BITECH 5711

MODEL SERIES 5710
3” Diameter
Single Turn
Wirewound
2
Precision Potentiometer
MODEL STYLES
5711
5713
1/4" Shaft, 1/2" Bushing
1/4" Shaft, Servo
ELECTRICAL
Resistance Range, Ohms
Standard Resistance Tolerance
Minimum Practical Resistance Tolerance
Independent Linearity
Minimum Practical Independent Linearity
25 to 145K
±5%
±1%
±0.5%
±0.5%, <75 Ohms
±0.25%, 75-249 Ohms
±0.15%, 250-6,999 Ohms
±0.075%, ≥7K Ohms
5.0 at 40°C derating to 0 at 105°C
1,000V rms
1,000 Megohms
100 Ohms
358° ±1°
±1°
Within Std. Linearity Tolerance
Power Rating, Watts
Dielectric Strength
Insulation Resistance, Minimum
Noise, Maximum
Actual Electrical Travel
Tap Tolerance
End Voltage, Maximum
ENVIRONMENTAL (MIL-R-12934)
Operating Temperature Range
Static: –65°C to +105°C
Dynamic: -40°C to +125°C
5 cycles, –65°C to +105°C
100G’s
5G’s, 10 to 500 Hz
Ten 24 hour cycles
1,000 hours at 105°C
1 Mil. Shaft Rev.
1 mil. shaft rev. plus 900 hrs. at rated wattage at 40°C
Temperature Cycling
Shock, 6ms Half Sine
Vibration
Moisture
High Temperature Exposure
Rotational Life
Rotational Load Life
Specifications subject to change without notice.
2-55
Model 5710 Series
MECHANICAL
Total Mechanical Travel
Number of Cups, Maximum
Weight, Nominal
360° Continuous
4
5.8 oz. Single Cup
1.3 oz. Each Added Cup
1°
.005”
5711
5713
.0005”
.001”
.002”
.0015”
.004”
.101”
.004”
.002”
1.5 oz.-in.
1.3 oz.-in.
1.2 oz.-in.
0.7 oz.-in.
Backlash, Maximum
Shaft End Play, Maximum
Shaft Runout, T.I.R., Maximum
Pilot Diameter Runout, T.I.R., Maximum
Lateral Runout, T.I.R., Maximum
Shaft Radial Play, Maximum
Starting Torque, Maximum
Running Torque, Maximum
STANDARD RESISTANCE VALUES, OHMS
Total
Resistance
Theoretical
Resolution
(% Nominal)
Tempco
of Wire
1K
2K
5K
10K
20K
50K
100K
0.062
0.050
0.038
0.031
0.027
0.024
0.022
±130 ppm/°C
±130 ppm/°C
±130 ppm/°C
±130 ppm/°C
±130 ppm/°C
± 20 ppm/°C
± 20 ppm/°C
METRIC CONVERSIONS
1 in.
1 oz.
25.4 mm
28.4 gm
2-56
1 oz.-in.
1 lb.-in.
0,007 N-m
0,113 N-m
Model 5710 Series
OUTLINE DIMENSIONS (Inch/mm)
Model 5711 - Bushing Mount
1.482±.031
37.64± 0.79
“RS”
Mounting Surface
.982±.020
24.9± 0.51
“L”
.469 Min.
11.9
Dimensions shown are with
1 cup, for each additional cup:
increase “RS” by .562
14.3
.562±.002
increase “L” by
14.3± 0.05
Clamp CW
Ears
.2497 + .0000
– .0003
Dia.
6.342 + 0.000
– 0.008
1.500±.031
38.10± 0.79
90˚ Max.
1.750
R. Max.
44.45
1.375±.016
Dia.
34.93± 0.41
3.000± .016 Dia.
76.20± 0.41
+
+
.5937 + .0000
– .0020
Dia.
15.08 + 0.000
– 0.051
Chamfer
.016 Max. x 45
˚
0.41
.062 + .000
– .010
1.58 + 0.00
– 0.25
Slider
CCW
Locating Hole
.129 ± .005 Dia. x .062± .016 Deep
1.58 ± 0.41
3.28± 0.13
Positioned as shown ± 5˚
.531± .016
13.5± 0.41
1/2-32 NS Thread
.500±.016
12.7± 0.41
OUTLINE DIMENSIONS (Inch/mm)
Model 5713 - Servo Mount
1.520±.031
38.61± 0.79
“RS”
1.020±.015
25.91± 0.38
“L”
.500
12.7
Min.
3.000± .016 Dia.
76.20± 0.41
Mounting Surface
.625±.031
15.9± 0.79
Dimensions shown are with
1 cup, for each additional cup:
increase “RS” by .562
14.3
.562±.002
increase “L” by
14.3± 0.05
2.785
73.03 Dia. Max.
.073 Min.
1.85
Clamp CW
Ears
.2497 + .0000
– .0003
Dia.
6.342 + 0.000
– 0.008
Chamfer
.016 Max. x 45
˚
0.41
90˚ Max.
Slider
CCW
1.750
R. Max.
44.45
3.000±.005 Dia.
76.20± 0.13
2.875 + .000
– .001
Dia.
73.03 + 0.00
– 0.03
+
.093± .005
2.36 ± 0.13
.062± .005
1.58± 0.13
2-57
Model 5710 Series
2
SPECIAL FEATURES
Center Tap
Linearity Tape
Rear Shaft Extension
Flatted Shaft
Slotted Shaft
Anti-Fungus Treatment
CT
LT
RS
FS
SS
AF
ORDERING INFORMATION
5711 R 10K L.50 XX
Optional Special
Feature Code
Model Series
Resistance Prefix
Linearity
Resistance Value
CIRCUIT DIAGRAM
NOTES
Metric equivalents, based on 1 inch = 25.4mm are rounded to
the same number of significant figures as in the original
English units and are provided for general information only.
(S)
(CCW)
INCH
mm
Tolerances unless otherwise specified:
Linear = ± .01 inches
(.25mm)
Angular = ± 2 degrees
(CW)
2-58
Model 5710 Series