Document 438-1 Shielded Power Inductors – LPS3008 Series • Very low DCR; excellent current handling • Only 0.8 mm tall; 3.0 × 3.0 mm footprint Core material Ferrite Core and winding loss See www.coilcraft.com/coreloss Terminations RoHS compliant silver-palladium-platinum-glass frit. Other terminations available at additional cost. Weight 22 – 25 mg Ambient temperature –40°C to +85°C with Irms current, +85°C to +125°C with derated current Storage temperature Component: –40°C to +125°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 1000/7″ reel; 3500/13″ reel; Plastic tape: 12 mm wide, 0.23 mm thick, 8 mm pocket spacing, 1.37 mm pocket depth Recommended pick and place nozzle OD: 3 mm; ID: ≤ 1.5 mm PCB washing Only pure water or alcohol recommended DCR SRF max3 typ4 ±20% (µH) (Ohms) (MHz) Inductance2 Part number1 Isat (A)5 10% 20% 30% drop drop drop Irms (A)6 20°C 40°C rise rise LPS3008-561ML_ LPS3008-801ML_ LPS3008-102ML_ LPS3008-152ML_ LPS3008-222ML_ 0.56 0.80 1.0 1.5 2.2 0.072 0.092 0.125 0.134 0.175 330 255 220 170 150 1.8 1.6 1.3 1.1 1.0 2.0 1.7 1.4 1.3 1.1 2.1 1.8 1.5 1.3 1.1 1.4 1.1 0.90 0.87 0.85 2.0 1.6 1.3 1.2 1.1 LPS3008-332ML_ LPS3008-472ML_ LPS3008-562ML_ LPS3008-682ML_ LPS3008-822ML_ 3.3 4.7 5.6 6.8 8.2 0.285 0.350 0.450 0.500 0.600 114 87 78 75 61 0.81 0.68 0.62 0.58 0.52 0.86 0.73 0.67 0.61 0.56 0.88 0.74 0.70 0.63 0.58 0.74 0.68 0.58 0.50 0.45 0.95 0.80 0.73 0.67 0.60 LPS3008-103ML_ LPS3008-123ML_ LPS3008-183ML_ LPS3008-223ML_ LPS3008-333ML_ 10 12 18 22 33 0.650 0.790 1.25 1.50 2.30 56 49 38 35 23 0.46 0.45 0.35 0.29 0.27 0.51 0.48 0.38 0.33 0.30 0.52 0.50 0.40 0.34 0.31 0.42 0.38 0.33 0.29 0.25 0.56 0.50 0.44 0.38 0.32 LPS3008-473ML_ LPS3008-683ML_ LPS3008-104ML_ LPS3008-124ML_ LPS3008-154ML_ 47 68 100 120 150 3.00 4.75 6.85 7.00 8.00 21 18 14 13 11 0.22 0.18 0.15 0.084 0.080 0.23 0.19 0.16 0.094 0.088 0.24 0.20 0.16 0.10 0.092 0.21 0.175 0.160 0.140 0.130 0.27 0.23 0.21 0.190 0.175 LPS3008-184ML_ LPS3008-224ML_ LPS3008-334ML_ 180 220 330 9.00 11.5 18.0 10 9 7 0.070 0.078 0.082 0.120 0.160 0.067 0.073 0.076 0.100 0.145 0.059 0.064 0.066 0.090 0.130 1. Please specify termination and packaging codes: LPS3008-104MLC Termination: L = RoHS compliant silver-palladiumplatinum-glass frit. Special order: T = RoHS tin-silver-copper (95.5/4/0.5) or S = non-RoHS tin-lead (63/37). Packaging: C= 7″ machine-ready reel. EIA-481 embossed plastic tape (1000 parts per full reel). B= Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D= 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (3500 parts per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms using an Agilent/HP 4192A. Inductance at 1 MHz is the same for parts with SRF ≥10 MHz. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using an Agilent/HP 8753ES or equivalent. 5. DC current that causes the specified inductance drop from its value without current. 6. Current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Coilcraft Designer’s Kit C392 contains samples of 0.80 µH to 33 µH parts (3 each) from LPS3008, LPS3010 and LPS3015. Kit C401 contains samples of 0.56 µH to 33 µH parts (3 each) from LPS4012 and LPS4018. Kit C402 contains samples of 220 µH to 3300 µH parts (3 each) from all five series. For details of kit contents and to order, contact Coilcraft or visit http://order.coilcraft.com. Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Document 438-1 Revised 03/18/09 Document 438-2 Shielded SMT Power Inductors – LPS3008 Series Typical L vs Current Typical L vs Frequency 1000 1000 330 µH 100 µH 100 100 µH Inductance (µH) Inductance (µH) 330 µH 33 µH 10 10 µH 3.3 µH 1 0.1 1 0.1 33 µH 10 µH 10 3.3 µH 1.0 µH 1 1.0 µH 0.01 100 10 0.1 0.01 1 0.1 Current (A) 10 Frequency (MHz) 0.116 ±0.003* 2,95 ±0,076 Current Derating 120 100 XXX 90 80 0.116 ±0.003* 2,95 ±0,076 Winding direction 70 Dash number 60 50 40 30 20 Isat Irms 10 0 -40 -20 0 20 Recommended Land Pattern 0.0315 max 0,8 25°C Percent of rated Current 110 40 60 80 100 0.020 0,51 120 140 Ambient temperature (°C) 0.025 0,64 0.035 0,89 overall dimensions including the termination, add 0.005 in / 0,13 mm. Dimensions are in 0.130 3,30 0.040 1,02 are of the case not * Dimensions including the termination. For maximum 0.130 3,30 inches mm Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 0.045 1,14 Document 438-2 Revised 03/18/09