TS3410 1A / 1.4MHz Synchronous Buck Converter SOT-25 Pin Definition: 1. EN 2. Ground 3. Switching Output 4. Input 5. Feedback General Description TS3410 is a high efficiency monolithic synchronous buck regulator using a constant frequency, current mode architecture. The device is available in an adjustable version. Supply current with no load is 250uA and drops to <1uA in shutdown. The 2.5V to 6V input voltage range makes TS3410 ideally suited for single Li-Ion, two to four AA battery-powered applications. 100% duty cycle provides low dropout operation, extending battery life in portable systems. PWM pulse skipping mode operation provides very low output ripple voltage for noise sensitive applications. Switching frequency is internally set at 1.4MHz, allowing the use of small surface mount inductors and capacitors. The internal synchronous switch increases efficiency and decreases need of an external Schottky diode. Low output voltages are easily supported with the 0.6V feedback reference voltage. Features Application ● ● ● ● ● ● ● ● ● ● ● ● ● ● ● High Efficiency: Up to 96% 2.5V to 6V Input Voltage Range Output Voltage from 0.6V to VIN Short Circuit Protection (SCP) Build in Soft-Start Function 1.4MHz Constant Frequency Operation Up to 1A Output Current Low Quiescent Current: 250uA (Typ.) No Schottky Diode Required in Application ≤1uA Shutdown Current Current Mode Operation for Excellent Line and Load Transient Response Cellular Phones Digital Still Cameras Portable Electronics USB Devices Pin Description Name Power-off pin H：normal operation L：Step-down operation stopped (All circuits deactivated) Ground pin Switch output pin. Connect external inductor here. Minimize trace area at this pin to reduce EMI. IC power supply pin Output Feedback pin EN GND Ordering Information SW Part No. Package Packing TS3410CX5 RF SOT-25 3Kpcs/ 7” Reel Description VCC FB Application Circuit VIN=2.5V~6V U1 VIN VOUT=1.8V L1 SW 2.7uH EN C1 4.7u GND AX3513 R1 600K FB VOUT = 0.6 * (1+R1/R2) R2=100K~330K 1/10 C3 15p C2 10u R2 300K Version: C08 TS3410 1A / 1.4MHz Synchronous Buck Converter Absolute Maximum Rating Characteristics Symbol Rating Unit VIN Pin Voltage VIN Gnd - 0.3 to Gnd + 6.5 V Feedback Pin Voltage VFB Gnd - 0.3 to VIN + 0.3 V RUN Pin Voltage VRUN Gnd - 0.3 to VIN + 0.3 V Switch Pin Voltage VSW Gnd - 0.3 to VIN + 0.3 V Peak SW Sink & Source Current IPSW 1.4 A Power Dissipation PD (TJ-TA) / θJA mW Storage Temperature Range TST -40 to +150 o -40 to +85 o +125 o Operating Temperature Range TOP Junction Temperature TJ θJC Thermal Resistance from Junction to case θJA Thermal Resistance from Junction to ambient C C C 110 o 250 o C/W C/W 2 Note1: θJA is measured with the PCB copper area of approximately 1 in (Multi-layer). that need connect to Gnd pin of the TS3410. Electrical Specifications (Ta = 25oC, VIN=VRUN=3.6V unless otherwise noted) Characteristics Symbol Feedback Voltage VFB Quiescent Current ICCQ Conditions Min Typ Max Units TA =25℃,IOUT=50mA 0.588 0.6 0.612 -40°C ≤TA≤ 85°C 0.582 0.6 0.618 VFB=0.5V -- 250 350 uA V Feedback Bias Current IFB VFB =0.65V -- -- ±30 nA Shutdown Supply Current ISD VRUN =0V -- 0.1 1 uA Maximum Output Current IOUT(MAX) VCC =3V, VOUT=1.8V 1 -- -- A 1.2 1.4 -- A Current Limit ILIMIT VCC =3V Line Regulation △VOUT/VOUT VCC = 2.5V~5.5V -- 0.04 0.4 % Load Regulation △VOUT/VOUT IOUT = 0.01 to 0.6A -- 0.5 -- % 1.1 1.4 1.7 MHz Oscillation Frequency FOSC SW pin RDS(ON) of P-CH MOSFET RDSON ISW = 500mA -- 0.3 0.4 Ω RDS(ON) of N-CH MOSFET RDSON Note 1 -- 0.25 0.35 Ω VOUT=3.3V,IOUT= 0.5A -- 94 -- % Efficiency EFFI EN pin logic Input Threshold Voltage VENL -- -- 0.4 VENH 1.5 -- --. EN Pin Input Current IEN -- ±0.1 ±1 uA Thermal shutdown TDS -- 140 -- °C V Thermal TSH -30 -°C shutdown Hysteresis Note 1: Guaranteed by Design Note 2: 100% production test at +25°C. Specifications over the temperature range are guaranteed by design and characterization. 2/10 Version: C08 TS3410 1A / 1.4MHz Synchronous Buck Converter Block Diagram VIN SLOPE COMP OSC + REF Isense AMP - 0.6V SET Soft-Star FB + - RESET Icomp + PWM LOGIC NON-OVERLAP CONTROL SW + Izero COMP - Over-Temperature and Short-Circuit Protection GND Enable Logic EN Function Description Operation TS3410 is a monolithic switching mode step-down DC-DC converter. It utilizes internal MOSFETs to achieve high efficiency and can generate very low output voltage by using internal reference at 0.6V. It operates at a fixed switching frequency, and uses the slope compensated current mode architecture. This step-down DC-DC Converter supplies minimum 1000mA output current at input voltage range from 2.5V to 5.5V. Current Mode PWM Control Slope compensated current mode PWM control provides stable switching and cycle-by-cycle current limit for excellent load and line transient responses and protection of the internal main switch (P-Ch MOSFET) and synchronous rectifier (N-CH MOSFET). During normal operation, the internal P-Ch MOSFET is turned on for a certain time to ramp the inductor current at each rising edge of the internal oscillator, and switched off when the peak inductor current is above the error voltage. The current comparator, ICOMP, limits the peak inductor current. When the main switch is off, the synchronous rectifier will be turned on immediately and stay on until either the inductor current starts to reverse, as indicated by the current reversal comparator, IZERO, or the beginning of the next clock cycle.. 