UNISONIC TECHNOLOGIES CO., LTD U74LVC2G240 CMOS IC DUAL BUFFER/DRIVER WITH 3-STATE OUTPUTS DESCRIPTION The U74LVC2G240 is a dual buffer or driver with 3-state outputs. It is designed for 1.65V to 5.5V operation. The U74LVC2G240 is composed of two 1-bit buffers/drivers with separate output-enable ( OE ) inputs. When OE is low, data passes from A (input) to Y (output). When OE is high, the outputs are in the high-impedance state. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pull-up resistor, and the minimum value of the resistor is determined by the current-sinking capability of the driver. The U74LVC2G240 is fully specified for partial-power-down applications using IOFF. The IOFF circuitry disables the outputs and prevents damaging current backflow through the device when it is powered down. TSSOP-8 FEATURES * Wide Supply Voltage Range from 1.65V to 5.5V * Max tPD of 4.6 ns at 3.3V * Up to 5.5V Inputs Accept Voltages * Low Power Consumption, ICC = 10 μA (Max.) * ±24 mA Output Driver at 3.3V * Typical VOLP (Output Ground Bounce) < 0.8V, VCC = 3.3 V, TA = 25 ℃ * Typical VOHV (Output VOH Undershoot) > 2V, VCC = 3.3 V, TA = 25 ℃ ORDERING INFORMATION Ordering Number U74LVC2G240G-P08-R Package TSSOP-8 U74LVC2G240G-P08-R (1) Packing Type Packing Tape Reel (1) R: Tape Reel (2) Package Type (2) P08:TSSOP-8 (3) Halogen Free (3) G: Halogen Free www.unisonic.com.tw Copyright © 2010 Unisonic Technologies Co., Ltd 1 of 6 QW-R502-433.A U74LVC2G240 CMOS IC PIN CONFIGURATION FUNCTION TABLE (Each Buffer) INPUTS A H L X OE L L H OUTPUT Y L H Z LOGIC DIAGRAM (Positive Logic) 1OE 1A 2OE 2A 1 2 1Y 7 5 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 3 2Y 2 of 6 QW-R502-433.A U74LVC2G240 CMOS IC ABSOLUTE MAXIMUM RATING PARAMETER SYMBOL RATINGS UNIT Supply Voltage VCC -0.5~6.5 V Input Voltage VIN -0.5~6.5 V Output Voltage VOUT -0.5~6.5 V (any output in the high-impedance or power-off state) Output Voltage VOUT -0.5~VCC+0.5 V (any output in the high or low state) Input Clamp Current IIK -50 mA Output Clamp Current IOK -50 mA Output Current IOUT ±50 mA VCC or GND Current ICC ±100 mA Storage Temperature TSTG -65 ~ +150 °C Note: 1. The input and output voltage ratings may be exceeded if the input and output current ratings are observed. 2. Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. THERMAL DATA PARAMETER Junction to Ambient SYMBOL θJA RATINGS 190 UNIT °C /W RECOMMENDED OPERATING CONDITIONS PARAMETER Supply Voltage High-Level Input Voltage SYMBOL VCC VIH Low-Level Input Voltage VIL Input Voltage VIN Output Voltage High-Level Output Current VOUT IOH CONDITIONS Operating Data retention only VCC = 1.65V to 1.95V VCC = 2.3V to 2.7V VCC = 3V to 3.6V VCC = 4.5V to 5.5V VCC = 1.65V to 1.95V VCC = 2.3V to 2.7V VCC = 3V to 3.6V VCC = 4.5V to 5.5V High or low state 3-state VCC=1.65V VCC=2.3V MIN 1.65 1.5 IOL Input Transition Rise or Fall Rate t R / tF Operating Temperature TOPR 1.7 2 www.unisonic.com.tw V 0.7* VCC 0.35* VCC 0.7 0.8 V 0.3* VCC 0 0 0 VCC=3V VCC=3V VCC=4.5V