MICROCHIP TC1313

TC1313
500 mA Synchronous Buck Regulator,
+ 300 mA LDO
Features
Description
• Dual-Output Regulator (500 mA Buck Regulator
and 300 mA Low-Dropout Regulator (LDO))
• Total Device Quiescent Current = 57 µA (Typical)
• Independent Shutdown for Buck and LDO
Outputs
• Both Outputs Internally Compensated
• Synchronous Buck Regulator:
- Over 90% Typical Efficiency
- 2.0 MHz Fixed-Frequency PWM
(Heavy Load)
- Low Output Noise
- Automatic PWM-to-PFM mode transition
- Adjustable (0.8V to 4.5V) and Standard
Fixed-Output Voltages (0.8V, 1.2V, 1.5V,
1.8V, 2.5V, 3.3V)
• Low-Dropout Regulator:
- Low-Dropout Voltage = 137 mV Typical @
200 mA
- Standard Fixed-Output Voltages
(1.5V, 1.8V, 2.5V, 3.3V)
• Small 10-pin 3x3 DFN or MSOP Package Options
• Operating Junction Temperature Range:
- -40°C to +125°C
• Undervoltage Lockout (UVLO)
• Output Short Circuit Protection
• Overtemperature Protection
The TC1313 device combines a 500 mA synchronous
buck regulator and 300 mA Low-Dropout Regulator
(LDO) to provide a highly integrated solution for
devices that require multiple supply voltages. The
unique combination of an integrated buck switching
regulator and low-dropout linear regulator provides the
lowest system cost for dual-output voltage applications
that require one lower processor core voltage and one
higher bias voltage.
Applications
•
•
•
•
•
Cellular Phones
Portable Computers
USB-Powered Devices
Handheld Medical Instruments
Organizers and PDAs
The 500 mA synchronous buck regulator switches at a
fixed frequency of 2.0 MHz when the load is heavy,
providing a low-noise, small-size solution. When the
load on the buck output is reduced to light levels, it
changes operation to a Pulse Frequency Modulation
(PFM) mode to minimize quiescent current draw from
the battery. No intervention is necessary for smooth
transition from one mode to another.
The LDO provides a 300 mA auxiliary output that
requires a single 1 µF ceramic output capacitor,
minimizing board area and cost. The typical dropout
voltage for the LDO output is 137 mV for a 200 mA
load.
The TC1313 device is available in either the 10-pin DFN
or MSOP package.
Additional protection features include: UVLO,
overtemperature and overcurrent protection on both
outputs.
For a complete listing of TC1313 standard parts,
consult your Microchip representative.
Package Type
10-Lead DFN *
SHDN2 1
VIN2 2
VOUT2 3
NC 4
AGND 5
10 PGND
EP
11
9 LX
8 VIN1
7 SHDN1
6 VFB1/VOUT1
10-Lead MSOP
SHDN2 1
VIN2 2
VOUT2 3
NC 4
AGND 5
10 PGND
9
8
7
6
LX
VIN1
SHDN1
VFB1/VOUT1
* Includes Exposed Thermal Pad (EP); see Table 3-1.
© 2009 Microchip Technology Inc.
DS21974B-page 1
TC1313
Functional Block Diagram
UVLO
Undervoltage Lockout
(UVLO)
VREF
Synchronous Buck Regulator
VIN1
PDRV
VIN2
LX
SHDN1
Driver
Control
NDRV
PGND
PGND
PGND
AGND
VOUT1/VFB1
VREF
UVLO
VOUT2
LDO
SHDN2
DS21974B-page 2
AGND
© 2009 Microchip Technology Inc.
TC1313
Typical Application Circuits
TC1313
Fixed-Output Application
10-Lead MSOP
4.7 µH
VIN
2.7V to 4.2V
8
4.7 µF
2
VIN1
LX
VIN2
7
SHDN1
1
SHDN2
VOUT2
4
4.7 µF
PGND 10
VOUT1
AGND
NC
VOUT1
1.5V @ 500 mA
9
6
3
5
VOUT2
1 µF
2.5V @ 300 mA
TC1313
Adjustable-Output Application
10-Lead DFN
Input
Voltage
4.5V to 5.5V
VIN1
4.7 µF
VIN2
SHDN1
*Optional
Capacitor
VIN2
1.0 µF
8
9
2
10
7
EP
11
6
SHDN2
1
3
NC
4
5
LX
PGND
4.7 µH
4.7 µF
VOUT1
200 kΩ
4.99 kΩ
2.1V @
500 mA
VOUT1
VOUT2
VOUT2
AGND
3.3V @
300 mA
1 µF
33 pF
121 kΩ
Note
Note: Connect DFN package exposed pad to AGND.
© 2009 Microchip Technology Inc.
DS21974B-page 3
TC1313
NOTES:
DS21974B-page 4
© 2009 Microchip Technology Inc.
TC1313
1.0
† Notice: Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied.
Exposure to maximum rating conditions for extended periods
may affect device reliability.
ELECTRICAL
CHARACTERISTICS
Absolute Maximum Ratings †
VIN - AGND ......................................................................6.0V
All Other I/O ...............................(AGND - 0.3V) to (VIN + 0.3V)
LX to PGND...............................................-0.3V to (VIN + 0.3V)
PGND to AGND .................................................. -0.3V to +0.3V
Output Short Circuit Current ................................ Continuous
Power Dissipation (Note 7) .......................... Internally Limited
Storage temperature .....................................-65°C to +150°C
Ambient Temp. with Power Applied ................-40°C to +85°C
Operating Junction Temperature...................-40°C to +125°C
ESD protection on all pins (HBM) ....................................... 3 kV
DC CHARACTERISTICS
Electrical Characteristics: VIN1 = VIN2 = SHDN1,2 = 3.6V, COUT1 = CIN = 4.7 µF, COUT2 = 1µF, L = 4.7 µH, VOUT1 (ADJ) = 1.8V,
IOUT1 = 100 ma, IOUT2 = 0.1 mA TA = +25°C. Boldface specifications apply over the TA range of -40°C to +85°C.
Parameters
Sym
Min
Typ
Max
Units
Conditions
Input/Output Characteristics
VIN
2.7
—
5.5
V
Maximum Output Current
IOUT1_MAX
500
—
—
mA
Maximum Output Current
IOUT2_MAX
300
—
—
mA
Note 1
IIN_SHDN
—
0.05
1
µA
SHDN1 = SHDN2 = GND
IQ
—
57
100
µA
SHDN1 = SHDN2 = VIN2
IOUT1 = 0 mA, IOUT2 = 0 mA
Synchronous Buck IQ
—
38
—
µA
SHDN1 = VIN, SHDN2 = GND
LDO IQ
—
44
—
µA
SHDN1 = GND, SHDN2 = VIN2
Input Voltage
Shutdown Current
Combined VIN1 and VIN2 Current
Operating IQ
Note 1, Note 2, Note 8
Note 1
Shutdown/UVLO/Thermal Shutdown Characteristics
SHDN1,SHDN2,
Logic Input Voltage Low
VIL
—
—
15
%VIN
VIN1 = VIN2 = 2.7V to 5.5V
SHDN1,SHDN2,
Logic Input Voltage High
VIH
45
—
—
%VIN
VIN1 = VIN2 = 2.7V to 5.5V
SHDN1,SHDN2,
Input Leakage Current
IIN
-1.0
±0.01
1.0
µA
VIN1 = VIN2 = 2.7V to 5.5V
SHDNX = GND
SHDNY = VIN
Note 6, Note 7
Thermal Shutdown
Thermal Shutdown Hysteresis
Undervoltage Lockout
(VOUT1 and VOUT2)
Undervoltage Lockout Hysteresis
Note 1:
2:
3:
4:
5:
6:
7:
8:
TSHD
—
165
—
°C
TSHD-HYS
—
10
—
°C
UVLO
2.4
2.55
2.7
V
UVLO-HYS
—
200
—
mV
VIN1 Falling
The Minimum VIN has to meet two conditions: VIN ≥ 2.7V and VIN ≥ VRX + VDROPOUT, VRX = VR1 or VR2.
