STMICROELECTRONICS STMPS2151MTR

STMPS2141, STMPS2151
STMPS2161, STMPS2171
Enhanced single channel power switches
Features
■
90 mΩ high-side MOSFET switch
■
500/1000 mA continuous current
■
Thermal and short-circuit protection with
overcurrent logic output
■
Operating range from 2.7 V to 5.5 V
■
CMOS- and TTL-compatible enable inputs
■
Undervoltage lockout (UVLO)
■
12 µA maximum standby supply current
■
Ambient temperature range, -40°C to 85°C
■
8 kV ESD protection
■
Reverse current protection
■
Fault-blanking
SOT23-5L
SO-8
MSOP8
Description
The STMPS2141, STMPS2151, STMPS2161,
STMPS2171 power distribution switches are
intended for applications where heavy capacitive
loads and short circuits are likely to be
encountered. These devices incorporate 90 mΩ
N-channel MOSFET high-side power switches for
power-distribution. These switches are controlled
by a logic enable input.
Table 1.
When the output load exceeds the current-limit
threshold or a short is present, the device limits
the output current to a safe level by switching into
a constant-current mode. When continuous heavy
overloads and short circuits increase the power
dissipation in the switch, causing the junction
temperature to rise, a thermal protection circuit
shuts the switch off to prevent damage. Recovery
from a thermal shutdown is automatic once the
device has cooled sufficiently. Internal circuitry
ensures the switch remains off until a valid input
voltage is present.
Device summary
Order codes
SO-8
SOT23-5L
Current limit
MSOP8(1)
(mA)
Enable
STMPS2141MTR
STMPS2141STR
STMPS2141TTR
500
Active low
STMPS2151MTR
STMPS2151STR
STMPS2151TTR
500
Active high
STMPS2161MTR
STMPS2161STR
STMPS2161TTR
1000
Active low
STMPS2171MTR
STMPS2171STR
STMPS2171TTR
1000
Active high
1. MSOP8 package is also known as “TSSOP8”
July 2009
Doc ID 13793 Rev 4
1/34
www.st.com
34
Contents
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Contents
1
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2
Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3
2.1
Pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.1
Fault blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.2
Overcurrent/over-temperature protection . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.3
FAULT conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3.4
Reversed current blocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3.5
UVLO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4
Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
5
Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.1
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5.2
Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
6
Electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
7
Detail device characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7.1
7.2
2/34
STMPS2141, STMPS2151 additional electrical charts . . . . . . . . . . . . . . 16
7.1.1
Turn on/off characteristics at VOUT = 5.0 V . . . . . . . . . . . . . . . . . . . . . 16
7.1.2
Turn on/off characteristics at VOUT = 3.0 V . . . . . . . . . . . . . . . . . . . . . 17
7.1.3
UVLO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.1.4
OC protection characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.1.5
Other electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
STMPS2161, STMPS2171 electrical charts . . . . . . . . . . . . . . . . . . . . . . 21
7.2.1
Turn on/off characteristics at VOUT = 5.0 V . . . . . . . . . . . . . . . . . . . . . 21
7.2.2
Turn on/off characteristics at VOUT = 3.0 V . . . . . . . . . . . . . . . . . . . . . 22
7.2.3
UVLO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
7.2.4
OC protection characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
7.2.5
Other electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Contents
8
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
9
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Doc ID 13793 Rev 4
3/34
List of figures
STMPS2141, STMPS2151, STMPS2161, STMPS2171
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
Figure 20.
Figure 21.
Figure 22.
Figure 23.
Figure 24.
Figure 25.
Figure 26.
Figure 27.
Figure 28.
Figure 29.
Figure 30.
Figure 31.
Figure 32.
Figure 33.
Figure 34.
Figure 35.
Figure 36.
Figure 37.
Figure 38.
Figure 39.
Figure 40.
Figure 41.
Figure 42.
Figure 43.
Figure 44.
Figure 45.
Figure 46.
Figure 47.
Figure 48.
