K4S51323PF-M(E)F Mobile-SDRAM 4M x 32Bit x 4 Banks Mobile-SDRAM FEATURES GENERAL DESCRIPTION • • • • The K4S51323PF is 536,870,912 bits synchronous high data rate Dynamic RAM organized as 4 x 4,196,304 words by 32 bits, fabricated with SAMSUNG’s high performance CMOS technology. Synchronous design allows precise cycle control with the use of system clock and I/O transactions are possible on every clock cycle. Range of operating frequencies, programmable burst lengths and programmable latencies allow the same device to be useful for a variety of high bandwidth and high performance memory system applications. 1.8V power supply. LVCMOS compatible with multiplexed address. Four banks operation. MRS cycle with address key programs. -. CAS latency (1, 2 & 3). -. Burst length (1, 2, 4, 8 & Full page). -. Burst type (Sequential & Interleave). • EMRS cycle with address key programs. • All inputs are sampled at the positive going edge of the system clock. • Burst read single-bit write operation. • Special Function Support. -. PASR (Partial Array Self Refresh). -. Internal TCSR (Temperature Compensated Self Refresh) -. DS (Driver Strength) • DQM for masking. • Auto refresh. • 64ms refresh period (8K cycle). • Commercial Temperature Operation (-25°C ~ 70°C). • 2Chips DDP 90Balls FBGA( -MXXX -Pb, -EXXX -Pb Free). ORDERING INFORMATION Part No. Max Freq. K4S51323PF-M(E)F75 133MHz(CL=3),83MHz(CL=2) K4S51323PF-M(E)F90 111MHz(CL=3),83MHz(CL=2) K4S51323PF-M(E)F1L 111MHz(CL=3)*1,66MHz(CL2) Interface Package LVCMOS 90 FBGA Pb (Pb Free) - M(E)F : Low Power, Commercial Temperature(-25°C ~ 70°C) Notes : 1. In case of 40MHz Frequency, CL1 can be supported. 2. Samsung are not designed or manufactured for use in a device or system that is used under circumstance in which human life is potentially at stake. Please contact to the memory marketing team in samsung electronics when considering the use of a product contained herein for any specific purpose, such as medical, aerospace, nuclear, military, vehicular or undersea repeater use. Address configuration Organization Bank Row Column Address 16Mx32 BA0,BA1 A0 - A12 A0 - A8 1 September 2004 K4S51323PF-M(E)F Mobile-SDRAM FUNCTIONAL BLOCK DIAGRAM I/O Control Data Input Register Bank Select 4M x 32 4M x 32 Output Buffer Sense AMP Row Decoder Row Buffer Refresh Counter ADD Address Register CLK 4M x 32 LWE LDQM DQi 4M x 32 Col. Buffer LCBR LRAS Column Decoder Latency & Burst Length LCKE Programming Register LRAS LCBR LWE LCAS LWCBR LDQM Timing Register CLK CKE CS RAS CAS WE 2 DQM September 2004 K4S51323PF-M(E)F Mobile-SDRAM Package Dimension and Pin Configuration < Top View*2 > < Bottom View*1 > E1 9 8 7 6 5 90Ball(6x15) FBGA 4 3 2 1 1 2 3 7 8 9 A DQ26 DQ24 VSS VDD DQ23 DQ21 B B DQ28 VDDQ VSSQ VDDQ VSSQ DQ19 C C VSSQ DQ27 DQ25 DQ22 DQ20 VDDQ D D VSSQ DQ29 DQ30 DQ17 DQ18 VDDQ E VDDQ DQ31 NC NC DQ16 VSSQ F VSS DQM3 A3 A2 DQM2 VDD G A4 A5 A6 A10 A0 A1 e A D E F D1 G H J K D/2 L M N P R H A7 A8 A12 NC BA1 A11 J CLK CKE A9 BA0 CS RAS K DQM1 NC NC CAS WE DQM0 L VDDQ DQ8 VSS VDD DQ7 VSSQ M VSSQ DQ10 DQ9 DQ6 DQ5 VDDQ N VSSQ DQ12 DQ14 DQ1 DQ3 VDDQ P DQ11 VDDQ VSSQ VDDQ VSSQ DQ4 R DQ13 DQ15 VSS VDD DQ0 DQ2 E E/2 A A1 Substrate(2Layer) z b < Top View*2 > #A1 Ball Origin Indicator Pin Name Pin Function CLK System Clock CS Chip Select CKE Clock Enable A0 ~ A12 Address BA0 ~ BA1 Bank Select Address RAS Row Address Strobe CAS Column Address Strobe WE Write Enable DQM0 ~ DQM3 Data Input/Output Mask DQ0 ~ 31 Data Input/Output SAMSUNG Power Supply/Ground Data Output Power/Ground [Unit::mm] Week K4S51323PF-XXXX VDD/VSS VDDQ/VSSQ 3 Symbol Min Typ Max A - 1.30 1.40 A1 0.27 0.32 0.37 E - 11.0 - E1 - 6.40 - D - 13.0 - D1 - 11.2 - e - 0.80 - b 0.45 0.50 0.55 z - - 0.10 September 2004 K4S51323PF-M(E)F Mobile-SDRAM ABSOLUTE MAXIMUM RATINGS Parameter Symbol Value Unit Voltage on any pin relative to Vss VIN, VOUT -1.0 ~ 2.6 V Voltage on VDD supply relative to Vss VDD, VDDQ -1.0 ~ 2.6 V TSTG -55 ~ +150 °C Power dissipation PD 1.0 W Short circuit current IOS 50 mA Storage temperature NOTES: Permanent device damage may occur if ABSOLUTE MAXIMUM RATINGS are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. DC OPERATING CONDITIONS Recommended operating conditions (Voltage referenced to VSS = 0V, TA = -25 to 70°C) Parameter Symbol Min Typ Max Unit Note VDD 1.7 1.8 1.95 V VDDQ 1.7 1.8 1.95 V Input logic high voltage VIH 0.8 x VDDQ 1.8 VDDQ + 0.3 V 1 Input logic low voltage VIL -0.3 0 0.3 V 2 Output logic high voltage VOH VDDQ -0.2 - - V IOH = -0.1mA Output logic low voltage VOL - - 0.2 V IOL = 0.1mA ILI -2 - 2 uA 3 Supply voltage Input leakage current NOTES : 1. VIH (max) = 2.2V AC.The overshoot voltage duration is ≤ 3ns. 2. VIL (min) = -1.0V AC. The undershoot voltage duration is ≤ 3ns. 3. Any input 0V ≤ VIN ≤ VDDQ. Input leakage currents include Hi-Z output leakage for all bi-directional buffers with tri-state outputs. 4. Dout is disabled, 0V ≤ VOUT ≤ VDDQ. CAPACITANCE (VDD = 1.8V, TA = 23°C, f = 1MHz, VREF =0.9V ± 50 mV) Pin Symbol Min Max Unit CCLK 3.0 6.0 pF RAS, CAS, WE, CS, CKE CIN 3.0 6.0 pF DQM CIN 1.5 3.0 pF Address CADD 3.0 6.0 pF DQ0 ~ DQ31 COUT 3.0 5.0 pF Clock 4 Note September 2004 K4S51323PF-M(E)F Mobile-SDRAM DC CHARACTERISTICS Recommended operating conditions (Voltage referenced to VSS = 0V, TA = -25 to 70°C) Version Parameter Operating Current (One Bank Active) Precharge Standby Current in power-down mode Symbol ICC1 ICC2P Active Standby Current in power-down mode Active Standby Current in non power-down mode (One Bank Active) Operating Current (Burst Mode) Refresh Current Self Refresh Current Burst length = 1 tRC ≥ tRC(min) IO = 0 mA -75 -90 -1L 100 90 80 CKE ≤ VIL(max), tCC = 10ns ICC3NS mA 1 mA CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 10ns Input signals are changed one time during 20ns 20 mA 2 CKE ≤ VIL(max), tCC = 10ns 10 mA ICC3PS CKE & CLK ≤ VIL(max), tCC = ∞ ICC3N Note 0.6 CKE ≥ VIH(min), CLK ≤ VIL(max), tCC = ∞ ICC2NS Input signals are stable ICC3P Unit 0.6 ICC2PS CKE & CLK ≤ VIL(max), tCC = ∞ ICC2N Precharge Standby Current in non power-down mode Test Condition 2 CKE ≥ VIH(min), CS ≥ VIH(min), tCC = 10ns Input signals are changed one time during 20ns 40 mA CKE ≥ VIH(min), CLK ≤ VIL(max), tCC = ∞ Input signals are stable 10 mA ICC4 IO = 0 mA Page burst 4Banks Activated tCCD = 2CLKs 150 120 120 mA 1 ICC5 tRC ≥ tRC(min) 170 170 170 mA 2 °C 3 ICC6 CKE ≤ 0.2V Internal TCSR Max 40 Max 70 Full Array 400 900 1/2 of Full Array 320 600 1/4 of Full Array 280 500 uA NOTES: 1. Measured with outputs open. 2. Refresh period is 64ms. 3. Internal TCSR can be supported(In commercial Temp : Max 40°C/Max 70°C). 