MICROCHIP 93LC56C

93AA56A/B/C, 93LC56A/B/C,
93C56A/B/C
2K Microwire Compatible Serial EEPROM
Device Selection Table
VCC Range
ORG Pin
Word Size
Temp Ranges
93AA56A
1.8-5.5
No
8-bit
I
P, SN, ST, MS, OT, MC
93AA56B
1.8-5-5
No
16-bit
I
P, SN, ST, MS, OT, MC
93LC56A
2.5-5.5
No
8-bit
I, E
P, SN, ST, MS, OT, MC
93LC56B
2.5-5.5
No
16-bit
I, E
P, SN, ST, MS, OT, MC
93C56A
4.5-5.5
No
8-bit
I, E
P, SN, ST, MS, OT, MC
93C56B
4.5-5.5
No
16-bit
I, E
P, SN, ST, MS, OT, MC
93AA56C
1.8-5.5
Yes
8- or 16-bit
I
P, SN, ST, MS, MC
Part Number
Packages
93LC56C
2.5-5.5
Yes
8- or 16-bit
I, E
P, SN, ST, MS, MC
93C56C
4.5-5.5
Yes
8- or 16-bit
I, E
P, SN, ST, MS, MC
Pin Function Table
Features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Low-Power CMOS Technology
ORG Pin to Select Word Size for ‘56C’ Version
256 x 8-bit Organization ‘A’ Version (no ORG)
128 x 16-bit Organization ‘B’ Version (no ORG)
Self-Timed Erase/Write Cycles (including
Auto-Erase)
Automatic Erase All (ERAL) before Write All
(WRAL)
Power-On/Off Data Protection Circuitry
Industry Standard 3-Wire Serial I/O
Device Status Signal (Ready/Busy)
Sequential Read Function
1,000,000 Erase/write Cycles
Data Retention > 200 Years
Pb-free and RoHS Compliant
Temperature Ranges Supported:
- Industrial (I)
-40°C to +85°C
- Automotive (E) -40°C to +125°C
© 2008 Microchip Technology Inc.
Name
Function
CS
Chip Select
CLK
Serial Data Clock
DI
Serial Data Input
DO
Serial Data Output
VSS
Ground
NC
No internal connection
ORG
Memory Configuration
VCC
Power Supply
Description:
The Microchip Technology Inc. 93XX56A/B/C devices
are 2Kbit low-voltage serial Electrically Erasable
PROMs (EEPROM). Word-selectable devices such as
the 93AA56C, 93LC56C or 93C56C are dependent
upon external logic levels driving the ORG pin to set
word size. For dedicated 8-bit communication, the
93XX56A devices are available, while the 93XX56B
devices provide dedicated 16-bit communication.
Advanced CMOS technology makes these devices
ideal for low-power, nonvolatile memory applications.
The entire 93XX Series is available in standard
packages including 8-lead PDIP and SOIC, and
advanced packaging including 8-lead MSOP, 6-lead
SOT-23, 8-lead 2x3 DFN and 8-lead TSSOP. All
packages are Pb-free (Matte Tin) finish.
DS21794F-page 1
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
Package Types (not to scale)
ROTATED SOIC
(ex: 93LC46BX)
NC
VCC
CS
CLK
1
2
3
4
PDIP/SOIC
(P, SN)
8 ORG*
7 VSS
6 DO
5 DI
CS
CLK
DI
DO
TSSOP/MSOP
(ST, MS)
CS
CLK
DI
DO
1
2
3
4
8
7
6
5
1
2
3
4
8
7
6
5
VCC
NC
ORG*
VSS
SOT-23
(OT)
VCC
NC
ORG*
VSS
DO
VSS
1
6
VCC
2
5
CS
DI
3
4
CLK
DFN
(MC)
CS
CLK
DI
DO
1
2
3
4
8
7
6
5
VCC
NC
ORG*
VSS
*ORG pin is NC on A/B devices.
DS21794F-page 2
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
1.0
ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings(†)
VCC.............................................................................................................................................................................7.0V
All inputs and outputs w.r.t. VSS ..........................................................................................................-0.6V to VCC +1.0V
Storage temperature ............................................................................................................................... -65°C to +150°C
Ambient temperature with power applied................................................................................................ -40°C to +125°C
ESD protection on all pins ......................................................................................................................................................≥ 4 kV
†NOTICE: Stresses above those listed under “Absolute Maximum Ratings” may cause permanent damage to the
device. This is a stress rating only and functional operation of the device at those or any other conditions above those
indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for
extended periods may affect device reliability.
TABLE 1-1:
DC CHARACTERISTICS
All parameters apply over the specified
ranges unless otherwise noted.
Param.
Symbol
No.
Parameter
Industrial (I):
TA = -40°C to +85°C, VCC = +1.8V to +5.5V
Automotive (E): TA = -40°C to +125°C, VCC = +2.5V to +5.5V
Min
Typ
Max
Units
Conditions
D1
VIH1
VIH2
High-level input voltage
2.0
0.7 VCC
—
—
VCC +1
VCC +1
V
V
VCC ≥ 2.7V
VCC < 2.7V
D2
VIL1
VIL2
Low-level input voltage
-0.3
-0.3
—
—
0.8
0.2 VCC
V
V
VCC ≥ 2.7V
VCC < 2.7V
D3
Vol1
Vol2
Low-level output voltage
—
—
—
—
0.4
0.2
V
V
IOL = 2.1 mA, VCC = 4.5V
IOL = 100 μA, VCC = 2.5V
D4
VOH1
VOH2
High-level output voltage
2.4
VCC - 0.2
—
—
—
—
V
V
IOH = -400 μA, VCC = 4.5V
IOH = -100 μA, VCC = 2.5V
D5
ILI
Input leakage current
—
—
±1
μA
VIN = VSS or VCC
D6
ILO
Output leakage current
—
—
±1
μA
VOUT = VSS or VCC
D7
CIN,
COUT
Pin capacitance (all inputs/
outputs)
—
—
7
pF
VIN/VOUT = 0V (Note 1)
TA = 25°C, FCLK = 1 MHz
D8
ICC write Write current
—
—
—
500
2
—
mA
μA
FCLK = 3 MHz, Vcc = 5.5V
FCLK = 2 MHz, Vcc = 2.5V
D9
ICC read Read current
—
—
—
—
—
100
1
500
—
mA
μA
μA
FCLK = 3 MHz, VCC = 5.5V
FCLK = 2 MHz, VCC = 3.0V
FCLK = 2 MHz, VCC = 2.5V
D10
ICCS
Standby current
—
—
—
—
1
5
μA
μA
I – Temp
E – Temp
CLK = CS = 0V
ORG = DI = VSS or VCC
(Note 2) (Note 3)
D11
VPOR
VCC voltage detect
—
1.5
—
V
—
3.8
—
V
93AA56A/B/C, 93LC56A/B/C
(Note 1)
93C56A/B/C
Note 1:
2:
3:
This parameter is periodically sampled and not 100% tested.