4/34
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
SOT23-5L, SO-8 and MSOP8 pin connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Voltage output turn on delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Voltage output turn off delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Current output turn on delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Current output turn off delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Voltage output turn on delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Voltage output turn off delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Current output turn on delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Current output turn off delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
UVLO rising . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
UVLO falling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
OC protection at VOUT = 3.0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
OC protection at VOUT = 3.0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
OC protection at VOUT = 5.0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
OC protection at VOUT = 5.0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ICC vs VIN (enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ICC vs temperature (enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
ICC vs VIN (disabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ICC vs temperature (disabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
RDS ON vs VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
RDS ON vs temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ILIMIT vs temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Switch leakage vs temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Output rise time vs. VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Output fall time vs. VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
UVLO vs temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Voltage output turn on delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Voltage output turn off delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Current output turn on delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Current output turn off delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Voltage output turn on delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Voltage output turn off delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Current output turn on delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Current output turn off delay time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
UVLO rising . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
UVLO falling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
OC protection at VOUT = 3.0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
OC protection at VOUT = 3.0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
OC protection at VOUT = 5.0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
OC protection at VOUT = 5.0 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
ICC vs VIN (enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ICC vs temperature (enabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ICC vs VIN (disabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ICC vs temperature (disabled) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
RDS ON vs VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
RDS ON vs temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ILIMIT vs temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Figure 49.
Figure 50.
Figure 51.
Figure 52.
Figure 53.
Figure 54.
Figure 55.
Figure 56.
Figure 57.
Figure 58.
Figure 59.
Figure 60.
Figure 61.
List of figures
Switch leakage vs temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Output rise time vs. VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Output fall time vs. VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
UVLO vs temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SOT23-5L package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
SOT23-5L footprint recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SOT23-5L carrier tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SOT23-5L reel information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SO-8 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
MSOP8 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SO-8 carrier tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
MSOP8 carrier tape . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Reel information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Doc ID 13793 Rev 4
5/34
List of tables
STMPS2141, STMPS2151, STMPS2161, STMPS2171
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Table 17.
Table 18.
Table 19.
Table 20.
Table 21.
Table 22.
6/34
Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
FAULT conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SOT23-5L (160 °C/W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
MSOP8 (220 °C/W) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SO-8 (160 °C/W). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
SOT-23-5L electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
MSO8P/SO8 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Current limit characteristics
(VI = 5.5 V, IO = rated current, TJ = 25°C, unless otherwise specified) . . . . . . . . . . . . . . . 14
Supply current characteristics
(VI = 5.5 V, IO = rated current, TJ = 25°C, unless otherwise specified) . . . . . . . . . . . . . . . 14
Thermal characteristics
(VI = 5.5 V, IO = rated current, TJ = 25°C, unless otherwise specified) . . . . . . . . . . . . . . . 15
UVLO characteristics
(VI = 5.5 V, IO = rated current, TJ = 25°C, unless otherwise specified) . . . . . . . . . . . . . . . 15
OC pin characteristics
(VI = 5.5 V, IO = rated current, TJ = 25°C, unless otherwise specified) . . . . . . . . . . . . . . . 15
EN pin characteristics
(VI = 5.5 V, IO = rated current, TJ = 25°C, unless otherwise specified) . . . . . . . . . . . . . . . 15
SOT23-5L mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
SOT23-5L footprint dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
SO-8 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
MSOP8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Reel mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
1
Block diagram
Block diagram
Figure 1.
Block diagram
VIN
VOUT
Current
sense
EN
Driver
UVLO
Thermal
sense
Fault blanking/reporting
driver control unit
Doc ID 13793 Rev 4
Fault
7/34
Pin settings
STMPS2141, STMPS2151, STMPS2161, STMPS2171
2
Pin settings
2.1
Pin connections
Figure 2.
SOT23-5L, SO-8 and MSOP8 pin connections
OUT
1
GND
2
FAULT
3
5
IN
4
EN
SOT23-5L
GND
1
8
OUT
IN
2
7
OUT
IN
3
6
OUT
EN_N
4
5
FAULT
SO-8 / MSOP8
2.2
Pin description
Table 2.
