74VHCT16240A 16-BIT BUS BUFFER WITH 3-STATE OUTPUTS (INVERTED) ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 5.6 ns (TYP.) at VCC = 5V LOW POWER DISSIPATION: ICC = 4 µA (MAX.) at TA=25°C COMPATIBLE WITH TTL OUTPUTS: VIH = 2V (MIN.), VIL = 0.8V (MAX) POWER DOWN PROTECTION ON INPUTS & OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 8 mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL OPERATING VOLTAGE RANGE: VCC(OPR) = 4.5V to 5.5V IMPROVED LATCH-UP IMMUNITY LOW NOISE: VOLP = 0.9V (MAX.) TSSOP ORDER CODES PACKAGE TSSOP TUBE T&R 74VHCT16240ATTR PIN CONNECTION DESCRIPTION The 74VHCT16240A is an advanced high-speed CMOS 16-BIT BUS BUFFER (3-STATE) fabricated with sub-micron silicon gate and double-layer metal wiring C2MOS technology. Any nG output control governs four BUS BUFFERS. Output Enable inputs (nG) tied together give full 16 bit operation. When nG is LOW, the outputs are on. When nG is HIGH, the output are in high impedance state. This device is designed to be used with 3 state memory address drivers, etc. Power down protection is provided on all inputs and outputs and 0 to 7V can be accepted on inputs with no regard to the supply voltage. This device can be used to interface 5V to 3V since all inputs are equipped with TTL threshold All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. February 2003 1/10 74VCHT16240A INPUT EQUIVALENT CIRCUIT IEC LOGIC SYMBOLS PIN DESCRIPTION PIN No SYMBOL NAME AND FUNCTION 1 2, 3, 5, 6 8, 9, 11, 12 13, 14, 16, 17 19, 20, 22, 23 24 25 30, 29, 27, 26 36, 35, 33, 32 41, 40, 38, 37 47, 46, 44, 43 48 4, 10, 15, 21, 28, 34, 39, 45 1G 1Y1 to 1Y4 2Y1 to 2Y4 3Y1 to 3Y4 4Y1 to 4Y4 4G 3G 4A1 to 4A4 3A1 to 3A4 2A1 to 2A4 1A1 to 1A4 2G GND Ground (0V) 7, 18, 31, 42 VCC Positive Supply Voltage Output Enable Input Data Outputs Data Outputs Data Outputs Data Outputs Output Enable Input Output Enable Input Data Input Data Input Data Input Data Input Output Enable Input TRUTH TABLE INPUTS G An Yn L L H L H X H L Z X : Don‘t Care Z : High Impedance 2/10 OUTPUT 74VCHT16240A ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Value Unit Supply Voltage -0.5 to +7.0 V VI DC Input Voltage -0.5 to +7.0 V VO DC Output Voltage (see note 1) -0.5 to +7.0 V VO DC Output Voltage (see note 2) -0.5 to VCC + 0.5 - 20 V mA IIK DC Input Diode Current IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ICC or IGND DC VCC or Ground Current Storage Temperature Tstg TL Lead Temperature (10 sec) ± 50 mA -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 1) Output in OFF State 2) High or Low State RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage Value Unit 4.5 to 5.5 V VI Input Voltage 0 to 5.5 V VO Output Voltage (see note 1) 0 to 5.5 V VO Output Voltage (see note 2) 0 to VCC V Top Operating Temperature -55 to 125 °C 0 to 20 ns/V dt/dv Input Rise and Fall Time (see note 3) (VCC = 5.0 ± 0.5V) 1) Output in OFF State 2) High or Low State 3) VIN from 0.8V to 2V 3/10 74VCHT16240A DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH VOL Ioz II ICC +ICC IOPD Parameter 4.5 to 5.5 4.5 to 5.5 Low Level Output Voltage High Impedance Output Leakage Current Input Leakage Current Quiescent Supply Current Additional Worst Case Supply Current Output Leakage