4. Unless otherwise noted, input swing IeveI is CMOS(VIH /VIL=VDDQ/VSSQ). 5 September 2004 K4S51323PF-M(E)F Mobile-SDRAM AC OPERATING TEST CONDITIONS(VDD = 1.7V ∼ 1.95V, TA = -25 to 70°C for Commercial) Parameter AC input levels (Vih/Vil) Value Unit 0.9 x VDDQ / 0.2 V 0.5 x VDDQ V tr/tf = 1/1 ns 0.5 x VDDQ V Input timing measurement reference level Input rise and fall time Output timing measurement reference level Output load condition See Figure 2 1.8V 13.9KΩ Vtt=0.5 x VDDQ VOH (DC) = VDDQ - 0.2V, IOH = -0.1mA Output VOL (DC) = 0.2V, IOL = 0.1mA 10.6KΩ 50Ω 20pF Output Z0=50Ω 20pF Figure 1. DC Output Load Circuit Figure 2. AC Output Load Circuit 6 September 2004 K4S51323PF-M(E)F Mobile-SDRAM OPERATING AC PARAMETER (AC operating conditions unless otherwise noted) Version Parameter Symbol -75 -90 -1L Unit Note Row active to row active delay tRRD(min) 15 18 18 ns 1 RAS to CAS delay tRCD(min) 22.5 24 27 ns 1 Row precharge time tRP(min) 22.5 24 27 ns 1 tRAS(min) 50 50 50 ns 1 Row active time tRAS(max) Row cycle time tRC(min) Last data in to row precharge tRDL(min) Last data in to Active delay 100 72.5 74 us ns 1 15 ns 2 tDAL(min) tRDL + tRP - Last data in to new col. address delay tCDL(min) 1 CLK 2 Last data in to burst stop tBDL(min) 1 CLK 2 Auto refresh cycle time tARFC(min) 80 ns Exit self refresh to active command tSRFX(min) 120 ns Col. address to col. address delay tCCD(min) 1 CLK 3 ea 4 Number of valid output data CAS latency=3 2 Number of valid output data CAS latency=2 1 Number of valid output data CAS latency=1 - 77 0 NOTES: 1. The minimum number of clock cycles is determined by dividing the minimum time required with clock cycle time and then rounding off to the next higher integer. 2. Minimum delay is required to complete write. 3. All parts allow every cycle column address change. 4. In case of row precharge interrupt, auto precharge and read burst stop. 7 September 2004 K4S51323PF-M(E)F Mobile-SDRAM AC CHARACTERISTICS(AC operating conditions unless otherwise noted) -75 Parameter -90 -1L Symbol Min Max Min Max Unit Note ns 1 ns 1,2 ns 2 Max CAS latency=3 tCC 7.5 CAS latency=2 tCC 12 CAS latency=1 tCC - CAS latency=3 tSAC 6 7 7 CAS latency=2 tSAC 9 9 10 CAS latency=1 tSAC - - 20 CAS latency=3 tOH 2.0 2.0 2.0 CAS latency=2 tOH 2.0 2.0 2.0 CAS latency=1 tOH - - 2.0 CLK high pulse width tCH 2.5 3.0 3.0 ns 3 CLK low pulse width tCL 2.5 3.0 3.0 ns 3 Input setup time tSS 2.0 2.0 2.0 ns 3 Input hold time tSH 1 1 1.5 ns 3 CLK to output in Low-Z tSLZ 1 1 1 ns 2 CLK cycle time CLK to valid output delay Output data hold time 9 Min 1000 CAS latency=2 1000 - CAS latency=3 CLK to output in Hi-Z 12 9 tSHZ CAS latency=1 15 1000 25 6 7 7 9 9 10 - - 20 ns NOTES : 1. Parameters depend on programmed CAS latency. 2. If clock rising time is longer than 1ns, (tr/2-0.5)ns should be added to the parameter. 3. Assumed input rise and fall time (tr & tf) = 1ns. If tr & tf is longer than 1ns, transient time compensation should be considered, i.e., [(tr + tf)/2-1]ns should be added to the parameter. 