LK115D00 SERIES VERY LOW DROP WITH INHIBIT VOLTAGE REGULATORS ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ VERY LOW DROPOUT VOLTAGE (0.2V TYP.) VERY LOW QUIESCENT CURRENT (TYP. 0.01µA IN OFF MODE, 280µA IN ON MODE) OUTPUT CURRENT UP TO 100 mA TWO LOGIC-CONTROLLED ELECTRONIC SHUTDOWNS OUTPUT VOLTAGES OF 2; 2.5; 3; 3.3; 4; 4.75; 4.85; 5; 5.5V INTERNAL CURRENT AND THERMAL LIMIT ONLY 2.2µF FOR STABILITY VOUT TOLLERANCE ± 3% AT 25 oC SUPPLY VOLTAGE REJECTION: 80 db (TYP.) TEMPERATURE RANGE: -40 TO 125 oC DESCRIPTION The LK115D00 series are very Low Drop regulators available in SO-8 package and in a wide range of output voltages. The very Low Drop voltage (0.2V) and the very low quiescent current (0.01µA in OFF MODE, SO-8 280µA in ON MODE) make them particularly suitable for Low Noise, Low Power applications and specially in battery powered systems. Both active HIGH and active LOW shutdown Logic Control are available (pin2 and 3). This means that when the device is used as a local regulator, it is possible to put a part of the board in standby, decreasing the total power consumption. It requires only a 2.2 µF capacitor for stability allowing space and cost saving. BLOCK DIAGRAM September 1998 1/10 LK115D00 SERIES ABSOLUTE MAXIMUM RATINGS Symbol Parameter Value Unit 20 V Vi DC Input Voltage Io Output Current Internally limited Pt ot Power Dissipation Internally limited T stg Storage Temperature Range To p Operating Junction Temperature Range - 40 to 150 o C - 40 to 125 o C CONNECTION DIAGRAM (top view) ORDERING NUMBERS Type LK115D20 LK115D25 LK115D30 LK115D33 LK115D40 LK115D47 LK115D48 LK115D50 LK115D55 (*) Available on request 2/10 Output Voltage 2V 2.5 V 3V 3.3 V 4V 4.75 V 4.85 V 5V 5.5 V LK115D00 SERIES TEST CIRCUITS: Supply Current (ON MODE) TEST CIRCUITS: Supply Current (OFF MODE) NOTE: The switch emulates the two possibilities to set the regulator in OFF mode. THRUTH TABLE ON/OFF (PIN 2) ON/OFF (PIN 3) STATUS H L ON H H OF F L L OF F L H NOT ALLO WED NOTES: Logic Levels are those defined in the electrical characteristics 3/10 LK115D00 SERIES ELECTRICAL CHARACTERISTICS FOR LK115D20 (refer to the test circuits, Tj = 25 oC, Ci = 0.1 µF, Co = 2.2 µF unless otherwise specified) Symbol Parameter Test Conditions Vo Output Voltage Io = 10 mA, Vi = 4 V o Io = 10 mA, Vi = 4 V, -40<Ta<125 C Io = 100 mA Min. Typ. Max. Unit 1.940 1.9 2 2.060 2.1 V V 120 200 Vi Operating Input Voltage I out Output Current Limit ∆V o Line Regulation Vi = 3 to 20 V, Io = 0.5 mA 2 10 mV ∆V o Load Regulation Vi = 3 V Io = 0.5 to 100 mA 4 20 mV Quiescent Current ON MODE Vi = 3 to 20 V Vi = 3 to 20 V Io = 0 mA Io = 100 mA 0.28 1.5 0.5 3 mA mA OFF MODE Vi = 3 to 20 V 0.01 2 µA Id 20 eN Output Noise Voltage Io = 5 mA Vi = 4 V ± 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Vd Dropout Voltage Io = 60 mA V Hlc ON/OFF Control (pin 2) Pin 3 to GND Pin 3 to GND V Llc ON/OFF Control (pin 3) Pin 2 to Vin Pin 2 to Vin CO Output Bypass Capacitance ESR = 0.5 to 10 Ω, Io = 0 to 100 mA SVR Supply Voltage Rejection 83 78 59 dB dB dB 44 µV 0.17 OFF ON OFF ON V mA V 0 2.4 0.5 V in V V Vi n 0.2 0 2 V in Vi n 