VRX is the regulator output voltage setting.
TCVOUT2 = ((VOUT2max – VOUT2min) * 106)/(VOUT2 * DT).
Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested
over a load range from 0.1 mA to the maximum specified output current.
Dropout voltage is defined as the input-to-output voltage differential at which the output voltage drops 2% below its
nominal value measured at a 1V differential.
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction
temperature and the thermal resistance from junction to air. (i.e. TA, TJ, θJA). Exceeding the maximum allowable power
dissipation causes the device to initiate thermal shutdown.
The integrated MOSFET switches have an integral diode from the LX pin to VIN, and from LX to PGND. In cases where
these diodes are forward-biased, the package power dissipation limits must be adhered to. Thermal protection is not
able to limit the junction temperature for these cases.
VIN1 and VIN2 are supplied by the same input source.
© 2009 Microchip Technology Inc.
DS21974B-page 5
TC1313
DC CHARACTERISTICS (CONTINUED)
Electrical Characteristics: VIN1 = VIN2 = SHDN1,2 = 3.6V, COUT1 = CIN = 4.7 µF, COUT2 = 1µF, L = 4.7 µH, VOUT1 (ADJ) = 1.8V,
IOUT1 = 100 ma, IOUT2 = 0.1 mA TA = +25°C. Boldface specifications apply over the TA range of -40°C to +85°C.
Parameters
Sym
Min
Typ
Max
Units
Conditions
Synchronous Buck Regulator (VOUT1)
Adjustable Output Voltage Range
VOUT1
0.8
—
4.5
V
Adjustable Reference Feedback
Voltage (VFB1)
VFB1
0.78
0.8
0.82
V
Feedback Input Bias Current
(IFB1)
IVFB1
—
-1.5
—
nA
Output Voltage Tolerance Fixed
(VOUT1)
VOUT1
-2.5
±0.3
+2.5
%
Line Regulation (VOUT1)
VLINE-REG
—
0.2
—
%/V
Load Regulation (VOUT1)
VLOAD-REG
—
0.2
—
%
Dropout Voltage VOUT1
VIN – VOUT1
—
280
—
mV
FOSC
1.6
2.0
2.4
MHz
TSS
—
0.5
—
ms
TR = 10% to 90%
RDSon P-Channel
RDSon-P
—
450
—
mΩ
IP = 100 mA
RDSon N-Channel
RDSon-N
—
450
—
mΩ
IN = 100 mA
ILX
-1.0
±0.01
1.0
μA
SHDN = 0V, VIN = 5.5V, LX = 0V,
LX = 5.5V
+ILX(MAX)
—
700
—
mA
VOUT2
-2.5
±0.3
+2.5
%
Internal Oscillator Frequency
Start Up Time
LX Pin Leakage Current
Positive Current Limit Threshold
Note 2
VIN = VR+1V to 5.5V,
ILOAD = 100 mA
VIN = VR + 1.5V, ILOAD = 100 mA to
500 mA (Note 1)
IOUT1 = 500 mA, VOUT1 = 3.3V
(Note 5)
LDO Output (VOUT2)
Output Voltage Tolerance (VOUT2)
Note 2
Temperature Coefficient
TCVOUT
—
25
—
ppm/°C
Line Regulation
ΔVOUT2/
ΔVIN
-0.2
±0.02
+0.2
%/V
Load Regulation, VOUT2 ≥ 2.5V
ΔVOUT2/
IOUT2
-0.75
0.1
+0.75
%
IOUT2 = 0.1 mA to 300 mA (Note 4)
Load Regulation, VOUT2 < 2.5V
ΔVOUT2/
IOUT2
-0.90
0.1
+0.90
%
IOUT2 = 0.1 mA to 300 mA (Note 4)
Dropout Voltage VOUT2 > 2.5V
VIN – VOUT2
mV
IOUT2 = 200 mA (Note 5)
IOUT2 = 300 mA
f = 100 Hz, IOUT1 = IOUT2 = 50 mA,
CIN = 0 µF
Power Supply Rejection Ratio
Output Noise
Note 1:
2:
3:
4:
5:
6:
7:
8:
—
137
300
—
205
500
PSRR
—
62
—
dB
eN
—
1.8
—
µV/(Hz)½
Note 3
(VR+1V) ≤ VIN ≤ 5.5V
f = 1 kHz, IOUT2 = 50 mA,
SHDN1 = GND
The Minimum VIN has to meet two conditions: VIN ≥ 2.7V and VIN ≥ VRX + VDROPOUT, VRX = VR1 or VR2.
VRX is the regulator output voltage setting.
TCVOUT2 = ((VOUT2max – VOUT2min) * 106)/(VOUT2 * DT).
Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested
over a load range from 0.1 mA to the maximum specified output current.
Dropout voltage is defined as the input-to-output voltage differential at which the output voltage drops 2% below its
nominal value measured at a 1V differential.
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction
temperature and the thermal resistance from junction to air. (i.e. TA, TJ, θJA). Exceeding the maximum allowable power
dissipation causes the device to initiate thermal shutdown.
The integrated MOSFET switches have an integral diode from the LX pin to VIN, and from LX to PGND. In cases where
these diodes are forward-biased, the package power dissipation limits must be adhered to. Thermal protection is not
able to limit the junction temperature for these cases.
VIN1 and VIN2 are supplied by the same input source.
DS21974B-page 6
© 2009 Microchip Technology Inc.
TC1313
DC CHARACTERISTICS (CONTINUED)
Electrical Characteristics: VIN1 = VIN2 = SHDN1,2 = 3.6V, COUT1 = CIN = 4.7 µF, COUT2 = 1µF, L = 4.7 µH, VOUT1 (ADJ) = 1.8V,
IOUT1 = 100 ma, IOUT2 = 0.1 mA TA = +25°C. Boldface specifications apply over the TA range of -40°C to +85°C.
Parameters
Sym
Min
Typ
Max
Units
IOUTsc2
—
240
—
mA
RLOAD2 ≤ 1Ω
Wake-Up Time
(From SHDN2 mode), (VOUT2)
tWK
—
31
100
µs
IOUT1 = IOUT2 = 50 mA
Settling Time
(From SHDN2 mode), (VOUT2)
tS
—
100
—
µs
IOUT1 = IOUT2 = 50 mA
Output Short Circuit Current
(Average)
Note 1:
2:
3:
4:
5:
6:
7:
8:
Conditions
The Minimum VIN has to meet two conditions: VIN ≥ 2.7V and VIN ≥ VRX + VDROPOUT, VRX = VR1 or VR2.
VRX is the regulator output voltage setting.
TCVOUT2 = ((VOUT2max – VOUT2min) * 106)/(VOUT2 * DT).
Regulation is measured at a constant junction temperature using low duty cycle pulse testing. Load regulation is tested
over a load range from 0.1 mA to the maximum specified output current.
Dropout voltage is defined as the input-to-output voltage differential at which the output voltage drops 2% below its
nominal value measured at a 1V differential.
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction
temperature and the thermal resistance from junction to air. (i.e. TA, TJ, θJA). Exceeding the maximum allowable power
dissipation causes the device to initiate thermal shutdown.
The integrated MOSFET switches have an integral diode from the LX pin to VIN, and from LX to PGND. In cases where
these diodes are forward-biased, the package power dissipation limits must be adhered to. Thermal protection is not
able to limit the junction temperature for these cases.
