Ordering number : EN5798 Monolithic Digital IC LB1855NM 3-Phase Brushless Motor Driver Overview The LB1855NM is a 3-phase brushless motor driver IC that is optimal for VCR drum motor drive. • Current limiter circuit built in • AGC circuit built in • Thermal shutdown circuit built in Features Package Dimensions • Current linear drive • No output electrolytic capacitors required. unit: mm 3097-MFP16FS Allowable power dissipation, Pd max — W [LB1855NM] On the specified printed circuit board (a 20 × 30 × 1.5 mm glass3 epoxy board) SANYO: MFP16FS Ambient temperature, Ta — °C Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit Maximum supply voltage VCC max 20 V Maximum output current IO max 1.2 A 1.2 W Allowable power dissipation Pd max On the specified printed circuit board (a 20 × 30 × 1.5 mm3 glass epoxy board) Operating temperature Topr –20 to +75 °C Storage temperature Tstg –55 to +150 °C Ratings Unit Allowable Operating Ranges at Ta = 25°C Parameter Supply current Symbol Conditions VCC Hall input amplitude VHALL 7 to 18 Between the Hall inputs 70 to 300 V mVp-p Any and all SANYO products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft’s control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO representative nearest you before using any SANYO products described or contained herein in such applications. SANYO assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO products described or contained herein. SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN O3098RM (OT) No. 5798-1/5 LB1855NM Electrical Characteristics at Ta = 25°C, VCC = 12 V Parameter Supply current Symbol Conditions ICC VC = GND VREF IR = 8 mA Upper side Vsat1 Lower side Vsat2 Upper side IOL1 Lower side IOL2 VHO * Reference voltage Ratings min typ Unit max 8 6.0 mA 6.3 6.6 V IO = 1 A 1.5 1.9 V IO = 1 A 0.8 1.2 V VCC = 18 V 50 µA VCC = 18 V 50 µA –10 +10 mV 2.2 VCC – 0.7 [Saturation voltage] [Leakage current] [Hall Amplifier] Input offset voltage Common-mode input voltage range VHCM V [Control Amplifier] Control reference voltage VREF1 Control Gm VG Input current IIN (the VCREF pin voltage) × 23/16 Rf = 1Ω 2.1 2.3 2.5 1 V A/V 10 µA [Thermal Shutdown Circuit] Operating temperature Hysteresis TTSD * 180 °C ∆TTSD * 15 °C Note: Items marked with an asterisk (*) are design target values and are not tested. Pin Assignment Block Diagram However, note that certain motors may require output capacitors to prevent oscillation. No. 5798-2/5 LB1855NM Sample Application Circuit Hall input voltage range: 2.2 to (VCC – 0.7) V DC 70 mV p-p to 300 mV p-p AC However, note that certain motors may require output capacitors to prevent oscillation. Truth Table Item Source → sink 1 Input U V W V phase → W phase H H L 2 U phase → W phase H L L 3 W phase → V phase L L H 4 V phase → U phase L H L 5 U phase → V phase H L H 6 W phase → U phase L H H Input: “H” indicates that the input phase 1 is at least 0.2 V higher than phase 2. “L” indicates that the input phase 1 is at least 0.2 V lower than phase 2. Pin Functions Pin No. Pin 1 FC 2 VCC 3 4 5 WOUT VOUT UOUT 6 Rf Pin voltage (V) Pin description Equivalent circuit • Frequency characteristics correction Oscillation in the current control closed loop can be prevented by inserting a capacitor between this pin and VREF. 7 to 18 • Power supply pin • Outputs pin • Ground for the output transistor The output current can be detected as a voltage by inserting the resistor Rf between this pin and ground to provide fixed current drive. The current limiter also operates by detecting this voltage. Continued on next page. No. 5798-3/5 LB1855NM Continued from preceding page. Pin No. Pin Pin voltage (V) Pin description 7 AGC • AGC pin The Hall amplifier gain can be controlled according to the amplitude of the Hall input by inserting a capacitor between this pin and ground. 8 VREF • Internal reference voltage. About 6.3 V. 9 10 11 12 13 14 UIN1 UIN2 VIN1 VIN2 WIN1 WIN2 2.2 to VCC – 0.7 15 16 VCREF VC 0 to 5 Equivalent circuit • Hall element inputs pin • Speed control pin This IC adopts a current control type in which the output current is controlled by the pin 16 voltage. The control start voltage changes about 1.3 to 1.4 V if pin 15 is connected to ground. No. 5798-4/5 LB1855NM Specifications of any and all SANYO products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer’s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer’s products or equipment. SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO products (including technical data, services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Electric Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the “Delivery Specification” for the SANYO product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of October, 1998. Specifications and information herein are subject to change without notice. PS No. 5798-5/5