M74HC245 OCTAL BUS TRANSCEIVER WITH 3 STATE OUTPUTS (NON INVERTED) ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 10ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC = 4µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = V NIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 6mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 245 DESCRIPTION The M74HC245 is an advanced high-speed CMOS OCTAL BUS TRANSCEIVER (3-STATE) fabricated with silicon gate C2MOS technology. This IC is intended for two-way asynchronous communication between data buses, and the direction of data transmission is determined by DIR input. The enable input G can be used to DIP SOP TSSOP ORDER CODES PACKAGE TUBE DIP SOP TSSOP M74HC245B1R M74HC245M1R T&R M74HC245RM13TR M74HC245TTR disable the device so that the buses are effectively isolated. All inputs are equipped with protection circuits against static discharge and transient excess voltage. All floating bus terminals during High Z State must be held HIGH or LOW. PIN CONNECTION AND IEC LOGIC SYMBOLS July 2001 1/10 M74HC245 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL 1 2, 3, 4, 5, 6, 7, 8, 9 18, 17, 16, 15, 14, 13, 12, 11 19 10 20 DIR A1 to A8 Directional Control Data Inputs/Outputs B1 to B8 Data Inputs/Outputs G GND VCC NAME AND FUNCTION Output Enable Input Ground (0V) Positive Supply Voltage TRUTH TABLE INPUTS FUNCTION OUTPUT G DIR A BUS B BUS Yn L L H L H X OUTPUT INPUT Z INPUT OUTPUT Z A=B B=A Z X : Don’t Care Z : High Impedance ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Value Supply Voltage Unit -0.5 to +7 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 35 mA VI DC Input Voltage VO DC Output Voltage IIK ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) V ± 70 mA 500(*) mW -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/ °C from 65°C to 85°C RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage VI Input Voltage VO Output Voltage Top Operating Temperature Input Rise and Fall Time tr, tf 2/10 Value Unit 2 to 6 V 0 to VCC V 0 to VCC V -55 to 125 °C VCC = 2.0V 0 to 1000 ns VCC = 4.5V 0 to 500 ns VCC = 6.0V 0 to 400 ns M74HC245 DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH VOL II IOZ ICC Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current High Impedance Output Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 4.5 6.0 2.0 4.5 6.0 Typ. Max. 1.5 3.15 4.2 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 3.15 4.2 0.5 1.35 1.8 Max. 1.5 3.15 4.2 0.5 1.35 1.8 V 0.5 1.35 1.8 2.0 IO=-20 µA 1.9 2.0 1.9 1.9 4.5 IO=-20 µA 4.4 4.5 4.4 4.4 6.0 IO=-20 µA 5.9 6.0 5.9 5.9 4.5 IO=-6.0 mA 4.18 4.31 4.13 4.10 5.68 Unit V V 6.0 IO=-7.8 mA 2.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=20 µA 0.0 0.1 0.1 0.1 6.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=6.0 mA 0.17 0.26 0.33 0.40 6.0 IO=7.8 mA 0.18 0.26 0.33 0.40 6.0 VI = VCC or GND ± 0.1 ±1 ±1 µA 6.0 VI = VIH or VIL VO = VCC or GND ± 0.5 ±5 ± 10 µA 6.0 VI = VCC or GND 4 40 80 µA 5.8 5.63 5.60 V 3/10 M74HC245 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time tPZL tPZH High Impedance Output Enable Time tPLZ tPHZ High Impedance Output Disable Time VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 Value TA = 25°C CL (pF) Min. 50 50 150 50 RL = 1 KΩ 150 RL = 1 KΩ 50 RL = 1 KΩ Typ. Max. 25 7 6 33 12 10 48 16 14 48 16 14 63 21 18 37 17 15 60 12 10 90 18 15 120 24 20 150 30 26 180 36 31 150 30 26 -40 to 85°C -55 to 125°C Min. Min. Max. 75 19 13 115 23 20 150 30 26 190 38 32 225 45 38 190 38 32 Unit Max. 90 18 15 135 27 23 180 36 31 225 45 38 270 54 46 225 45 38 ns ns ns ns ns ns CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter CIN Input Capacitance CI/OUT Output Capacitance Power Dissipation Capacitance (note 1) CPD Value TA = 25°C VCC (V) Min. -40 to 85°C -55 to 125°C Min. Min. Max. Unit Typ. Max. DIR, G 5 10 An, Bn 13 pF 39 pF 10 Max. 10 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = C PD x VCC x fIN + ICC/8 (per circuit) 4/10 M74HC245 TEST CIRCUIT TEST tPLH, tPHL SWITCH Open tPZL, tPLZ VCC tPZH, tPHZ GND CL = 50pF/150pF or equivalent (includes jig and probe capacitance) R1 = 1KΩ or equivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM 1: PROPAGATION DELAY TIME (f=1MHz; 50% duty cycle) 5/10 M74HC245 WAVEFORM 2 : OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) 6/10 M74HC245 Plastic DIP-20 (0.25) MECHANICAL DATA mm. inch DIM. MIN. a1 0.254 B 1.39 TYP MAX. MIN. TYP. MAX. 0.010 1.65 0.055 0.065 b 0.45 0.018 b1 0.25 0.010 D 25.4 1.000 E 8.5 0.335 e 2.54 0.100 e3 22.86 0.900 F 7.1 0.280 I 3.93 0.155 L Z 3.3 0.130 1.34 0.053 P001J 7/10 M74HC245 SO-20 MECHANICAL DATA mm. inch DIM. MIN. TYP A a1 MAX. MIN. TYP. 2.65 0.1 0.104 0.2 a2 MAX. 0.004 0.008 2.45 0.096 b 0.35 0.49 0.014 0.019 b1 0.23 0.32 0.009 0.012 C 0.5 0.020 c1 45° (typ.) D 12.60 13.00 0.496 0.512 E 10.00 10.65 0.393 0.419 e 1.27 0.050 e3 11.43 0.450 F 7.40 7.60 0.291 0.300 L 0.50 1.27 0.020 0.050 M S 0.75 0.029 8° (max.) PO13L 8/10 M74HC245 TSSOP20 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. A MIN. TYP. MAX. 1.2 A1 0.05 A2 0.8 b 0.047 0.15 0.002 0.004 0.006 1.05 0.031 0.039 0.041 0.19 0.30 0.007 0.012 c 0.09 0.20 0.004 0.0089 D 6.4 6.5 6.6 0.252 0.256 0.260 E 6.2 6.4 6.6 0.244 0.252 0.260 E1 4.3 4.4 4.48 0.169 0.173 0.176 1 e 0.65 BSC K 0° L 0.45 A 0.0256 BSC 0.60 8° 0° 0.75 0.018 8° 0.024 0.030 A2 A1 b K e L E c D E1 PIN 1 IDENTIFICATION 1 0087225C 9/10 M74HC245 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com 10/10 This datasheet has been download from: www.datasheetcatalog.com Datasheets for electronics components.