ORG pin not available on ‘A’ or ‘B’ versions.
Ready/Busy status must be cleared from DO; see Section 3.4 "Data Out (DO)".
© 2008 Microchip Technology Inc.
DS21794F-page 3
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
TABLE 1-2:
AC CHARACTERISTICS
All parameters apply over the specified
ranges unless otherwise noted.
Param.
Symbol
No.
Parameter
Industrial (I):
TA = -40°C to +85°C, VCC = +1.8V TO +5.5V
Automotive (E): TA = -40°C to +125°C, VCC = +2.5V TO +5.5V
Min
Max
Units
Conditions
A1
FCLK
Clock frequency
—
3
2
1
MHz
MHz
MHz
4.5V ≤ VCC < 5.5V, 93XX56C only
2.5V ≤ VCC < 5.5V
1.8V ≤ VCC < 2.5V
A2
TCKH
Clock high time
200
250
450
—
ns
ns
ns
4.5V ≤ VCC < 5.5V, 93XX56C only
2.5V ≤ VCC < 5.5V
1.8V ≤ VCC < 2.5V
A3
TCKL
Clock low time
100
200
450
—
ns
ns
ns
4.5V ≤ VCC < 5.5V, 93XX56C only
2.5V ≤ VCC < 5.5V
1.8V ≤ VCC < 2.5V
A4
TCSS
Chip Select setup time
50
100
250
—
ns
ns
ns
4.5V ≤ VCC < 5.5V
2.5V ≤ VCC < 4.5V
1.8V ≤ VCC < 2.5V
A5
TCSH
Chip Select hold time
0
—
ns
1.8V ≤ VCC < 5.5V
A6
TCSL
Chip Select low time
250
—
ns
1.8V ≤ VCC < 5.5V
A7
TDIS
Data input setup time
50
100
250
—
ns
ns
ns
4.5V ≤ VCC < 5.5V, 93XX56C only
2.5V ≤ VCC < 5.5V
1.8V ≤ VCC < 2.5V
A8
TDIH
Data input hold time
50
100
250
—
ns
ns
ns
4.5V ≤ VCC < 5.5V, 93XX56C only
2.5V ≤ VCC < 5.5V
1.8V ≤ VCC < 2.5V
A9
TPD
Data output delay time
—
200
250
400
ns
ns
ns
4.5V ≤ VCC < 5.5V, CL = 100 pF
2.5V ≤ VCC < 4.5V, CL = 100 pF
1.8V ≤ VCC < 2.5V, CL = 100 pF
A10
TCZ
Data output disable time
—
100
200
ns
ns
4.5V ≤ VCC < 5.5V, (Note 1)
1.8V ≤ VCC < 4.5V, (Note 1)
A11
TSV
Status valid time
—
200
300
500
ns
ns
ns
4.5V ≤ VCC < 5.5V, CL = 100 pF
2.5V ≤ VCC < 4.5V, CL = 100 pF
1.8V ≤ VCC < 2.5V, CL = 100 pF
A12
TWC
Program cycle time
—
6
ms
Erase/Write mode (AA and LC
versions)
A13
TWC
—
2
ms
Erase/Write mode
(93C versions)
A14
TEC
—
6
ms
ERAL mode, 4.5V ≤ VCC ≤ 5.5V
A15
TWL
—
15
ms
WRAL mode, 4.5V ≤ VCC ≤ 5.5V
A16
—
1M
—
Note 1:
2:
Endurance
cycles 25°C, VCC = 5.0V, (Note 2)
This parameter is periodically sampled and not 100% tested.
This application is not tested but ensured by characterization. For endurance estimates in a specific
application, please consult the Total Endurance™ Model, which may be obtained from Microchip’s web
site at www.microchip.com.
DS21794F-page 4
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
FIGURE 1-1:
CS
SYNCHRONOUS DATA TIMING
VIH
TCSS
VIL
TCKH
TCKL
TCSH
VIH
CLK
VIL
TDIS
TDIH
VIH
DI
VIL
TPD
TPD
DO
(Read)
DO
(Program)
Note:
TCZ
VOH
VOL
TCZ
TSV
VOH
Status Valid
VOL
TSV is relative to CS.
TABLE 1-3: INSTRUCTION SET FOR X16 ORGANIZATION (93XX56B OR 93XX56C WITH ORG = 1)
Instruction
SB
Opcode
Address
Data In
Data Out
Req. CLK Cycles
ERASE
1
11
X
—
(RDY/BSY)
11
ERAL
1
00
1
0
X
X
X
X
X
EWDS
1
00
0
0
X
X
X
X
X
X
—
(RDY/BSY)
11
X
—
High-Z
11
EWEN
1
00
1
1
X
X
X
X
X
X
—
High-Z
11
READ
1
10
X
A6 A5 A4 A3 A2 A1 A0
—
D15 – D0
27
WRITE
1
01
X
A6 A5 A4 A3 A2 A1 A0
D15 – D0
(RDY/BSY)
27
WRAL
1
00
0
D15 – D0
(RDY/BSY)
27
A6 A5 A4 A3 A2 A1 A0
1
X
X
X
X
X
X
TABLE 1-4: INSTRUCTION SET FOR X8 ORGANIZATION (93XX56A OR 93XX56C WITH ORG = 0)
SB
Opcode
Address
Data In
Data Out
Req. CLK
Cycles
ERASE
1
11
X A7 A6 A5 A4 A3 A2 A1 A0
—
(RDY/BSY)
12
ERAL
1
00
1
0
X
X
X
X
X
X
X
—
(RDY/BSY)
12
EWDS
1
00
0
0
X
X
X
X
X
X
X
—
High-Z
12
EWEN
1
00
1
1
X
X
X
X
X
X
X
—
High-Z
12
READ
1
10
X A7 A6 A5 A4 A3 A2 A1 A0
—
D7 – D0
20
WRITE
1
01
X A7 A6 A5 A4 A3 A2 A1 A0
D7 – D0
(RDY/BSY)
20
WRAL
1
00
0
D7 – D0
(RDY/BSY)
20
Instruction
© 2008 Microchip Technology Inc.
