TS2418 Telephone Tone Ringer with Bridge Diode DIP-8 Pin Definition: 1. Ring 5. TIP 2. Ground 7. RC 3. SRC 6. AVA 4. OFC 5. Output General Description The TS2418 is a monolithic integrated circuit telephone tone ringer with bridge diode, when coupled with an appropriate transducer, it replaces the electromechanical bell. This device is designed for use with either a piezo transducer or an inexpensive transformer coupled speaker to produce a pleasing tone composed of a high frequency (fR) alternating with a low frequency (fL) resulting in a warble frequency. The supply voltage is obtained from the AC ring signal and the circuit is designed so that noise on the line or variation of the ringing signal can not affect correct operation of the device Features Ordering Information ● On chip high voltage full wave diode bridge rectifier. ● Low current consumption, in order to allow the parallel operation of the 4 devices. ● Low external component count. ● Tone and switching frequencies adjustable by external Part No. Package Packing TS2418CD C3 DIP-8 50pcs / Tube components. ● High noise immunity due to built-in voltage current hysteresis. ● Activation voltage adjustable. ● Internal zener diodes to protect against over voltages. ● Ringer impedance adjustable with external components. Block Diagram 1/5 Version: B07 TS2418 Telephone Tone Ringer with Bridge Diode Absolute Maximum Rating Parameter Symbol Value Unit Calling Voltage (f=50Hz) Continuous VTP 120 Vrms Calling Voltage (f=50Hz) 5 Sec ON/10 Sec OFF VTP 200 Vrms Supply Current ICC 22 mA Operating Temperature TOP 0~+70 Storage and Junction Temperature Tstg -65~+150 Note: a. Maximum Rating are those values beyond which damage to the device may occur. b. Functional operation should be restricted to the Recommended Operating Conditions. 0 C 0 C Recommended Operating Conditions Description Supply Voltage Operating Temperature Symbol Min Max VCC -- 26 TA -20 Unit V 0 +70 C Note: This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND≦(VIN or VOUT)≦ VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC ). Unused output must be left open. Electrical Specifications (Ta = 25oC, unless otherwise noted) Parameter Symbol Test Conditions Min Typ Max Unit -- -- 26 V -- 1.5 1.8 mA 12.2 -- 13 V 8.0 -- 10 V Supply Voltage VCC Current Consumption without Load ICC Activation Voltage VON Activation Voltage Range VONR Sustaining Voltage VSUS 8.0 -- 8.8 V RD 6.4 -- -- KΩ Output Voltage Swing VOUT -- VCC-3 -- V Short Circuit Current IOUT -- 35 -- mA Differential Resistance in Off Condition Vs = 8.8 to 26V RA=1KΩ Vs=26V AC Operation Output Frequency VCC =26V,R1=14KΩ fH1 fH1 VSCR =0V -- 2300 -- Hz fH2 fH2 VSCR =6V -- 1700 -- Hz R1=27KΩ to 1.7 KΩ 0.1 -- 15 KHz R1=14KΩ,C1=100nF -- 10 -- Hz fH1 Range Sweep Frequency fL 2/5 Version: B07 TS2418 Telephone Tone Ringer with Bridge Diode Test and Application Circuit . Description: The TS2418 tone ringer derives its power supply by rectifying the AC ringing signal. It uses this power to activate two tone generators. The two tone frequencies generated are switched by internal oscillator in a fast sequence and made audible across an output amplifier in the loudspeaker; both tone frequencies and the switching frequency can be externally adjusted. The device can drive either directly a piezo ceramic converter (buzzer) or small loudspeaker. In case of using a loudspeaker, a transformer is needed. An internal shunt voltage regulator provides DC voltage to the output stage, low frequency oscillator, and high f frequency oscillator. To protect the IC from telephone line transients, a zener Diode is included. 3/5 Version: B07 TS2418 Telephone Tone Ringer with Bridge Diode DIP-8 Mechanical Drawing DIM A B C D G J K L M DIP-8 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX 9.07 9.32 0.357 0.367 6.22 6.48 0.245 0.255 3.18 4.45 0.125 0.135 0.35 0.55 0.019 0.020 2.54 (typ) 0.10 (typ) 0.29 0.31 0.011 0.012 3.25 3.35 0.128 0.132 7.75 8.00 0.305 0.315 o o 10 10 Marking Diagram Y = Year Code M = Month Code (A=Jan, B=Feb, C=Mar, D=Apl, E=May, F=Jun, G=Jul, H=Aug, I=Sep, J=Oct, K=Nov, L=Dec) L = Lot Code 4/5 Version: B07 TS2418 Telephone Tone Ringer with Bridge Diode Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 5/5 Version: B07