ARG P10D THR U ARG P10M Fast Soft-Recovery Controlled Avalanche Rectifiers Voltage Range 200 to 1000 Volts DO -41 Features High tem perature m etallurgically bonded constructed Plastic m aterial used carries Underwriters Laboratory Classification 94V-0 G lass passivated cavity-free junction High m axim um operating tem perature Low leakage current Excellent stability G uaranteed avalanche energy absorption capability High tem perature soldering guaranteed: 350 o C / 10 seconds, 0.375”(9.5m m ) lead length, 5 lbs., (2.3kg) tension. M echanical Data Case: JEDEC DO -41 m olded plastic over glass body Lead: Plated Axial leads, solderable per M IL-STD-750, M ethod 2026 Polarity: Color band denotes cathode end M ounting position: Any W eight: 0.012 ounce, 0.3 gram D im ensions in inches and (m illim eters) M axim um Ratings and Electrical Characteristics Rating at 25℃ am bient tem perature unless otherwise specified. Sym bol ARGP ARGP ARGP Type Num ber M axim um Recurrent Peak Reverse Voltage M axim um RM S Voltage M axim um DC Blocking Voltage M in. Reverse Avalanche Breakdown Voltage @ IR=0.1m A M axim um Average Forward R ectified Current .375” (9.5m m ) Lead Length @ T tp = 55℃ Peak Forw ard Surge Current @ t= 8.3 m s Single Half Sine-wave Superim posed on Rated Load (JEDEC method ) @ t=10m s half sine wave, Tj=Tjm ax prior to surge, VR =V RRM m ax Non-repetitive Peak Reverse Avalanche Energy L=120m H Tj=125 ℃ m ax prior to Surge, Inductive load Switched off M axim um Instantaneous Forward Voltage @ IF= 1.0A @ IF=1A, Tj=Tj m ax. M axim um DC Reverse Current @ T J =25℃ at Rated D C Blocking Voltage @ T J =165℃ M axim um R everse Recovery Tim e ( Note 1 ) T J =25 ℃ Typical Junction Capacitance ( Note 2 ) Typical Therm al Resistance (Note 3) O perating Tem perature Range T J 10G 10J ARGP 10K ARGP 10M Units 10D V RRM V RM S VR 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 V V V V (BR)R 300 500 700 900 1100 V I F(AV) 1.3 A I FSM 30 A 20 A E RSM 10 IR 250 V V uA uA nS pF 300 15.0 120 55 -65 to + 175 -65 to + 175 Storage Tem perature Range T STG Notes: 1. Reverse Recovery Test Conditions: I F =0.5A, I R =1.0A Recover to 0.25A. 2. M easured at 1.0 M Hz and Applied Reverse Voltage of 4.0 Volts. 3. M ount on Cu-Pad Size 5m m x 5m m on P.C.B. - 582 - mJ 1.3 1.1 1.0 100.0 VF Trr Cj R θ JA R θ TP TJ T STG 7 O C/W O O C C RATINGS AND CHARACTERISTIC CURVES (ARGP10D THRU ARGP10M) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 1cm 1.0 0.75 0.5 0.25 0.375" (9.5mm) LEAD LENGTH 0 50 75 100 125 150 175 o PEAK FORWARD SURGE CURRENT. (A) TIE POINT TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 Tj=Tj max. 8.3ms Single Half Sine Wave JEDEC Method 20 INSTANTANEOUS FORWARD CURRENT. (A) RESISTIVE OR INDUCTIVE LOAD 25 1 0.1 0 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0.01 0.4 0.6 0.8 1.0 1.2 FORWARD VOLTAGE. (V) 1.4 1.6 FIG.6- TYPICAL REVERSE CHARACTERISTICS 10 20 10 0 100 10 1 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 100 JUNCTION CAPACITANCE.(pF) FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10 1.5 1.25 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES AVERAGE FORWARD CURRENT. (A) FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE SET TIME BASE FOR 5/ 10ns/ cm Tj=125 0C 1 Tj=75 0C 0.1 Tj=25 0C 10 Tj=25 0C 0.01 0 1 10 100 REVERSE VOLTAGE. (V) - 583 - 0 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 140