1
X
X
X
X
X
X
X
DS21794F-page 5
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
2.0
FUNCTIONAL DESCRIPTION
When the ORG pin (93XX56C) pin is connected to
VCC, the (x16) organization is selected. When it is
connected to ground, the (x8) organization is selected.
Instructions, addresses and write data are clocked into
the DI pin on the rising edge of the clock (CLK). The DO
pin is normally held in a High-Z state except when reading data from the device, or when checking the Ready/
Busy status during a programming operation. The
Ready/Busy status can be verified during an Erase/
Write operation by polling the DO pin; DO low indicates
that programming is still in progress, while DO high
indicates the device is ready. DO will enter the High-Z
state on the falling edge of CS.
2.1
START Condition
The Start bit is detected by the device if CS and DI are
both high with respect to the positive edge of CLK for
the first time.
2.3
Data Protection
All modes of operation are inhibited when VCC is below
a typical voltage of 1.5V for ‘93AA’ and ‘93LC’ devices
or 3.8V for ‘93C’ devices.
The EWEN and EWDS commands give additional
protection against accidentally programming during
normal operation.
Note:
For added protection, an EWDS command
should be performed after every write
operation and an external 10 kΩ pull-down
protection resistor should be added to the
CS pin.
After power-up, the device is automatically in the
EWDS mode. Therefore, an EWEN instruction must be
performed before the initial ERASE or WRITE instruction
can be executed.
Block Diagram
VCC
Before a Start condition is detected, CS, CLK and DI
may change in any combination (except to that of a
Start condition), without resulting in any device
operation (Read, Write, Erase, EWEN, EWDS, ERAL
or WRAL). As soon as CS is high, the device is no
longer in Standby mode.
VSS
Memory
Array
Address
Counter
An instruction following a Start condition will only be
executed if the required opcode, address and data bits
for any particular instruction are clocked in.
Data Register
Note:
2.2
When preparing to transmit an instruction,
either the CLK or DI signal levels must be
at a logic low as CS is toggled active high.
Data In/Data Out (DI/DO)
It is possible to connect the Data In and Data Out pins
together. However, with this configuration it is possible
for a “bus conflict” to occur during the “dummy zero”
that precedes the read operation if A0 is a logic high
level. Under such a condition the voltage level seen at
Data Out is undefined and will depend upon the relative
impedances of Data Out and the signal source driving
A0. The higher the current sourcing capability of A0,
the higher the voltage at the Data Out pin. In order to
limit this current, a resistor should be connected
between DI and DO.
DS21794F-page 6
Address
Decoder
Output
Buffer
DO
DI
ORG*
CS
CLK
Mode
Decode
Logic
Clock
Register
*ORG input is not available on A/B devices
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
2.4
Erase
The DO pin indicates the Ready/Busy status of the
device if CS is brought high after a minimum of 250 ns
low (TCSL). DO at logical ‘0’ indicates that programming
is still in progress. DO at logical ‘1’ indicates that the
register at the specified address has been erased and
the device is ready for another instruction.
The ERASE instruction forces all data bits of the specified address to the logical ‘1’ state. CS is brought low
following the loading of the last address bit. This falling
edge of the CS pin initiates the self-timed programming cycle, except on ‘93C’ devices where the rising
edge of CLK before the last address bit initiates the
write cycle.
FIGURE 2-1:
Note:
After the Erase cycle is complete, issuing
a Start bit and then taking CS low will clear
the Ready/Busy status from DO.
ERASE TIMING FOR 93AA AND 93LC DEVICES
TCSL
CS
Check Status
CLK
1
DI
1
1
AN
AN-1 AN-2
•••
A0
TCZ
TSV
DO
High-Z
Busy
Ready
High-Z
TWC
FIGURE 2-2:
ERASE TIMING FOR 93C DEVICES
TCSL
CS
Check Status
CLK
1
DI
1
1
AN
AN-1 AN-2
•••
A0
TCZ
TSV
DO
High-Z
Busy
Ready
High-Z
TWC
© 2008 Microchip Technology Inc.
DS21794F-page 7
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
2.5
Erase All (ERAL)
The DO pin indicates the Ready/Busy status of the
device, if CS is brought high after a minimum of 250 ns
low (TCSL).
The Erase All (ERAL) instruction will erase the entire
memory array to the logical ‘1’ state. The ERAL cycle
is identical to the erase cycle, except for the different
opcode. The ERAL cycle is completely self-timed and
commences at the falling edge of the CS, except on
‘93C’ devices where the rising edge of CLK before the
last data bit initiates the write cycle. Clocking of the
CLK pin is not necessary after the device has entered
the ERAL cycle.
FIGURE 2-3:
Note:
After the ERAL command is complete,
issuing a Start bit and then taking CS low
will clear the Ready/Busy status from DO.
VCC must be ≥4.5V for proper operation of ERAL.
ERAL TIMING FOR 93AA AND 93LC DEVICES
TCSL
CS
Check Status
CLK
DI
1
0
0
1
0
x
•••
x
TCZ
TSV
DO
High-Z
Busy
Ready
High-Z
TEC
VCC must be ≥4.5V for proper operation of ERAL.
