Document 439 Flyback Transformers For Texas Instruments TPS23750 PoE Powered Device Controller • Isolated synchronous flyback transformers developed for Texas Instruments PMP929 reference design. • Operates up to 500 kHz with 18 – 72 V input • 1500 Vrms isolation primary and bias to secondary windings Core material Ferrite Terminations RoHS tin-silver over tin over nickel over phos bronze. Other terminations available at additional cost. Weight 5.0 – 5.3 g Ambient temperature –40°C to +125°C Storage temperature Component: –40°C to +125°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 200 per 13″ reel Plastic tape: 44 mm wide, 0.35 mm thick, 28 mm pocket spacing, 9.6 mm pocket depth PCB washing Only pure water or alcohol recommended L at 0 A2 L at Ipk3 DCR max (Ohms) Part ±10% min number1 (µH) (µH) pri sec4 drive bias C1173-AL_ 166.5 150.0 0.770 0.020 0.523 1.12 C1174-AL_ 150.0 135.0 0.515 0.023 0.570 0.88 Leakage L5 max (µH) Turns ratio pri drive pri:sec6 pri:drive pri:bias 2.50 0.400 6.5:1 3.7:1 2.0:1 2.00 0.400 5.0:1 3.2:1 2.25:1 1. When ordering, please specify packaging code: C1174-ALD Packaging: D = 13″ machine ready reel. EIA-481 embossed plastic tape (200 per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter D instead. 2. Inductance is for the primary, measured at 100 kHz, 0.1 Vrms. 3. Peak primary current drawn at minimum input voltage. Dot indicates pin 1 0.028 0,72 1 0.135 3,43 0.07 1,79 12 11 3 12 Primary 0.677 max 17,20 YYXXXX-AL 6 0.865 max 21,97 0.098 2,5 Recommended Land Pattern 0.098 2,5 0.335 max 8,51 Bias Drive 1 7 0.004 /0,10 0.693 17,60 Dimensions are in inches mm Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 2 The secondary windings are to be connected in parallel on the PC board. 0.590 14,98 0.079 2,01 Secondary 9 10 8 5 7 Drive output 5.6 V, 10 mA 7.5 V, 10 mA 4. DCR for secondary is with windings connected in parallel. 5. Leakage inductance for the primary is with the secondary and drive windings shorted; leakage inductance for the drive winding is with the secondary windings shorted. 6. Turns ratio is with both secondary windings connected in parallel. 7. Output of the secondary is with the windings connected in parallel. Bias winding output is 10 V, 20 mA. 8. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. 0.665 16,88 1 12 Ipk3 (A) Output7 1.2 3.3 V, 3 A 1.2 5.0 V, 2 A Document 439 Revised 10/28/08