VIN1 and VIN2 are supplied by the same input source.
TEMPERATURE SPECIFICATIONS
Electrical Specifications: Unless otherwise indicated, all limits are specified for: VIN = +2.7V to +5.5V
Parameters
Sym
Min
Typ
Max
Units
Conditions
Temperature Ranges
Operating Junction Temperature Range
TJ
-40
—
+125
°C
Storage Temperature Range
TA
-65
—
+150
°C
Steady state
Maximum Junction Temperature
TJ
—
—
+150
°C
Thermal Resistance, 10L-DFN
θJA
—
41
—
°C/W
Typical 4-layer board with Internal
Ground Plane and 2 Vias in Thermal
Pad
Thermal Resistance, 10L-MSOP
θJA
—
113
—
°C/W
Typical 4-layer board with Internal
Ground Plane
Transient
Thermal Package Resistances
© 2009 Microchip Technology Inc.
DS21974B-page 7
TC1313
2.0
TYPICAL PERFORMANCE CURVES
Note:
The graphs and tables provided following this note are a statistical summary based on a limited number of
samples and are provided for informational purposes only. The performance characteristics listed herein
are not tested or guaranteed. In some graphs or tables, the data presented may be outside the specified
operating range (e.g., outside specified power supply range) and therefore outside the warranted range.
IQ Switcher and LDO (µA)
66
64
SHDN1 = VIN2
SHDN2 = VIN2
VIN = 5.5V
62
60
VIN = 4.2V
58
56
VIN = 3.6V
54
VOUT1 Efficiency (%)
Note: Unless otherwise indicated, VIN1 = VIN2 = SHDN1,2 = 3.6V, COUT1 = CIN = 4.7 µF, COUT2 = 1 µF, L = 4.7 µH,
VOUT1 (ADJ) = 1.8V, TA = +25°C. Boldface specifications apply over the TA range of -40°C to +85°C. TA = +25°C. Adjustable or fixedoutput voltage options can be used to generate the Typical Performance Characteristics.
52
-40 -25 -10
5
100
95
90
85
80
75
70
65
60
55
50
20 35 50 65 80 95 110 125
IOUT1 = 250 mA
IOUT1 = 500 mA
2.7
3.05
3.4
Ambient Temperature (°C)
4.8
5.15
5.5
VOUT1 Efficiency(%)
VIN = 4.2V
34
VIN = 3.6V
5
95
90
85
VIN1 = 3.6V
80
VIN1 = 4.2V
75
VIN1 = 3.0V
70
0.005
30
-40 -25 -10
SHDN1 = VIN2
SHDN2 = AGND
VIN = 5.5V
32
20 35 50 65 80 95 110 125
0.104
0.203
0.302
FIGURE 2-2:
IQ Switcher Current vs.
Ambient Temperature.
100
SHDN1 = AGND
SHDN2 = VIN2
VIN = 5.5V
VIN = 4.2V
42
40
VIN = 3.6V
38
VOUT1 Efficiency(%)
95
44
0.5
FIGURE 2-5:
VOUT1 Output Efficiency vs.
IOUT1 (VOUT1 = 1.2V).
50
46
0.401
IOUT1 (A)
Ambient Temperature (°C)
IQ LDO (µA)
4.45
100
SHDN1 = VIN2
SHDN2 = AGND
36
48
4.1
FIGURE 2-4:
VOUT1 Output Efficiency vs.
Input Voltage (VOUT1 = 1.2V).
40
IQ Switcher (µA)
3.75
Input Voltage (V)
FIGURE 2-1:
IQ Switcher and LDO
Current vs. Ambient Temperature.
38
SHDN1 = VIN2
SHDN2 = AGND
IOUT1 = 100 mA
SHDN1 = VIN2
SHDN2 = AGND
IOUT1 = 100 mA
90
IOUT1 = 250 mA
85
80
IOUT1 = 500 mA
75
70
65
36
60
-40 -25 -10
5
20 35 50 65 80 95 110 125
Ambient Temperature (°C)
FIGURE 2-3:
Temperature.
DS21974B-page 8
IQ LDO Current vs. Ambient
2.7
3.05
3.4
3.75
4.1
4.45
4.8
5.15
5.5
Input Voltage (V)
FIGURE 2-6:
VOUT1 Output Efficiency vs.
Input Voltage (VOUT1 = 1.8V).
© 2009 Microchip Technology Inc.
TC1313
Note: Unless otherwise indicated, VIN1 = VIN2 = SHDN1,2 = 3.6V, COUT1 = CIN = 4.7 µF, COUT2 = 1 µF, L = 4.7 µH,
VOUT1 (ADJ) = 1.8V, TA = +25°C. Boldface specifications apply over the TA range of -40°C to +85°C. TA = +25°C. Adjustable or fixedoutput voltage options can be used to generate the Typical Performance Characteristics.
1.21
SHDN1 = VIN2
SHDN2 = AGND
VIN = 3.0V
95
90
VIN = 4.2V
85
80
0.104
0.203
0.302
0.401
VIN1 = 3.6V
1.202
1.198
1.194
VIN = 3.6V
75
0.005
SHDN1 = VIN2
SHDN2 = AGND
1.206
VOUT1 (V)
VOUT1 Efficiency(%)
100
1.19
0.005
0.5
0.104
IOUT1 (A)
1.82
SHDN1 = VIN2
SHDN2 = AGND
IOUT1 = 100 mA
IOUT1 = 250 mA
88
IOUT1 = 500 mA
1.81
1.805
1.8
1.795
80
3.60
3.92
4.23
4.55
4.87
5.18
1.79
0.005
5.50
0.104
0.203
0.302
FIGURE 2-8:
VOUT1 Output Efficiency vs.
Input Voltage (VOUT1 = 3.3V).
FIGURE 2-11:
(VOUT1 = 1.8V).
3.4
VIN1 = 3.6V
SHDN1 = VIN2
SHDN2 = AGND
3.36
VIN1 = 4.2V
75
VOUT1 (V)
90
SHDN1 = VIN2
SHDN2 = AGND
80
0.5
VOUT1 vs. IOUT1
95
85
0.401
IOUT1 (A)
Input Voltage (V)
VOUT1 Efficiency (%)
0.5
SHDN1 = VIN2
SHDN2 = AGND
VIN1 = 3.6V
1.815
84
100
0.401
VOUT1 vs. IOUT1
FIGURE 2-10:
(VOUT1 = 1.2V).
VOUT1 (V)
VOUT1 Efficiency (%)
100
92
0.302
IOUT1 (A)
FIGURE 2-7:
VOUT1 Output Efficiency vs.
IOUT1 (VOUT1 = 1.8V).
96
0.203
VIN1 = 5.5V
70
VIN1 = 4.2V
3.32
3.28
3.24
65
60
0.005
0.104
0.203
0.302
0.401
0.5
3.2
0.005
0.104
IOUT1 (A)
FIGURE 2-9:
VOUT1 Output Efficiency vs.
IOUT1 (VOUT1 = 3.3V).
© 2009 Microchip Technology Inc.
0.203
0.302
0.401
0.5
IOUT1 (A)
FIGURE 2-12:
(VOUT1 = 3.3V).
VOUT1 vs. IOUT1
DS21974B-page 9
TC1313
SHDN1 = VIN2
SHDN2 = AGND
2.15
2.10
2.05
2.00
1.95
1.90
2.7
3.1
3.5
3.9
4.3
4.7
5.1
0.65
0.55
P-Channel
0.50
N-Channel
0.45
0.40
3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5
5.5
Input Voltage (V)
Input Voltage (V)
FIGURE 2-13:
vs. Input Voltage.