FIGURE 2-4:
ERAL TIMING FOR 93C DEVICES
TCSL
CS
Check Status
CLK
DI
1
0
0
1
0
x
•••
x
TCZ
TSV
DO
High-Z
Busy
Ready
High-Z
TEC
DS21794F-page 8
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
2.6
Erase/Write Disable and Enable
(EWDS/EWEN)
Once the EWEN instruction is executed, programming
remains enabled until an EWDS instruction is executed
or Vcc is removed from the device.
The 93XX56A/B/C powers up in the Erase/Write
Disable (EWDS) state. All programming modes must be
preceded by an Erase/Write Enable (EWEN) instruction.
FIGURE 2-5:
To protect against accidental data disturbance, the
EWDS instruction can be used to disable all erase/write
functions and should follow all programming operations. Execution of a READ instruction is independent of
both the EWEN and EWDS instructions.
EWDS TIMING
TCSL
CS
CLK
1
DI
FIGURE 2-6:
0
0
0
0
•••
x
x
EWEN TIMING
TCSL
CS
CLK
2.7
0
1
DI
0
1
1
•••
x
Read
devices) output string. The output data bits will toggle on
the rising edge of the CLK and are stable after the specified time delay (TPD). Sequential read is possible when
CS is held high. The memory data will automatically cycle
to the next register and output sequentially.
The READ instruction outputs the serial data of the
addressed memory location on the DO pin. A dummy
zero bit precedes the 8-bit (if ORG pin is low or A-version
devices) or 16-bit (if ORG pin is high or B-version
FIGURE 2-7:
x
READ TIMING
CS
CLK
DI
DO
1
1
0
High-Z
© 2008 Microchip Technology Inc.
AN
•••
A0
0
Dx
•••
D0
Dx
•••
D0
Dx
•••
D0
DS21794F-page 9
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
2.8
Write
The DO pin indicates the Ready/Busy status of the
device, if CS is brought high after a minimum of 250 ns
low (TCSL). DO at logical ‘0’ indicates that programming
is still in progress. DO at logical ‘1’ indicates that the
register at the specified address has been written with
the data specified and the device is ready for another
instruction.
The WRITE instruction is followed by 8 bits (if ORG is
low or A-version devices) or 16 bits (if ORG pin is high
or B-version devices) of data which are written into the
specified address. For 93AA56A/B/C and 93LC56A/B/C
devices, after the last data bit is clocked into DI, the
falling edge of CS initiates the self-timed auto-erase and
programming cycle. For 93C56A/B/C devices, the selftimed auto-erase and programming cycle is initiated by
the rising edge of CLK on the last data bit.
FIGURE 2-8:
Note:
After the Write cycle is complete, issuing a
Start bit and then taking CS low will clear
the Ready/Busy status from DO.
WRITE TIMING FOR 93AA AND 93LC DEVICES
TCSL
CS
CLK
DI
1
0
1
AN
•••
A0
Dx
•••
D0
TSV
High-Z
DO
Busy
TCZ
Ready
High-Z
TWC
FIGURE 2-9:
WRITE TIMING FOR 93C DEVICES
TCSL
CS
CLK
DI
1
0
1
AN
•••
A0
Dx
•••
D0
TSV
DO
High-Z
Busy
TCZ
Ready
High-Z
TWC
DS21794F-page 10
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
2.9
Write All (WRAL)
The DO pin indicates the Ready/Busy status of the
device if CS is brought high after a minimum of 250 ns
low (TCSL).
The Write All (WRAL) instruction will write the entire
memory array with the data specified in the command.
For 93AA56A/B/C and 93LC56A/B/C devices, after the
last data bit is clocked into DI, the falling edge of CS
initiates the self-timed auto-erase and programming
cycle. For 93C56A/B/C devices, the self-timed autoerase and programming cycle is initiated by the rising
edge of CLK on the last data bit. Clocking of the CLK
pin is not necessary after the device has entered the
WRAL cycle. The WRAL command does include an
automatic ERAL cycle for the device. Therefore, the
WRAL instruction does not require an ERAL instruction,
but the chip must be in the EWEN status.
FIGURE 2-10:
Note:
After the Write All cycle is complete,
issuing a Start bit and then taking CS low
will clear the Ready/Busy status from DO.
VCC must be ≥4.5V for proper operation of WRAL.
WRAL TIMING FOR 93AA AND 93LC DEVICES
TCSL
CS
CLK
DI
1
0
0
0
1
x
•••
x
Dx
•••
D0
TSV
High-Z
DO
Busy
TCZ
Ready
HIGH-Z
TWL
VCC must be ≥4.5V for proper operation of WRAL.
FIGURE 2-11:
WRAL TIMING FOR 93C DEVICES
TCSL
CS
CLK
DI
1
0
0
0
1
x
•••
x
Dx
•••
D0
TSV
DO
High-Z
Busy
TCZ
Ready
HIGH-Z
TWL
© 2008 Microchip Technology Inc.
DS21794F-page 11
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
3.0
PIN DESCRIPTIONS
TABLE 3-1:
Name
CS
PIN DESCRIPTIONS
SOIC/PDIP/
MSOP/TSSOP/
DFN
SOT-23
Rotated SOIC
1
5
3
Function
Chip Select
CLK
2
4
4
Serial Clock
DI
3
3
5
Data In
DO
4
1
6
Data Out
VSS
5
2
7
Ground
ORG/NC
6
—
8
Organization/93XX56C
No Internal Connection/93XX56A/B
NC
7
—
1
No Internal Connection
VCC
8
6
2
Power Supply
3.1
Chip Select (CS)
A high level selects the device; a low level deselects
the device and forces it into Standby mode. However, a
programming cycle that is already in progress will be
completed, regardless of the Chip Select (CS) input
signal. If CS is brought low during a program cycle, the
device will go into Standby mode as soon as the
programming cycle is completed.
CS must be low for 250 ns minimum (TCSL) between
consecutive instructions. If CS is low, the internal
control logic is held in a Reset status.
3.2
Serial Clock (CLK)
The Serial Clock is used to synchronize the communication between a master device and the 93XX series
device. Opcodes, address and data bits are clocked in
on the positive edge of CLK. Data bits are also clocked
out on the positive edge of CLK.