Pin description
Pin number
Name
8/34
Function
SO8
MSOP8
SOT23-5L
1
1
2
GND
2
2
5
IN
2.7 V - 5.5 V input
3
3
-
IN
2.7 V - 5.5 V input
4
4
4
EN
Enable for power switch
5
5
3
FAULT
6
6
1
OUT
Output of power switch
7
7
-
OUT
Output of power switch
8
8
-
OUT
Output of power switch
Doc ID 13793 Rev 4
Ground
Open drain FAULT indicator, active low
STMPS2141, STMPS2151, STMPS2161, STMPS2171
3
Functional description
3.1
Fault blanking
Functional description
The STMPS devices feature a 10 ms fault blanking. Fault blanking allows current-limit faults,
including momentary short-circuit faults that occur when hot-swapping a capacitive load,
and also ensures that no fault is issued during power-up. When a load transient causes the
device to enter current limit, an internal counter starts. If the load fault persists beyond the
10 ms fault-blanking timeout, the FAULT output asserts “low”. Load-transient faults less than
10 ms (typ.) do not cause a FAULT output assertion. Only current-limit faults are blanked.
Die over-temperature faults and input voltage drops below the UVLO threshold cause an
immediate fault output.
3.2
Overcurrent/over-temperature protection
In overcurrent or short-circuit condition, the switch limits the current at a value of about
120% of the rated current. If the temperature of the die goes above the limit value, the switch
turns off.
3.3
FAULT conditions
In power switch applications, 4 types of FAULT conditions are common. These fault
conditions and the response of the STMPS21x1 power switches are described in the
following Table 3.
Table 3.
FAULT conditions
Fault
Condition
STMPS21x1 action
Short circuit
Output shorted to GND via resistance
path of < 1 Ω, causing a rapid current
surge.
Reduces output voltage to reduce the
current. Asserts FAULT pin after a
blanking period
Over-current
Output connected to a load that sinks
current above threshold.
Reduces output voltage to reduce the
current. Asserts FAULT pin after a
blanking period.
Overheating
Turn OFF output until temperature falls
Temperature of junction exceeds 135°C
below 125°C. Asserts FAULT pin
due to any reason.
immediately.
Undervoltage
Input voltage drops below the UVLO
treshold.
Doc ID 13793 Rev 4
Turn OFF output until input voltage rises
above the UVLO treshold plus hysteresis.
Asserts FAULT pin immediately.
9/34
Functional description
3.4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Reversed current blocking
When the switch is OFF (disabled through the EN pin), or when the STMPS device is unpowered (VCC = 0 V) the switch behaves as an Hi-Z at the output pin, ensuring that no
reverse current will flow into the device when Vi < Vo .
Note:
In the case where the switch is ON, and a voltage higher than VIN is applied to the OUT pin,
a reverse current occurs. This operating condition is not allowed.
3.5
UVLO
When the input voltage drops below critical values, the power switch turns off to prevent
improper operation due to low voltage.
10/34
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
4
Ambient temperature
Ambient temperature
In Enable operating mode, an amount of power is dissipated as heat in the power switch due
to the on-resistance. The power dissipation is: P = I2R.
Table 4.
SOT23-5L (160 °C/W)
Part number
Temperature
difference
Maximum ambient
temperature
(junction and
ambient)
(at junction
temperature 125 °C)
32.5 mW
6.2
118.8
130.0 mW
24.8
100.2
Max current
Max RON at
5V
Power
dissipation
0.50 A
130 mΩ
1.00 A
130 mΩ
STMPS2141
STMPS2151
STMPS2161
STMPS2171
Table 5.
MSOP8 (220 °C/W)
Part number
Temperature
difference
Maximum ambient
temperature
(junction and
ambient)
(at junction temperature
125 °C)
32.5 mW
7.2
117.8
130.0 mW
28.6
96.4
Max
current
Max RON
at 5 V
Power
dissipation
0.50 A
130 mΩ
1.00 A
130 mΩ
STMPS2141
STMPS2151
STMPS2161
STMPS2171
Table 6.
