DATASHEET | DECEMBER 27, 2007 5016-Series Fiber-Transceiver Applications Radar testing/calibration Signal processing The 5016-Series transceiver line delivers unmatched performance for radar testing, signal processing, phased antenna array, and phase noise testing when used in conjunction with the 355A Fiber-optic Delay Line and when used as a standalone product it serves as a high dynamic range transceiver for Microwave applications. These rugged devices eliminate many of the problems that are inherent in alternative delay line technologies including acoustic wave devices and coaxial delay lines. Cellular and PCS networks Ortel’s fiber-optic transceivers provide bandwidth that is essentially independent of fiber length, loss or delay, and triple transit signals that are immeasurable. In addition to enhanced electrical performance, the delay lines provide several mechanical advantages. Ortel’s technology takes advantage of the rigid yet flexible properties of fiber-optic cable to provide repeatable enhanced phase and group delay characteristics. Military triband communications The small size of these components allows for a long delay in a compact package with the superior temperature stability of fiber. Phased antenna array Phase noise testing Antenna remoting Tracking Telemetry & Control TT&C Features Bandwidth to 18 GHz Performance Highlights Min Wavelength Options Typical 1290 Max Units 1340 nm High dynamic range Built-in optical isolator 1310 nm Temperature Range -25 - +65 °C Frequency Range 0.1 - 10 - 18 GHz See following pages for complete specifications and conditions. For more information on this and other products: Contact Sales at Emcore 626-430-4000, or visit www.emcore.com. 5016-Series Fiber-Transceiver DATA SHEET| | DECEMBER 27, 2007 Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operational sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Symbol Condition Min Max Units Operating Temperature Range of Baseplate: TOP continuous -40 +65 °C Storage Temperature TSTG - -55 +85 °C PIN 60 seconds - 20 dBm - HBM: R = 1500 Ohm, C = 100 pF -500 500 V RF Input Power ESD, module dc Interface Characteristics Pin Number Min Typ Max Max Ripple Current 1 14V 15V 16V 100 mV p-p 0.3 A max 2 4.5V 5V 5.5V 200 mV p-p 1.6 A max Front Panel LEDs Pin/Package Information Power on Nine-Pin D-sub Connector dc Monitor Voltages Pin Description 1 +15 Vdc 2 +5 Vdc o 1V/100mA ±2% accuracy (into 1 MΩ load). Proportional to laser optical power 3 NC Photodiode current, pin7 4 Power Ground 5 Reference Ground o 1V/mA ±2% accuracy (into 1 MΩ load). Proportional to photodiode input power 6 Laser Photodiode Current Monitor Laser dc current, pin 8: 7 Received Optical Power 8 Laser Current Monitor o 1V/100mA ±2% accuracy (into 1 MΩ load). Alarm Circuits 9 Laser Over-temperature Alarm Laser Photodiode current, pin6 Alarm Circuits 1 The alarms are open-collector outputs capable of sinking 20 mA to ground when active and withstanding 15V when off. 1: Open collector outputs Ordering Information Laser temperature, pin 9 o Option Connector/Pigtail -020 FC/APC Bulkhead Optical Connector -022 FC/APC Optical Connector/ 3mm Fiber Pigtail Sinks current when laser internal temperature exceeds + 2 °C of set-point (nominally 25°C). For more information on this and other products: Contact Sales at Emcore 626-293-3400, or visit www.emcore.com. 5016-Series Fiber-Transceiver DATA SHEET| | DECEMBER 27, 2007 Electrical/Optical Characteristics Optical Parameter Specifications Unit Single mode (9/125) µm FC/APC - 5016A,B,C only 8 (+9) mW (dBm), min 5016D only 2 (+3) mW (dBm), max 5016A,B,C,D used with 355A delay spool 5 (+7) mW (dBm), max 2 (+3) mW (dBm), max 15 (+12) mW (dBm), max Fiber Optical Connectors Optical Transmitter Output Power Optical Receiver Input Power Low Power System, 5016D High Power System, 5016A,B,C RF Characteristics Parameter 5016A 5016B RF Connectors 5016C 5016D SMA Unit - Upper Band Edge Frequency 4 10 15 18 GHz Lower Band Edge Frequency 0.1 0.1 0.1 0.1 GHz 34 dB Insertion Loss (0 dB Optical) Amplitude Flatness Input / Output RF Return Loss 28 ± 1.5 ± 2.0 ± 2.5 ± 3.0 dB 9.5 9.5 6 6 dB Impedance 50 Ω Input 1 dB Compression +20 dBm Input Third Order Intercept 0.01 GHz – 2.5 GHz 35 - - - dBm 2.5 GHz – 6.0 GHz 30 - - - dBm 6.0 GHz – 10.0 GHz - 25 25 25 dBm 10.0 GHz – 18.0 GHz - - - 20 dBm 0.01 GHz – 10.0 GHz 46 46 46 46 dB 10.0 GHz – 15.0 GHz 51 51 51 51 dB 15.0 GHz – 18.0 GHz 57 57 57 57 dB Noise Figure 3 of 5 5016-Series Fiber-Transceiver DATA SHEET| | DECEMBER 27, 2007 Outline Diagram Dimensions are in inches. 6.750” 0.125 0.190” 6.000” 5.500 ” 0.250 ” 6.375” POWER ON RF IN LASER PHOTODIODE RF OUT 2.380” DB 9 M 4 of 5 5016-Series Fiber-Transceiver DATA SHEET| | DECEMBER 27, 2007 Laser Safety Class IIIb Laser Product FDA/CDRH Class IIIb laser product. All versions are Class IIIb laser products per CDHR 1040 Laser Safety Requirements. All versions are class 3B laser products per IEC 60825-1:1993. The device has been classified with the FDA under accession number 220191. This product complies with 21 CFR 1040.10 and 1040.11. Single-mode fiber pigtail Wavelength = 1.3 µm Maximum power = 30 mW Because of size constraints, laser safety labeling (including an FDA class IIIb label) is not affixed to the module but attached to the outside of the shipping carton. Product is not shipped with power supply. Caution: Use of controls, adjustments and procedures other than those specified herein may result in hazardous laser radiation exposure. DANGER DANGER INVI SIBLE LASER RADI ATION IS EMITTED FROM THE END O F FIBER OR CONNECTO R Avoid di rect exposure to beam INVISIBLE LASERRADIATION AVOIDDIRECT EXPOSURE TO BEAM Do not view beam directly wi th optical instr uments Wavelength: 1.3 µm Max. Output: 50 mW, Class IIIb Laser Product INVISIBLE LASER RADIATION EMITTED FROM END OF FIBER OR CONNECTOR Avoidexposure to beam Class 3BLaser Product IEC-60825 1993 Max. Output: 50 mW Wavelength: 1.3 µm Information contained herein is deemed to be reliable and accurate as of issue date. EMCORE reserves the right to change the design or specifications of the product at any time without notice. Ortel, the Ortel logo, EMCORE, and the EMCORE logo are trademarks of EMCORE Corporation. Ortel, a division of EMCORE DS. Fiber Transceiver 2015 West Chestnut Street Alhambra, California 91803-1542 Tel: 626-293-3400 Fax: 626-293-3423 www.emcore.com 5 of 5 Copyright 2007. EMCORE Corporation