CLK can be stopped anywhere in the transmission
sequence (at high or low level) and can be continued
anytime with respect to Clock High Time (TCKH) and
Clock Low Time (TCKL). This gives the controlling
master freedom in preparing opcode, address and
data.
CLK is a “don’t care” if CS is low (device deselected). If
CS is high, but the Start condition has not been
detected (DI = 0), any number of clock cycles can be
received by the device without changing its status (i.e.,
waiting for a Start condition).
CLK cycles are not required during the self-timed write
(i.e., auto erase/write) cycle.
After detection of a Start condition the specified number
of clock cycles (respectively low-to-high transitions of
CLK) must be provided. These clock cycles are
required to clock in all required opcode, address and
DS21794F-page 12
data bits before an instruction is executed. CLK and DI
then become “don’t care” inputs waiting for a new Start
condition to be detected.
3.3
Data In (DI)
Data In (DI) is used to clock in a Start bit, opcode,
address and data synchronously with the CLK input.
3.4
Data Out (DO)
Data Out (DO) is used in the Read mode to output data
synchronously with the CLK input (TPD after the
positive edge of CLK).
This pin also provides Ready/Busy status information
during erase and write cycles. Ready/Busy status information is available on the DO pin if CS is brought high
after being low for minimum Chip Select low time (TCSL)
and an erase or write operation has been initiated.
The Status signal is not available on DO if CS is held
low during the entire erase or write cycle. In this case,
DO is in the High-Z mode. If status is checked after the
erase/write cycle, the data line will be high to indicate
the device is ready.
Note:
3.5
After a programming cycle is complete,
issuing a Start bit and then taking CS low
will clear the Ready/Busy status from DO.
Organization (ORG)
When the ORG pin is connected to VCC or Logic HI, the
(x16) memory organization is selected. When the ORG
pin is tied to VSS or Logic LO, the (x8) memory
organization is selected. For proper operation, ORG
must be tied to a valid logic level.
93XX56A devices are always (x8) organization and
93XX56B devices are always (x16) organization.
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
4.0
PACKAGING INFORMATION
4.1
Package Marking Information
8-Lead MSOP (150 mil)
XXXXXXT
YWWNNN
6-Lead SOT-23
XXNN
Example:
3L56BI
5281L7
Example:
2EL7
8-Lead PDIP
Example:
XXXXXXXX
T/XXXNNN
YYWW
93LC56B
I/P e3 1L7
0528
8-Lead SOIC
Example:
XXXXXXXT
XXXXYYWW
NNN
93LC56BI
SN e3 0528
1L7
8-Lead TSSOP
Example:
XXXX
TYWW
NNN
8-Lead 2x3 DFN
XXX
YWW
NN
© 2008 Microchip Technology Inc.
L56B
I528
1L7
Example:
344
528
L7
DS21794F-page 13
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
1st Line Marking Codes
Part Number
93AA56A
SOT-23
DFN
TSSOP
MSOP
I Temp.
E Temp.
I Temp.
E Temp.
A56A
3A56AT
2BNN
—
331
—
93AA56B
A56B
3A56BT
2LNN
—
341
—
93AA56C
A56C
3A56CT
—
—
351
—
93LC56A
L56A
3L56AT
2ENN
2FNN
334
335
93LC56B
L56B
3L56BT
2PNN
2RNN
344
345
93LC56C
L56C
3L56CT
—
—
354
355
93C56A
C56A
3C56AT
2HNN
2JNN
337
338
93C56B
C56B
3C56BT
2TNN
2UNN
347
348
93C56C
C56C
3C56CT
—
—
357
358
Note:
T = Temperature grade (I, E)
NN = Alphanumeric traceability code
Legend: XX...X
T
Y
YY
WW
NNN
e3
Part number or part number code
Temperature (I, E)
Year code (last digit of calendar year)
Year code (last 2 digits of calendar year)
Week code (week of January 1 is week ‘01’)
Alphanumeric traceability code (2 characters for small packages)
Pb-free JEDEC designator for Matte Tin (Sn)
Note:
For very small packages with no room for the Pb-free JEDEC designator
e3 , the marking will only appear on the outer carton or reel label.
Note:
In the event the full Microchip part number cannot be marked on one line, it will
be carried over to the next line, thus limiting the number of available
characters for customer-specific information.
DS21794F-page 14
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
1
%&
%!%2") ' %
2$%
%"%
%%033)))&
&32
D
N
E
E1
NOTE 1
1
2
e
b
A2
A
c
φ
L
L1
A1
4%
& 5&%
6!&(
$
55**
6
6
67
8
9
%
7;%
<
:+./
<
""22
+
9+
+
%"
$$
<
+
7="%
*
""2="%
*
,./
75%
,./
1
%5%
5
1
%%
5
./
:
9
+*1
1
%
>
<
9>
5"2
9
<
,
5"="%
(
<
!"#$%!&'(!%&! %(
%")%%%"
& "*"
%!"&
"$ %! "$ %! %#"+&& "
, & "%
*-+
./0 . & %#%! ))%
!%%
*10 $& '! !)%
!%%
'$
$
&%
!
) /.
© 2008 Microchip Technology Inc.
DS21794F-page 15
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
!"
1
%&
%!%2") ' %
2$%
%"%
%%033)))&
&32
b
4
N
E
E1
PIN 1 ID BY
LASER MARK
1
2
3
e
e1
D
A
A2
c
φ
L
A1
L1
4%
& 5&%
6!&(
$
55**
6
6
67
8
:
%
+./
7!% "5"%
./
7;%
<
""22
9
<
+
,
%"
$$
<
+
7="%
*
<
,
""2="%
*
,
<
9
75%
<
,
1
%5%
5
<
:
1
%%
5
,+
<
9
1
%
>
<
,>
5"2
9
<
:
5"="%
(
<
+
& "*"
%!"&
"$ %! "$ %! %#"&& "
& "%
*-+
./0 . & %#%! ))%
!%%
) /9.