SO-8 (160 °C/W)
Part number
Max RON
Max current
at 5 V
Power
dissipation
Temperature
difference (junction
and ambient)
Maximum ambient
temperature
(at junction temperature
125 °C)
STMPS2141
0.50 A
130 mΩ
32.5 mΩ
5.2
124.8
1.00 A
130 mΩ
130.0 mΩ
20.8
104.2
STMPS2151
STMPS2161
STMPS2171
Doc ID 13793 Rev 4
11/34
Maximum ratings
5
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Maximum ratings
Stressing the device above the rating listed in the “absolute maximum ratings” table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the operating sections of
this specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
5.1
Absolute maximum ratings
Table 7.
Absolute maximum ratings
Symbol
Value
Unit
–0.3 – 6.0
V
–0.3 – (Vi+0.3)
V
-0.3 – 6.0
V
Internally limited
−
8
kV
Junction operating temperature
–40 to 125
°C
Storage temperature
–55 to 150
°C
VI
Input voltage range
VO
Output voltage range
VIENX
IO
ESD
TJ
TSTG
5.2
Parameter
EN Input voltage range
Continuous output current
ESD protection level
TR
Thermal resistance (MSOP8)
220
°C/W
TR
Thermal resistance (SOT23-5L)
191
°C/W
TR
Thermal resistance (SO-8)
160
°C/W
Recommended operating conditions
Table 8.
Recommended operating conditions
Value
Symbol
12/34
Parameter
Unit
Min
Typ
Max
2.7
5.0
5.5
V
VI
Input voltage
VO
Output voltage
0
5.0
5.5
V
IO
(STMPS2141
STMPS2151)
Continuous output current
0
-
500
mA
IO
(STMPS2161
STMPS2171)
Continuous output current
0
-
1000
mA
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
6
Electrical specifications
Electrical specifications
Table 9.
SOT-23-5L electrical characteristics
Value
Symbol
Rds on
Rds on
Tr
Table 10.
Parameter
Static drain source
ON state resistance
SOT23-5L package
load = 500 mA
(STMPS2141/
STMPS2151)
load = 1000 mA
(STMPS2161/
STMPS2171)
Static drain source
ON state resistance
Output rise time
Test condition
Unit
Min
Typ
Max
VI = 2.7 V ; TJ = 25°C;
−
120
160
mΩ
VI = 5.0 V ; TJ = 25°C;
−
90
110
mΩ
VI = 2.7 V ; 40 < TJ < 125 °C
−
−
200
VI = 5.0 V ; 40 < TJ < 125 °C
−
−
135
0.05
−
2
VI = 5.0 V RL = 10 Ω
CL = 1 µF
mΩ
mS
MSO8P/SO8 electrical characteristics
Value
Symbol
Rds on
Rds on
Tr
Parameter
Test condition
Typ
Max
−
130
170
mΩ
−
110
125
mΩ
VI = 2.7 V
-40 < TJ < 125 °C
−
−
200
VI = 5.0 V
-40 < TJ < 125 °C
−
−
140
0.05
−
2
Static drain source
VI = 2.7 V ; TJ = 25°C
ON state resistance
SO-8 and MSO8 package
load = 500 mA
(STMPS2141/
VI = 5.0 V ; TJ = 25°C
STMPS2151)
load = 1000 mA
(STMPS2161/
STMPS2171)
Static drain source
ON state resistance
Output rise time
Unit
Min
VI = 5.0 V RL = 10 Ω
CL = 1 µF
Doc ID 13793 Rev 4
mΩ
mS
13/34
Electrical specifications
Table 11.
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Current limit characteristics
(VI = 5.5 V, IO = rated current, TJ = 25°C, unless otherwise specified)
Value
Symbol
Parameter
Test condition
IOS
Overcurrent limiting
(STMPS2141
threshold
STMPS2151)
IOS
Overcurrent limiting
(STMPS2161
threshold
STMPS2171)
IOS
(2141,2151)
Short circuit output
current
IOS
(2161,2171)
Short circuit output
current
Table 12.