VCC=1.8±0.15V, 2.5±0.2V VCC=3.3±0.3V VCC=5.0+0.5V UNISONIC TECHNOLOGIES CO., LTD MAX UNIT 5.5 V 0.65* VCC VCC=4.5V VCC=1.65V VCC=2.3V Low-Level Output Current TYP -40 5.5 VCC 5.5 -4 -8 -16 -24 -32 4 8 16 24 32 20 10 5 85 V V mA mA ns/ V °C 3 of 6 QW-R502-433.A U74LVC2G240 CMOS IC ELECTRICAL CHARACTERISTICS (TA =25°C , VCC = 3.3 V, unless otherwise specified) PARAMETER High-Level Output Voltage Low-Level Output Voltage Input Leakage Current (A or OE inputs) OFF-State Current High-Impedance State Current Quiescent Supply Current SYMBOL VOH VOL II(LEAK) IOFF IOZ IQ Additional quiescent Supply Current Δ IQ Input Capacitance Output Capacitance CIN COUT MIN TYP VCC -0.1 1.2 1.9 2.4 2.3 3.8 MAX UNIT V 0.1 0.45 0.3 0.4 0.55 0.55 V VIN = 5.5V or GND, VCC = 0 to 5.5V ±5 μA VIN or VO = 5.5V, VCC = 0V VO = 0 to 5.5V, VCC = 3.6V VIN = 5.5V or GND, IOUT = 0, VCC = 1.65V to 5.5V One input at VCC – 0.6V; other inputs at VCC or GND; VCC=3V to 5.5V VIN = VCC or GND, VCC=3.3V VOUT = VCC or GND, VCC=3.3V ±10 10 μA μA 10 μA 500 μA 4 6 pF pF SWITCHING CHARACTERISTICS (TA =25°C) PARAMETER SYMBOL Propagation Delay from Input A to Output Y tPLH / tPHL (tPD) Propagation Delay from Input OE to Output Y tPZL / tPZH (tEN) Propagation Delay from Input OE to Output Y tPLZ / tPHZ (tDIS) TEST CONDITIONS IOH = -100 μA VCC = 1.65V to 5.5V IOH = -4 mA VCC = 1.65V IOH = -8 mA VCC = 2.3V IOH = -16 mA VCC = 3V IOH = -24 mA VCC = 3V IOH = -32 mA VCC = 4.5V IOL = 100 μA VCC = 1.65V to 5.5V IOL = 4 mA VCC = 1.65V IOL = 8 mA VCC = 2.3V IOL = 16 mA VCC = 3V IOL = 24 mA VCC = 3V IOL = 32 mA VCC = 4.5V TEST CONDITIONS VCC=1.8±0.15V, RL=1KΩ CL=30pF VCC=2.5±0.2V, RL=500Ω VCC=3.3±0.3V, RL=500Ω RL=500Ω CL=50pF VCC=5±0.5V, RL=500Ω VCC=1.8±0.15V, RL=1KΩ CL=30pF VCC=2.5±0.2V, RL=500Ω VCC=3.3±0.3V RL=500Ω CL=50pF VCC=5±0.5V VCC=1.8±0.15V, RL=1KΩ CL=30pF VCC=2.5±0.2V, RL=500Ω VCC=3.3±0.3V RL=500Ω CL=50pF VCC=5±0.5V MIN 2 1.4 TYP MAX UNIT 11.3 5.5 1.1 4.6 1 4 2.7 1.9 1.4 1.1 1.7 0.8 1.2 0.5 11.7 6.6 5.4 5 12.8 5.7 5.5 4.2 ns ns ns OPERATING CHARACTERISTICS (TA =25°C) PARAMETER Power Dissipation Capacitance per buffer/driver SYMBOL CPD TEST CONDITIONS VCC = 1.8V VCC = 2.5V Outputs enabled f=10MHz VCC = 3.3V VCC = 5V VCC = 1.8V VCC = 2.5V Outputs disabled f=10MHz VCC = 3.3V VCC = 5V UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw MIN TYP 15 17 1 1 2 2 MAX UNIT pF pF 4 of 6 QW-R502-433.A U74LVC2G240 CMOS IC TEST CIRCUIT AND WAVEFORMS TEST tPLH/tPHL tPLZ/tPZL tPHZ/tPZH INPUTS VCC 1.8V±0.15V 2.5V±0.2V 3.3V±0.3V 5V±0.5V VIN VCC VCC 3V VCC tR, tF ≤2ns ≤2ns ≤2.5ns ≤2.5ns S1 Open VLOAD GND VM VLOAD CL RL VΔ VCC/2 VCC/2 1.5V VCC/2 2*VCC 2*VCC 6V 2*VCC 30pF 30pF 50pF 50pF 1KΩ 500Ω 500Ω 500Ω 0.15V 0.15V 0.3V 0.3V Notes: 1. CL includes probe and jig capacitance. 2. All input pulses are supplied by generators having the following characteristics: PRR ≤10MHz, ZO = 50Ω. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 6 QW-R502-433.A U74LVC2G240 CMOS IC UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 6 QW-R502-433.A