DS21794F-page 16
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
#
$%"&&
'(#$
1
%&
%!%2") ' %
2$%
%"%
%%033)))&
&32
N
NOTE 1
E1
1
3
2
D
E
A2
A
L
A1
c
e
eB
b1
b
4%
& 5&%
6!&(
$
6/;*
6
6
67
8
9
%
%
%
<
<
""22
+
,
+
. %
%
+
<
<
!"%
!"="%
*
,
,+
""2="%
*
+
9
75%
,9
,:+
%
%
5
+
,
+
5"2
9
+
(
:
(
9
.
<
<
45"="%
5
)5"="%
7
)?
./
,
!"#$%!&'(!%&! %(
%")%%%"
?$%/% %
, & "*"
%!"&
"$ %! "$ %! %#"@ "
& "%
*-+
./0. & %#%! ))%
!%%
) /9.
© 2008 Microchip Technology Inc.
DS21794F-page 17
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
%)*"+,&'($-
1
%&
%!%2") ' %
2$%
%"%
%%033)))&
&32
D
e
N
E
E1
NOTE 1
1
2
3
α
h
b
h
A2
A
c
φ
L
A1
L1
4%
& 5&%
6!&(
$
β
55**
6
6
67
8
9
%
7;%
<
./
<
""22
+
<
<
%"
$$?
<
+
7="%
*
""2="%
*
,./
75%
./
+
:./
/&$A
%
B
+
<
+
1
%5%
5
<
1
%%
5
*1
1
%
I
>
<
9>
5"2
<
+
5"="%
(
,
<
+
"$%
D
+>
<
+>
"$%.
%%
&
E
+>
<
+>
!"#$%!&'(!%&! %(
%")%%%"
?$%/% %
, & "*"
%!"&
"$ %! "$ %! %#"+&& "
& "%
*-+
./0 . & %#%! ))%
!%%
*10 $& '! !)%
!%%
'$
$
&%
!
) /+.
DS21794F-page 18
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
%)*"+,&'($-
1
%&
%!%2") ' %
2$%
%"%
%%033)))&
&32
© 2008 Microchip Technology Inc.
DS21794F-page 19
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
..
%/+/'( 1
%&
%!%2") ' %
2$%
%"%
%%033)))&
&32
D
N
E
E1
NOTE 1
1
2
b
e
c
A
φ
A2
A1
L
L1
4%
& 5&%
6!&(
$
55**
6
6
67
8
9
%
7;%
<
:+./
<
""22
9
+
%"
$$
+
<
+
7="%
*
""2="%
*
,
:./
""25%
,
,
1
%5%
5
+
:
+
1
%%
5
+
*1
1
%
I
>
<
9>
5"2
<
5"="%
(
<
,
!"#$%!&'(!%&! %(
%")%%%"
& "*"
%!"&
"$ %! "$ %! %#"+&& "
, & "%
*-+
./0 . & %#%! ))%
!%%
*10 $& '! !)%
!%%
'$
$
&%
!
) /9:.
DS21794F-page 20
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
#
0
*-%!1"1&+,'(#0
1
%&
%!%2") ' %
2$%
%"%
%%033)))&
&32
D
e
b
N
N
L
K
E2
E
EXPOSED PAD
NOTE 1
2
1
2
NOTE 1
1
D2
BOTTOM VIEW
TOP VIEW
A
A3
A1
NOTE 2
4%
& 5&%
6!&(
$
55**
6
6
67
8
9
%
7;%
9
%"
$$
+
/
%%2
,
*1
75%
./
7="%
*
*#
""5%
,
<
*#
""="%
*
+
<
+
(
+
,
/
%%5%
5
,
+
/
%%%
*#
""
C
<
<
/
%%="%
+./
,./
!"#$%!&'(!%&! %(
%")%%%"
2&
&
#
"%( %" , 2 ) !%"
& "%
*-+
./0 . & %#%! ))%
!%%
*10 $& '! !)%
!%%
'$
$
&%
!
++
) /,/
© 2008 Microchip Technology Inc.
DS21794F-page 21
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
#
0
*-%!1"1&+,'(#0
1
%&
%!%2") ' %
2$%
%"%
%%033)))&
&32
DS21794F-page 22
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
APPENDIX A:
REVISION HISTORY
Revision B
Corrections to Section 1.0, Electrical Characteristics.
Section 4.1, 6-Lead SOT-23 package to OT.
Revision C
Added DFN package.
Revision D (11/2006)
Updated Package Drawings and Product ID System
Revision E (3/2007)
Replaced Package Drawings; Revised Product ID
System (SOIC-SN package).
Revision F (5/2008)
Revised Figures 2-1 through 2-4 and Figures 2-8
through 2-11; Revised Package Marking Information;
Replaced Package Drawings; Revised Product ID
section.
© 2008 Microchip Technology Inc.
DS21794F-page 23
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
Notes:
DS21794F-page 24
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
THE MICROCHIP WEB SITE
CUSTOMER SUPPORT
Microchip provides online support via our WWW site at
www.microchip.com. This web site is used as a means
to make files and information easily available to
customers. Accessible by using your favorite Internet
browser, the web site contains the following
information:
Users of Microchip products can receive assistance
through several channels:
• Product Support – Data sheets and errata,
application notes and sample programs, design
resources, user’s guides and hardware support
documents, latest software releases and archived
software
• General Technical Support – Frequently Asked
Questions (FAQ), technical support requests,
online discussion groups, Microchip consultant
program member listing
• Business of Microchip – Product selector and
ordering guides, latest Microchip press releases,
listing of seminars and events, listings of
Microchip sales offices, distributors and factory
representatives
•
•
•
•
•
Distributor or Representative
Local Sales Office
Field Application Engineer (FAE)
Technical Support
Development Systems Information Line
Customers
should
contact
their
distributor,
representative or field application engineer (FAE) for
support. Local sales offices are also available to help
customers. A listing of sales offices and locations is
included in the back of this document.
Technical support is available through the web site
at: http://support.microchip.com
CUSTOMER CHANGE NOTIFICATION
SERVICE
Microchip’s customer notification service helps keep
customers current on Microchip products. Subscribers
will receive e-mail notification whenever there are
changes, updates, revisions or errata related to a
specified product family or development tool of interest.
