Internationally Approved Toggles Series P Distinctive Characteristics International certifications from UL, CSA, VDE, SEMKO, and SEV. High torque bushing construction prevents rotation or separation from frame during installation. Stainless steel frame resists corrosion and increases environmental safety. Case/base of heat resistant resin meets UL94V-0 flammability standard. Contacts of special silver alloy resist arcing and guarantee stable electrical contact and long life. High insulating barriers increase isolation of circuits in double pole devices and provide added protection to contact points. Prominent external insulating barriers increase insulation resistance and dielectric strength. Epoxy sealed terminals prevent entry of flux, solvents, and other contaminants. Clinching of the frame to the case well above the base and terminals provides 4,000V dielectric strength. Actual Size NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Internationally Approved Toggles Series P General Specifications Electrical Capacity Resistive Load: Motor Load: Lamp Load: Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Angle of Throw: Materials & Finishes Toggle Cap: Lever: Bushing: Frame: Case/Base: Movable Contacts: Stationary Contacts: Terminals: Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Installation Soldering Time & Temp: Standards & Certifications Flammability Standards: UL Recognized: C-UL Recognized: R CSA Certified: V D E VDE Approved: SEMKO Approved: SEV Approved: 10A @ 125V AC or 6A @ 250V AC 400W @ 125V AC 2A @ 125V AC for On-Off-On circuit & 3A @ 125V AC for other circuits 10 milliohms maximum 1,000 megohms minimum @ 500V DC 2,000V AC minimum between contacts for 1 minute minimum; 4,000V AC minimum between contacts & case for 1 minute minimum 100,000 operations minimum 25,000 operations minimum 25° Brass with nickel plating Brass with chrome plating Brass with nickel plating Stainless steel Diallyl phthalate resin (UL94V-0) Silver alloy with silver plating Pure silver with silver plating Copper with silver plating –10°C through +85°C (+14°F through +185°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering Recommended (Straight PC): See Profile A in Supplement section. Manual Soldering: See Profile A in Supplement section. UL94V-0 rated case/base All models recognized at 10A @ 125V AC & 6A @ 250V AC; UL File No. WOYR2.E44145. Add “/U” to end of part number to order UL mark on switch. All models recognized at 10A @ 125V AC & 6A @ 250V AC; C-UL File No. WOYR8.E44145. Add “/C-UL” to end of part number to order C-UL mark on switch. All models certified at 10A @ 125V AC & 6A @ 250V AC; CSA File No. 023535-0-000. Add “/C” to end of part number to order CSA mark on switch. All models approved at 10A @ 125V AC & 6A @ 250V AC; License No. 119174. Marking on switch is standard. P2011, P2012, P2013, P2021, P2022 models approved at 10A @ 125V AC & 6A @ 125/250V AC; Reference No. 9915205/01-02. Marking on switch is standard. All models with Quick Connect Terminals approved at 10A @ 125V AC & 6A @ 125/250V AC; (P2013 for micro-switch only); Authorization No. 02.0466. Marking on switch is standard. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07 Series P Internationally Approved Toggles TYPICAL SWITCH ORDERING EXAMPLE P20 22 POLES & CIRCUITS B TOGGLES & BUSHINGS 11 SPST ON NONE OFF 12 SPDT ON NONE ON 13 SPDT ON OFF ON 21 DPST ON NONE OFF 22 DPDT ON NONE ON 23 DPDT ON OFF ON No Code TERMINALS .512” (13.0mm) White Cap with 6mm Bushing E .450” (11.4mm) Flatted with 6mm Bushing B .689” (17.5mm) Large Bat with 12mm Bushing D .748” (19.0mm) White Capped Column with 12mm Bushing No Code Solder Lug P Straight PC Z .187” (4.75mm) Quick Connect DESCRIPTION FOR TYPICAL ORDERING EXAMPLE P2022B .689” (17.5mm) Large Bat with 12mm Bushing IMPORTANT: VDE, SEMKO & SEV are marked on approved models. Switches are supplied without UL, C-UL & CSA marking unless specified. Specific models & ratings noted on General Specifications page. DPDT ON-NONE-ON Circuit Solder Lug Terminals POLES & CIRCUITS Toggle Position Down Center Connected Terminals Up Down Throw & Schematics Center Up Note: Terminal numbers are on the switch. Pole Model SP P2011 ON NONE OFF 1-1b OPEN OPEN SPST SP P2012 P2013 ON ON NONE OFF ON ON 1-1b OPEN 1-1a SPDT DP P2021 ON NONE OFF 1-1b 2-2b OPEN OPEN DPST DP P2022 P2023 ON ON NONE OFF ON ON 1-1b 2-2b OPEN 1-1a 2-2a DPDT Keyway Keyway 1 (COM) 1b 1 (COM) 1a 1 1b (COM) 2 1b 1 1a 2b (COM) 1b 2 2a NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 2b 03-07 Internationally Approved Toggles Series P TOGGLES & BUSHINGS No Code .512” (13.0mm) White Cap with 6mm Bushing .450” (11.4mm) Flatted with 6mm Bushing E .689” (17.5mm) Large Bat with 12mm Bushing B .748” (19.0mm) White Capped Column with 12mm Bushing D 25° 25° (4.2) Dia .165 (2.54) .100 (13.0) .512 25° (19.0) .748 (17.5) .689 (11.4) .450 Panel Cutouts Panel Thickness with Keyway .134” (3.4mm) maximum Panel Thickness with Locking Ring .102” (2.6mm) maximum (5.6) .220 (6.35) Dia .250 (0.6) .024 (6.35) Dia .250 (12.5) Dia .492 Panel Thickness with Keyway .256” (6.5mm) maximum (6.5) .256 (2.2) Dia .087 25° (4.4) Dia .173 (6.0) Dia .236 (5.08) .200 Panel Thickness with Locking Ring .217” (5.5mm) maximum (11.5) .453 (1.5) .060 (12.5) Dia .492 (9.0) .354 (3.0) Dia .118 Standard Hardware For 6mm Bushing: 1 Locking Ring AT507M, 1 Internal Tooth Lockwasher AT509, 2 Hex Nuts AT513M For 12mm Bushing: 1 Hex Face Nut AT503M, 1 Locking Ring AT506M, 1 Internal Tooth Lockwasher AT508, 1 Hex Mounting Nut AT527M TERMINALS No Code P Epoxy Seal Epoxy Seal Straight PC (4.8) .189 (2.6) .102 (7.6) .299 SPST 1 2b 1b (7.62) Typ .300 (6.35) .250 (1.3) Dia .051 1b (1.17) .046 Thk = (1.0) .039 .187” (4.75mm) Quick Connect Z (2.0) (4.5) .079 .177 (1.25) .049 Thk = (1.0) .039 Solder Lug SPDT 1 (1.8) Dia Typ .071 (7.62) Typ .300 DPST (7.62) Typ .300 1 DPDT (1.8) Dia Typ .071 (10.16) .400 (1.8) Dia Typ .071 (4.75) .187 Thk = (0.8) .031 1b 2 1a (9.0) .354 2b 1b 2 1 2a (7.62) Typ .300 1a (1.8) Dia Typ .071 (10.16) .400 TYPICAL SWITCH DIMENSIONS 6mm Bushing P2011, P2012, P2013 (1.0) Typ .039 (1.25) x (2.0) Typ .049 x .079 Keyway M6 P0.75 1b (0.8) .031 25° (4.2) Dia .165 (13.0) .512 (11.0) .433 P2012 (0.9) .035 (8.0) .315 (22.0) .866 (5.0) .197 (20.5) .807 1 (7.62) .300 1a (0.5) .020 (2.6) .102 P2011 models do not have terminal 1a. 12mm Bushing P2021B, P2022B, P2023B Keyway (1.0) Typ .039 (1.25) x (2.0) Typ .049 x .079 M12 P1 2b 25° (20.0) .787 P2022B (6.0) Dia .236 1b (0.8) .031 (7.62) .300 (17.5) .689 (12.0) .472 (21.1) .831 (5.0) .197 (0.5) .020 2 1 2a (20.5) .807 1a (10.16) .400 (2.6) Typ .102 P2021 models do not have terminals 1a & 2a. NKK Switches • email: [email protected] • Phone (480) 991-0942 • Fax (480) 998-1435 • www.nkkswitches.com 03-07