MICREL MIC5325

MIC5325
Low VIN/VOUT 400mA ULDO™
with Ultra-Low IQ
General Description
Features
The MIC5325 is a high-performance, µCap, low-dropout
regulator, offering ultra-low operating current while
maintaining very fast transient response. The MIC5325
can source up to 400mA of output current and allows a low
input supply voltage source to increase system efficiency.
Ideal for battery operated applications; the MIC5325 offers
high accuracy, extremely low dropout voltage, and low
ground current at all load conditions. The MIC5325 can
also be put into a zero-off-mode current state, drawing
virtually no current when disabled.
The MIC5325 is available in fixed-output voltages in the
6-pin 2mm x 2mm Thin MLF® leadless package.
Data sheets and support documentation can be found on
Micrel’s web site at www.micrel.com.
•
•
•
•
•
•
•
•
•
•
Wide-input voltage range: 1.7V to 5.5V
Stable with 1µF ceramic output capacitor
Ultra-low-dropout voltage ULDO™ 110mV @ 400mA
±2% voltage accuracy over temperature
Bias supply voltage range: 2.5V to 5.5V
Ultra-low ground current 35µA typical
400mA maximum output current per LDO
Very fast transient response
Thermal-shutdown and current-limit protection
Tiny 6-pin 2mm x 2mm Thin MLF® package
Applications
•
•
•
•
Low-power handheld devices
Portable electronics
GPS receivers
Post regulator
___________________________________________________________________________________________________________
Typical Application
ULDO is a trademark of Micrel, Inc
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
March 2011
M9999-030811-C
Micrel, Inc.
MIC5325
Ordering Information
Part Number
Marking Code
Output
Voltage
Temperature Range
Package
MIC5325-1.2YMT
QG4
1.2V
–40°C to +125°C
6-Pin 2mm x 2mm Thin MLF®
Pb-Free
®
Pb-Free
Lead Finish
MIC5325-1.5YMT
QGF
1.5V
–40°C to +125°C
6-Pin 2mm x 2mm Thin MLF
MIC5325-1.8YMT
QGG
1.8V
–40°C to +125°C
6-Pin 2mm x 2mm Thin MLF®
Pb-Free
–40°C to +125°C
®
Pb-Free
MIC5325-3.6YMT
QGV
3.6V
6-Pin 2mm x 2mm Thin MLF
Notes:
1.
Other voltages available. Contact Micrel for details.
2.
▲ = Pin 1 identifier.
Pin Configuration
6-Pin 2mm x 2mm Thin MLF® (MT)
Pin Description
Pin
Number
Pin Name
1
VBIAS
2
GND
3
IN
4
OUT
Output of regulator.
5
BYP
Bypass: Connect a capacitor to ground to reduce noise and reduce ripple rejection.
6
EN
March 2011
Pin Function
Bias Input Voltage.
Ground
Power Input for LDO.
Enable Input: Active High Input. Logic High = On; Logic Low = Off. Do not leave floating.
2
M9999-030811-C
Micrel, Inc.
MIC5325
Absolute Maximum Ratings(1)
Operating Ratings(2)
Supply Voltage (VIN) ............................................ 0V to VBIAS
Bias Voltage (VBIAS) ................................................ 0V to 6V
Enable Voltage (VEN)........................................... 0V to VBIAS
Power Dissipation (PD) ........................... Internally Limited(3)
Lead Temperature (soldering, 10 µsec.).................... 260°C
Junction Temperature (TJ) ........................–40°C to +125°C
Storage Temperature (Ts) .........................–65°C to +150°C
ESD Rating(4) .................................................................. 2kV
Supply Voltage (VIN)......................................... 1.7V to VBIAS
Bias Voltage (VBIAS).......................................... 2.5V to 5.5V
Enable Voltage (VEN)........................................... 0V to VBIAS
Junction Temperature (TJ) ........................ –40°C to +125°C
Junction Thermal Resistance
2x2 Thin MLF-6 (θJA) .........................................90°C/W
Electrical Characteristics(5)
VBIAS = 3.6V or VIN (whichever is greater); VIN = VOUT + 1V; COUT = 1µF; IOUT = 100µA; TJ = 25°C, bold values indicate –40°C to +125°C,
unless noted.
Parameter
Condition
Min.