To register, access the Microchip web site at
www.microchip.com, click on Customer Change
Notification and follow the registration instructions.
© 2008 Microchip Technology Inc.
DS21794F-page 25
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation
can better serve you, please FAX your comments to the Technical Publications Manager at (480) 792-4150.
Please list the following information, and use this outline to provide us with your comments about this document.
To:
Technical Publications Manager
RE:
Reader Response
Total Pages Sent ________
From: Name
Company
Address
City / State / ZIP / Country
Telephone: (_______) _________ - _________
FAX: (______) _________ - _________
Application (optional):
Would you like a reply?
Y
N
Device: 93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
Literature Number: DS21794F
Questions:
1. What are the best features of this document?
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this document easy to follow? If not, why?
4. What additions to the document do you think would enhance the structure and subject?
5. What deletions from the document could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
DS21794F-page 26
© 2008 Microchip Technology Inc.
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office.
PART NO.
Device
X
X
Pinout Tape & Reel Temperature
Range
Device:
/XX
X
Package
93AA56A: 2K 1.8V Microwire Serial EEPROM
93AA56B: 2K 1.8V Microwire Serial EEPROM
93AA56C: 2K 1.8V Microwire Serial EEPROM w/ORG
93LC56A: 2K 2.5V Microwire Serial EEPROM
93LC56B: 2K 2.5V Microwire Serial EEPROM
93LC56C: 2K 2.5V Microwire Serial EEPROM w/ORG
93C56A:
93C56B:
93C56C:
Pinout:
Tape & Reel:
Blank
X
=
=
2K 5.0V Microwire Serial EEPROM
2K 5.0V Microwire Serial EEPROM
2K 5.0V Microwire Serial EEPROM w/ORG
Standard pinout
Rotated pinout
Blank =
T
=
Standard packaging
Tape & Reel
Temperature Range:
I
E
=
=
-40°C to +85°C
-40°C to +125°C
Package:
MS
OT
P
SN
ST
MC
=
=
=
=
=
=
Plastic MSOP (Micro Small outline, 8-lead)
SOT-23, 6-lead (Tape & Reel only)
Plastic DIP (300 mil body), 8-lead
Plastic SOIC (3.90 mm body), 8-lead
TSSOP, 8-lead
2x3 DFN, 8-lead
© 2008 Microchip Technology Inc.
Examples:
a)
b)
c)
93AA56C-I/MS: 2K, 256x8 or 128x16 Serial
EEPROM, MSOP package, 1.8V
93AA56B-I/MS: 2K, 128x16 Serial EEPROM,
MSOP package, 1.8V
93AA56AT-I/OT: 2K, 256x8 Serial EEPROM,
SOT-23 package, tape and reel, 1.8V
d)
93AA56CT-I/MS: 2K, 256x8 or 128x16 Serial
EEPROM, MSOP package, tape and reel, 1.8V
a)
93LC56A-I/MS: 2K, 256x8 Serial EEPROM,
MSOP package, 2.5V
93LC56BT-I/OT: 2K, 128x16 Serial EEPROM,
SOT-23 package, tape and reel, 2.5V
93LC56B-I/MS: 2K, 128x16 Serial EEPROM,
MSOP package, 2.5V
b)
c)
a)
b)
c)
93C56B-I/MS: 2K, 128x16 Serial EEPROM,
MSOP package, 5.0V
93C56C-I/MS: 2K, 256x8 or 128x16 Serial
EEPROM, MSOP package, 5.0V
93C56AT-I/OT: 2K, 256x8 Serial EEPROM,
SOT-23 package, tape and reel, 5.0V
DS21794F-page 27
93AA56A/B/C, 93LC56A/B/C, 93C56A/B/C
NOTES:
DS21794F-page 28
© 2008 Microchip Technology Inc.
Note the following details of the code protection feature on Microchip devices:
•
Microchip products meet the specification contained in their particular Microchip Data Sheet.
•
Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the
intended manner and under normal conditions.
•
There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our
knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip’s Data
Sheets. Most likely, the person doing so is engaged in theft of intellectual property.
•
Microchip is willing to work with the customer who is concerned about the integrity of their code.
•
Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not
mean that we are guaranteeing the product as “unbreakable.”
Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our
products. Attempts to break Microchip’s code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts
allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act.
Information contained in this publication regarding device
applications and the like is provided only for your convenience
and may be superseded by updates. It is your responsibility to
ensure that your application meets with your specifications.
MICROCHIP MAKES NO REPRESENTATIONS OR
WARRANTIES OF ANY KIND WHETHER EXPRESS OR
IMPLIED, WRITTEN OR ORAL, STATUTORY OR
OTHERWISE, RELATED TO THE INFORMATION,
INCLUDING BUT NOT LIMITED TO ITS CONDITION,
QUALITY, PERFORMANCE, MERCHANTABILITY OR
FITNESS FOR PURPOSE. Microchip disclaims all liability
arising from this information and its use. Use of Microchip
devices in life support and/or safety applications is entirely at
the buyer’s risk, and the buyer agrees to defend, indemnify and
hold harmless Microchip from any and all damages, claims,
suits, or expenses resulting from such use. No licenses are
conveyed, implicitly or otherwise, under any Microchip
intellectual property rights.
Trademarks
The Microchip name and logo, the Microchip logo, Accuron,
dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro,
PICSTART, PRO MATE, rfPIC and SmartShunt are registered
trademarks of Microchip Technology Incorporated in the
U.S.A. and other countries.
FilterLab, Linear Active Thermistor, MXDEV, MXLAB,
SEEVAL, SmartSensor and The Embedded Control Solutions
Company are registered trademarks of Microchip Technology
Incorporated in the U.S.A.
