Ordering number: EN 2658A PMOS LSI LM8562 Digital Alarm Clock Overview Package Dimensions The LM8562 is a digital clock-use LSI having features such as easy setting, two alarms. Since the LM8562 is designed to be able to direct drive an LED panel of duplex type, the package in which the LM8562 is placed is a 28-pin shrink DIP with a small mounting area. unit : mm 3029A-DIP28S [LM8562] Features (1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) Duplex LED display (LM8560-use LED panel usable) Two alarms on chip (600 Hz, 1200 Hz) Up, down/fast, slow time setting available (easy setting) 12/24-hour mode, 50/60 Hz selectable (provided that it is impossible to select the combination of 24-hour mode and 60 Hz) On-chip CR oscillator for backup use at the time of power failure Power failure indicator 59-minute alarm/sleep timer 6-minute snooze function Radio output function P-channel ED MOS Pin 28 dual-in-line shrink package Wide operating voltage/operating temperature range VDD= –14 to –8 V / –20 to +70°C SANYO : DIP28S Specifications Absolute Maximum Ratings at Ta = 25°C, VSS = 0 V Parameter Supply voltage Input voltage Output voltage Ratings Unit VDD max Symbol Conditions –17.0 to +0.3 V VIN –17.0 to +0.3 V VOUT Allowable power dissipation Pd max Ta = 70°C –17.0 to +0.3 V 0.7 W Operating temperature Topr –20 to +70 °C Storage temperature Tstg –55 to +125 °C SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN D2897HA (II)/6209TA No.2658-1/7 LM8562 Allowable Operating Conditions at Ta = –20 to +70°C, VSS = 0 V Parameter Supply voltage Standby voltage Input high-level voltage Input low-level voltage Input high-level voltage Input low-level voltage Input high-level voltage Input mid-level voltage Input low-level voltage Input high-level voltage Input low-level voltage Input level hold time Input chattering time Symbol VDD VST VIH1 VIL1 VIH2 VIL2 VIH3 VIM VIL3 VIH4 VIL4 tH tC Conditions min typ –14 50/60 Hz INPUT pin VSS–1 CR OSC pin VSS–1 3-level input pins Input pins other than the above max –8 –7.5 VSS VDD+2 VSS VDD + 2 VSS 1/2 VDD + 1 VDD + 1 VSS VDD + 2 VSS – 0.7 1/2 VDD – 1 VDD VSS – 2 10 10 Unit V V V V V V V V V V V ms ms Electrical Characteristics at Ta = 25 ± 2°C, VSS = 0 V, VDD = –12 V Parameter Symbol Output high-level current IOH1 Output OFF-state leakage current IOF1 Output high-level current IOH2 Output OFF-state leakage current IOF2 Output high-level current IOH3 Output OFF-state leakage current Operating frequency Input high-level current Input low-level current Input high-level current Input low-level current Input high-level current Input low-level current Pull-down resistance Pull-up resistance Operating current Power failure detect circuit OSC stability OSC accuracy OSC frequency IOF3 fop IIH1 IIL1 IIH2 IIL2 IIH3 IIL3 RPD RPU IDD VBU fS fA fOSC Conditions AM & 10’SHR ag & de pin, VOUT = VSS – 2.0 V VOUT = VDD Segment output pins other than the above, VOUT = VSS – 2.0 V VOUT = VDD ALM-1, ALM-2, RADIO OUTPUT pin, VOUT = VSS – 2.0 V VOUT = VDD 50/60 Hz INPUT pin VIH = VSS VIL = VDD CR OSC pin, VIH = VSS VIL = VDD 3-level input pins, VIH = VSS VIL = VDD 3-level input pins, VIN = 1/2 VDD VIN = 1/2VDD Output : No load VDD = –9 V ± 10% VDD = –9 V R = 180 kΩ, C = 3300 pF min typ 32 16 max Unit (Note1) mA 20 µA (Note1) mA 20 µA 2 mA 10 2000 10 DC –10 10 60 20 –120 2 –7.5 –10 –10 120 –20 1.0 0.8 8 –5.0 15 10 10 2400 µA Hz µA µA µA µA µA µA MΩ MΩ mA V % % Hz Note 1 : The allowable segment current drain is 78 mA max. for AM & 10’SHR ag & de and 39 mA max. for other than AM & 10’SHR ag & de in the range of power dissipation 700 mW. No.2658-2/7 LM8562 Pin Assignment Pin Functions 1. 