Ordering number : ENA0927A Monolithic Digital IC Low-Saturation Bidirectional Motor Driver for Low-Voltage Drive LB1838JM Overview The LB1838JM is a low-saturation two-channel bidirectional motor driver IC for use in low-voltage applications. It has a wide operating temperature range of -40 to 80°C and is ideal for 2-phase excitation bipolar stepping motor driver IC used in automotive components (other than critical safety parts), consumer and industrial products, and many other applications. Features • Low voltage operation (2.5V min) • Low saturation voltage (upper transistor + lower transistor residual voltage ; 0.40V typ at 400mA). • Through-current prevention circuit built in • Separate logic power supply and motor power supply • Spark killer diodes built in • Thermal shutdown circuit built in • Compact package (14-pin MFP) Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Maximum supply voltage Output supply voltage Conditions VS max -0.3 to +10.5 V VS to VSF V VIN GND pin flow-out current V -0.3 to +10 V Per channel 1.0 A Pd max1 Independent IC 550 mW Pd max2 * Mounted on a board. 800 mW IGND Allowable power dissipation Unit -0.3 to +10.5 VOUT Input supply voltage Ratings VCC max Operating temperature Topr -40 to +85 °C Storage temperature Tstg -55 to +150 °C 3 * Mounted on a substrate: 30×30×1.5mm , glass epoxy board. Any and all SANYO Semiconductor Co.,Ltd. products described or contained herein are, with regard to "standard application", intended for the use as general electronics equipment (home appliances, AV equipment, communication device, office equipment, industrial equipment etc.). The products mentioned herein shall not be intended for use for any "special application" (medical equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, transportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of reliability and can directly threaten human lives in case of failure or malfunction of the product or may cause harm to human bodies, nor shall they grant any guarantee thereof. If you should intend to use our products for applications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. If there is no consultation or inquiry before the intended use, our customer shall be solely responsible for the use. Specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer' s products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer' s products or equipment. 31110 SY / 91207 MS PC 20070831-S00003 No.A0927-1/5 LB1838JM Allowable Operating Ranges at Ta = 25°C Parameter Symbol Supply voltage Conditions Ratings Unit VCC 2.5 to 9.0 VS 1.8 to 9.0 V V Input high-level voltage VIH 1.8 to 9.0 V Input low-level voltage VIL -0.3 to +0.7 V Electrical Characteristics at Ta = 25°C, VCC = 3V Parameter Symbol Ratings Conditions min Supply current Output saturation voltage Unit max ICC0 EMA1, 2 = 0V, VIN1 = 3V or 0V 0.1 10 μA ICC1 EMA1 = 3V, VIN1 = 3V or 0V 12 18 mA VOUT1 EMA1 = 3V, VIN1 = 3V or 0V, IOUT = 200mA 0.20 0.28 VOUT2 EMA1 = 3V, VIN1 = 3V or 0V, IOUT = 400mA 0.40 V 0.60 V IIN VCC = 6V, VIN = 6V 200 μA IENA VCC = 6V, ENA = 6V 200 μA Input current Output sustaining voltage typ VO (SUS) IOUT = 400mA 9 V Reverse current IS (leak) VCC1, VS = 7V 30 μA Forward voltage VSF IOUT = 400mA 1.7 V Spark killer diode Package Dimensions Allowable power dissipation, Pd max – mW unit : mm (typ) 3111A 8.0 14 0.63 4.4 6.4 8 1 1.7MAX 7 1.0 0.35 0.15 0.1 (1.5) (1.0) SANYO : MFP14S(225mil) Pd max -- Ta 1000 800 600 550 Mounted on a board : 30.0×30.0×1.5mm3 glass epoxy Mounted on a board Independent IC 416 400 286 200 0 – 40 – 20 0 2025 40 60 8085 100 Ambient temperature, Ta – °C GND ENA2 OUT3 VS2 OUT4 IN2 Vcont Pin Assignment 14 13 12 11 10 9 8 2 3 4 5 6 7 OUT1 VS1 OUT2 IN1 GND VCC 1 ENA1 LB1838JM Top view Note) Ground both GND pins. No.A0927-2/5 LB1838JM Block Diagram VCC VS2 60kΩ 10μF OUT1 Control IN1 80kΩ 60kΩ ENA1 VS1 Stepping Motor OUT2 80kΩ Thermal shutdown 60kΩ IN2 OUT3 Control 80kΩ OUT4 60kΩ ENA2 80kΩ GND GND Vcont * : As long as the voltages applied to VCC, VS1, VS2, ENA1, ENA2, IN1 and IN2 are within the limits set by the absolute maximum ratings, there are no restrictions on the relationship of each voltage level in comparison with the others (regarding which is higher or lower). (ex. VCC = 3V, VS1, 2 = 2V, ENA = IN = 5V) Truth Table IN1/2 ENA1/2 OUT1/3 L H H OUT2/4 L Forward Mode H H L H Reverse L L OFF OFF Standby H L OFF OFF Standby No.A0927-3/5 LB1838JM Vcont pin VCC VS OUT M 300Ω ID IN OUT VZ ID = VZ r (= constant) Vcont As shown in the above diagram, the Vcont pin outputs the voltage of the band gap Zener VZ + VF (=1.93V). In normal use, this pin is left open. The drive current ID is varied by the Vcont voltage. However, because the band gap Zener is shared, it functions as a bridge. VO(sat) – IO IIN – VIN 200 VCC = VS = 3V 0.6 0.4 0.2 E 1( 120 IN 80 40 0 0 0 0 100 200 300 400 500 600 2 1 3 Output current, IO – mA 4 5 6 7 8 9 10 Input voltage, VIN – V VO(sat) – Ta 0.6 IS – VS 20 VCC = VS = IN = 3V VO(sat) = total value VCC = VIN =3V For 1 channel 0.5 16 IO 0.4 Current drain, IS – mA Output saturation voltage, VO (sat) – V A EN ) V =3 A N 160 0.8 Input current, IIN – μA Output saturation voltage, VO (sat) – V 1.0 A = 400m 0.2 IO = 200mA 0.3 8 4 0.1 0 – 40 12 – 20 0 20 40 60 80 100 Ambient temperature, Ta – °C 120 140 0 0 1 2 3 4 5 6 7 8 9 10 11 12 Supply voltage, VS – V No.A0927-4/5 LB1838JM ICC – VCC Current drain, ICC – mA 10 VCC = VIN =3V For 1 channel 8 6 erse Rev Forward 4 2 0 0 1 2 3 4 5 6 7 8 9 10 11 12 Supply voltage, VCC – V SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd. products described or contained herein. SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written consent of SANYO Semiconductor Co.,Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor Co.,Ltd. product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. Upon using the technical information or products described herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. This catalog provides provides information information as as of of January, March, 2010. 2007. Specifications Specifications and and information information herein herein are subject to change without notice. PS No.A0927-5/5