Unit
Min
Typ
Max
0.60
0.80
1.00
A
1.10
1.50
1.90
A
−
−
0.9
A
−
−
1.8
A
VI = 5 V
VOUT = 4.5 V
VI = 5 V, OUT
connected to GND,
device enabled into
short circuit
Supply current characteristics
(VI = 5.5 V, IO = rated current, TJ = 25°C, unless otherwise specified)
Value
Symbol
Parameter
Ioff
Switch turned off
Ion
Switch turned on
Ileakage
Ireverse
Output leakage
current (1)
Reversed leakage
current
Test condition
Unit
Min
Typ
Max
No load
−
6.0
12
No load;
-40 < TJ < 125 °C
−
−
15
No load
−
40
60
No load;
-40 < TJ < 125 °C
−
−
70
Output grounded,
switch is OFF
−
−
2
µA
µA
µA
Output grounded,
switch is OFF;
-40 < TJ < 125°C
−
−
5
Switch is off, Vi < Vo,
output connected to
5.5 V, 25 °C
−
0.5
2
µA
Switch is off, Vi < Vo,
output connected to
5.5 V, 125 °C
−
0.5
3
1. Ileakage = Ioff-ground - Ioff, where Ioff-ground = current into Vin when switch is off and output is grounded
14/34
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Table 13.
Electrical specifications
Thermal characteristics
(VI = 5.5 V, IO = rated current, TJ = 25°C, unless otherwise specified)
Value
Symbol
Parameter
T1
Thermal shutdown
threshold
T2
Recovery from thermal
shutdown
Hysteresis
Table 14.
Test condition
-
Unit
Min
Typ
Max
−
−
145
°C
120
−
−
°C
−
14
−
°C
UVLO characteristics
(VI = 5.5 V, IO = rated current, TJ = 25°C, unless otherwise specified)
Value
Symbol
Parameter
Undervoltage lockout
threshold
VUVLO
Hysteresis
Table 15.
Test condition
-
Unit
Min
Typ
Max
2.0
−
2.5
V
40
75
110
mV
OC pin characteristics
(VI = 5.5 V, IO = rated current, TJ = 25°C, unless otherwise specified)
Value
Symbol
Parameter
OC Blanking
VO
IOFF
Table 16.
Test condition
OCx assertion and deassertion
Unit
Min
Typ
Max
4
8
15
ms
Output low voltage
IO = 5 mA
−
−
0.4
V
Off current
VOC = 2.7 V, 5.5 V
(No OC Condition)
−
−
1.0
µA
EN pin characteristics
(VI = 5.5 V, IO = rated current, TJ = 25°C, unless otherwise specified)
Value
Symbol
Parameter
Test condition
Unit
Min
Typ
Max
VI = 2.7 V to 5.5 V
2.0
−
−
V
VI = 4.5 V to 5.5 V
−
−
0.8
V
VI = 2.7 V to 4.5 V
−
−
0.4
V
Input current
VIENX = 0 V or VI
-0.5
−
0.5
uA
tON
Turn-ON time(1)
RL = 10 Ω
CL = 100 mF
−
−
5
ms
tOFF
Turn-OFF time (1)
RL = 10 Ω
CL = 100 mF
−
−
10
ms
VIH
High level input voltage
VIL
Low level input voltage
II
1. Not tested in production, specified by design
Doc ID 13793 Rev 4
15/34
Detail device characteristics
STMPS2141, STMPS2151, STMPS2161, STMPS2171
7
Detail device characteristics
7.1
STMPS2141, STMPS2151 additional electrical charts
The waveforms displayed in Section 7.1 are captured with the STMPS2141 device. The
STMPS2151 is expected to have the same characteristics with EN in the opposite polarity.
7.1.1
Turn on/off characteristics at VOUT = 5.0 V
Figure 3.
Voltage output turn on delay time
Figure 4.
Voltage output turn off delay time
Figure 5.
Current output turn on delay time
Figure 6.
Current output turn off delay time
16/34
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Detail device characteristics
7.1.2
Turn on/off characteristics at VOUT = 3.0 V
Figure 7.
Voltage output turn on delay time
Figure 8.