Output Voltage Accuracy
Variation from nominal VOUT
–2.0
VBIAS Line Regulation
VBIAS = VIN to 5.5V; VIN = VOUT + 1V
VIN Line Regulation
Load Regulation
VIN Dropout Voltage
IOUT = 400mA
Ground Pin Current
IOUT = 100µA to 400mA; VIN = VEN; VBIAS = 5.5V
Ground Pin Current in Shutdown
VEN ≤ 0.2V
Ripple Rejection
Typ.
Max.
Units
+2.0
%
0.03
0.6
%
VBIAS = 5.5V; VIN = VOUT + 1V to 5.5V
0.02
0.6
%
IOUT = 100µA to 400mA
0.3
2
%
110
250
mV
35
55
µA
0.01
1
µA
f = up to 1kHz; COUT = 1µF; no CBYP
60
dB
f = up to 1kHz; COUT = 1µF; CBYP = 10nF
65
dB
f = 1kHz – 20kHz; COUT = 1µ F; CBYP = 10nF
40
dB
680
mA
30
µVRMS
Current Limit
VOUT = 0V
450
Output Voltage Noise
COUT = 1µF; CBYP = 10nF; 10Hz to 100kHz
Enable Inputs (EN)
Enable Input Voltage
Enable Input Current
Turn-On Time
Logic Low
0.2
Logic High
V
V
1.2
VIL ≤ 0.2V
0.01
µA
VIH ≥ 1V
0.02
µA
COUT = 1µF; CBYP = 10nF
150
500
µs
Notes:
1. Exceeding the absolute maximum rating may damage the device.
2. The device is not guaranteed to function outside its operating rating.
3. The maximum allowable power dissipation of any TA (ambient temperature) is PD(max) = (TJ(max) – TA) / θJA. Exceeding the maximum allowable power
dissipation will result in excessive die temperature, and the regulator will go into thermal shutdown.
4. Devices are ESD sensitive. Handling precautions recommended. Human body model, 1.5kΩ in series with 100pF.
5. Specification for packaged product only.
March 2011
3
M9999-030811-C
Micrel, Inc.
MIC5325
Typical Characteristics
-120
Power Supply
Rejection Ratio (V IN )
-100
-100
50mA
100µA (NO BYP)
-80
-60
-120
100mA
100µA
VIN = VOUT +1V
300mA
-20 VOUT = 1.2V
COUT = 1µF
CBYP = 0.01µF
0
0.1
1
10
100
FREQUENCY (kHz)
6
5
4
3
2
-40
1,000
Ground Current (V IN )
vs. Output Current
VIN = VOUT +1V
-20 VOUT = 1.2V
COUT = 1µF
400mA
CBYP = 0.01µF
0
0.1
1
10
100
FREQUENCY (kHz)
18
1,000
Ground Current (V BIAS )
vs. Output Current
14
12
8
6
50 100 150 200 250 300 350 400
OUTPUT CURRENT (mA)
2.0
100µA
1.8
1.6
400mA
1.4
1.2
1.0
0.8
0.6
VBIAS = 5.5V
0.4
VOUT = 1.8V
0.2
COUT = 1µF
0
1 1.5 2 2.5 3 3.5 4 4.5 5 5.5
VIN (V)
Ground Current (V IN )
vs. Temperature
14
12
10
8
6
4
2
100µA
400mA
VBIAS = 3.6V
VIN = 2.8V
VOUT = 1.8V
0
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
March 2011
VBIAS = 3.6V
VIN = 2.8V
VOUT = 1.8V
COUT = 1µF
CBYP = 0.01µF
4
2
0
0
140
1
0
1.5 2 2.5 3 3.5 4 4.5 5 5.5
VIN (V)
30
Ground Current (Total)
vs. Output Current
22
20
18
10
VIN = 2.8V
VOUT = 1.8V
COUT = 1µF
CBYP = 0.01µF
VBIAS = 5.5V
VOUT = 1.8V
COUT = 1µF
CBYP = 0.01µF
28
26
24
16
Output Voltage
vs. V IN
20
18
16
-80
100µA (NO BYP)
400mA
10
Ground Current (V IN )
vs. V IN
9
8
7
100µA
-60
-40
10
9
8
7
6
5
4
3
2
1
0
0
Power Supply
Rejection Ratio (V BIAS )
50 100 150 200 250 300 350 400
OUTPUT CURRENT (mA)
Dropout Voltage
vs. Temperature
16
14
12
10
0
140
50 100 150 200 250 300 350 400
OUTPUT CURRENT (mA)
Dropout Voltage
vs. Output Current
120
120
400mA
100
100
80
80
60
60
200mA
40
40
100mA
20
0
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
Current Limit
vs. V IN
900
875
850
825
800
775
750
725
700
VBIAS = 5.5V
675
VOUT = 1.8V
650
COUT = 1µF
625
CIN = 1µF
600
1.5 2 2.5 3 3.5 4 4.5 5 5.5
VIN (V)
4
20
0
0
1.8
VBIAS = 3.6V
VIN = 2.8V
COUT = 1µF
CBYP = 0.01µF
CBAIS = 1µF
CIN = 1µF
50 100 150 200 250 300 350 400
OUTPUT CURRENT (mA)
Output Voltage
vs. Output Current
1.75
1.7
1.65
1.6
0
VBIAS = 3.6V
VIN = 2.8V
COUT = 1µF
CBYP = 0.01µF
CIN = 1µF
50 100 150 200 250 300 350 400
OUTPUT CURRENT (mA)
M9999-030811-C
Micrel, Inc.
