Ordering number : ENA0303 Monolithic Linear IC LA6393JM High-Performance Dual Comparator Overview The LA6393JM is a high-performance dual comparator that is capable of operating from a single power supply over a wide range of 2V to 36V. Because of its excellent input characteristics and low power, it can be very conveniently applied to multi-signal parallel comparator circuits that require high-density assembly. Functions • High-performance dual operational amplifier • Wide supply voltage range (Single supply : 2.0 to 36.0V,dual supplies : ±1.0 to 18.0V). • Wide common-mode input voltage range (0 to VCC – 1.8V). • Open collector output enabling wired OR. • Small current drain (0.6mA) and low power. • Mini flat package enabling compactness of sets. Specifications Maximum Ratings at Ta = 25°C Parameter Symbol Conditions Ratings Unit Maximum supply voltage VCC max 36 V Differential input voltage VID 36 V Maximum input voltage VIN max -0.3 to +36 V Allowable power dissipation Pd max Ta≤25°C 300 mW Operating temperature Topr -40 to +85 °C Storage temperature Tstg -55 to +150 °C Recommended Operating Conditions at Ta = 25°C Parameter Symbol Ratings Conditions Min Supply voltage VCC typ 2 Unit Max 24 V Any and all SANYO Semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO Semiconductor representative nearest you before using any SANYO Semiconductor products described or contained herein in such applications. SANYO Semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor products described or contained herein. 92706 / 41006 MS OT 20060410-S00006 No.A0303-1/5 LA6393JM Electrical Characteristics at Ta = 25°C, VCC = 5V Parameter Symbol Conditions Test Circuit Ratings min typ Unit max Input offset voltage VIO 1 ±2 ±7 mV Input offset current IIO 2 ±5 ±50 nA Input bias current IB 3 45 250 nA VCC-1.8 V Common-mode input voltage range VICM 0 Current drain ICC RL = ∞ 4 0.5 Voltage gain VG RL = 15kΩ 5 200 V/mV Response time RT VRL = 5V, RL = 5.1kΩ VIN- = 0.5V, VIN+ = 0V, VO ≤ 1.5V VIN- = 0.5V, VIN+ = 0V, ISINK ≤ 3mA VIN- = 0V, VIN+ = 0.5V, VO = 5V 6 1.3 µs Output sink current ISINK Output saturation voltage VOL Output leakage current ILEAK 7 6 1.2 16 8 0.2 9 0.1 mA mA 0.4 V nA Package Dimensions unit : mm 3032D 5.0 5 0.63 4.4 6.4 8 4 0.35 0.15 0.1 (1.5) 1.27 1.7max 1 (0.65) SANYO : MFP8(225mil) Pin Assignment No.A0303-2/5 LA6393JM Equivalent Circuit Test Circuits 1. Input offset voltage VIO 3. Input bias current IB (−) 2. Input offset current IIO Input bias current IB (+) No.A0303-3/5 LA6393JM 4. Current drain ICC 5. Voltage gain VG 6. Response time RT ∆V:Over drive 7. Output sink current ISINK 8. Output saturation voltage VOL 9. Output leakage current ILEAK No.A0303-4/5 LA6393JM Application Circuit Examples Voltage comparator (with hysteresis) Square wave generator Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor products (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of April, 2006. Specifications and information herein are subject to change without notice. PS No.A0303-5/5