2.4 V V µF 10 ELECTRICAL CHARACTERISTICS FOR LK115D25 (refer to the test circuits, Tj = 25 oC, Ci = 0.1 µF, Co = 2.2 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit 2.425 2.375 2.5 2.575 2.625 V V 20 120 200 V mA 2 10 mV 4 20 mV Io = 0 mA Io = 100 mA 0.28 1.5 0.5 3 mA mA Vi = 3.5 to 20 V 0.01 2 µA Vo Output Voltage Io = 10 mA, Vi = 4.5 V o Io = 10 mA, Vi = 4.5 V, -40<Ta<125 C Vi I out Operating Input Voltage Output Current Limit Io = 100 mA ∆V o Line Regulation Vi = 3.5 to 20 V, Io = 0.5 mA ∆V o Load Regulation Vi = 3.5 V Quiescent Current ON MODE Vi = 3.5 to 20 V Vi = 3.5 to 20 V Id OFF MODE Io = 0.5 to 100 mA eN Output Noise Voltage Io = 5 mA Vi = 4.5 V ± 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Vd Dropout Voltage Io = 60 mA V Hlc ON/OFF Control (pin 2) Pin 3 to GND Pin 3 to GND V Llc ON/OFF Control (pin 3) Pin 2 to Vin Pin 2 to Vin CO Output Bypass Capacitance ESR = 0.5 to 10 Ω, Io = 0 to 100 mA SVR 4/10 Supply Voltage Rejection OFF ON OFF ON 81 76 58 dB dB dB 55 µV 0.17 V 0 2.4 0.5 V in V V Vi n 0.2 0 V in Vi n 2.4 V V 2 10 µF LK115D00 SERIES ELECTRICAL CHARACTERISTICS FOR LK115D30 (refer to the test circuits, Tj = 25 oC, Ci = 0.1 µF, Co = 2.2 µF unless otherwise specified) Symbol Parameter Test Conditions Vo Output Voltage Io = 10 mA, Vi = 5 V o Io = 10 mA, Vi = 5 V, -40<Ta<125 C Io = 100 mA Vi Operating Input Voltage I out Output Current Limit ∆V o Line Regulation Vi = 4 to 20 V, ∆V o Load Regulation Vi = 4 V Io = 0.5 to 100 mA Quiescent Current ON MODE Vi = 4 to 20 V Vi = 4 to 20 V OFF MODE Id Max. Unit 3 3.090 3.150 V V 120 200 Io = 0.5 mA V mA 2 10 mV 4 20 mV Io = 0 mA Io = 100 mA 0.28 1.5 0.5 3 mA mA Vi = 4 to 20 V 0.01 2 µA eN Output Noise Voltage Vd Dropout Voltage Io = 60 mA V Hlc ON/OFF Control (pin 2) V Llc ON/OFF Control (pin 3) Pin 3 to GND Pin 3 to GND Pin 2 to Vin Pin 2 to Vin CO Output Bypass Capacitance Supply Voltage Rejection Typ. 20 Io = 5 mA Vi = 5 V ± 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz SVR Min. 2.910 2.850 79 74 57 66 dB dB dB µV 0.17 OFF ON OFF ON ESR = 0.5 to 10 Ω, Io = 0 to 100 mA 0 2.4 V in 0.2 0 2 V 0.5 V in V in V in 2.4 V V V V µF 10 ELECTRICAL CHARACTERISTICS FOR LK115D33 (refer to the test circuits, Tj = 25 oC, Ci = 0.1 µF, Co = 2.2 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit 3.2 3.135 3.3 3.4 3.465 V V 20 120 200 V mA 2 10 mV 4 20 mV Io = 0 mA Io = 100 mA 0.28 1.5 0.5 3 mA mA Vi = 4.3 to 20 V 0.01 2 µA Vo Output Voltage Io = 10 mA, Vi = 5.3 V o Io = 10 mA, Vi = 5.3 V, -40<Ta<125 C Vi I out Operating Input Voltage Output Current Limit Io = 100 mA ∆V o Line Regulation Vi = 4.3 to 20 V, Io = 0.5 mA ∆V o Load Regulation Vi = 4.3 V Quiescent Current ON MODE Vi = 4.3 to 20 V Vi = 4.3 to 20 V Id OFF MODE Io = 0.5 to 100 mA eN Output Noise Voltage Io = 5 mA Vi = 5.3 V ± 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Vd Dropout Voltage Io = 60 mA V Hlc ON/OFF Control (pin 2) Pin 3 to GND Pin 3 to GND V Llc ON/OFF Control (pin 3) Pin 2 to Vin Pin 2 to Vin CO Output Bypass Capacitance ESR = 0.5 to 10 Ω, Io = 0 to 100 mA SVR Supply Voltage Rejection OFF ON OFF ON 79 74 57 dB dB dB 72.6 µV 