MIC5325
Typical Characteristics (Continued)
1.30
Output Voltage
vs. Temperature
20
18
1.25
16
14
1.20
12
10
8
1.15
VIN = 2.2V
VBIAS = 3.6V
VOUT = 1.2V
COUT = 1µF
IOUT = 100µA
1.10
-40 -20 0 20 40 60 80 100 120
TEMPERATURE (°C)
March 2011
Bias Current
vs. Enable Voltage
10
400mA
1
Output Noise
Spectral Density
VIN = 4.5V
VOUT = 1.8V
COUT = 1µF
CBYP = 0.01µF
100µA
VBIAS = 3.6V
VIN = 2.8V
VOUT = 1.8V
CIN = 1µF
COUT = 1µF
CBYP = 0.01µF
6
4
2
0
0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5
ENABLE VOLTAGE (V)
5
0.1
0.01
10
Noise (10Hz to 1MHz) = 59µVRMS
100
1K
10K 100K
FREQUENCY (Hz)
1M
M9999-030811-C
Micrel, Inc.
MIC5325
Functional Characteristics
March 2011
6
M9999-030811-C
Micrel, Inc.
MIC5325
Functional Diagram
CURRENT
LIMIT
VBIAS
VIN
VOUT
LDO
EN
QUICK START
REFERENCE
BYP
THERMAL
LIMIT
GND
March 2011
7
M9999-030811-C
Micrel, Inc.
MIC5325
Bypass Capacitor
A capacitor can be placed from the noise bypass pin-toground to reduce output voltage noise. The capacitor
bypasses the internal reference. A 0.01µF capacitor is
recommended for applications that require low-noise
outputs. The bypass capacitor can be increased, further
reducing noise and improving PSRR. Turn-on time
increases slightly with respect to bypass capacitance. A
unique, quick-start circuit allows the MIC5325 to drive a
large capacitor on the bypass pin without significantly
slowing turn-on time.
Application Information
The MIC5325 is a high performance, low-dropout linear
regulator designed for low current applications requiring
fast transient response. The MIC5325 utilizes two input
supplies, significantly reducing dropout voltage, perfect for
low-voltage, DC-to-DC conversion. The MIC5325 requires
a minimum of external components.
The MIC5325 regulator is fully protected from damage
due to fault conditions, offering linear current limiting and
thermal shutdown.
Bias Supply Voltage
VBIAS, requiring relatively light current, provides power to
the control portion of the MIC5325. Bypassing on the bias
pin is recommended to improve performance of the
regulator during line and load transients. 1µF ceramic
capacitor from VBIAS-to-ground helps reduce high
frequency noise from being injected into the control
circuitry from the bias rail and is good design practice.
Minimum Load Current
The MIC5325, unlike most other regulators, does not
require a minimum load to maintain output voltage
regulation.
Enable/Shutdown
The MIC5325 comes with a single active-high enable pin
that allows the regulator to be disabled. Forcing the
enable pin low disables the regulator and sends it into a
“zero” off-mode-current state. In this state, current
consumed by the regulator goes nearly to zero. Forcing
the enable pin high enables the output voltage. The
active-high enable pin uses CMOS technology and the
enable pin cannot be left floating; a floating enable pin
may cause an indeterminate state on the output.
