Document 265-1 Power Chip Inductors – 0805PS Series • Shielded power chip inductors • Excellent current handling for a part this size For new designs, we recommend the EPL2010, EPL2014 or LPS3010 as an alternative to this series. They all offer better current handling, lower DCR, lower profile and a smaller footprint. We will continue to manufacture and support the 0805PS. Part number1 0805PS-102KL_ 0805PS-152KL_ 0805PS-272KL_ 0805PS-332KL_ 0805PS-392KL_ 0805PS-472KL_ 0805PS-562KL_ 0805PS-682KL_ 0805PS-103KL_ 0805PS-153KL_ 0805PS-223KL_ 0805PS-333KL_ 0805PS-473KL_ 0805PS-683KL_ 0805PS-823KL_ 0805PS-104KL_ 0805PS-124KL_ 0805PS-154KL_ 0805PS-224KL_ 0805PS-334KL_ L2 ±10% (µH) 1.0 1.5 2.7 3.3 3.9 4.7 5.6 6.8 10 15 22 33 47 68 82 100 120 150 220 330 DCR4 SRF5 Q min3 max typ at 1 MHz (Ohms) (MHz) 21 0.14 340 21 0.18 265 21 0.35 190 21 0.50 180 21 0.74 165 21 0.85 155 21 0.91 143 21 1.37 118 21 1.51 66 21 2.04 34 25 2.48 22 25 3.00 17 25 3.85 15 28 4.42 12 30 6.00 12 32 6.96 9.0 32 7.51 7.7 32 8.33 5.0 32 13.71 5.0 32 20.53 3.5 Isat6 (A) 0.90 0.85 0.60 0.55 0.50 0.43 0.38 0.32 0.27 0.22 0.18 0.16 0.15 0.12 0.11 0.10 0.10 0.08 0.07 0.06 Irms7 (A) 1.6 1.3 0.88 0.70 0.61 0.59 0.57 0.46 0.43 0.34 0.33 0.28 0.26 0.24 0.21 0.19 0.18 0.18 0.14 0.11 1. When ordering, please specify termination and packaging codes: 0805PS-334KLC Termination: L = RoHS compliant silver-palladium-platinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (1500 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (7500 parts per full reel). 2. Inductance measured at 100 kHz, 0.1 Vrms, using a Coilcraft SMD-A fixture in Agilent/HP 4263B LCR meter. 3. Q measured on an Agilent/HP 4291 with an Agilent/HP 16193 test fixture. 4. DCR measured on a micro-ohmmeter and a Coilcraft CCF840 test fixture. 5. SRF measured using an Agilent/HP 8753D network analyzer and a Coilcraft SMD-D test fixture. 6. DC current at which the inductance drops 10% (typ) from its value without current. 7. Current that causes a 40°C temperature rise from 25°C ambient. 8. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 265-1 Revised 08/18/09 Document 265-2 Power Chip Inductors - 0805PS Series Typical L vs Frequency Typical L vs Current 1000 1000 330 µH 330 µH 100 µH 10 µH 10 3.3 µH 1 µH 1 100 µH 100 Inductance (µH) Inductance (µH) 100 10 µH 10 3.3 µH 1 µH 1 0.1 0.1 0.01 1 0.1 10 1 100 10 Typical Q vs Frequency C D B F 70 H I 60 E A Q factor 50 330 µH I G 100 µH 1 µH 30 3.3 µH 10 µH A max 10 1 0.1 B max C max D E F G H I J 0.133 0.118 0.079 0.053 0.080 0.050 0.020 0.070 0.040 0.030 inches 3,38 mm 3,00 2,00 1,35 2,03 1,27 0,51 1,78 1,02 0,76 10 Frequency (MHz) Core material Ceramic/Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 57.6 – 62.4 mg Ambient temperature –40°C to +65°C with Irms current, +65°C to +105°C with derated current Storage temperature Component: –40°C to +105°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +100 to +250 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1500/7″reel; 7500/13″ reel Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 2.34 mm pocket depth PCB washing Only pure water or alcohol recommended Irms Derating 120 110 100 90 80 70 60 50 40 25°C 30 20 Recommended Land Pattern Terminal wraparound: approx 0.010/0,25 both ends 20 Percent of rated Irms J 40 0 1000 Current (mA) Frequency (MHz) 10 0 -40 -20 0 20 40 60 80 100 120 Ambient temperature (°C) Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 265-2 Revised 08/18/09