1.25Gbps HIGH-SPEED LIMITING POST AMPLIFIER Not recommended for new designs Micrel, Inc. DESCRIPTION FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Up to 1.25Gbps operation Low noise Chatter-Free /LOS Generation PECL /LOS Output TTL /EN Input Differential PECL inputs for data /EN input is TTL with internal 27K pull-up Single power supply Designed for use with SY88902 and SY88904 Available in a tiny 10-pin (3mm x3 mm) MSOP The SY88913 limiting post amplifier with its high gain and wide bandwidth is ideal for use as a post amplifier in fiber-optic receivers with data rates up to 1.25Gbps. Signals as small as 5mVp-p can be amplified to drive devices with PECL inputs. The SY88913 generates a chatter-free PECL Loss of Signal (/LOS). The SY88913 incorporates a programmble level detect function to identify when the input signal has been lost. This information can be fed back to the /EN input of the device to maintain stability under loss of signal conditions. Using LOSLVL pin the sensitivity of the level detect can be adjusted. The LOS LVL voltage can be set by connecting a resistor divider between VCC and VREF, Figure 2. Figure 3 shows the relationship between input level sensitivity and the voltage set on LOSLVL. Figure 4 shows the relationship between input level sensitivity and resistor divider ratio. APPLICATIONS ■ ■ ■ ■ SY88913 SY88913 1.25Gbps Gigabit Ethernet 531Mbps and 1062Mbps Fibre Channel 622Mbps SONET Gigabit Interface Converter BLOCK DIAGRAM DIN DOUT Limiting Amplifier ECL Buffer DOUT DIN VREF Enable EN VCC Level Detect GND LOS LOSLVL M9999-061907 [email protected] or (408) 955-1690 Rev.: G 1 Amendment: /0 Issue Date: June 2007 Micrel, Inc. SY88913 PACKAGE/ORDERING INFORMATION Ordering Information /EN 1 10 VCC DIN 2 9 DOUT MSOP K10-1 /DIN 3 8 /DOUT VREF 4 7 /LOS LOSLVL 5 6 GND Part Number Package Type Operating Range Package Marking Lead Finish SY88913KC K10-1 Commercial 913 Sn-Pb SY88913KCTR(1) K10-1 Commercial 913 Sn-Pb SY88913KG K10-1 Commercial 913 with Pb-Free bar-line indicator Pb-Free NiPdAu SY88913KGTR(1) K10-1 Commercial 913 with Pb-Free bar-line indicator Pb-Free NiPdAu 10-Pin MSOP (K10-1) Note: 1. Tape and Reel. PIN NAMES Pin GENERAL DESCRIPTION Type General The SY88913 is an integrated limiting amplifier intended for high-frequency fiber-optic applications. The circuit connects to typical transimpedance amplifiers found within a fiber-optics link. The linear signal output from a transimpedance amplifier can contain significant amounts of noise, and may vary in amplitude over time. The SY88913 limiting amplifier quantizes the signal and outputs a voltagelimited waveform. The TTL /EN pin allows the user to disable the signal without removing the input signal. Function DIN Data Input Data Input /DIN Data Input Inverting Data Input LOS LVL Input Loss of Signal Level Set /EN TTL Input Output Enable (active Low) /LOS PECL Output Loss of Signal Indicator (active Low) GND Ground Ground DOUT PECL Output Data Output /DOUT PECL Output Inverting Data Output VCC Power Supply Positive Power Supply VREF Output Reference Voltage Output for LOS Level Set (see Fig. 2) M9999-061907 [email protected] or (408) 955-1690 2 Micrel, Inc. SY88913 ABSOLUTE MAXIMUM RATINGS(1) Symbol Rating Value Unit VCC Power Supply Voltage 0 to +7.0 V DIN, /DIN Input Voltage 0 to VCC V DOUT, /DOUT, /LOS Output Voltage (with 50Ω load) VCC –2.5, VCC +0.3 V TA Operating Temperature Range –40 to +85 °C Tstore Storage Temperature Range –55 to +125 °C Note: 1. Permanent device damage may occur if absolute maximum ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this data sheet. Exposure to absolute maximum ratlng conditions for extended periods may affect device reliability. DC ELECTRICAL CHARACTERISTICS VCC = +5V ±10%, RLOAD = 50Ω to VCC–2V, TA = –40°C to +85°C. TA = –40°C Symbol ICC IIL Parameter Power Supply Current(1) /EN Input LOW Current IIH /EN Input HIGH Current VCMR Common Mode Range TA = 0°C TA = +25°C TA = +85°C Min. Max. Min. Max. Min. Typ. Max. Min. Max. Unit — 21 35 — 35 mA — — –0.3(5) — mA — — 20(2) 100(3) — — 20(2) 100(3) µA 35 — 35 — –0.3(5) — –0.3(5) — –0.3(5) — — 20(2) 100(3) — — 20(2) 100(3) — — GND +2.0 VCC–1.0 GND +2.0 VCC–1.0 GND +2.0 — Voffset