VOUT1 Switching Frequency
SHDN1 = VIN2
SHDN2 = AGND
1.98
Buck Regulator Switch
Resistance (:)
1.96
1.94
1.92
VIN1 = 3.6V
0.65
P-Channel
0.60
N-Channel
0.55
0.50
SHDN1 = VIN2
SHDN2 = AGND
0.45
0.40
125
110
95
80
65
50
35
5
20
-10
-25
-40
1.90
-40 -25 -10
SHDN1 = VIN2
SHDN2 = AGND
VIN1 = 3.6V
0.810
0.805
0.800
0.795
0.4
SHDN1 = VIN2
SHDN2 = AGND
0.35
0.3
0.25
0.2
VOUT1 = 3.3V
IOUT1 = 500 mA
0.15
FIGURE 2-15:
VOUT1 Adjustable Feedback
Voltage vs. Ambient Temperature.
DS21974B-page 10
125
110
95
80
65
50
35
-10
125
110
95
80
65
50
35
20
5
-10
-25
-40
Ambient Temperature (°C)
-25
0.1
0.790
-40
VOUT1 FB Voltage (V)
20 35 50 65 80 95 110 125
FIGURE 2-17:
VOUT1 Switch Resistance
vs. Ambient Temperature.
VOUT1 Dropout Voltage (V)
FIGURE 2-14:
VOUT1 Switching Frequency
vs. Ambient Temperature.
0.815
5
Ambient Temperature (°C)
Ambient Temperature (°C)
0.820
VOUT1 Switch Resistance
5
VOUT1 Frequency (MHz)
FIGURE 2-16:
vs. Input Voltage.
0.70
2.00
SHDN1 = VIN2
SHDN2 = AGND
VIN1 = 3.6V
0.60
20
VOUT1 Frequency (MHz)
2.20
VOUT1 Switch Resistance (:)
Note: Unless otherwise indicated, VIN1 = VIN2 = SHDN1,2 = 3.6V, COUT1 = CIN = 4.7 µF, COUT2 = 1 µF, L = 4.7 µH,
VOUT1 (ADJ) = 1.8V, TA = +25°C. Boldface specifications apply over the TA range of -40°C to +85°C. TA = +25°C. Adjustable or fixedoutput voltage options can be used to generate the Typical Performance Characteristics.
Ambient Temperature (°C)
FIGURE 2-18:
VOUT1 Dropout Voltage vs.
Ambient Temperature.
© 2009 Microchip Technology Inc.
TC1313
Note: Unless otherwise indicated, VIN1 = VIN2 = SHDN1,2 = 3.6V, COUT1 = CIN = 4.7 µF, COUT2 = 1 µF, L = 4.7 µH,
VOUT1 (ADJ) = 1.8V, TA = +25°C. Boldface specifications apply over the TA range of -40°C to +85°C. TA = +25°C. Adjustable or fixedoutput voltage options can be used to generate the Typical Performance Characteristics.
VOUT2 Output Voltage (V)
1.802
IOUT2 = 150 mA
1.800
SHDN1 = AGND
SHDN2 = VIN2
TA = + 85°C
1.798
TA = + 25°C
1.796
TA = - 40°C
1.794
1.792
2.7 3.05 3.4 3.75 4.1 4.45 4.8 5.15 5.5
Input Voltage (V)
FIGURE 2-19:
VOUT1 and VOUT2 Heavy
Load Switching Waveforms vs. Time.
FIGURE 2-22:
VOUT2 Output Voltage vs.
Input Voltage (VOUT2 = 1.8V).
VOUT2 Output Voltage (V)
2.508
SHDN1 = AGND
SHDN2 = VIN2
IOUT2 = 150 mA
2.506
TA = + 85°C
2.504
2.502
TA = + 25°C
2.500
2.498
TA = - 40°C
2.496
3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5
Input Voltage (V)
FIGURE 2-20:
VOUT1 and VOUT2 Light
Load Switching Waveforms vs. Time.
IOUT2 = 150 mA
3.298
TA = + 85°C
1.49
1.488
TA = + 25°C
SHDN1 = AGND
SHDN2 = VIN2
1.486
TA = - 40°C
1.484
1.482
2.7
3.05
3.4
3.75
4.1
4.45
4.8
5.15
5.5
Input Voltage (V)
FIGURE 2-21:
VOUT2 Output Voltage vs.
Input Voltage (VOUT2 = 1.5V).
© 2009 Microchip Technology Inc.
VOUT2 Output Voltage (V)
1.492
VOUT2 Output Voltage(V)
FIGURE 2-23:
VOUT2 Output Voltage vs.
Input Voltage (VOUT2 = 2.5V).
SHDN1 = AGND
SHDN2 = VIN2
IOUT2 = 150 mA
3.297
TA = + 85°C
3.296
3.295
TA = + 25°C
3.294
TA = - 40°C
3.293
3.292
3.60
3.92
4.23
4.55
4.87
5.18
5.50
Input Voltage (V)
FIGURE 2-24:
VOUT2 Output Voltage vs.
Input Voltage (VOUT2 = 3.3V).
DS21974B-page 11
TC1313
SHDN1 = AGND
SHDN2 = VIN2
0.25
IOUT2 = 300 mA
0.20
IOUT2 = 200 mA
0.15
0.10
0.05
0.1
VIN2 = 3.6V
-0.1
-0.2
VOUT2 = 2.6V
VOUT2 = 1.5V
-0.3
FIGURE 2-25:
VOUT2 Dropout Voltage vs.
Ambient Temperature (VOUT2 = 2.5V).
IOUT2 = 200 mA
125
110
95
80
65
50
0
-10
VOUT2 PSRR (dB)
VOUT2 Dropout Voltage (V)
0.1
35
FIGURE 2-28:
VOUT2 Load Regulation vs.
Ambient Temperature.
SHDN1 = AGND
SHDN2 = VIN2
IOUT2 = 300 mA
20
Ambient Temperature (°C)
0.3
0.2
5
-10
-40
125
110
95
80
65
50
35
5
20
-10
-25
-40
-0.4
Ambient Temperature (°C)
-20
-30
SHDN1 = GND
VOUT2 = 1.5V
IOUT2 = 30 mA
CIN = 0 µF
COUT2 = 1.0 µF
-40
-50
COUT2 = 4.7 µF
-60
-70
-80
0.01
0.0
-40 -25 -10
5
20 35 50 65 80 95 110 125
0.1
FIGURE 2-26:
VOUT2 Dropout Voltage vs.
Ambient Temperature (VOUT2 = 3.3V).
0.000
VOUT2 = 3.3V
SHDN1 = AGND
SHDN2 = VIN2
-0.005
VOUT2 = 2.5V
-0.015
-0.020
-0.025
VOUT2 = 1.5V
-0.030
-0.035
-40 -25 -10
5
20 35 50 65 80 95 110 125
FIGURE 2-27:
VOUT2 Line Regulation vs.
Ambient Temperature.
1000
SHDN1 = AGND
SHDN2 = VIN2
1
0.1
VIN = 3.6V
VOUT2 = 2.5V
IOUT2 = 50 mA
0.01
0.01
0.1
1
10
100
1000
10000
Frequency (kHz)
Ambient Temperature (°C)
DS21974B-page 12
100
10
IOUT2 = 100 µA
-0.010
10
FIGURE 2-29:
VOUT2 Power Supply Ripple
Rejection vs. Frequency.
VOUT2 Noise (µV/—Hz)
0.005
1
Frequency (kHz)
Ambient Temperature (°C)
VOUT2 Line Regulation (%/V)
SHDN1 = AGND
SHDN2 = VIN2
VOUT2 = 3.3V
0.0
-25
VOUT2 Dropout Voltage (V)
0.30
VOUT2 Load Regulation (%)
Note: Unless otherwise indicated, VIN1 = VIN2 = SHDN1,2 = 3.6V, COUT1 = CIN = 4.7 µF, COUT2 = 1 µF, L = 4.7 µH,
VOUT1 (ADJ) = 1.8V, TA = +25°C. Boldface specifications apply over the TA range of -40°C to +85°C. TA = +25°C. Adjustable or fixedoutput voltage options can be used to generate the Typical Performance Characteristics.