Figure 9.
Current output turn on delay time
Figure 10. Current output turn off delay time
7.1.3
UVLO
Figure 11. UVLO rising
Voltage output turn off delay time
Figure 12. UVLO falling
Doc ID 13793 Rev 4
17/34
Detail device characteristics
7.1.4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
OC protection characteristics
Figure 13. OC protection at VOUT = 3.0 V
Figure 14. OC protection at VOUT = 3.0 V
Figure 15. OC protection at VOUT = 5.0 V
Figure 16. OC protection at VOUT = 5.0 V
7.1.5
Other electrical characteristics
Figure 17. ICC vs VIN (enabled)
18/34
Figure 18. ICC vs temperature (enabled)
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Detail device characteristics
Figure 19. ICC vs VIN (disabled)
Figure 20. ICC vs temperature (disabled)
Figure 21. RDS ON vs VIN
Figure 22. RDS ON vs temperature
Figure 23. ILIMIT vs temperature
Figure 24. Switch leakage vs temperature
Doc ID 13793 Rev 4
19/34
Detail device characteristics
Figure 25. Output rise time vs. VIN
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Figure 26. Output fall time vs. VIN
Figure 27. UVLO vs temperature
20/34
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
7.2
Detail device characteristics
STMPS2161, STMPS2171 electrical charts
The waveforms displayed in Section 7.2 are captured with the STMPS2161 device. The
STMPS2171 is expected to have the same characteristics with EN in the opposite polarity.
7.2.1
Turn on/off characteristics at VOUT = 5.0 V
Figure 28. Voltage output turn on delay time
Figure 29. Voltage output turn off delay time
Figure 30. Current output turn on delay time
Figure 31. Current output turn off delay time
Doc ID 13793 Rev 4
21/34
Detail device characteristics
7.2.2
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Turn on/off characteristics at VOUT = 3.0 V
Figure 32. Voltage output turn on delay time
Figure 33. Voltage output turn off delay time
Figure 34. Current output turn on delay time
Figure 35. Current output turn off delay time
7.2.3
UVLO
Figure 36. UVLO rising
22/34
Figure 37. UVLO falling
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
7.2.4
Detail device characteristics
OC protection characteristics
Figure 38. OC protection at VOUT = 3.0 V
Figure 39. OC protection at VOUT = 3.0 V
Figure 40. OC protection at VOUT = 5.0 V
Figure 41. OC protection at VOUT = 5.0 V
Doc ID 13793 Rev 4
23/34
Detail device characteristics
7.2.5
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Other electrical characteristics
Figure 42. ICC vs VIN (enabled)
Figure 43. ICC vs temperature (enabled)
Figure 44. ICC vs VIN (disabled)
Figure 45. ICC vs temperature (disabled)
Figure 46. RDS ON vs VIN
Figure 47. RDS ON vs temperature
24/34
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Detail device characteristics
Figure 48. ILIMIT vs temperature
Figure 49. Switch leakage vs temperature
Figure 50. Output rise time vs. VIN
Figure 51. Output fall time vs. VIN
Figure 52. UVLO vs temperature
Doc ID 13793 Rev 4
25/34
Package mechanical data
8
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Figure 53. SOT23-5L package outline
.
Table 17.
SOT23-5L mechanical data
Millimeters
Inches
Symbol.
Min
Typ
Max
Min
Typ
Max
0.90
−
1.45
35.4
−
57.1
−
−
−
−
−
−
A1
0.00
−
0.10
0.0
−
3.9
A2
0.90
−
1.30
35.4
−
51.2
b
0.35
−
0.50
13.7
−
19.7
C
0.09
−
0.20
3.5
−
7.8
D
2.80
−
3.00
110.2
−
118.1
E
1.50
−
1.75
59.0
−
68.8
e
−
0.95
−
−
37.4
−
H
2.60
−
3.00
102.3
−
118.1
L
0.10
−
0.60
3.9
−
23.6
A
26/34
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Package mechanical data
Figure 54. SOT23-5L footprint recommendations
Table 18.