8 September 2004 K4S51323PF-M(E)F Mobile-SDRAM SIMPLIFIED TRUTH TABLE COMMAND Register CKEn-1 CKEn Mode Register Set H Auto Refresh X Entry Self Refresh RAS CAS WE L L L L X OP CODE L L L H X X L H H H Exit 3 L L 3 H 3 X H X X X X 3 Bank Active & Row Addr. H X L L H H X V Read & Auto Precharge Disable Column Address Auto Precharge Enable H X L H L H X V Write & Auto Precharge Disable Column Address Auto Precharge Enable H X L H L L X V Burst Stop H X L H H L X Precharge Column Address (A0~A8) H L H X L L H L H H X X X L V V V X X X X H X X X L H H H H X X X L V V V L Exit L H Entry H L Precharge Power Down Mode Column Address (A0~A8) H X V L X H X All Banks Entry Row Address L Bank Selection Clock Suspend or Active Power Down 1, 2 H H Refresh DQM BA0,1 A10/AP A12,A11, Note A9 ~ A0 CS 4 4, 5 4 4, 5 6 X X X X X X Exit L DQM H No Operation Command H H X X H X X X L H H H X V X X X 7 (V=Valid, X=Don′t Care, H=Logic High, L=Logic Low) NOTES : 1. OP Code : Operand Code A0 ~ A12 & BA0 ~ BA1 : Program keys. (@MRS) 2. MRS can be issued only at all banks precharge state. A new command can be issued after 2 CLK cycles of MRS. 3. Auto refresh functions are the same as CBR refresh of DRAM. The automatical precharge without row precharge command is meant by "Auto". Auto/self refresh can be issued only at all banks precharge state. Partial self refresh can be issued only after setting partial self refresh mode of EMRS. 4. BA0 ~ BA1 : Bank select addresses. 5. During burst read or write with auto precharge, new read/write command can not be issued. Another bank read/write command can be issued after the end of burst. New row active of the associated bank can be issued at tRP after the end of burst. 6. Burst stop command is valid at every burst length. 7. DQM sampled at the positive going edge of CLK masks the data-in at that same CLK in write operation (Write DQM latency is 0), but in read operation, it makes the data-out Hi-Z state after 2 CLK cycles. (Read DQM latency is 2). 9 September 2004 K4S51323PF-M(E)F Mobile-SDRAM A. MODE REGISTER FIELD TABLE TO PROGRAM MODES Register Programmed with Normal MRS Address Function BA0 ~ BA1 A12 ~ A10/AP A9*2 "0" Setting for Normal MRS RFU*1 W.B.L A8 A7 A6 Test Mode A5 A4 A3 CAS Latency A2 BT A1 A0 Burst Length Normal MRS Mode Test Mode CAS Latency Burst Type Burst Length A8 A7 Type A6 A5 A4 Latency A3 Type A2 A1 A0 BT=0 BT=1 0 0 Mode Register Set 0 0 0 Reserved 0 Sequential 0 0 0 1 1 0 1 Reserved 0 0 1 1 1 Interleave 0 0 1 2 2 1 0 Reserved 0 1 0 2 0 1 0 4 4 1 1 Reserved 0 1 1 3 0 1 1 8 8 Write Burst Length 1 0 0 Reserved 1 0 0 Reserved Reserved 1 0 1 Reserved Reserved 1 1 0 Reserved Reserved 1 1 1 Full Page Reserved A9 Length 1 0 1 Mode Select BA1 BA0 Setting for Normal MRS Reserved 0 0 Burst 1 1 0 Reserved 1 Single Bit 1 1 1 Reserved Mode 0 Full Page Length x32 : 512Mb(512) Register Programmed with Extended MRS Address BA1 Function BA0 A12 ~ A10/AP Mode Select A9 A8 A7 A6 A5 A4 DS RFU*1 A3 A2 A1 A0 PASR RFU*1 EMRS for PASR(Partial Array Self Ref.) & DS(Driver Strength) Mode Select Driver Strength PASR BA1 BA0 Mode A6 A5 Driver Strength A2 A1 A0 Size of Refreshed Area 0 0 Normal MRS 0 0 Full 0 0 0 Full Array 0 1 Reserved 0 1 1/2 0 0 1 1/2 of Full Array 1 0 EMRS for Mobile SDRAM 1 0 1/4 0 1 0 1/4 of Full Array 1 1 Reserved 1 1 1/8 0 1 1 Reserved 1 0 0 Reserved 1 0 1 Reserved 1 1 0 Reserved 1 1 1 Reserved Reserved Address A12~A10/AP A9 A8 A7 A4 A3 0 0 0 0 0 0 NOTES: 1.RFU(Reserved for future use) should stay "0" during MRS cycle. 