FIGURE 2-30:
VOUT2 Noise vs. Frequency.
© 2009 Microchip Technology Inc.
TC1313
Note: Unless otherwise indicated, VIN1 = VIN2 = SHDN1,2 = 3.6V, COUT1 = CIN = 4.7 µF, COUT2 = 1 µF, L = 4.7 µH,
VOUT1 (ADJ) = 1.8V, TA = +25°C. Boldface specifications apply over the TA range of -40°C to +85°C. TA = +25°C. Adjustable or fixedoutput voltage options can be used to generate the Typical Performance Characteristics.
FIGURE 2-31:
vs. Time.
VOUT1 Load Step Response
FIGURE 2-34:
Waveforms.
VOUT1 and VOUT2 Startup
FIGURE 2-32:
vs. Time.
VOUT2 Load Step Response
FIGURE 2-35:
Waveforms.
VOUT1 and VOUT2 Shutdown
FIGURE 2-33:
VOUT1 and VOUT2 Line Step
Response vs. Time.
© 2009 Microchip Technology Inc.
DS21974B-page 13
TC1313
NOTES:
DS21974B-page 14
© 2009 Microchip Technology Inc.
TC1313
3.0
PIN DESCRIPTIONS
The descriptions of the pins are listed in Table 3-1.
TABLE 3-1:
PIN FUNCTION TABLE
Pin
DFN
MSOP
1
SHDN2
SHDN2
2
VIN2
VIN2
3
VOUT2
VOUT2
4
NC
NC
5
AGND
AGND
6
VFB / VOUT1
VFB / VOUT1
7
SHDN1
SHDN1
8
VIN1
VIN1
9
LX
LX
10
PGND
PGND
11
EP
—
3.1
Function
Active Low Shutdown Input for LDO Output Pin
Analog Input Supply Voltage Pin
LDO Output Voltage Pin
No Connect
Analog Ground Pin
Buck Feedback Voltage (Adjustable Version)/Buck Output Voltage (Fixed
Version) Pin
Active Low Shutdown Input for Buck Regulator Output Pin
Buck Regulator Input Voltage Pin
Buck Inductor Output Pin
Power Ground Pin
Exposed Pad. It is a thermal path to remove heat from the device. Electrically, this pad is at ground potential and should be connected to AGND.
LDO Shutdown Input Pin (SHDN2)
SHDN2 is a logic-level input used to turn the LDO
regulator on and off. A logic-high (> 45% of VIN) will
enable the regulator output. A logic-low (< 15% of VIN)
will ensure that the output is turned off.
3.2
LDO Input Voltage Pin (VIN2)
3.7
Buck Regulator Shutdown Input
Pin (SHDN1)
SHDN1 is a logic-level input used to turn the buck
regulator on and off. A logic-high (> 45% of VIN) will
enable the regulator output. A logic-low (< 15% of VIN)
will ensure that the output is turned off.
3.8
Buck Regulator Input Voltage Pin
(VIN1)
VIN2 is a LDO power-input supply pin. Connect
variable-input voltage source to VIN2. Connect VIN1 and
VIN2 together with board traces as short as possible.
VIN2 provides the input voltage for the LDO regulator.
An additional capacitor can be added to lower the LDO
regulator input ripple voltage.
VIN1 is the buck regulator power-input supply pin.
Connect a variable-input voltage source to VIN1.
Connect VIN1 and VIN2 together with board traces as
short as possible.
3.3
3.9
LDO Output Voltage Pin (VOUT2)
Buck Inductor Output Pin (LX)
VOUT2 is a regulated LDO output voltage pin. Connect
a 1 µF or larger capacitor to VOUT2 and AGND for proper
operation.
Connect LX directly to the buck inductor. This pin
carries large signal-level current; all connections
should be made as short as possible.
3.4
3.10
No Connect Pin (NC)
No connection.
Power Ground Pin (PGND)
AGND is the analog ground connection. Tie AGND to the
analog portion of the ground plane (AGND). See the
physical layout information in Section 5.0 “Application
Circuits/Issues” for grounding recommendations.
Connect all large-signal level ground returns to PGND.
These large-signal level ground traces should have a
small loop area and length to prevent coupling of
switching noise to sensitive traces. Please see the
physical layout information supplied in Section 5.0
“Application
Circuits/Issues” for
grounding
recommendations.
3.6
3.11
3.5
Analog Ground Pin (AGND)
Buck Regulator Output Sense Pin
(VFB/VOUT1)
For VOUT1 adjustable-output voltage options, connect
the center of the output voltage divider to the VFB pin.
For fixed-output voltage options, connect the output of
the buck regulator to this pin (VOUT1).
© 2009 Microchip Technology Inc.
Exposed Pad (EP)
For the DFN package, connect the EP to AGND with
vias into the AGND plane.
DS21974B-page 15
TC1313
NOTES:
DS21974B-page 16
© 2009 Microchip Technology Inc.
TC1313
4.0
DETAILED DESCRIPTION
4.2.1
4.1
Device Overview
While operating in Pulse Width Modulation (PWM)
mode, the TC1313 buck regulator switches at a fixed
2.0 MHz frequency. The PWM mode is suited for higher
load current operation, maintaining low output noise
and high conversion efficiency. PFM to PWM mode
transition is initiated for any of the following conditions.
The TC1313 combines a 500 mA synchronous buck
regulator with a 300 mA LDO. This unique combination
provides a small, low-cost solution for applications that
require two or more voltage rails. The buck regulator
can deliver high-output current over a wide range of
input-to-output voltage ratios while maintaining high
efficiency. This is typically used for the lower-voltage,
higher-current processor core. The LDO is a minimal
parts-count solution (single-output capacitor), providing
a regulated voltage for an auxiliary rail. The typical LDO
dropout voltage (137 mV @ 200 mA) allows the use of
very low input-to-output LDO differential voltages,
minimizing the power loss internal to the LDO pass
transistor. Integrated features include independent
shutdown
inputs,
UVLO,
overcurrent
and
overtemperature shutdown.
4.2
Synchronous Buck Regulator
The synchronous buck regulator is capable of supplying a 500 mA continuous output current over a wide
range of input and output voltages. The output voltage
range is from 0.8V (min) to 4.5V (max). The regulator
operates in three different modes and automatically
selects the most efficient mode of operation. During
heavy load conditions, the TC1313 buck converter
operates at a high, fixed frequency (2.0 MHz) using
current mode control. This minimizes output ripple and
noise (less than 8 mV peak-to-peak ripple) while maintaining high efficiency (typically > 90%). For standby or
light-load applications, the buck regulator will automatically switch to a power-saving Pulse Frequency
Modulation (PFM) mode. This minimizes the quiescent
current draw on the battery while keeping the buck
output voltage in regulation. The typical buck PFM
mode current is 38 µA. The buck regulator is capable of
operating at 100% duty cycle, minimizing the voltage
drop from input to output for wide-input, batterypowered applications. For fixed-output voltage applications, the feedback divider and control loop compensation components are integrated, eliminating the need
for external components. The buck regulator output is
protected against overcurrent, short circuit and overtemperature. While shut down, the synchronous buck
N-channel and P-channel switches are off, so the LX
pin is in a high-impedance state (this allows for
connecting a source on the output of the buck regulator
as long as its voltage does not exceed the input
voltage).
© 2009 Microchip Technology Inc.