0.17 V 0 2.4 0.5 V in V V Vi n 0.2 0 V in Vi n 2.4 V V 2 10 µF 5/10 LK115D00 SERIES ELECTRICAL CHARACTERISTICS FOR LK115D40 (refer to the test circuits, Tj = 25 oC, Ci = 0.1 µF, Co = 2.2 µF unless otherwise specified) Symbol Parameter Test Conditions Vo Output Voltage Io = 10 mA, Vi = 6 V o Io = 10 mA, Vi = 6 V, -40<Ta<125 C Io = 100 mA Min. Typ. Max. Unit 3.880 3.8 4 4.120 4.2 V V 120 200 Vi Operating Input Voltage I out Output Current Limit ∆V o Line Regulation Vi = 5 to 20 V, Io = 0.5 mA 3 15 mV ∆V o Load Regulation Vi = 5 V Io = 0.5 to 100 mA 4 20 mV Quiescent Current ON MODE Vi = 5 to 20 V Vi = 5 to 20 V Io = 0 mA Io = 100 mA 0.28 1.5 0.5 3 mA mA OFF MODE Vi = 5 to 20 V 0.01 2 µA Id 20 eN Output Noise Voltage Io = 5 mA Vi = 5 V ± 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Vd Dropout Voltage Io = 60 mA V Hlc ON/OFF Control (pin 2) Pin 3 to GND Pin 3 to GND V Llc ON/OFF Control (pin 3) Pin 2 to Vin Pin 2 to Vin CO Output Bypass Capacitance ESR = 0.5 to 10 Ω, Io = 0 to 100 mA SVR Supply Voltage Rejection 77 72 56 dB dB dB 88 µV 0.17 OFF ON OFF ON V mA V 0 2.4 0.5 V in V V Vi n 0.2 0 2 V in Vi n 2.4 V V µF 10 ELECTRICAL CHARACTERISTICS FOR LK115D47 (refer to the test circuits, Tj = 25 oC, Ci = 0.1 µF, Co = 2.2 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit 4.607 4.513 4.75 4.892 4.987 V V 20 120 200 V mA 3 15 mV 4 20 mV Io = 0 mA Io = 100 mA 0.28 1.5 0.5 3 mA mA Vi = 5.8 to 20 V 0.01 2 µA Vo Output Voltage Io = 10 mA, Vi = 6.8 V o Io = 10 mA, Vi = 6.8 V, -40<Ta<125 C Vi I out Operating Input Voltage Output Current Limit Io = 100 mA ∆V o Line Regulation Vi = 5.8 to 20 V, Io = 0.5 mA ∆V o Load Regulation Vi = 5.8 V Quiescent Current ON MODE Vi = 5.8 to 20 V Vi = 5.8 to 20 V Id OFF MODE Io = 0.5 to 100 mA eN Output Noise Voltage Io = 5 mA Vi = 6.8 V ± 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Vd Dropout Voltage Io = 60 mA V Hlc ON/OFF Control (pin 2) Pin 3 to GND Pin 3 to GND V Llc ON/OFF Control (pin 3) Pin 2 to Vin Pin 2 to Vin CO Output Bypass Capacitance ESR = 0.5 to 10 Ω, Io = 0 to 100 mA SVR 6/10 Supply Voltage Rejection OFF ON OFF ON 75 70 55 dB dB dB 104.5 µV 0.17 V 0 2.4 0.5 V in V V Vi n 0.2 0 V in Vi n 2.4 V V 2 10 µF LK115D00 SERIES ELECTRICAL CHARACTERISTICS FOR LK115D48 (refer to the test circuits, Tj = 25 oC, Ci = 0.1 µF, Co = 2.2 µF unless otherwise specified) Symbol Parameter Test Conditions Vo Output Voltage Io = 10 mA, Vi = 6.9 V o Io = 10 mA, Vi = 6.9 V, -40<Ta<125 C Io = 100 mA Vi Operating Input Voltage I out Output Current Limit ∆V o Line Regulation Vi = 5.9 to 20 V, ∆V o Load Regulation Vi = 5.9 V Quiescent Current ON MODE Vi = 5.9 to 20 V Vi = 5.9 to 20 V Id Max. Unit 4.705 4.607 4.85 4.966 5.093 V V 120 200 20 Io = 0.5 mA Io = 0 mA Io = 100 mA Vi = 5.9 to 20 V eN Output Noise Voltage Io = 5 mA Vi = 6.9 V ± 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Vd Dropout Voltage Io = 60 mA V Hlc ON/OFF Control (pin 2) Pin 3 to GND Pin 3 to GND V Llc ON/OFF Control (pin 3) Pin 2 to Vin Pin 2 to Vin CO Output Bypass Capacitance ESR = 0.5 to 10 Ω, Io = 0 to 100 mA Supply Voltage Rejection Typ. Io = 0.5 to 100 mA OFF MODE