Current TA = 25°C VCC (V) High Level Input Voltage Low Level Input Voltage High Level Output Voltage Value Min. Typ. Max. 2 -40 to 85°C -55 to 125°C Min. Min. 2 0.8 4.5 IO=-50 µA 4.4 4.5 IO=-8 mA 3.94 4.5 IO=50 µA 4.5 Max. 4.5 0.0 Max. 2 0.8 V 0.8 4.4 4.4 3.8 3.7 Unit V V 0.1 0.1 0.1 IO=8 mA 0.36 0.44 0.55 4.5 to 5.5 VI = VIH or VIL VO = 0V to 5.5V ±0.25 ± 2.5 ± 2.5 µA 0 to 5.5 VI = 5.5V or GND ± 0.1 ± 1.0 ± 1.0 µA 5.5 VI = VCC or GND 2 20 20 µA 5.5 One Input at 3.4V, other input at VCC or GND 1.35 1.5 1.5 mA 0 VOUT = 5.5V 0.5 5.0 5.0 µA V AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3ns) Test Condition Symbol Parameter tPLH tPHL Propagation Delay Time tPZL tPZH tPZL tPZH Output Disable Time 15 50 15 50 Output Enable Time 5.0 50 (*) Voltage range is 5.0V ± 0.5V 4/10 TA = 25°C VCC (*) CL (V) (pF) 5.0 5.0 5.0 5.0 Value Min. RL = 1KΩ RL = 1KΩ -40 to 85°C -55 to 125°C Typ. Max. Min. Max. Min. Max. 5.4 7.0 7.7 8.2 8.5 9.5 10.4 11.4 1.0 1.0 1.0 1.0 9.5 10.5 12.0 13.0 1.0 1.0 1.0 1.0 10.0 11.0 12.0 13.0 8.8 11.4 1.0 13.0 1.0 13.0 Unit ns ns ns 74VCHT16240A CAPACITIVE CHARACTERISTICS Test Condition Symbol Value TA = 25°C Parameter Min. CIN Input Capacitance COUT Output Capacitance Power Dissipation Capacitance (note 1) CPD Typ. Max. 5 10 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF 9 pF 21 pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/16 (per Circuit) DYNAMIC SWITCHING CHARACTERISTICS Test Condition Symbol VOLP VOLV VIHD VILD Parameter Dynamic Low Voltage Quiet Output (note 1, 2) Dynamic High Voltage Input (note 1, 3) Dynamic Low Voltage Input (note 1, 3) TA = 25°C VCC (V) Min. 5.0 5.0 5.0 Value 1.1 CL = 50 pF Typ. Max. 0.9 1.1 -40 to 85°C -55 to 125°C Min. Min. Max. Unit Max. -0.9 V 2.0 0.8 1) Worst case package. 2) Max number of outputs defined as (n). Data inputs are driven 0V to 3.0V, (n-1) outputs switching and one output at GND. 3) Max number of data inputs (n) switching. (n-1) switching 0V to 3.0V. Inputs under test switching: 3.0V to threshold (V ILD), 0V to threshold (VIHD), f=1MHz. 5/10 74VCHT16240A TEST CIRCUIT TEST SWITCH tPLH, tPHL Open tPZL, tPLZ VCC tPZH, tPHZ GND CL =15/ 50pF or equivalent (includes jig and probe capacitance) RL = R1 = 1KΩ or equivalent RT = ZOUT of pulse generator (typically 50Ω WAVEFORM 1: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) 6/10 74VCHT16240A WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) 7/10 74VCHT16240A TSSOP48 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. A MIN. TYP. 1.2 A1 0.05 0.047 0.15 A2 MAX. 0.002 0.006 0.9 0.035 b 0.17 0.27 0.0067 0.011 c 0.09 0.20 0.0035 0.0079 D 12.4 12.6 0.488 0.496 E 8.1 BSC E1 6.0 0.318 BSC 6.2 e 0.236 0.5 BSC 0.244 0.0197 BSC K 0˚ 8˚ 0˚ 8˚ L 0.50 0.75 0.020 0.030 A A2 A1 b K e L E c D E1 PIN 1 IDENTIFICATION 1 7065588C 8/10 74VCHT16240A Tape & Reel TSSOP48 MECHANICAL DATA mm. inch DIM. MIN. A TYP MAX. MIN. 330 MAX. 12.992 C 12.8 D 20.2 0.795 N 60 2.362 T 13.2 TYP. 0.504 30.4 0.519 1.197 Ao 8.7 8.9 0.343 0.350 Bo 13.1 13.3 0.516 0.524 Ko 1.5 1.7 0.059 0.067 Po 3.9 4.1 0.153 0.161 P 11.9 12.1 0.468 0.476 9/10 74VCHT16240A Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2003 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. © http://www.st.com 10/10