FIXED-FREQUENCY PWM MODE
• Continuous inductor current is sensed
• Inductor peak current exceeds 100 mA
• The buck regulator output voltage has dropped
out of regulation (step load has occurred)
The typical PFM-to-PWM threshold is 80 mA.
4.2.2
PFM MODE
PFM mode is entered when the output load on the buck
regulator is very light. Once detected, the converter
enters the PFM mode automatically and begins to skip
pulses to minimize unnecessary quiescent current
draw by reducing the number of switching cycles per
second. The typical quiescent current for the switching
regulator is less than 38 µA. The transition from PWM
to PFM mode occurs when discontinuous inductor
current is sensed, or the peak inductor current is less
than 60 mA (typ.). The typical PWM to PFM mode
threshold is 30 mA. For low input-to-output differential
voltages, the PWM to PFM mode threshold can be low
due to the lack of ripple current. It is recommended that
VIN1 be one volt greater than VOUT1 for PWM to PFM
transitions.
4.3
Low-Dropout Regulator (LDO)
The LDO output is a 300 mA low-dropout linear
regulator that provides a regulated output voltage with
a single 1 µF external capacitor. The output voltage is
available in fixed options only, ranging from 1.5V to
3.3V. The LDO is stable using ceramic output
capacitors that inherently provide lower output noise
and reduce the size and cost of the regulator solution.
The quiescent current consumed by the LDO output is
typically less than 43.7 µA, with a typical dropout
voltage of 137 mV at 200 mA. The LDO output is
protected against overcurrent and overtemperature.
While operating in Dropout mode, the LDO quiescent
current will increase, minimizing the necessary voltage
differential needed for the LDO output to maintain
regulation. The LDO output is protected against overcurrent and overtemperature.
4.4
Soft Start
Both outputs of the TC1313 are controlled during
startup. Less than 1% of VOUT1 or VOUT2 overshoot is
observed during start-up from VIN rising above the
UVLO voltage; or SHDN1 or SHDN2 being enabled.
DS21974B-page 17
TC1313
4.5
Overtemperature Protection
The TC1313 has an integrated overtemperature
protection circuit that monitors the device junction
temperature and shuts the device off if the junction
temperature exceeds the typical 165°C threshold. If the
overtemperature threshold is reached, the soft start is
reset so that, once the junction temperature cools to
approximately 155°C, the device will automatically
restart.
DS21974B-page 18
© 2009 Microchip Technology Inc.
TC1313
5.0
APPLICATION CIRCUITS/
ISSUES
5.1
Typical Applications
The TC1313 500 mA buck regulator + 300 mA LDO
operates over a wide input-voltage range (2.7V to 5.5V)
and is ideal for single-cell Li-Ion battery-powered
applications, USB-powered applications, three-cell
NiMH or NiCd applications and 3V to 5V regulated
input applications. The 10-pin MSOP and 3x3 DFN
packages provide a small footprint with minimal external components.
5.2
Fixed-Output Application
A typical VOUT1 fixed-output voltage application is
shown in “Typical Application Circuits”. A 4.7 µF
VIN1 ceramic input capacitor, 4.7 µF VOUT1 ceramic
capacitor, 1.0 µF ceramic VOUT2 capacitor and 4.7 µH
inductor make up the entire external component
solution for this dual-output application. No external
dividers or compensation components are necessary.
For this application, the input-voltage range is 2.7V to
4.2V, VOUT1 = 1.5V at 500 mA, while VOUT2 = 2.5V at
300 mA.
5.3
Adjustable-Output Application
A typical VOUT1 adjustable-output application is also
shown in “Typical Application Circuits”. For this
application, the buck regulator output voltage is adjustable by using two external resistors as a voltage
divider. For adjustable-output voltages, it is recommended that the top resistor divider value be 200 kΩ.
The bottom resistor divider can be calculated using the
following formula:
EQUATION 5-1:
R BOT
V FB
= R TOP × ⎛⎝ --------------------------------⎞⎠
V OUT1 – V FB
An additional VIN2 capacitor can be added to reduce
high-frequency noise on the LDO input-voltage pin
(VIN2). This additional capacitor (1 µF) is not necessary
for typical applications.
5.4
Input and Output Capacitor
Selection
As with all buck-derived dc-dc switching regulators, the
input current is pulled from the source in pulses. This
places a burden on the TC1313 input filter capacitor. In
most applications, a minimum of 4.7 µF is
recommended on VIN1 (buck regulator input-voltage
pin). In applications that have high source impedance,
or have long leads (10 inches) connecting to the input
source, additional capacitance should be used. The
capacitor type can be electrolytic (aluminum, tantalum,
POSCAP, OSCON) or ceramic. For most portable
electronic applications, ceramic capacitors are
preferred due to their small size and low cost.
For applications that require very low noise on the LDO
output, an additional capacitor (typically 1 µF) can be
added to the VIN2 pin (LDO input voltage pin).
Low ESR electrolytic or ceramic can be used for the
buck regulator output capacitor. Again, ceramic is
recommended because of its physical attributes and
cost. For most applications, a 4.7 µF is recommended.
Refer to Table 5-1 for recommended values. Larger
capacitors (up to 22 µF) can be used. There are some
advantages in load step performance when using
larger value capacitors. Ceramic materials, X7R and
X5R, have low temperature coefficients and are well
within the acceptable ESR range required.
TABLE 5-1:
TC1313 RECOMMENDED
CAPACITOR VALUES
C (VIN1)
C (VIN2)
COUT1
COUT2
Min
4.7 µF
none
4.7 µF
1 µF
Max
none
none
22 µF
10 µF
Example:
RTOP = 200 kΩ
VOUT1 = 2.1V
VFB = 0.8V
RBOT = 200 kΩ x (0.8V/(2.1V – 0.8V))
RBOT = 123 kΩ (Standard Value = 121 kΩ)
For adjustable output applications, an additional R-C
compensation is necessary for the buck regulator
control loop stability. Recommended values are:
RCOMP = 4.99 kΩ
CCOMP = 33 pF
© 2009 Microchip Technology Inc.
DS21974B-page 19
TC1313
5.5
Inductor Selection
For most applications, a 4.7 µH inductor is
recommended to minimize noise. There are many
different magnetic core materials and package options
to select from. That decision is based on size, cost and
acceptable radiated energy levels. Toroid and shielded
ferrite pot cores will have low radiated energy but tend
to be larger and more expensive. With a typical
2.0 MHz switching frequency, the inductor ripple
current can be calculated based on the following
formulas.
EQUATION 5-2:
V OUT
DutyCycle = ------------V IN
Duty cycle represents the percentage of switch-on
time.
TABLE 5-2:
TC1313 RECOMMENDED
INDUCTOR VALUES
Part
Value
Number (µH)
DCR
MAX
Ω
IDC (A)
(max)
Size
WxLxH (mm)
Coiltronics®
SD10
2.2
0.091
1.35
5.2, 5.2, 1.0 max.
SD10
3.3
0.108
1.24
5.2, 5.2, 1.0 max.
SD10
4.7
0.154
1.04
5.2, 5.2, 1.0 max.
SD12
2.2
0.075
1.80
5.2, 5.2, 1.2 max.
SD12
3.3
0.104
1.42
5.2, 5.2, 1.2 max.
SD12
4.7
0.118
1.29
5.2, 5.2, 1.2 max.
Coiltronics
Corporation®
Sumida
CMD411
2.2
0.116
0.950 4.4, 5.8, 1.2 max.
CMD411
3.3
0.174
0.770 4.4, 5.8, 1.2 max.
CMD411
4.7
0.216
0.750 4.4, 5.8, 1.2 max.
1008PS
4.7
0.35
1.0
3.8, 3.8, 2.74 max.
1812PS
4.7
0.11
1.15
5.9, 5.0, 3.81 max.