SVR Min. 3 15 mV 4 20 mV 0.28 1.5 0.5 3 mA mA 0.01 2 µA 75 70 55 dB dB dB 106.7 µV 0.17 OFF ON OFF ON V mA V 0 2.4 0.5 V in V V Vi n 0.2 0 2 V in Vi n 2.4 V V µF 10 ELECTRICAL CHARACTERISTICS FOR LK115D50 (refer to the test circuits, Tj = 25 oC, Ci = 0.1 µF, Co = 2.2 µF unless otherwise specified) Symbol Parameter Test Conditions Min. Typ. Max. Unit 4.85 4.75 5 5.15 5.25 V V 20 120 200 V mA 3 15 mV 4 20 mV Io = 0 mA Io = 100 mA 0.28 1.5 0.5 3 mA mA Vi = 6 to 20 V 0.01 2 µA Vo Output Voltage Io = 10 mA, Vi = 7 V o Io = 10 mA, Vi = 7 V, -40<Ta<125 C Vi I out Operating Input Voltage Output Current Limit Io = 100 mA ∆V o Line Regulation Vi = 6 to 20 V, Io = 0.5 mA ∆V o Load Regulation Vi = 6 V Quiescent Current ON MODE Vi = 6 to 20 V Vi = 6 to 20 V OFF MODE Id Io = 0.5 to 100 mA eN Output Noise Voltage Io = 5 mA Vi = 7 V ± 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz Vd Dropout Voltage Io = 60 mA V Hlc ON/OFF Control (pin 2) Pin 3 to GND Pin 3 to GND V Llc ON/OFF Control (pin 3) Pin 2 to Vin Pin 2 to Vin CO Output Bypass Capacitance ESR = 0.5 to 10 Ω, Io = 0 to 100 mA SVR Supply Voltage Rejection OFF ON OFF ON 75 70 55 dB dB dB 110 µV 0.17 V 0 2.4 0.5 V in V V Vi n 0.2 0 V in Vi n 2.4 V V 2 10 µF 7/10 LK115D00 SERIES ELECTRICAL CHARACTERISTICS FOR LK115D55 (refer to the test circuits, Tj = 25 oC, Ci = 0.1 µF, Co = 2.2 µF unless otherwise specified) Symbol Parameter Test Conditions Vo Output Voltage Io = 10 mA, Vi = 7.5 V o Io = 10 mA, Vi = 7.5 V, -40<Ta<125 C Io = 100 mA Vi Operating Input Voltage I out Output Current Limit ∆V o Line Regulation Vi = 6.5 to 20 V, ∆V o Load Regulation Vi = 6.5 V Quiescent Current ON MODE Vi = 6.5 to 20 V Vi = 6.5 to 20 V Id OFF MODE Unit 5.335 5.225 5.5 5.665 5.775 V V 120 200 Io = 0.5 mA Io = 0 mA Io = 100 mA Vi = 6.5 to 20 V Output Noise Voltage Vd Dropout Voltage Io = 60 mA V Hlc ON/OFF Control (pin 2) Pin 3 to GND Pin 3 to GND V Llc ON/OFF Control (pin 3) Pin 2 to Vin Pin 2 to Vin CO Output Bypass Capacitance ESR = 0.5 to 10 Ω, Io = 0 to 100 mA 8/10 Max. Io = 0.5 to 100 mA eN Supply Voltage Rejection Typ. 20 Io = 5 mA Vi = 7.5 V ± 1V f = 120 Hz f = 1 KHz f = 10 KHz B = 10 Hz to 100 KHz SVR Min. OFF ON OFF ON V mA 3 15 mV 4 20 mV 0.28 1.5 0.5 3 mA mA 0.01 2 µA 74 69 55 dB dB dB 121 µV 0.17 V 0 2.4 0.5 V in V V Vi n 0.2 0 2 V in Vi n 2.4 V V 10 µF LK115D00 SERIES SO-8 MECHANICAL DATA mm DIM. MIN. TYP. A a1 inch MAX. MIN. TYP. 1.75 0.1 0.068 0.25 a2 MAX. 0.003 0.009 1.65 0.064 a3 0.65 0.85 0.025 0.033 b 0.35 0.48 0.013 0.018 b1 0.19 0.25 0.007 0.010 C 0.25 0.5 0.010 0.019 c1 45 (typ.) D 4.8 5.0 0.188 0.196 E 5.8 6.2 0.228 0.244 e 1.27 0.050 e3 3.81 0.150 F 3.8 4.0 0.14 0.157 L 0.4 1.27 0.015 0.050 M S 0.6 0.023 8 (max.) 0016023 9/10 LK115D00 SERIES Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specification mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a trademark of STMicroelectronics 1998 STMicroelectronics – Printed in Italy – All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - France - Germany - Italy - Japan - Korea - Malaysia - Malta - Mexico - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A. . 10/10