TC7SBD384FU TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC7SBD384FU Single Bus Switch with Level Shifting The TC7SBD384FU provides single bit of high-speed TTL-compatible switching. The low on resistance of the switch allows connections to be made with minimal propagation delay. The device is organized as just 1-bit low-impedance switch with output-enable (OE) input. When OE is low, the switch is on and data can flow from port A to port B, or vice versa. When OE is high, the switch is open and a high-impedance state exists between the two ports. The internal diode which adds to power supply line is enable to realize the shift of signal level from 5 V to 3.3 V. (Note 1) All inputs are equipped with protection circuits against static discharge. Weight: 0.006 g (typ.) Features • Operating voltage: VCC = 4.5~5.5 V • High speed operation: tpd = 0.25 ns (max) • Low on resistance: RON = 5 Ω (typ.) • ESD performance: Machine model > ±200 V Human body model > ±2000 V • TTL level input (control input) • Package: USV Note 1: In case that over-shoot noise is detected, this device should be used with clamp diode to prevent the next stage device from over-stress. Pin Assignment (top view) VCC 5 OE 4 JH 1 A 2 B 3 GND 1 2001-12-04 TC7SBD384FU Truth Table Input Function OE L A port = B port H Disconnect System Diagram A B OE Maximum Ratings Characteristics Symbol Rating Unit Power supply range VCC −0.5~7.0 V DC input voltage VIN −0.5~7.0 V DC switch voltage VS −0.5~7.0 V Input diode current IIK −50 mA Continuous channel current IS 128 mA Power dissipation PD 200 mW DC VCC/GND current ICC/IGND ±100 mA Storage temperature Tstg −65~150 °C Symbol Rating Unit Supply voltage VCC 4.5~5.5 V Input voltage VIN 0~5.5 V Switch voltage VS 0~5.5 V Operating temperature Topr −40~85 °C Input rise and fall time dt/dv 0~10 ns/V Recommended Operating Conditions Characteristics 2 2001-12-04 TC7SBD384FU Electrical Characteristics DC Characteristics (Ta = −40~85°C) Characteristics Min Typ. (Note 2) Max 4.5~5.5 2.0 4.5~5.5 0.8 4.5~5.5 ±1.0 µA 0 ±1.0 µA 4.5~5.5 ±1.0 µA IIS = 30 mA 4.5 5 7 IIS = 64 mA 4.5 5 7 4.5 35 50 Switch ON 5.5 1.5 mA Switch OFF 5.5 10 µA 5.5 2.5 mA Symbol Test Condition “H” level VIH “L” level VIL Input voltage High-level output voltage Input leakage current VOH IIN Power off leakage current Quiescent supply current VIN = 0~5.5 V A, B, OE = 0~5.5 V ISZ A, B = 0~5.5 V, OE = VCC ON resistance (Note 3) Figure 4 IOFF Off-state leakage current (switch off) VCC (V) RON VIS = 0 V VIS = 2.4 V, IIS = 15 mA ICC VIN = VCC or GND, IOUT = 0 ∆ICC VIN = 3.4 V (one input) Unit V Ω Note 2: Typical values are at VCC = 5 V and Ta = 25°C. Note 3: Measured by the voltage drop between A and B pins at the indicated current through the switch. On resistance is determined by the lower of the voltages on the two (A or B) pins. AC Characteristics (Ta = −40~85°C) Characteristics Symbol Propagation delay time tpLH (bus to bus) tpHL Output enable time tpZL Test Condition Min Max Unit 4.5 0.25 ns Figure 1, Figure 3 4.5 4.5 ns Figure 1, Figure 3 4.5 4.5 ns Figure 1, Figure 2 VCC (V) (Note 4) tpZH Output disable time tpLZ tpHZ Note 4: This parameter is guaranteed by design but is not tested. The bus switch contributes no propagation delay other than the RC delay of the typical on resistance of the switch and the 50 pF load capacitance, when driven by an ideal voltage the source (zero output impedance). Capacitive Characteristics (Ta = 25°C) Characteristics Symbol Control pin input capacitance CIN Switch terminal capacitance CI/O Test Condition OE = VCC VCC (V) Typ. Unit (Note 5) 5.0 3 pF (Note 5) 5.0 10 pF Note 5: This item is guaranteed by design. 3 2001-12-04 TC7SBD384FU AC Test Circuit RL Switch Open 7.0 V GND Measure RL CL Output CL = 50 pF RL = 500 Ω Parameter Switch tpLH, tpHL Open tpLZ, tpZL 7.0 V tpHZ, tpZH Open Figure 1 AC Waveform tr 2.5 ns tf 2.5 ns 3.0 V 90% 1.5 V Input (A, B) 10% GND VOH Output (B, A) 1.5 V tpLH Figure 2 VOL tpHL tpLH, tpHL tf 2.5 ns tr 2.5 ns 3.0 V 90% 1.5 V Output Enable ( OE ) 10% tpLZ GND tpZL 3.5 V Output (A, B) Low to Off to Low 1.5 V tpHZ VOL + 0.3 V VOL tpZH VOH VOH − 0.3 V Output (A, B) High to Off to High 1.5 V GND Outputs enabled Figure 3 Outputs disabled Outputs enabled tpLZ, tpHZ, tpZL, tpZH 4 2001-12-04 TC7SBD384FU VOH – VCC Characteristics (typ.) 4.5 4.0 100 µA 3.5 6 mA 12 mA (V) Ta = 85°C High-level output voltage VOH High-level output voltage VOH (V) 4.5 24 mA 3.0 2.5 2.0 1.5 4.50 4.75 5.00 5.25 Power supply voltage VCC 5.50 Ta = 25°C 4.0 100 µA 3.0 2.5 2.0 1.5 4.50 5.75 6 mA 12 mA 24 mA 3.5 4.75 5.00 5.25 Power supply voltage (V) VCC 5.50 5.75 (V) High-level output voltage VOH (V) 4.5 Ta = 0°C 4.0 100 µA 3.5 6 mA 12 mA 24 mA 3.0 2.5 2.0 1.5 4.50 4.75 5.00 5.25 Power supply voltage VCC 5.50 5.75 (V) Figure 4 5 2001-12-04 TC7SBD384FU Package Dimensions Weight: 0.006 g (typ.) 6 2001-12-04 TC7SBD384FU RESTRICTIONS ON PRODUCT USE 000707EBA • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc.. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this document shall be made at the customer’s own risk. • The products described in this document are subject to the foreign exchange and foreign trade laws. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any intellectual property or other rights of TOSHIBA CORPORATION or others. • The information contained herein is subject to change without notice. 7 2001-12-04