Coilcraft®
EQUATION 5-3:
1
T ON = DutyCycle × ---------F SW
Where:
FSW
=
Switching Frequency
The inductor ac ripple current can be calculated using
the following relationship:
EQUATION 5-4:
ΔI L
V L = L × -------Δt
Where:
VL
=
voltage across the inductor
(VIN – VOUT)
Δt
=
on-time of P-channel MOSFET
5.6
5.6.1
Thermal Calculations
BUCK REGULATOR OUTPUT
(VOUT1)
The TC1313 is available in two different 10-pin
packages (MSOP and 3x3 DFN). By calculating the
power dissipation and applying the package thermal
resistance, (θJA), the junction temperature is estimated.
The maximum continuous junction temperature rating
for the TC1313 is +125°C.
Solving for ΔIL = yields:
To quickly estimate the internal power dissipation for
the switching buck regulator, an empirical calculation
using measured efficiency can be used. Given the
measured efficiency (Section 2.0 “Typical Performance Curves”), the internal power dissipation is
estimated below.
EQUATION 5-5:
EQUATION 5-6:
VL
ΔI L = ------ × Δt
L
OUT1 × I OUT1⎞
⎛V
------------------------------------– ( V OUT1 × I OUT1 ) = P Dissipation
⎝ Efficiency ⎠
When considering inductor ratings, the maximum DC
current rating of the inductor should be at least equal to
the maximum buck regulator load current (IOUT1), plus
one half of the peak-to-peak inductor ripple current (1/
2 * ΔIL). The inductor DC resistance can add to the
buck converter I2R losses. A rating of less than 200 mΩ
is recommended. Overall efficiency will be improved by
using lower DC resistance inductors.
The first term is equal to the input power (definition of
efficiency, POUT/PIN = Efficiency). The second term is
equal to the delivered power. The difference is internal
power dissipation. This estimate assumes that most of
the power lost is internal to the TC1313. There is some
percentage of power lost in the buck inductor, with very
little loss in the input and output capacitors.
DS21974B-page 20
© 2009 Microchip Technology Inc.
TC1313
For example, for a 3.6V input, 1.8V output with a load
of 400 mA, the efficiency taken from Figure 2-7 is
approximately 84%. The internal power dissipation is
approximately 137 mW.
5.6.2
LDO OUTPUT (VOUT2)
The internal power dissipation within the TC1313 LDO
is a function of input voltage, output voltage and output
current. The following equation can be used to
calculate the internal power dissipation for the LDO.
minimize trace length. The CIN1 and COUT1 capacitor
returns are connected closely together at the PGND
plane. The LDO optional input capacitor (CIN2) and
LDO output capacitor COUT2 are returned to the AGND
plane. The analog ground plane and power ground
plane are connected at one point (shown near L1). All
other signals (SHDN1, SHDN2, feedback in the
adjustable output case) should be referenced to AGND
and have the AGND plane underneath them.
- Via
AGND to PGND
EQUATION 5-7:
P LDO = ( V IN ( MAX ) – V OUT2 ( MIN ) ) × I OUT2 ( MAX )
+VOUT1
* CIN2 Optional
Where:
PLDO = LDO Pass device internal power
dissipation
VIN(MAX) = Maximum input voltage
VOUT(MIN) = LDO minimum output voltage
The maximum power dissipation capability for a
package can be calculated given the junction-toambient thermal resistance and the maximum ambient
temperature for the application. The following equation
can be used to determine the package’s maximum
internal power dissipation.
5.6.3
LDO POWER DISSIPATION
EXAMPLE
Input Voltage
VIN = 5V ±10%
COUT1
L1
AGND
PGND
CIN2
1
10
+VIN2
2
9
+VOUT2
3
8
COUT2
CIN1
+VIN1
7
4
5
6
TC1313
PGND Plane
AGND
AGND Plane
FIGURE 5-1:
Component Placement,
Fixed-Output 10-Pin MSOP.
There will be some difference in layout for the 10-pin
DFN package due to the thermal pad. A typical fixedoutput DFN layout is shown below. For the DFN layout,
the VIN1 to VIN2 connection is routed on the bottom of
the board around the TC1313 thermal pad.
LDO Output Voltage and Current
VOUT = 3.3V
IOUT = 300 mA
Internal Power Dissipation
PLDO(MAX) = (VIN(MAX) – VOUT2(MIN)) x IOUT2(MAX)
- Via
* CIN2 Optional
5.7
PCB Layout Information
Some basic design guidelines should be used when
physically placing the TC1313 on a Printed Circuit
Board (PCB). The TC1313 has two ground pins,
identified as AGND (analog ground) and PGND (power
ground). By separating grounds, it is possible to
minimize the switching frequency noise on the LDO
output. The first priority, while placing external
components on the board, is the input capacitor (CIN1).
Wiring should be short and wide; the input current for
the TC1313 can be as high as 800 mA. The next
priority would be the buck regulator output capacitor
(COUT1) and inductor (L1). All three of these
components are placed near their respective pins to
© 2009 Microchip Technology Inc.
COUT1
AGND
PLDO = (5.5V) – (0.975 x 3.3V))
x 300 mA
PLDO = 684.8 mW
+VOUT1
AGND to PGND
CIN2
1
COUT2
2
3
4
5
+VIN2
+VOUT2
AGND
L1
PGND
10
9
8
7
6
PGND
CIN1
+VIN1
TC1313
PGND Plane
AGND Plane
FIGURE 5-2:
Component Placement,
Fixed-Output 10-Pin DFN.
DS21974B-page 21
TC1313
5.8
Design Example
VOUT1 = 2.0V @ 500 mA
VOUT2 = 3.3V @ 300 mA
VIN = 5V ±10%
L = 4.7 µH
Calculate PWM mode inductor ripple current
Nominal Duty
Cycle = 2.0V/5.0V = 40%
P-channel
Switch-on time = 0.40 x 1/(2 MHz) = 200 ns
VL = (VIN-VOUT1) = 3V
ΔIL = (VL/L) x TON = 128 mA
Peak inductor current:
IL(PK) = IOUT1+1/2ΔIL = 564 mA
Switcher power loss:
Use efficiency estimate for 1.8V from Figure 2-7
Efficiency = 84%, PDISS1 = 190 mW
Resistor Divider:
RTOP = 200 kΩ
RBOT = 133 kΩ
LDO Output:
PDISS2 = (VIN(MAX) –
VOUT2(MIN)) x IOUT2(MAX)
PDISS2 = (5.5V – (0.975) x 3.3V) x 300 mA
PDISS2 = 684.8 mW
Total
Dissipation = 190 mW + 685 mW = 875 mW
Junction Temp Rise and Maximum Ambient
Operating Temperature Calculations
10-Pin MSOP (4-Layer Board with internal Planes)
RθJA = 113° C/Watt
Junction Temp.
Rise = 875 mW x 113° C/Watt = 98.9°C
Max. Ambient
Temperature = 125°C - 98.9°C
Max. Ambient
Temperature = 26.1°C
10-Pin DFN
RθJA = 41° C/Watt (4-Layer Board with
internal planes and 2 vias)
Junction Temp.
Rise = 875 mW x 41° C/Watt = 35.9°C
Max. Ambient
Temperature = 125°C - 35.9°C
Max. Ambient
Temperature = 89.1°C
This is above the +85°C max. ambient temperature.
DS21974B-page 22
© 2009 Microchip Technology Inc.
