UTC TA8227AP LINEAR INTEGRATED CIRCUIT LOW FREQUENCY POWER AMPLIFIER DESCRIPTION The UTC TA8227AP is an audio power IC with built-in two channels developed for portable radio cassette tape recorder with power ON / OFF switch. Because of the parts reduction and DIP, space merit is remarkable. Thermal shut down protection circuit is built in. FEATURES *Wide operating supply voltage: Vcc=5~12V *Low popping noise at power ON DIP-12H *Best for supply voltage 9V *Output power Po=2.5W/CH at Vcc=9V, RL=4Ω, f=1kHz, THD=10% Po=3.0W/CH at Vcc=9V, RL=3Ω, f=1kHz, THD=10% *Soft Clip *Built-in Thermal shut-down protection circuit *Stand-by Switch BLOCK DIAGRAM UTC UNISONIC TECHNOLOGIES CO., LTD. 1 QW-R107-021,A UTC TA8227AP LINEAR INTEGRATED CIRCUIT APPLICATION INFORMATION AND APPLICATION METHOD 1. Adjustment of voltage gain The voltage gain Gv is obtained as follows by R1, R2 and Rf in Fig.1 When Rf=0Ω Gv=56.5 dB (Typ.) When Rf=120Ω Gv=45 dB (Typ.) By increasing Rf, reduction of Gv is possible. However, since the feedback increase is liable to produce oscillation, it is recommended to use this at 40dB or over. 2. Thermal shut-down circuit The thermal shut-down circuit is built in for the purpose of preventing the destruction of IC due to the abnormal temperature rise when the heat radiation is insufficient. The operation temperature is set at radiation Fin temperature 175°C (Typ.) At this temperature or over the bias is interrupted to prevent the destruction of IC. 3. Input stage The input circuit of this IC is as shown in fig.2. PNP Tr : Q1 is provided in the input circuit so as to make its usage possible without the input coupling capacitor. However, at pin 6 and pin 7, max 60mV offset voltage is produced. Application after checking volume slide noise is recommended. For cutting the volume slide noise, insert the input capacitor: CIN in series to interrupt the DC component. UTC UNISONIC TECHNOLOGIES CO., LTD. 2 QW-R107-021,A UTC TA8227AP LINEAR INTEGRATED CIRCUIT 4. Oscillation preventive measures For oscillation preventive capacitor C6 and C7 between the output terminal and GND, it is recommended to use polyester film capacitor having good characteristics for temperature and for high frequency. Since the characteristics of the capacitor is liable to be influenced by the temperature, use this capacitor after the temperature test to check the oscillation allowance. In addition, as the position of the electrolytic capacitor has a remarkable influence on the oscillation, connect C10 to Vcc at the nearest possible position from power GND. At using this application wth the voltage gain reduced, oscillation is liable to be produced. Apply the capacitor after checking enough for its capacity, type and mounting position. 5. Power ON / OFF switch There is power ON / OFF switch at Pin1. However, output power is changed by Pin1 supply voltage when Pin1 supply voltage is not same Pin12 supply voltage, after referring to attached date, select Pin1 supply voltage. 6. Input voltage When the excessive signal is input, turning-up is produced in the clip waveform. The turning-up point is Vin=300mVrms (Typ.) : Vcc=9V, RL=4Ω, f=1kHz : Enough care must be taken for this phenomenon. UTC UNISONIC TECHNOLOGIES CO., LTD. 3 QW-R107-021,A UTC TA8227AP LINEAR INTEGRATED CIRCUIT ABSOLUTE MAXIMUN RATINGS (Ta=25°C) PARAMETER Supply Voltage Output Current (peak / CH) Power Dissipation SYMBOL VALUE Vcc 20 UNIT V Io (peak) 2.5 A Pd 4.0 W Operating Temperature Topr -25~75 °C Storage Temperature Tstg -55~150 °C ELECTRICAL CHARACTERISTICS (Ta=25°C, Vcc=9V, RL=4Ω, Rg=600Ω, f=1kHz, unless otherwise specified) PARAMETER SYMBOL TEST CONDITIONS ICCQ Vin=0 Pout(1) THD=10% Pout(2) THD=10%, RL=3Ω 3.0 Total Harmonic Distortion THD Pout=0.4W/CH 0.2 1.0 % Voltage Gain Gv1 Rf=120Ω,Vout=0.775Vrms (0 dBm) 45 47 dB Gv2 Rf=0, Vout=0.775Vrms (0 dBm) 56.5 Rg=10kΩ,BW=20Hz~20kHz 0.3 1.0 mVrms Quiescent Current Output Power MIN 2.0 43 TYP MAX UNIT 21 45 mA 2.5 W Input Impedance Rin Output Noise Voltage Vno Ripple Rejection Ratio R.R. Rg=600Ω, fripple=100Hz -52 dB Cross Talk C.T Rg=600Ω,Vout=0.775Vrms (0 dBm) -50 dB Input Offset Voltage 30 V6, V7 Standby Current 30 1stb Sw1:OFF kΩ 60 mV µA 1 TYP. DC VOLTAGE OF EACH TERMINAL (Vcc=9V, Ta=25°C ) TERMINAL NO. DC VOLTAGE (V) UTC 1 Vcc 2 4.5 3 8.7 4 GND 5 0.7 6 0.03 7 0.03 8 0.7 9 5.0 10 8.7 11 4.5 UNISONIC TECHNOLOGIES CO., LTD. 12 Vcc 4 QW-R107-021,A UTC TA8227AP LINEAR INTEGRATED CIRCUIT TEST CIRCUIT Note 1: This IC can be used without coupling capacitor (CIN). If volume slide noise noise occurred by input offset voltage is undesirable, it needs to use the capacitor (CIN). Note 2: The condenser between the pin4 and the GND (C11) is for reducing pop noise when the power ON / OFF switch (SW1) is set to ON / OFF. UTC UNISONIC TECHNOLOGIES CO., LTD. 5 QW-R107-021,A UTC TA8227AP LINEAR INTEGRATED CIRCUIT UTC UNISONIC TECHNOLOGIES CO., LTD. 6 QW-R107-021,A UTC TA8227AP LINEAR INTEGRATED CIRCUIT UTC UNISONIC TECHNOLOGIES CO., LTD. 7 QW-R107-021,A UTC TA8227AP LINEAR INTEGRATED CIRCUIT UTC UNISONIC TECHNOLOGIES CO., LTD. 8 QW-R107-021,A UTC TA8227AP LINEAR INTEGRATED CIRCUIT UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UTC UNISONIC TECHNOLOGIES CO., LTD. 9 QW-R107-021,A