTG MC7924BT TO−220 (Pb−Free) − 24 V 4% TO−220 MC7924BTG TO−220 (Pb−Free) MC7924CD2T D2PAK MC7924CD2TG D2PAK 50 Units/Rail TJ = −40°C to +125°C 50 Units/Rail 50 Units/Rail TJ = 0°C to +125°C 50 Units/Rail 50 Units/Rail (Pb−Free) MC7924CT MC7924CTG TO−220 50 Units/Rail TO−220 (Pb−Free) 50 Units/Rail †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 13 MC7900 Series MARKING DIAGRAMS TO−220 T SUFFIX CASE 221A MC 79xxACT AWLYWW MC 7905.2CT AWLYWW MC 79xxBT AWLYWW MC 79xxCT AWLYWW 1 2 3 1 2 3 1 2 3 1 2 3 D2PAK D2T SUFFIX CASE 936 MC 79xxACD2T AWLYWW MC 79xxBD2T AWLYWW 2 1 MC 79xxCD2T AWLYWW 2 3 1 xx A WL Y WW 2 3 = Nominal Voltage = Assembly Location = Wafer Lot = Year = Work Week http://onsemi.com 14 1 3 MC7900 Series PACKAGE DIMENSIONS D2PAK D2T SUFFIX PLASTIC PACKAGE CASE 936−03 ISSUE B −T− K OPTIONAL CHAMFER A TERMINAL 4 E U S B F 1 2 3 V H M J D 0.010 (0.254) M T NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. TAB CONTOUR OPTIONAL WITHIN DIMENSIONS A AND K. 4. DIMENSIONS U AND V ESTABLISH A MINIMUM MOUNTING SURFACE FOR TERMINAL 4. 5. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH OR GATE PROTRUSIONS. MOLD FLASH AND GATE PROTRUSIONS NOT TO EXCEED 0.025 (0.635) MAXIMUM. P N G DIM A B C D E F G H J K L M N P R S U V L R C SOLDERING FOOTPRINT* 8.38 0.33 1.016 0.04 10.66 0.42 5.08 0.20 3.05 0.12 17.02 0.67 D2PAK−3 SCALE 3:1 mm inches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 15 INCHES MIN MAX 0.386 0.403 0.356 0.368 0.170 0.180 0.026 0.036 0.045 0.055 0.051 REF 0.100 BSC 0.539 0.579 0.125 MAX 0.050 REF 0.000 0.010 0.088 0.102 0.018 0.026 0.058 0.078 5 REF 0.116 REF 0.200 MIN 0.250 MIN MILLIMETERS MIN MAX 9.804 10.236 9.042 9.347 4.318 4.572 0.660 0.914 1.143 1.397 1.295 REF 2.540 BSC 13.691 14.707 3.175 MAX 1.270 REF 0.000 0.254 2.235 2.591 0.457 0.660 1.473 1.981 5 REF 2.946 REF 5.080 MIN 6.350 MIN MC7900 Series PACKAGE DIMENSIONS TO−220−3 T SUFFIX PLASTIC PACKAGE CASE 221A−09 ISSUE AA −T− B SEATING PLANE C F T S 4 DIM A B C D F G H J K L N Q R S T U V Z A Q 1 2 3 U H K Z L R V J NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION Z DEFINES A ZONE WHERE ALL BODY AND LEAD IRREGULARITIES ARE ALLOWED. G D N INCHES MIN MAX 0.570 0.620 0.380 0.405 0.160 0.190 0.025 0.035 0.142 0.147 0.095 0.105 0.110 0.155 0.018 0.025 0.500 0.562 0.045 0.060 0.190 0.210 0.100 0.120 0.080 0.110 0.045 0.055 0.235 0.255 0.000 0.050 0.045 −−− −−− 0.080 MILLIMETERS MIN MAX 14.48 15.75 9.66 10.28 4.07 4.82 0.64 0.88 3.61 3.73 2.42 2.66 2.80 3.93 0.46 0.64 12.70 14.27 1.15 1.52 4.83 5.33 2.54 3.04 2.04 2.79 1.15 1.39 5.97 6.47 0.00 1.27 1.15 −−− −−− 2.04 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada ON Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder Japan: ON Semiconductor, Japan Customer Focus Center 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 Phone: 81−3−5773−3850 http://onsemi.com 16 For additional information, please contact your local Sales Representative. MC7900/D