FREESCALE MPC8347

Freescale Semiconductor
MPC8347EAEC
Rev. 3, 11/2006
Technical Data
MPC8347EA PowerQUICC™ II Pro
Integrated Host Processor Hardware
Specifications
The MPC8347EA contains a PowerPC™ processor core
(built on Power Architecture™ technology) with system
logic for networking, storage, and general-purpose
embedded applications. For functional characteristics of the
processor, refer to the MPC8349EA PowerQUICC™ II Pro
Integrated Host Processor Reference Manual, Rev. 0.
To locate published errata or updates for this document,
contact your Freescale sales office.
NOTE
The information in this document is accurate
for revision 3.x silicon and later (in other
words, for devices with part numbers ending
in A or B, such as the MPC8347EA or
MPC8347EB). For information on revision
1.1 silicon and earlier versions
(MPC8347E/MPC8347), see the
PowerQUICC™ II Pro Integrated Host
Processor Hardware Specifications.
See Section 23.1, “Part Numbers Fully
Addressed by this Document,” for silicon
revision level determination.
© Freescale Semiconductor, Inc., 2005, 2006. All rights reserved.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
17.
18.
19.
20.
21.
22.
23.
Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . 7
Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 11
Clock Input Timing . . . . . . . . . . . . . . . . . . . . . . . . . . 13
RESET Initialization . . . . . . . . . . . . . . . . . . . . . . . . . 14
DDR and DDR2 SDRAM . . . . . . . . . . . . . . . . . . . . . 16
DUART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Ethernet: Three-Speed Ethernet, MII Management . 24
USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Local Bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
JTAG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
I2C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
PCI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Package and Pin Listings . . . . . . . . . . . . . . . . . . . . . 59
Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Thermal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
System Design Information . . . . . . . . . . . . . . . . . . . 99
Document Revision History . . . . . . . . . . . . . . . . . . 104
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . 104
Overview
1
Overview
This section provides a high-level overview of the MPC8347EA features. Figure 1 shows the major
functional units within the MPC8347EA.
Security
DUART
Dual I2C
Timers
GPIO
High-Speed
USB 2.0
Dual
Role
e300 Core
Interrupt
Controller
10/100/1000
Ethernet
32KB
D-Cache
10/100/1000
Ethernet
32KB
I-Cache
Local Bus
PCI
SEQ
DDR
SDRAM
Controller
DMA
Host
Figure 1. MPC8347EA Block Diagram
Major features of the MPC8347EA are as follows:
• Embedded PowerPC e300 processor core; operates at up to 667 MHz
— High-performance, superscalar processor core
— Floating-point, integer, load/store, system register, and branch processing units
— 32-Kbyte instruction cache, 32-Kbyte data cache
— Lockable portion of L1 cache
— Dynamic power management
— Software-compatible with the other Freescale processor families that implement the PowerPC
architecture
• Double data rate, DDR1/DDR2 SDRAM memory controller
— Programmable timing supporting DDR1 and DDR2 SDRAM
— 32- or 64-bit data interface, up to 400 MHz data rate for TBGA, 266 MHz for PBGA
— Up to four physical banks (chip selects), each bank up to 1 Gbyte independently addressable
— DRAM chip configurations from 64 Mbits to 1 Gbit with x8/x16 data ports
— Full error checking and correction (ECC) support
— Support for up to 16 simultaneous open pages (up to 32 pages for DDR2)
— Contiguous or discontiguous memory mapping
— Read-modify-write support
— Sleep-mode support for SDRAM self refresh
— Auto refresh
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
2
Freescale Semiconductor
Overview
•
•
•
— On-the-fly power management using CKE
— Registered DIMM support
— 2.5-V SSTL2 compatible I/O for DDR1, 1.8-V SSTL2 compatible I/O for DDR2
Dual three-speed (10/100/1000) Ethernet controllers (TSECs)
— Dual controllers designed to comply with IEEE Std. 802.3™, 802.3u, 820.3x, 802.3z, 802.3ac
— Ethernet physical interfaces:
– 1000 Mbps IEEE Std. 802.3 GMII/RGMII, IEEE Std. 802.3z TBI/RTBI, full-duplex
– 10/100 Mbps IEEE Std. 802.3 MII full- and half-duplex
— Buffer descriptors are backward-compatible with MPC8260 and MPC860T 10/100
programming models
— 9.6-Kbyte jumbo frame support
— RMON statistics support
— Internal 2-Kbyte transmit and 2-Kbyte receive FIFOs per TSEC module