SOT23-5L footprint dimensions
Footprint data
Symbol
Millimeters
Inches
A
3.50
0.138
B
1.10
0.043
C
0.60
0.024
D
0.95
0.037
E
1.20
0.047
F
2.30
0.090
Figure 55. SOT23-5L carrier tape
Doc ID 13793 Rev 4
27/34
Package mechanical data
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Figure 56. SOT23-5L reel information
28/34
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Package mechanical data
Figure 57. SO-8 package outline
0016023 C
1. Drawing not to scale
Table 19.
SO-8 mechanical data
millimeters
inches
Symbol
Min
Typ
Max
Min
Typ
Max
1.35
−
1.75
0.053
−
0.069
−
−
−
−
−
−
A1
0.10
−
0.25
0.004
−
0.010
A2
1.10
−
1.65
0.043
−
0.065
B
0.33
−
0.51
0.013
−
0.020
C
0.19
−
0.25
0.007
−
0.010
D (1)
4.80
−
5.00
0.189
−
0.197
E
3.80
−
4.00
0.15
−
0.157
e
−
1.27
−
−
0.050
−
H
5.80
−
6.20
0.228
−
0.244
h
0.25
−
0.50
0.010
−
0.020
L
0.40
−
1.27
0.016
−
0.050
−
0.004
A
k
ddd
0° (min.), 8° (max.)
−
−
0.10
−
1. Dimension D does not include mold flash, protrusions or gate burrs. Mold flash, potrusions or gate burrs
shall not exceed 0.15mm (.006inch) in total (both sides).
Doc ID 13793 Rev 4
29/34
Package mechanical data
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Figure 58. MSOP8 package outline
D
8
5
c
E1
1
E
4
k
A1
A
L
L2
A2
L1
ccc
b
e
POA 7113595
1. Drawing not to scale.
Table 20.
MSOP8 package mechanical data
Millimeters
Inches
Symbol
Min
Typ
Max
Min
Typ
Max
A
−
−
1.10
−
−
0.043
A1
0.05
−
0.15
0.002
0.004
0.006
A2
0.75
0.85
0.95
0.031
0.034
0.037
b
0.25
−
0.40
0.010
0.013
0.016
c
0.13
−
0.23
0.005
0.007
0.009
D
2.90
3.00
3.10
0.114
0.118
0.122
E
4.65
4.90
5.15
0.187
0.193
0.199
E1
2.90
3.00
3.10
0.114
0.118
0.122
e
−
0.65
−
−
0.026
−
L
0.40
0.55
0.70
0.016
0.022
0.028
L1
−
0.95
−
−
0.037
K
0°
−
6°
0°
−
ccc
30/34
0.10
Doc ID 13793 Rev 4
6°
0.004
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Package mechanical data
Figure 59. SO-8 carrier tape
Figure 60. MSOP8 carrier tape
?"
Doc ID 13793 Rev 4
31/34
Package mechanical data
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Figure 61. Reel information
Table 21.
Reel mechanical data
Millimeters
Symbol
32/34
Min
Typ
Max
A
−
−
330
C
12.8
−
13.2
D
20.2
−
−
N
60
−
−
T
−
v
22.4
Doc ID 13793 Rev 4
STMPS2141, STMPS2151, STMPS2161, STMPS2171
9
Revision history
Revision history
Table 22.
Document revision history
Date
Revision
Changes
01-Aug-2007
1
Initial release.
18-Dec-2007
2
Minor text changes, updated Figure 53 on page 26, added Section 7:
Detail device characteristics on page 16.
24-Jan-2008
3
Footnote added in Table 1 on page 1, replaced Figure 58 on page 30
and Table 20 on page 30, TSSOP8 package name replaced with
MSOP8.
17-Jul-2009
4
Updated Chapter 3, test conditions modified for Ireverse in Table 12 on
page 14 and Chapter 7.
Added: Figure 55, Figure 56, Figure 59, Figure 60 and Figure 61.
Doc ID 13793 Rev 4
33/34
STMPS2141, STMPS2151, STMPS2161, STMPS2171
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2009 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
34/34
Doc ID 13793 Rev 4