3/10 Version: C08 TS3410 1A / 1.4MHz Synchronous Buck Converter Application Information Setting the Output Voltage Application circuit item shows the basic application circuit with TS3410 adjustable output version. The external resistor sets the output voltage according to the following formula: Table 1: Resistor Select for Output Voltage Setting VOUT R2 R1 1.2V 1.5V 1.8V 2.5V 3.3V 5V 300K 300K 300K 150K 120K 124K 300K 450K 600K 470K 540K 910K Inductor Selection For most designs, the TS3410 operates with inductors of 2.2µH to 3.3µH. Low inductance values are physically smaller but require faster switching, which results in some efficiency loss. The inductor value can be derived from the following formula: Table 2: Inductor Select for Output Voltage Setting (VIN=3.6V) VOUT 1.2V 1.5V 1.8V 2.5V Inductor 2.7uH 2.7uH Part Number 7440430027 7440430027 WE-TPC Note: Part Type MH or M (www.we-online.com) 2.7uH 2.2uH 7440430027 7440430022 Where is inductor Ripple Current. Large value inductors lower ripple current and small value inductors result in high ripple currents. Choose inductor ripple current approximately 20% of the maximum load current 1A, ∆IL=200mA. For output voltages above 2.0V, when light-load efficiency is important, the minimum recommended inductor is 2.7µH. For optimum voltage-positioning load transients, choose an inductor with DC series resistance in the 50mΩ to 150mΩ range. For higher efficiency at heavy loads (above 200mA), or minimal load regulation (but some transient overshoot), the resistance should be kept below 100mΩ. The DC current rating of the inductor should be at least equal to the maximum load current plus half the ripple current to prevent core saturation (1000mA+100mA) Input Capacitor Selection The input capacitor reduces the surge current drawn from the input and switching noise from the device. The input capacitor impedance at the switching frequency shall be less than input source impedance to prevent high frequency switching current passing to the input. A low ESR input capacitor sized for maximum RMS current must be used. Ceramic capacitors with X5R or X7R dielectrics are highly recommended because of their low ESR and small temperature coefficients. A 4.7µF ceramic capacitor for most applications is sufficient. Output Capacitor Selection The output capacitor is required to keep the output voltage ripple small and to ensure regulation loop stability. The output capacitor must have low impedance at the switching frequency. Ceramic capacitors with X5R or X7R dielectrics are recommended due to their low ESR and high ripple current. Compensation Capacitor Selection The compensation capacitors for increasing phase margin provide additional stability. It is required and more than 15pF. Please refer to demo board schematic for design. 4/10 Version: C08 TS3410 1A / 1.4MHz Synchronous Buck Converter Electrical Characteristics Curve Figure 1. Output Voltage vs. Input Voltage Figure 2. Current Limit vs. Input Voltage Figure 3. Quiescent Current vs. Input Voltage Figure 4. Threshold Voltage vs. Input Voltage Figure 5. Output Voltage vs. Temperature Figure 6. Quiescent Current vs. Temperature 5/10 Version: C08 TS3410 1A / 1.4MHz Synchronous Buck Converter Electrical Characteristics Curve Figure 7. Frequency vs. Temperature Figure 8. Efficiency vs. Output Current Figure 9. Efficiency vs. Output Current Figure 10. Power-On Waveform Figure 11. Power-On Waveform Figure 12. Enable-ON Waveform 6/10 Version: C08 TS3410 1A / 1.4MHz Synchronous Buck Converter Electrical Characteristics Curve Figure 13. Enable-ON Waveform Figure 14. Load Transient Figure 15. Load Transient Figure 16. TSD to Release Figure 17. TSD to Release 7/10 Version: C08 TS3410 1A / 1.4MHz Synchronous Buck Converter Application Information (Continue) Layout Guide 8/10 Version: C08 TS3410 1A / 1.4MHz Synchronous Buck Converter SOT-25 Mechanical Drawing DIM A+A1 B C D E E H L Ө1 S1 SOT-25 DIMENSION MILLIMETERS INCHES MIN MAX MIN MAX. 0.09 1.25 0.0354 0.0492 0.30 0.50 0.0118 0.0197 0.09 0.25 0.0035 0.0098 2.70 3.10 0.1063 0.1220 1.40 1.80 0.0551 0.0709 1.90 BSC 0.0748 BSC 2.40 3.00 0.09449 0.1181 0.35 BSC 0.0138 BSC 0º 10º 0º 10º 0.95 BSC 0.0374 BSC arking Diagram G6 = Device Code Y = Year Code A = 2010 1 = 2011 W = Week Code 01 ~ 26 (A~Z) 27 ~ 52 (a~z) X = Internal ID Code 9/10 Version: C08 TS3410 1A / 1.4MHz Synchronous Buck Converter Notice Specifications of the products displayed herein are subject to change without notice. TSC or anyone on its behalf, assumes no responsibility or liability for any errors or inaccuracies. Information contained herein is intended to provide a product description only. No license, express or implied, to any intellectual property rights is granted by this document. Except as provided in TSC’s terms and conditions of sale for such products, TSC assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of TSC products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright, or other intellectual property right. The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications. Customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify TSC for any damages resulting from such improper use or sale. 10/10 Version: C08