— MII management interface for control and status
— Programmable CRC generation and checking
PCI interface
— Designed to comply with PCI specification revision 2.3
— Data bus width:
– 32-bit data PCI interface operating at up to 66 MHz
— PCI 3.3-V compatible
— PCI host bridge capabilities
— PCI agent mode on PCI interface
— PCI-to-memory and memory-to-PCI streaming
— Memory prefetching of PCI read accesses and support for delayed read transactions
— Posting of processor-to-PCI and PCI-to-memory writes
— On-chip arbitration supporting five masters on PCI
— Accesses to all PCI address spaces
— Parity supported
— Selectable hardware-enforced coherency
— Address translation units for address mapping between host and peripheral
— Dual address cycle for target
— Internal configuration registers accessible from PCI
Security engine is optimized to handle all the algorithms associated with IPSec, SSL/TLS, SRTP,
IEEE Std. 802.11i™, iSCSI, and IKE processing. The security engine contains four
crypto-channels, a controller, and a set of crypto execution units (EUs):
— Public key execution unit (PKEU) :
– RSA and Diffie-Hellman algorithms
– Programmable field size up to 2048 bits
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
3
Overview
•
•
– Elliptic curve cryptography
– F2m and F(p) modes
– Programmable field size up to 511 bits
— Data encryption standard (DES) execution unit (DEU)
– DES and 3DES algorithms
– Two key (K1, K2) or three key (K1, K2, K3) for 3DES
– ECB and CBC modes for both DES and 3DES
— Advanced encryption standard unit (AESU)
– Implements the Rijndael symmetric-key cipher
– Key lengths of 128, 192, and 256 bits
– ECB, CBC, CCM, and counter (CTR) modes
— XOR parity generation accelerator for RAID applications
— ARC four execution unit (AFEU)
– Stream cipher compatible with the RC4 algorithm
– 40- to 128-bit programmable key
— Message digest execution unit (MDEU)
– SHA with 160-, 224-, or 256-bit message digest
– MD5 with 128-bit message digest
– HMAC with either algorithm
— Random number generator (RNG)
— Four crypto-channels, each supporting multi-command descriptor chains
– Static and/or dynamic assignment of crypto-execution units through an integrated controller
– Buffer size of 256 bytes for each execution unit, with flow control for large data sizes
Universal serial bus (USB) dual role controller
— USB on-the-go mode with both device and host functionality
— Complies with USB specification Rev. 2.0
— Can operate as a stand-alone USB device
– One upstream facing port
– Six programmable USB endpoints
— Can operate as a stand-alone USB host controller
– USB root hub with one downstream-facing port
– Enhanced host controller interface (EHCI) compatible
– High-speed (480 Mbps), full-speed (12 Mbps), and low-speed (1.5 Mbps) operations
— External PHY with UTMI, serial and UTMI+ low-pin interface (ULPI)
Universal serial bus (USB) multi-port host controller
— Can operate as a stand-alone USB host controller
– USB root hub with one or two downstream-facing ports
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
4
Freescale Semiconductor
Overview
•
•
•
•
– Enhanced host controller interface (EHCI) compatible
– Complies with USB specification Rev. 2.0
— High-speed (480 Mbps), full-speed (12 Mbps), and low-speed (1.5 Mbps) operations
— Direct connection to a high-speed device without an external hub
— External PHY with serial and low-pin count (ULPI) interfaces
Local bus controller (LBC)
— Multiplexed 32-bit address and data operating at up to 133 MHz
— Eight chip selects for eight external slaves
— Up to eight-beat burst transfers
— 32-, 16-, and 8-bit port sizes controlled by an on-chip memory controller
— Three protocol engines on a per chip select basis:
– General-purpose chip select machine (GPCM)
– Three user-programmable machines (UPMs)
– Dedicated single data rate SDRAM controller
— Parity support
— Default boot ROM chip select with configurable bus width (8-, 16-, or 32-bit)
Programmable interrupt controller (PIC)
— Functional and programming compatibility with the MPC8260 interrupt controller
— Support for 8 external and 35 internal discrete interrupt sources
— Support for 1 external (optional) and 7 internal machine checkstop interrupt sources
— Programmable highest priority request
— Four groups of interrupts with programmable priority
— External and internal interrupts directed to host processor
— Redirects interrupts to external INTA pin in core disable mode.
