STMICROELECTRONICS M74HC4024B1R

M54HC4024
M74HC4024
7 STAGE BINARY COUNTER
.
.
.
.
.
.
.
.
HIGH SPEED
tPD = 13 ns (TYP.) AT VCC = 5 V
LOW POWER DISSIPATION
ICC = 4 µA (MAX.) AT TA = 25° C
HIGH NOISE IMMUNITY
VNIH = VNIL = 28 % VCC (MIN.)
OUTPUT DRIVE CAPABILITY
10 LSTTL LOADS
SYMMETRICAL OUTPUT IMPEDANCE
|IOH|= IOL = 4 mA (MIN.)
BALANCED PROPAGATION DELAYS
tPLH = tPHL
WIDE OPERATING VOLTAGE RANGE
VCC (OPR) = 2 V TO 6 V
PIN AND FUNCTION COMPATIBLE
WITH 4024B
B1R
(Plastic Package)
F1R
(Ceramic Package)
M1R
(Micro Package)
C1R
(Chip Carrier)
ORDER CODES :
M54HC4024F1R
M74HC4024M1R
M74HC4024B1R
M74HC4024C1R
PIN CONNECTIONS (top view)
DESCRIPTION
The M54/74HC4024 is a high speed CMOS 7STAGE BINARY COUNTER fabricated in silicon
gate C2MOS technology. It has the same high
speed performance of LSTTL combined with true
CMOS low power consumption. The HC4024 is a 7
stage Counter. This devices is incremented on the
falling edge (negative transition) of the input clock,
and all its outputs are reset to a low level by applying
a logical high on their reset input. All inputs are
equipped with protection circuits against static discharge and transient excess voltage.
October 1992
NC =
No Internal
Connection
1/11
M54/M74HC4024
INPUT AND OUTPUT EQUIVALENT CIRCUIT
TRUTH TABLE
CLOCK
CLEAR
OUTPUT STATE
X
H
ALL OUTPUTS = ”L”
L
L
NO CHANGE
ADVANCE TO NEXT STATE
X: DON’T CARE
LOGIC DIAGRAM
2/11
M54/ M74HC4024
PIN DESCRIPTION
PIN No
SYMBOL
1
CLOCK
2
RESET
12, 11, 9, 6,
5, 4, 3
Q1 to Q7
8, 10, 13
NC
7
14
GND
V CC
IEC LOGIC SYMBOL
NAME AND FUNCTION
Clock Input (HIGH to
LOW, Edge-triggered)
Reset Input (Active
HIGH)
Parallel Outputs
Not Connected
Ground (0V)
Positive Supply Voltage
ABSOLUTE MAXIMUM RATINGS
Symbol
VCC
Parameter
Supply Voltage
Value
-0.5 to +7
Unit
V
VI
DC Input Voltage
-0.5 to VCC + 0.5
V
VO
IIK
DC Output Voltage
DC Input Diode Current
-0.5 to VCC + 0.5
± 20
V
mA
IOK
DC Output Diode Current
± 20
mA
DC Output Source Sink Current Per Output Pin
DC VCC or Ground Current
± 25
± 50
mA
mA
500 (*)
mW
IO
ICC or IGND
PD
Power Dissipation
Tstg
TL
Storage Temperature
Lead Temperature (10 sec)
-65 to +150
300
o
o
C
C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied.
(*) 500 mW: ≅ 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC
RECOMMENDED OPERATING CONDITIONS
Symbol
VCC
Parameter
Supply Voltage
VI
Input Voltage
VO
Top
Output Voltage
Operating Temperature: M54HC Series
M74HC Series
tr, tf
Input Rise and Fall Time
Value
2 to 6
Unit
V
0 to VCC
V
0 to VCC
-55 to +125
-40 to +85
VCC = 2 V
0 to 1000
VCC = 4.5 V
VCC = 6 V
0 to 500
0 to 400
V
C
o
C
o
ns
3/11
M54/M74HC4024
DC SPECIFICATIONS
Test Conditions
Symbol
VIH
V IL
Parameter
High Level Input
Voltage
Low Level Input
Voltage
Value
VCC
(V)
TA = 25 oC
54HC and 74HC
Min. Typ. Max.
2.0
1.5
1.5
1.5
4.5
6.0
3.15
4.2
3.15
4.2
3.15
4.2
High Level
Output Voltage
0.5
0.5
0.5
4.5
1.35
1.35
1.35
2.0
4.5
6.0
4.5
VOL
Low Level Output
Voltage
6.0
2.0
4.5
6.0
4.5
6.0
II
ICC
4/11
Input Leakage
Current
Quiescent Supply
Current
6.0
6.0
1.8
1.8
Unit
V
2.0
6.0
V OH
-40 to 85 oC -55 to 125 oC
74HC
54HC
Min. Max. Min. Max.