Differential Output Offset LOSLVL LOSLVL Level VOH DOUT and /DOUT HIGH Output VCC–1085 VCC–880 VCC–1025 VCC–880 VCC–1025 VCC–955 VOL VCC–1.0 GND +2.0 VCC–1.0 V — ±100 — ±100 — — ±100 — ±100 mV VREF VCC VREF VCC VREF — VCC VREF VCC V VCC–880 mV DOUT and /DOUT LOW Output VCC–1830 VCC–1555 VCC–1810 VCC–1620 VCC–1810 VCC–1705 VCC–1620 VCC–1810 VCC–1620 mV VREF Reference Supply(4) VCC–2.625 VCC–2.325 VCC–2.625 VCC–2.325 VCC–2.625 VCC–2.475 VCC–2.325 VCC–2.625 VCC–2.325 V VIH /EN Input HIGH Voltage 2.0 — 2.0 — 2.0 — — 2.0 — V VIL /EN Input LOW Voltage — 0.8 — 0.8 — — 0.8 — 0.8 V Notes: 1. No output load. 2. VIN = 2.7V. 3. VIN = VCC. 4. IREF must be limited to be within –0.8mA (source) and 0.5mA (sink). 5. VIN = 0.5V. M9999-061907 [email protected] or (408) 955-1690 3 VCC–880 VCC–1025 Micrel, Inc. SY88913 AC ELECTRICAL CHARACTERISTICS VCC = +5V ±10%, RLOAD = 50Ω to VCC–2V, TA = –40°C to +85°C. TA = –40°C Symbol Parameter PSRR Supply(1) TA = 0°C TA = +25°C TA = +85°C Min. Max. Min. Max. Min. Typ. Max. Min. Max. Unit Power Rejection Ratio — — — — — 35 — — — dB VID Input Voltage Range 5 1800 5 1800 5 — 1800 5 tr, tf Output Rise/Fall Time — — 350 — — — 350 — — — 200 trin,tfin 350 — — — VOD Differential Output Voltage Swing(2) — — — — — — — — — — 600 200 — — — — — — mV mV tOFFL /LOS Release Time(3) Minimum Input — 0.5 — 0.5 — 0.1 0.5 — 0.5 µs tOFFH /LOS Release Time(4) Maximum Input — 0.5 — 0.5 — 0.1 0.5 — 0.5 µs tONL /LOS Assert Time(3) — 0.5 — 0.5 — 0.2 0.5 — 0.5 µs VSR /LOS Sensitivity Range 5 50 5 50 5 — 50 5 50 mVPP HYS /LOS Hysteresis 2 8 2 8 2 4.6 8 2 8 dB Notes: 1. Input referred noise = RMS output noise/low frequency gain. 2. Input is 622MHz square wave. 3. Input is a 200MHz square wave, tr < 300ps, 8mVPP. 4. Input is a 200MHz square wave, tr < 300ps, 1.8VPP. M9999-061907 [email protected] or (408) 955-1690 4 1800 mVPP 350 ps — Conditions Input referred, 55MHz VID > 100mVPP VID < 100mVPP VID = 15mVPP VID = 5mVPP Micrel, Inc. SY88913 APPLICATION NOTE Output Termination The SY88913 outputs must be terminated with a 50Ω load to VCC – 2V (or Thevenin equivalent). The SY88913 ground pin should be connected to the circuit board ground. Use multiple PCB vias close to the part to connect to ground. Avoid long, inductive runs which can degrade performance. Layout and PCB Design Since the SY88913 is a high-frequency component, performance can largely be determined by board layout and design. A common problem with high-gain amplifiers is feedback from the large swing outputs to the input via the power supply. VCC 0.1µF DIN+ 0.1µF DIN– 50Ω R1 LOSLVL R2 50Ω VREF VREF 0.1µF Notes: Resistor Divider = R2/ (R1 + R2) R1 + R2 ≥ 5kΩ Figure 1. Differential Input Configuration M9999-061907 [email protected] or (408) 955-1690 Figure 2. LOSLVL Circut 5 Micrel, Inc. SY88913 PERFORMANCE CURVE 100.00 90.00 Deassert 80.00 70.00 Level (mV) 60.00 Assert 50.00 40.00 30.00 20.00 10.00 5.00 4.75 4.88 4.63 4.38 4.51 4.13 4.26 4.01 3.76 3.89 3.52 3.64 3.39 3.14 3.27 2.90 3.02 2.77 2.53 2.65 0.00 LOSlvl (V) Figure 3. LOS Assert and Deassert Levels vs Resistor Divider 100.00 90.00 80.00 Deassert 70.00 Level (mV) 60.00 Assert 50.00 40.00 30.00 20.00 10.00 Resistor Divider R2 / (R1 + R2) Figure 4. Resistor Divider R2 / (R1 + R2) M9999-061907 [email protected] or (408) 955-1690 6 1.00 0.95 0.90 0.85 0.75 0.80 0.70 0.65 0.60 0.50 0.55 0.45 0.40 0.35 0.25 0.30 0.20 0.15 0.10 0.00 0.05 0.00 SY88913 Micrel, Inc. APPLICATION EXAMPLE FOR 3-CHIP SET SOLUTION GBIC Terminal TX_DATA+ TX_DATA– VCC DIN DIN LOSOUT EN LOSIN VREF RSET 20kΩ VREF GND SY88902 VCC IBIAS GND SY88905 VCC LOS SY88913 VCC OUT RSER VCC 20kΩ 20kΩ OUT MD IBIAS SET IBIAS FB IPIN SET DIN DIN 0.1µF BLM21A102S VCC Laser Module The value of RSER depends on the Laser Diode. VCC 7 M9999-061907 [email protected] or (408) 955-1690 24Ω LOSLVL 82Ω REXT Laserdiode VREF 130Ω 330kΩ 82Ω 1000pF 82Ω 82Ω 130Ω Photodiode 130Ω 130Ω VCC EN DOUT DOUT GND 0.1µF 82Ω 82Ω ENABLE/DISABLE CD RX_DATA+ RX_DATA– VCC 20kΩ 130Ω 130Ω Micrel, Inc. SY88913 10 LEAD MSOP (K10-1) Rev. 00 MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is at Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2005 Micrel, Incorporated. M9999-061907 [email protected] or (408) 955-1690 8