2.If A9 is high during MRS cycle, "Burst Read Single Bit Write" function will be enabled. 10 September 2004 K4S51323PF-M(E)F Mobile-SDRAM Partial Array Self Refresh 1. In order to save power consumption, Mobile SDRAM has PASR option. 2. Mobile SDRAM supports 3 kinds of PASR in self refresh mode : Full Array, 1/2 of Full Array, 1/4 of Full Array BA1=0 BA0=0 BA1=0 BA0=1 BA1=0 BA0=0 BA1=0 BA0=1 BA1=0 BA0=0 BA1=0 BA0=1 BA1=1 BA0=0 BA1=1 BA0=1 BA1=1 BA0=0 BA1=1 BA0=1 BA1=1 BA0=0 BA1=1 BA0=1 - Full Array - 1/2 Array - 1/4 Array Partial Self Refresh Area Internal Temperature Compensated Self Refresh (TCSR) Note : 1. In order to save power consumption, Mobile-SDRAM includes the internal temperature sensor and control units to control the self refresh cycle automatically according to the two temperature range ; Max. 40 °C, Max. 70 °C. 2. If the EMRS for external TCSR is issued by the controller, this EMRS code for TCSR is ignored. Self Refresh Current (Icc 6) Temperature Range Unit Full Array 1/2 of Full Array 1/4 of Full Array Max. 40 °C 400 320 280 Max. 70 °C 900 600 500 uA B. POWER UP SEQUENCE 1. Apply power and attempt to maintain CKE at a high state and all other inputs may be undefined. - Apply VDD before or at the same time as VDDQ. 2. Maintain stable power, stable clock and NOP input condition for a minimum of 200us. 3. Issue precharge commands for all banks of the devices. 4. Issue 2 or more auto-refresh commands. 5. Issue a mode register set command to initialize the mode register. 6. Issue a extended mode register set command to define DS or PASR operating type of the device after normal MRS. EMRS cycle is not mandatory and the EMRS command needs to be issued only when DS or PASR is used. The default state without EMRS command issued is the half driver strength and full array refreshed. The device is now ready for the operation selected by EMRS. For operating with DS or PASR , set DS or PASR mode in EMRS setting stage. In order to adjust another mode in the state of DS or PASR mode, additional EMRS set is required but power up sequence is not needed again at this time. In that case, all banks have to be in idle state prior to adjusting EMRS set. 11 September 2004 K4S51323PF-M(E)F Mobile-SDRAM C. BURST SEQUENCE 1. BURST LENGTH = 4 Initial Address Sequential Interleave A1 A0 0 0 0 1 2 3 0 1 2 3 0 1 1 2 3 0 1 0 3 2 1 0 2 3 0 1 2 3 0 1 1 1 3 0 1 2 3 2 1 0 2. BURST LENGTH = 8 Initial Address Sequential Interleave A2 A1 A0 0 0 0 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 0 1 1 2 3 4 5 6 7 0 1 0 3 2 5 4 7 6 0 1 0 2 3 4 5 6 7 0 1 2 3 0 1 6 7 4 5 0 1 1 3 4 5 6 7 0 1 2 3 2 1 0 7 6 5 4 1 0 0 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 1 0 1 5 6 7 0 1 2 3 4 5 4 7 6 1 0 3 2 1 1 0 6 7 0 1 2 3 4 5 6 7 4 5 2 3 0 1 1 1 1 7 0 1 2 3 4 5 6 7 6 5 4 3 2 1 0 12 September 2004