3-Level Input Pins No. 17 21 22 23 24 26 27 Pin Name SPEED/POWER DOWN ALM-DISP SELECT TIME SET INPUT ON/OFF INPUT SLEEP/SNOOZE MODE SELECT RT-TIME SET/DIMMER VSS Test mode Alarm 2 display & setting Slow-down (AC = fast-down) ON Sleep display & sleep-in 24-hour mode, 50 Hz Time setting inhibit Dimmer display Input Level OPEN Normal NOP NOP NOP NOP 12-hour mode, 50 Hz Timer setting inhibit Normal display VDD Power-down mode Alarm 1 display & setting Slow-up (AC = fast-up) OFF Second display & snooze-in 12-hour mode, 60 Hz Time setting enable Normal display NOP : No operation AC : Pulse input 2. Input/Output Pins No. 18 19 20 16 3. Pin Name RADIO OUTPUT ALM-1 OUTPUT ALM-2 OUTPUT CR OSC Input Level VSS — — — VDD When not used Alarm1 OFF Alarm2 OFF 1-pin OSC circuit Input Pins No.25 50/60 Hz INPUT = 50 Hz or 60 Hz clock signal input No.15, 28 VSS, VDD = Power supply pin No.2658-3/7 LM8562 4. Output Pins No. Drive Phase Pin Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 AM & 10’SHR ag & de PM & 10’SHR b 10’SHR c & HR e HR b & g HR c & d HR a & f 10’SMIN a & f 10’SMIN b & g 10’SMIN c & d 10’SMIN e & MIN e MIN b & g MIN c & d MIN a & f COLON OUTPUT 1 AM 10’SHR ad PM HR e HR g HR d HR f 10’SMIN a 10’SMIN b 10’SMIN c MIN e MIN g MIN d MIN f COLON 2 10’SHR eg 10’SHR b 10’SHR c HR b HR c HR a 10’SMIN f 10’SMIN g 10’SMIN d 10’SMIN e MIN b MIN c MIN a — Display Mode ALM-DISP SELECT Select Pin SLEEP/SNOOZE INPUT Display Mode Digit No. 1 AM/PM 10’s hour AM/PM 10’s hour AM/PM 10’s hour 2 OPEN OPEN Time display Hour VDD OPEN Alarm 1 VSS OPEN Alarm 2 OPEN (VDD, VSS) VSS Sleep Unlit 0 OPEN (VDD, VSS) VDD second display Unlit Minutes Hour Hour 3 10’s minutes 10’s minutes 10’s minutes 10’s minutes 10’s seconds 4 Minutes Minutes Minutes Minutes Seconds Operation Description 1. Segment Output The duplex LED panel can be direct driven by 13 segment output pins. (Compatible with LM8560-use LED panel) 2. Colon Output LED panel Colon The drive phase is phase 1. The colon always flashes at 1 Hz rate. 3. 4. OSC Circuit By connecting a resistor and a capacitor with the CR INPUT pin, a 2.4 kHz OSC circuit is formed. The clock signal generated by the 2.4 kHz OSC circuit is used in the following cases. (1) Used as the clock signal for the time counter, instead of 50/60 Hz INPUT, when the power-down mode is entered. (2) Alarm sound (1200 Hz or 600 Hz) at the alarm signal output mode (3) 1/25 duty clock signal while the dimmer is in operation Power-Down Mode (1) Since the backup OSC circuit holds the current time, the LM8562 starts operating immediately. (2) The snooze function stops operating. (3) The RADIO OUTPUT pin is brought to the OFF state. (4) The control input is inhibited (except the following). OFF INPUT ALARM/SLEEP TIME SET INPUT at the time setting enable mode . . No.2658-4/7 LM8562 5. Alarm The LM8562 contains two alarms on a 24-hour basis. Alarm 1 ..... Superposition of 600 Hz and 1 Hz Alarm 2 ..... Superposition of 1200 Hz and 1 Hz 6-minutes snooze The alarm output duration time is 59 minutes. The 59-minute duration counter is common to the alarm 1, alarm2, and sleep timer. 