HCC/HCF4514B HCC/HCF4515B 4-BIT LATCH/4-TO-16 LINE DECODER HCC/HCF4514B OUTPUT ”HIGH” ON SELECT HCC/HCF4515B OUTPUT ”LOW” ON SELECT . .. . .. QUIESCENT CURRENT SPECIFIED TO 20V FOR HCC DEVICE STROBED INPUT LATCH INHIBIT CONTROL INPUT CURRENT OF 100nA AT 18V AND 25°C FOR HCC DEVICE 100% TESTED FOR QUIESCENT CURRENT MEETS ALL REQUIREMENTS OF JEDEC TENTATIVE STANDARD N0. 13A, ”STANDARD SPECIFICATIONS FOR DESCRIPTION OF ”B” SERIES CMOS DEVICES” EY (Plastic Package) F (Ceramic Frit Seal Package) M1 (Micro Package) ORDER CODES : HCC45XXBF HCF45XXBEY HCF45XXBM1 PIN CONNECTIONS DESCRIPTION The HCC 4514B/HCC4515B (extended temperature range) and the HCF 4514B/HCF4515B (intermediate temperature range) are monolithic integrated circuits available in 24-lead dual in-line plastic or ceramic package and plastic micro package. The HCC/HCF4514B/4515B consisting of a 4-bit strobed latch and a 4 to 16 line decoder. The latches hold the last input data presented prior to the strobe transition from 1 to 0. Inhibit control allows all outputs to be placed at 0 (HCC/HCF4514B)or 1 (HCC/HCF4515B) regardless of the state ofthe data or strobe inputs. The decode truth table indicates all combinations of data inputs and appropriate selected outputs. June 1989 1/11 HCC/HCF4514B/4515B FUNCTIONAL DIAGRAM ABSOLUTE MAXIMUM RATINGS Symbol V DD * Parameter Supply Voltage : HC C Types H C F Types Value Unit – 0.5 to + 20 – 0.5 to + 18 V V – 0.5 to V DD + 0.5 V Vi Input Voltage II DC Input Current (any one input) ± 10 mA Pto t Total Power Dissipation (per package) Dissipation per Output Transistor for T o p = Full Package-temperature Range 200 mW 100 mW T op Operating Temperature : HCC Types H CF Types – 55 to + 125 – 40 to + 85 °C °C T stg Storage Temperature – 65 to + 150 °C Stresses above those listed under ”Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for external periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS Symbol V DD VI Top 2/11 Parameter Supply Voltage : H CC Types H C F Types Input Voltage Operating Temperature : HCC Types H CF Types Value Unit 3 to 18 3 to 15 V V 0 to V DD V – 55 to + 125 – 40 to + 85 °C °C HCC/HCF4514B/4515B LOGIC DIAGRAM AND TRUTH TABLE Strobe = 1 Dat a Inputs Inhibit D C B A Selected Output HCC/HCF 4514B = Logic 1 (High) HCC/HCF 4515B = Logic 0 (Low) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 0 1 0 1 S0 S1 S2 S3 0 0 0 0 0 0 0 0 1 1 1 1 0 0 1 1 0 1 0 1 S4 S5 S6 S7 0 0 0 0 1 1 1 1 0 0 0 0 0 0 1 1 0 1 0 1 S8 S9 S10 S11 0 0 0 0 1 1 1 1 1 1 1 1 0 0 1 1 0 1 0 1 S12 S13 S14 S15 1 X X X X All Outputs = 0, HCC/HCF 4514 B All Outputs = 1, HCC/HCF 4515 B WAVEFORMS Setup Time and Strobe Pulse Width. X = Don’t Care 1 = high 3/11 HCC/HCF4514B/4515B STATIC ELECTRICAL CHARACTERISTICS (over recommended operating conditions) Test Conditions Symbol IL V OH V OL V IH V IL I OH I OL Parameter Quiescent Current VI (V) 5 5 0.04 5 150 HCC 0/10 Types 0/15 10 10 0.04 10 300 15 20 0.04 20 600 0/20 20 100 0.08 100 3000 0/ 5 5 20 0.04 20 150 HCF 0/10 Types 0/15 10 40 0.04 40 300 0.04 80 Output Low Voltage 0/10 <1 10 9.95 9.95 9.95 0/15 <1 15 14.95 14.95 14.95 4.95 <1 5 0.05 0.05 0.05 <1 10 0.05 0.05 0.05 15/0 <1 15 0.05 0.05 0.05 0.5/4.5 <1 5 3.5 3.5 3.5 1/9 <1 10 7 7 7 1.5/13.5 < 1 15 11 4.5/0.5 <1 5 1.5 1.5 1.5 9/1 <1 10 3 3 3 13.5/1.5 < 1 15 2.5 HCC 0/ 5 Types 0/10 0/15 13.5 15 0/ 5 2.5 5 0/ 5 HCF Types 0/10 4.6 5 9.5 0/15 13.5 0/ 5 HCC 0/10 Types 0/15 0/ 5 11 4 5 – 2 4.6 5 9.5 10 4 V – 1.15 – 0.64 – 0.51 – 1 – 0.36 – 1.6 – 1.3 – 2.6 – 0.9 – 4.2 – 3.4 – 6.8 – 2.4 – 1.53 – 1.36 – 3.2 – 1.1 – 0.52 – 0.44 – 1 – 0.36 10 – 1.3 – 1.1 – 2.6 – 0.9 15 – 3.6 – 3.0 – 6.8 – 2.4 0.4 5 0.64 0.51 1 0.36 0.5 10 1.6 1.3 2.6 0.9 1.5 15 4.2 3.4 6.8 2.4 0.4 5 0.52 0.44 1 0.36 0.5 10 1.3 1.1 2.6 0.9 1.5 15 3.6 3.0 6.8 2.4 18 ± 0.1 ±10 – 5 ± 0.1 15 ± 0.3 ±10 mA mA ± 1 µA Any Input Input Capacitance Any Input V 4 – 1.6 – 3.2 HCC Types 0/18 V 11 5 –5 ± 0.3 7.5 * TLo w= – 55°C for HCC device : – 40°C for HCF device. * THigh= + 125°C for HCC device : + 85°C for HCF device. The Noise Margin for both ”1” and ”0” level is : 1V min. with VDD = 5V, 2V min. with VDD = 10V, 2.5 V min. with VDD = 15V. 4/11 V 5/0 0/ 5 µA 4.95 10/0 HCF 0/15 Types CI 4.95 Unit 600 5 Input Low Voltage Input Leakage Current 80 <1 HCF 0/10 Types 0/15 I IH , I IL 15 0/ 5 Input High Voltage Output Sink Current |I O | V D D T L o w* 25 °C T Hi g h * (µA) (V) Min. Max. Min. Typ. Max. Min. Max. 0/ 5 Output High Voltage Output Drive Current VO (V) Value ± 1 pF HCC/HCF4514B/4515B DYNAMIC ELECTRICAL CHARACTERISTICS (T amb = 25°C, CL = 50pF, R L = 200kΩ, all input rise and fall time = 20ns) Symbol t PHL , tP LH Test Conditions Parameter V D D (V) Min. Propagation Delay Time Strobe or Data Inhibit t T HL , t T HL Value Transition Time Typ. Max. 5 485 970 10 185 370 15 135 270 5 250 500 10 110 220 15 85 170 5 100 200 10 50 100 40 80 15 tW t se t u p Strobe Pulse Width Setup Time Typical Output Low (sink) Current Characteristics. 5 250 125 10 100 50 15 75 40 5 150 75 10 70 35 15 40 20 Unit ns ns ns ns ns Minimum Output Low (sink) Current Characteristics. 5/11 HCC/HCF4514B/4515B Typical Output High (source) Current Characteristics. Minimum Output High (source) Current Characteristics. Typical Strobe or Data Propagation Delay Time vs. Load Capacitance. Typical Inhibit Propagation Delay Time vs. Load Capacitance. Typical Transition Time vs. Load Capacitance. Typical Strobe or Data Propagation Delay Time vs. Supply Voltage. 6/11 HCC/HCF4514B/4515B Typical Power Dissipation vs. Frequency. TEST CIRCUITS Quiescent Device Current. Noise Immunity. Input Leakage Current. 7/11 HCC/HCF4514B/4515B Plastic DIP24 (0.25) MECHANICAL DATA mm DIM. MIN. TYP. inch MAX. MIN. TYP. a1 0.63 0.025 b 0.45 0.018 b1 0.23 b2 0.31 1.27 D E 0.009 0.012 0.050 32.2 15.2 16.68 1.268 0.598 0.657 e 2.54 0.100 e3 27.94 1.100 F MAX. 14.1 0.555 I 4.445 0.175 L 3.3 0.130 P043A 8/11 HCC/HCF4514B/4515B Ceramic DIP24 MECHANICAL DATA mm DIM. MIN. TYP. A inch MAX. MIN. TYP. 32.3 MAX. 1.272 B 13.05 13.36 0.514 0.526 C 3.9 5.08 0.154 0.200 D 3 E 0.5 e3 0.118 1.78 0.020 27.94 0.070 1.100 F 2.29 2.79 0.090 0.110 G 0.4 0.55 0.016 0.022 I 1.17 1.52 0.046 0.060 L 0.22 0.31 0.009 0.012 M 1.52 2.49 0.060 0.098 15.8 0.606 0.622 N1 P Q 4° (min.), 15° (max.) 15.4 5.71 0.225 P058C 9/11 HCC/HCF4514B/4515B SO24 MECHANICAL DATA mm DIM. MIN. inch TYP. MAX. A a1 MIN. TYP. MAX. 2.65 0.10 0.104 0.20 a2 0.004 0.007 2.45 0.096 b 0.35 0.49 0.013 0.019 b1 0.23 0.32 0.009 0.012 C 0.50 0.020 c1 45° (typ.) D 15.20 15.60 0.598 0.614 E 10.00 10.65 0.393 0.420 e 1.27 0.05 e3 13.97 0.55 F 7.40 7.60 0.291 0.299 L 0.50 1.27 0.19 0.050 S 8° (max.) L s e3 E D 13 1 12 F 24 10/11 b1 e a1 b A a2 C c1 HCC/HCF4514B/4515B Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express written approval of SGS-THOMSON Microelectonics. 1994 SGS-THOMSON Microelectronics - All Rights Reserved SGS-THOMSON Microelectronics GROUP OF COMPANIES Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A 11/11