V
1.8
1.9
2.0
1.9
1.9
VI =
IO=-20 µA
VIH
or
V IL IO=-4.0 mA
4.4
5.9
4.5
6.0
4.4
5.9
4.4
5.9
4.18
4.31
4.13
4.10
IO=-5.2 mA
5.68
5.8
0.0
5.63
5.60
V
VI =
IO= 20 µA
VIH
or
V IL IO= 4.0 mA
0.1
0.1
0.1
0.0
0.1
0.1
0.1
0.0
0.17
0.1
0.26
0.1
0.33
0.1
0.40
IO= 5.2 mA
0.18
V
0.26
0.33
0.40
VI = VCC or GND
±0.1
±1
±1
µA
VI = VCC or GND
4
40
80
µA
M54/ M74HC4024
AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns)
Test Conditions
Value
Symbol
Parameter
VCC
(V)
TA = 25 oC
54HC and 74HC
Min. Typ. Max.
tTLH
tTHL
Output Transition
Time
2.0
30
75
95
110
4.5
6.0
8
7
15
13
19
16
22
19
tPLH
tPHL
Propagation
Delay Time
(Qn - Qn + 1)
2.0
24
60
75
90
4.5
6
12
15
18
tPLH
tPHL
Propagation
Delay Time
Clock - Q1
tPHL
Propagation
Delay Time
(CLEAR - Qn)
fMAX
Maximum Clock
Frequency
tW(H)
tW(L)
Minimum Pulse
Width (CLOCK)
tW(H)
Minimum Pulse
Width (CLEAR)
tREM
CIN
CPD (*)
Minimum
Removal Time
Input Capacitance
Power Dissipation
Capacitance
-40 to 85 oC -55 to 125 oC
74HC
54HC
Min. Max. Min. Max.
6.0
5
10
13
15
2.0
60
120
150
180
4.5
6.0
15
13
24
20
30
26
36
31
2.0
60
120
150
180
4.5
6.0
15
13
24
20
30
26
36
31
2.0
8
17
7
5.6
4.5
6.0
42
49
67
79
34
40
28
34
ns
ns
ns
ns
ns
2.0
24
75
95
110
4.5
6.0
6
5
15
13
19
16
22
19
2.0
32
75
95
110
4.5
6.0
8
7
15
13
19
16
22
19
2.0
4.5
25
5
30
6
40
8
6.0
5
5
7
10
10
10
5
34
Unit
ns
ns
ns
pF
pF
(*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load.
(Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD •VCC •fIN + ICC
5/11
M54/M74HC4024
SWITCHING CHARACTERISTICS TEST WAVEFORM
TEST CIRCUIT ICC (Opr.)
INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERISTICS TEST.
6/11
M54/ M74HC4024
Plastic DIP14 MECHANICAL DATA
mm
DIM.
MIN.
a1
0.51
B
1.39
TYP.
inch
MAX.
MIN.
TYP.
MAX.
0.020
1.65
0.055
0.065
b
0.5
0.020
b1
0.25
0.010
D
20
0.787
E
8.5
0.335
e
2.54
0.100
e3
15.24
0.600
F
7.1
0.280
I
5.1
0.201
L
Z
3.3
1.27
0.130
2.54
0.050
0.100
P001A
7/11
M54/M74HC4024
Ceramic DIP14/1 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
inch
MAX.
MIN.
TYP.
MAX.
A
20
0.787
B
7.0
0.276
D
E
3.3
0.130
0.38
e3
0.015
15.24
0.600
F
2.29
2.79
0.090
0.110
G
0.4
0.55
0.016
0.022
H
1.17
1.52
0.046
0.060
L
0.22
0.31
0.009
0.012
M
1.52
2.54
0.060
0.100
N
P
Q
10.3
7.8
8.05
5.08
0.406
0.307
0.317
0.200
P053C
8/11
M54/ M74HC4024
SO14 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
A
a1
inch
MAX.
MIN.
TYP.
1.75
0.1
0.068
0.2
a2
MAX.
0.003
0.007
1.65
0.064
b
0.35
0.46
0.013
0.018
b1
0.19
0.25
0.007
0.010
C
0.5
0.019
c1
45° (typ.)
D
8.55
E
5.8
8.75
0.336
6.2
0.228
0.344
0.244
e
1.27
0.050
e3
7.62
0.300
F
3.8
4.0
0.149
0.157
G
4.6
5.3
0.181
0.208
L
0.5
1.27
0.019
0.050
M
S
0.68
0.026
8° (max.)
P013G
9/11
M54/M74HC4024
PLCC20 MECHANICAL DATA
mm
DIM.
MIN.
TYP.
inch
MAX.
MIN.
TYP.
MAX.
A
9.78
10.03
0.385
0.395
B
8.89
9.04
0.350
0.356
D
4.2
4.57
0.165
0.180
d1
2.54
0.100
d2
0.56
0.022
E
7.37
8.38
0.290
0.330
e
1.27
0.050
e3
5.08
0.200
F
0.38
0.015
G
0.101
0.004
M
1.27
0.050
M1
1.14
0.045
P027A
10/11
M54/ M74HC4024
Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.
 1994 SGS-THOMSON Microelectronics - All Rights Reserved
SGS-THOMSON Microelectronics GROUP OF COMPANIES
Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A
11/11