Analog-for-the-Digital Age, Application Maestro, CodeGuard,
dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN,
ECONOMONITOR, FanSense, In-Circuit Serial
Programming, ICSP, ICEPIC, Mindi, MiWi, MPASM, MPLAB
Certified logo, MPLIB, MPLINK, mTouch, PICkit, PICDEM,
PICDEM.net, PICtail, PIC32 logo, PowerCal, PowerInfo,
PowerMate, PowerTool, REAL ICE, rfLAB, Select Mode, Total
Endurance, UNI/O, WiperLock and ZENA are trademarks of
Microchip Technology Incorporated in the U.S.A. and other
countries.
SQTP is a service mark of Microchip Technology Incorporated
in the U.S.A.
All other trademarks mentioned herein are property of their
respective companies.
© 2008, Microchip Technology Incorporated, Printed in the
U.S.A., All Rights Reserved.
Printed on recycled paper.
Microchip received ISO/TS-16949:2002 certification for its worldwide
headquarters, design and wafer fabrication facilities in Chandler and
Tempe, Arizona; Gresham, Oregon and design centers in California
and India. The Company’s quality system processes and procedures
are for its PIC® MCUs and dsPIC® DSCs, KEELOQ® code hopping
devices, Serial EEPROMs, microperipherals, nonvolatile memory and
analog products. In addition, Microchip’s quality system for the design
and manufacture of development systems is ISO 9001:2000 certified.
© 2008 Microchip Technology Inc.
DS21749F-page 29
WORLDWIDE SALES AND SERVICE
AMERICAS
ASIA/PACIFIC
ASIA/PACIFIC
EUROPE
Corporate Office
2355 West Chandler Blvd.
Chandler, AZ 85224-6199
Tel: 480-792-7200
Fax: 480-792-7277
Technical Support:
http://support.microchip.com
Web Address:
www.microchip.com
Asia Pacific Office
Suites 3707-14, 37th Floor
Tower 6, The Gateway
Harbour City, Kowloon
Hong Kong
Tel: 852-2401-1200
Fax: 852-2401-3431
India - Bangalore
Tel: 91-80-4182-8400
Fax: 91-80-4182-8422
India - New Delhi
Tel: 91-11-4160-8631
Fax: 91-11-4160-8632
Austria - Wels
Tel: 43-7242-2244-39
Fax: 43-7242-2244-393
Denmark - Copenhagen
Tel: 45-4450-2828
Fax: 45-4485-2829
India - Pune
Tel: 91-20-2566-1512
Fax: 91-20-2566-1513
France - Paris
Tel: 33-1-69-53-63-20
Fax: 33-1-69-30-90-79
Japan - Yokohama
Tel: 81-45-471- 6166
Fax: 81-45-471-6122
Germany - Munich
Tel: 49-89-627-144-0
Fax: 49-89-627-144-44
Atlanta
Duluth, GA
Tel: 678-957-9614
Fax: 678-957-1455
Boston
Westborough, MA
Tel: 774-760-0087
Fax: 774-760-0088
Chicago
Itasca, IL
Tel: 630-285-0071
Fax: 630-285-0075
Dallas
Addison, TX
Tel: 972-818-7423
Fax: 972-818-2924
Detroit
Farmington Hills, MI
Tel: 248-538-2250
Fax: 248-538-2260
Kokomo
Kokomo, IN
Tel: 765-864-8360
Fax: 765-864-8387
Los Angeles
Mission Viejo, CA
Tel: 949-462-9523
Fax: 949-462-9608
Santa Clara
Santa Clara, CA
Tel: 408-961-6444
Fax: 408-961-6445
Toronto
Mississauga, Ontario,
Canada
Tel: 905-673-0699
Fax: 905-673-6509
Australia - Sydney
Tel: 61-2-9868-6733
Fax: 61-2-9868-6755
China - Beijing
Tel: 86-10-8528-2100
Fax: 86-10-8528-2104
China - Chengdu
Tel: 86-28-8665-5511
Fax: 86-28-8665-7889
Korea - Daegu
Tel: 82-53-744-4301
Fax: 82-53-744-4302
China - Hong Kong SAR
Tel: 852-2401-1200
Fax: 852-2401-3431
Korea - Seoul
Tel: 82-2-554-7200
Fax: 82-2-558-5932 or
82-2-558-5934
China - Nanjing
Tel: 86-25-8473-2460
Fax: 86-25-8473-2470
Malaysia - Kuala Lumpur
Tel: 60-3-6201-9857
Fax: 60-3-6201-9859
China - Qingdao
Tel: 86-532-8502-7355
Fax: 86-532-8502-7205
Malaysia - Penang
Tel: 60-4-227-8870
Fax: 60-4-227-4068
China - Shanghai
Tel: 86-21-5407-5533
Fax: 86-21-5407-5066
Philippines - Manila
Tel: 63-2-634-9065
Fax: 63-2-634-9069
China - Shenyang
Tel: 86-24-2334-2829
Fax: 86-24-2334-2393
Singapore
Tel: 65-6334-8870
Fax: 65-6334-8850
China - Shenzhen
Tel: 86-755-8203-2660
Fax: 86-755-8203-1760
Taiwan - Hsin Chu
Tel: 886-3-572-9526
Fax: 886-3-572-6459
China - Wuhan
Tel: 86-27-5980-5300
Fax: 86-27-5980-5118
Taiwan - Kaohsiung
Tel: 886-7-536-4818
Fax: 886-7-536-4803
China - Xiamen
Tel: 86-592-2388138
Fax: 86-592-2388130
Taiwan - Taipei
Tel: 886-2-2500-6610
Fax: 886-2-2508-0102
China - Xian
Tel: 86-29-8833-7252
Fax: 86-29-8833-7256
Thailand - Bangkok
Tel: 66-2-694-1351
Fax: 66-2-694-1350
Italy - Milan
Tel: 39-0331-742611
Fax: 39-0331-466781
Netherlands - Drunen
Tel: 31-416-690399
Fax: 31-416-690340
Spain - Madrid
Tel: 34-91-708-08-90
Fax: 34-91-708-08-91
UK - Wokingham
Tel: 44-118-921-5869
Fax: 44-118-921-5820
China - Zhuhai
Tel: 86-756-3210040
Fax: 86-756-3210049
01/02/08
DS21794F-page 30
© 2008 Microchip Technology Inc.