Document 568-1 Shielded Power Inductors – XPL7030 • • • • Large terminations for excellent thermal management Soft saturation makes them ideal for VRM/VRD applications. XPL7030-102 specified by NSC in AN-1900 as L1 XPL7030-682 specified by STMicro for the LED7707 Designer’s Kit C430 contains 3 each of all values Terminations RoHS compliant matte tin over nickel over copper. Other terminations available at additional cost. Weight 0.74 g Core and winding loss See www.coilcraft.com/coreloss Ambient temperature –40°C to +125°C. The part can be operated without damage as long as the part (ambient temperature plus temperature rise due to self heating) does not exceed +165°C Storage temperature Component: –40°C to +165°C. Packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) 38 per billion hours / 26,315,789 hours, calculated per Telcordia SR-332 Packaging 400/7″ reel; 1500/13″ reel Plastic tape: 16 mm wide, 0.35 mm thick, 12 mm pocket spacing, 3.3 mm pocket depth PCB washing Only pure water or alcohol recommended Part number1 XPL7030-131ML_ XPL7030-281ML_ XPL7030-471ML_ XPL7030-701ML_ XPL7030-102ML_ XPL7030-122ML_ XPL7030-152ML_ XPL7030-182ML_ XPL7030-222ML_ XPL7030-272ML_ XPL7030-332ML_ XPL7030-472ML_ XPL7030-682ML_ XPL7030-822ML_ XPL7030-103ML_ XPL7030-223ML_ Inductance2 ±20%(µH) 0.13 0.28 0.47 0.70 1.0 1.2 1.5 1.8 2.2 2.7 3.3 4.7 6.8 8.2 10 22 DCR (mOhms)3 typ max 1.94 2.13 3.05 3.36 4.18 4.59 5.40 5.94 6.70 7.37 10.50 11.55 12.10 13.31 17.20 18.92 19.31 21.24 20.66 22.72 25.15 27.66 40.10 44.11 58.50 64.35 62.20 68.42 88.30 97.13 191.0 210.0 SRF typ4 (MHz) 241 137 83 64 50 43 40 31 29 26 22 16 13 12 11 7.3 Isat (A)5 10% drop 20% drop 40 57 28 44 22 34 20 32 19.0 29 14.3 22.2 13.2 20.2 10.6 16.6 10.5 16.0 9.8 14.5 9.0 14.0 6.8 10.5 5.8 9.4 5.2 8.2 4.4 7.2 3.0 4.7 1. When ordering, please specify packaging code: Irms Testing XPL7030-103MLC Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (400 parts per full reel). B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead. D = 13″ machine-ready reel. EIA-481 embossed plastic tape. Factory order only, not stocked (1500 parts per full reel). 2. Inductance tested at 100 kHz, 0.1 Vrms, 0 Adc. 3. DCR measured on a micro-ohmmeter. 4. SRF measured using Agilent/HP 4395A or equivalent. 5. DC current at which the inductance drops the specified amount from its value without current. 6. Current that causes the specified temperature rise from 25°C ambient. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering. Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Irms (A)6 20°C rise 40°C rise 23.8 31.3 18.6 24.6 16.6 21.6 13.5 17.6 12.0 16.4 10.1 13.9 9.2 12.3 7.5 10.0 7.1 9.7 6.5 8.8 5.8 8.5 4.8 6.4 4.0 5.2 3.8 5.0 3.2 4.4 2.1 2.8 Irms testing was performed on 0.75 inch wide × 0.25 inch thick copper traces in still air. Temperature rise is highly dependent on many factors including pcb land pattern, trace size, and proximity to other components. Therefore temperature rise should be verified in application conditions. Document 568-1 Revised 10/15/09 Document 568-2 SMT Power Inductors – XPL7030 Series Typical L vs Current Typical L vs Frequency 100 100 22 µH 10 10 µH 10 Inductance (µH) Inductance (µH) 22 µH 10 µH 3.3 µH 1.0 µH 1 0.13 µH 0.1 3.3 µH 1.0 µH 1 0.13 µH 0.1 0.01 0.01 0.1 1 10 100 0.01 0.01 10 100 Frequency (MHz) Typical ESR vs Frequency 0.276 ±0.020 7,00 ±0,50 50 40 0.078 2,00 22 µH XXX Equivalent Series Resistance (Ohms) 1 0.1 Current (A) 0.276 ±0.008 7,00 ±0,20 30 10 µH 0.13 µH Dash number 20 3.3 µH 0.118 max 3,00 10 1.0 µH 0 0.1 1 10 0.182 4,62 0.094 2,40 Frequency (MHz) 0.236 6,00 0.260 6,60 0.118 3,00 0.079 2,00 Dimensions are in Specifications subject to change without notice. Please check our website for latest information. © Coilcraft, Inc. 2009 Recommended Land Pattern inches mm Document 568-2 Revised 09/22/09