6. Time Setting, Dimmer The 3 level input RT-TIME SET/DIMMER INPUT pin provides the following functions. RT-TIME SET/DIMMER INPUT Pin Input VDD OPEN VSS Functions Time setting enable, normal display Time, alarm time, sleep timer duration time setting enable Time setting inhibit, normal display Time setting enable (except power-down mode) Time setting inhibit, dimmer display Display brightness 50 Hz mode: 1/24 duty 60 Hz mode: 1/20 duty . . . The 3-level input TIME-SET INPUT pin provides the following operations. TIME-SET INPUT Pin Input AC (50/60 Hz or more) VDD DC (20 ms min.) OPEN AC (50/60 Hz or more) VSS DC (20 ms min.) Setting Contents 1 Fast-up/down 2 Slow-up/down 7. 8. Operations Fast-up Slow-up No operation Fast-down Slow-down 50/60 Hz rate Immediately incremented/decremented ±1 and counted up/down at a 2 Hz rate 0.5 to 1.0 second later ON/OFF INPUT Pin The 3-level input ON/OFF INPUT pin acts on the ALM-1, 2 RADIO OUTPUT pins as shown below. Output Pin ON-State Condition ALM-1 OUTPUT Alarm 1 setting time = Current time Pause Conditions Snooze-in ALM-2 OUTPUT Alarm 2 setting time = Current time Snooze-in RADIO OUTPUT ON/OFF INPUT = VSS (ON-state indicator : ON state) — Sleep-in (Sleep indicator : ON state) — .. .. . .. .. . .. . .. . OFF-State Conditions ON/OFF INPUT = VSS ON/OFF INPUT = VDD Sleep-in 59 minutes after the alarm 1 is turned ON ALM-1 OUTPUT = VDD ON/OFF INPUT = VSS ON/OFF INPUT = VDD Sleep-in 59 minutes after the alarm 2 is turned ON ALM-2 OUTPUT = VDD ON/OFF INPUT = VDD Power-down mode Sleep-in (On-state indicator : OFF state) ON/OFF INPUT = VSS ON/OFF INPUT = VDD Power-down mode (Sleep indicator : OFF state) Sleep, Snooze Timer The 3-level input SLEEP/SNOOZE INPUT pin operates as shown below. SLEEP/SNOOZE INPUT Pin Input VDD (20 ms min.) OPEN VSS (20 ms min.) Operation Snooze-in & seconds display mode The alarm stops functioning for 6 to 7 minutes. Seconds display No operation Sleep mode The sleep counter is set to operate for 59 minutes. Counted down automatically at a 2 Hz rate 1.5 to 2.0 seconds later Fast/slow, up/down time setting available .. . .. No.2658-5/7 LM8562 9. 50/60 Hz INPUT Pin The LM8562 contains a Schmitt circuit so that a simple CR filter can be used to remove the noise of commercial frequency 50/60 Hz. 10. 12/24-Hour Mode, 50/60 Hz Select The 3-level input MODE SELECT pin provides the following combinations. MODE SELECT Pin Input VDD OPEN VSS Select 12-hour mode & 60 Hz 12-hour mode & 50 Hz 24-hour mode & 50 Hz Sample Application Circuit No.2658-6/7 LM8562 Block Diagram No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. Anyone purchasing any products described or contained herein for an above-mentioned use shall: 1 Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: 2 Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of December, 1997. Specifications and information herein are subject to change without notice. No.2658-7/7