Input Supply Voltage
VIN provides the supply to power the LDO. The minimum
input voltage is 1.7V, allowing conversion from low
voltage supplies.
Output Capacitor
The MIC5325 requires an output capacitor of 1µF or
greater to maintain stability. The design is optimized for
use with low-ESR ceramic chip capacitors. High ESR
capacitors may cause high frequency oscillation. The
output capacitor can be increased, but performance has
been optimized for a 1µF ceramic output capacitor and
does not improve significantly with larger capacitance.
X7R/X5R dielectric-type ceramic capacitors are recommended because of their temperature performance. X7Rtype capacitors change capacitance by 15% over their
operating temperature range and are the most stable type
of ceramic capacitors. Z5U and Y5V dielectric capacitors
change value by as much as 50% and 60%, respectively,
over their operating temperature ranges. To use a
ceramic chip capacitor with Y5V dielectric, the value must
be much higher than an X7R ceramic capacitor to ensure
the same minimum capacitance over the equivalent
operating temperature range.
Thermal Considerations
The MIC5325 is designed to provide 400mA of continuous
current in a very small package. Maximum ambient
operating temperature can be calculated based on the
output current and the voltage drop across the part. Given
that the input voltage is 1.8V, the output voltage is 1.2V
and the output current = 400mA. The actual power
dissipation of the regulator circuit can be determined
using the equation:
PD = (VIN – VOUT1) I OUT + VIN IGND
Because this device is CMOS and the ground current is
typically <100µA over the load range, the power
dissipation contributed by the ground current is < 1% and
can be ignored for this calculation.
PD = (1.8V – 1.2V) × 400mA
PD = 0.18W
To determine the maximum ambient operating
temperature of the package, use the junction-to-ambient
thermal resistance of the device and the following basic
equation:
Input Capacitor
The MIC5325 is a high-performance, high bandwidth
device. Therefore, it requires a well-bypassed input
supply for optimal performance. A 1µF capacitor is
required from the input-to-ground to provide stability. LowESR ceramic capacitors provide optimal performance at a
minimum of space. Additional high-frequency capacitors,
such as small-valued NPO dielectric-type capacitors, help
filter out high-frequency noise and are good practice in
any RF-based circuit.
March 2011
⎛ TJ(max) − TA
PD(max) = ⎜⎜
θ JA
⎝
⎞
⎟
⎟
⎠
TJ(max) = 125°C, the maximum junction temperature of the
die θJA thermal resistance = 90°C/W.
8
M9999-030811-C
Micrel, Inc.
MIC5325
Bill of Materials
Item
Part Number
C1, C2, C4
VJ0603G105KXYCW1BC
Vishay(1)
VJ0603Y103KXQCW1BC
(2)
C3
R3
U1
CRCW060310K0FKEA
MIC5325-xxYMT
Manufacturer
Murata
Qty.
3
Capacitor, 0.01µF, 10V, Size 0603
1
(1)
Resistor, 10k, 1%, 1/16W, Size 0603
1
(3)
400mA ULDO™ with Ultra-Low IQ
1
Vishay Dale
Micrel, Inc.
Description
Capacitor, 1µF, 6.3V, Size 0603
Notes:
1. Vishay: www.vishay.com.
2. Murata: www.murata.com.
3. Micrel, Inc.: www.micrel.com.
March 2011
9
M9999-030811-C
Micrel, Inc.
MIC5325
PCB Layout Recommendations
Top Layer
Bottom Layer
March 2011
10
M9999-030811-C
Micrel, Inc.
MIC5325
Package Information
6-Pin 2mm x 2mm Thin MLF® (MT)
MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA
TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com
Micrel makes no representations or warranties with respect to the accuracy or completeness of the information furnished in this data sheet. This
information is not intended as a warranty and Micrel does not assume responsibility for its use. Micrel reserves the right to change circuitry,
specifications and descriptions at any time without notice. No license, whether express, implied, arising by estoppel or otherwise, to any intellectual
property rights is granted by this document. Except as provided in Micrel’s terms and conditions of sale for such products, Micrel assumes no liability
whatsoever, and Micrel disclaims any express or implied warranty relating to the sale and/or use of Micrel products including liability or warranties
relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right.
Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product
can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical
implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user.
A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to
fully indemnify Micrel for any damages resulting from such use or sale.
© 2007 Micrel, Incorporated.
March 2011
11
M9999-030811-C