TC1313
6.0
PACKAGING INFORMATION
6.1
Package Marking Information
10-Lead MSOP
Example:
XXXXXX
YWWNNN
51H0E
527256
— 5 = TC1313
— 1 = 1.375V VOUT1
— H = 2.6V VOUT2
— 0 = Default
Second letter represents VOUT1 configuration:
10-Lead DFN
Example:
XXXX
YYWW
NNN
51H0
0527
256
Third letter represents VOUT2 configuration:
Code
VOUT1
Code
VOUT1
Code
VOUT1
Code
VOUT2
Code
VOUT2
Code
VOUT2
A
3.3V
J
2.4V
S
1.5V
A
3.3V
J
2.4V
S
1.5V
B
3.2V
K
2.3V
T
1.4V
B
3.2V
K
2.3V
T
—
C
3.1V
L
2.2V
U
1.3V
C
3.1V
L
2.2V
U
—
D
3.0V
M
2.1V
V
1.2V
D
3.0V
M
2.1V
V
—
E
2.9V
N
2.0V
W
1.1V
E
2.9V
N
2.0V
W
—
F
2.8V
O
1.9V
X
1.0V
F
2.8V
O
1.9V
X
—
G
2.7V
P
1.8V
Y
0.9V
G
2.7V
P
1.8V
Y
—
H
2.6V
Q
1.7V
Z
Adj
H
2.6V
Q
1.7V
Z
—
I
2.5V
R
1.6V
1
1.375V
I
2.5V
R
1.6V
Fourth letter represents +50 mV Increments:
Code
Code
0
Default
2
+50 mV to V2
1
+50 mV to V1
3
+50 mV to V1
and V2
Legend: XX...X
Y
YY
WW
NNN
e3
*
Note:
Customer-specific information
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code
Pb-free JEDEC designator for Matte Tin (Sn)
This package is Pb-free. The Pb-free JEDEC designator ( e3 )
can be found on the outer packaging for this package.
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
© 2009 Microchip Technology Inc.
DS21974B-page 23
TC1313
%
!"#$
2
%&
%!%*") ' %
*$%
%"%
%%133)))&
&3*
D
e
b
N
N
L
K
E
E2
EXPOSED
PAD
NOTE 1
1
2
2
1
NOTE 1
D2
BOTTOM VIEW
TOP VIEW
A
A1
A3
NOTE 2
4%
& 5&%
6!&(
$
55,,
6
6
67
8
%
79%
:
./0
%"
$$
.
0
%%*
+
,2
75%
,#
""5%
7;"%
,
,#
"";"%
,
.:
.
(
:
.
+
0
%%5%
5
+
.
0
%%%
,#
""
<
=
=
0
%%;"%
+/0
+.
:
+/0
%
!"#$%!&'(!%&! %(
%")%%%"
*&
&
#
"%( %" + * ) !%"
& "%
,-.
/01 / & %#%! ))%
!%%
,21 $& '! !)%
!%%
'$
$
&%
!
) 0>+/
DS21974B-page 24
© 2009 Microchip Technology Inc.
TC1313
&' ()
*#'(
$
%
2
%&
%!%*") ' %
*$%
%"%
%%133)))&
&3*
D
N
E
E1
NOTE 1
1
2
b
e
A
A2
c
φ
L
A1
L1
4%
& 5&%
6!&(
$
55,,
6
6
67
8
%
79%
=
./0
=
""**
.
:.
.
%"
$$
=
.
7;"%
,
""*;"%
,
+/0
75%
+/0
2
%5%
5
2
%%
5
/0
>
:
.,2
2
%
I
?
=
:?
5"*
:
=
+
5";"%
(
.
=
++
%
!"#$%!&'(!%&! %(
%")%%%"
& ","
%!"&
"$ %! "$ %! %#".&& "
+ & "%
,-.
/01 / & %#%! ))%
!%%
,21 $& '! !)%
!%%
'$
$
&%
!
) 0/
© 2009 Microchip Technology Inc.
DS21974B-page 25
TC1313
NOTES:
DS21974B-page 26
© 2009 Microchip Technology Inc.
TC1313
APPENDIX A:
REVISION HISTORY
Revision B (January 2009)
The following is the list of modifications:
1.
Added the new DFN package information.
Revision A (November 2005)
• Original Release of this Document.
© 2009 Microchip Technology Inc.
DS21974B-page 23
TC1313
NOTES:
DS21974B-page 24
© 2009 Microchip Technology Inc.
TC1313
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
TC1313
X
X
X
VOUT1 VOUT2
Device:
Options
TC1313:
X
XX
+50 mV
Temp Package
Increments Range
XX
Tube
or
Tape &
Reel
PWM/LDO combo.
Code
VOUT1
Code
VOUT2
Code
+50 mV
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
1
3.3V
3.2V
3.1V
3.0V
2.9V
2.8V
2.7V
2.6V
2.5V
2.4V
2.3V
2.2V
2.1V
2.0V
1.9V
1.8V
1.7V
1.6V
1.5V
1.4V
1.3V
1.2V
1.1V
1.0V
0.9V
Adjustable
1.375V
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
1
3.3V
3.2V
3.1V
3.0V
2.9V
2.8V
2.7V
2.6V
2.5V
2.4V
2.3V
2.2V
2.1V
2.0V
1.9V
1.8V
1.7V
1.6V
1.5V
0
1
2
3
Default
V1 + 50 mV
V2 + 50 mV
V1 and V2
+ 50 mV
Examples:
a)
TC1313-1H0EMF:
b)
TC1313-1H0EUN:
c)
TC1313-1P0EMF:
d)
TC1313-1P0EUN:
e)
TC1313-DG0EMF:
f)
TC1313-RD1EMF:
g)
TC1313-ZS0EUN:
h)
TC1313-1H0EMFTR:
i)
TC1313-1H0EUNTR:
j)
TC1313-1P0EMFTR:
k)
TC1313-1P0EUNTR:
l)
TC1313-DG0EMFTR:
m)
TC1313-RD1EMFTR:
n)
TC1313-ZS0EUNTR:
1.375V, 2.6V, Default,
10LD DFN pkg.
1.375V, 2.6V, Default,
10LD MSOP pkg.
1.375V, 1.8V, Default,
10LD DFN pkg.
1.375V, 1.8V, Default,
10LD MSOP pkg.
3.0V, 2.7V, Default,
10LD DFN pkg.
1.65V, 3.0V,
10LD DFN pkg.
Adj., 1.5V, Default,
10LD MSOP pkg.
1.375V, 2.6V, Default,
10LD DFN pkg
Tape and Reel.
1.375V, 2.6V, Default,
10LD MSOP pkg
Tape and Reel.
1.375V, 1.8V, Default,
10LD DFN pkg
Tape and Reel.
1.375V, 1.8V, Default,
10LD MSOP pkg
Tape and Reel.
3.0V, 2.7V, Default,
10LD DFN pkg
Tape and Reel.
1.65V, 3.0V,
10LD DFN pkg
Tape and Reel.
Adj., 1.5V, Default,
10LD MSOP pkg
Tape and Reel.
* Contact Factory for Alternate Output Voltage and Reset
Voltage Configurations.
Temperature
Range:
E
= -40°C to +85°C
Package:
MF
UN
= Dual Flat, No Lead (3x3 mm body), 10-lead
= Plastic Micro Small Outline (MSOP), 10-lead
Tube or
Tape and Reel:
Blank
TR
= Tube
= Tape and Reel
© 2009 Microchip Technology Inc.
DS21974B-page 25
TC1313
NOTES:
DS21974B-page 26
© 2009 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, rfPIC, SmartShunt and UNI/O are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
FilterLab, Linear Active Thermistor, MXDEV, MXLAB,
SEEVAL, SmartSensor and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, In-Circuit Serial
Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM,
PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo,
PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total
Endurance, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2009, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
© 2009 Microchip Technology Inc.
DS21974B-page 27
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-4182-8400
Fax: 91-80-4182-8422
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-238813S0
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
01/02/08
DS21974B-page 28
© 2009 Microchip Technology Inc.