— Unique vector number for each interrupt source
Dual industry-standard I2C interfaces
— Two-wire interface
— Multiple master support
— Master or slave I2C mode support
— On-chip digital filtering rejects spikes on the bus
— System initialization data optionally loaded from I2C-1 EPROM by boot sequencer embedded
hardware
DMA controller
— Four independent virtual channels
— Concurrent execution across multiple channels with programmable bandwidth control
— Handshaking (external control) signals for all channels: DMA_DREQ[0:3],
DMA_DACK[0:3], DMA_DDONE[0:3]
— All channels accessible to local core and remote PCI masters
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
5
Overview
•
•
•
•
•
•
— Misaligned transfer capability
— Data chaining and direct mode
— Interrupt on completed segment and chain
DUART
— Two 4-wire interfaces (RxD, TxD, RTS, CTS)
— Programming model compatible with the original 16450 UART and the PC16550D
Serial peripheral interface (SPI) for master or slave
General-purpose parallel I/O (GPIO)
— 52 parallel I/O pins multiplexed on various chip interfaces
System timers
— Periodic interrupt timer
— Real-time clock
— Software watchdog timer
— Eight general-purpose timers
Designed to comply with IEEE Std. 1149.1™, JTAG boundary scan
Integrated PCI bus and SDRAM clock generation
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
6
Freescale Semiconductor
Electrical Characteristics
2
Electrical Characteristics
This section provides the AC and DC electrical specifications and thermal charaistics for the
MPC8347EA. The MPC8347EA is currently targeted to these specifications. Some of these specifications
are independent of the I/O cell, but are included for a more complete reference. These are not purely I/O
buffer design specifications.
2.1
Overall DC Electrical Characteristics
This section covers the ratings, conditions, and other characteristics.
2.1.1
Absolute Maximum Ratings
Table 1 provides the absolute maximum ratings.
Table 1. Absolute Maximum Ratings 1
Characteristic
Symbol
Max Value
Unit
Core supply voltage
VDD
–0.3 to 1.32
V
PLL supply voltage
AVDD
–0.3 to 1.32
V
DDR and DDR2 DRAM I/O voltage
GVDD
–0.3 to 2.75
–0.3 to 1.98
V
Three-speed Ethernet I/O, MII management voltage
LVDD
–0.3 to 3.63
V
PCI, local bus, DUART, system control and power management, I2C,
and JTAG I/O voltage
OVDD
–0.3 to 3.63
V
Input voltage
MVIN
–0.3 to (GVDD + 0.3)
V
2, 5
MVREF
–0.3 to (GVDD + 0.3)
V
2, 5
Three-speed Ethernet signals
LVIN
–0.3 to (LVDD + 0.3)
V
4, 5
Local bus, DUART, CLKIN, system control and
power management, I2C, and JTAG signals
OVIN
–0.3 to (OVDD + 0.3)
V
3, 5
PCI
OVIN
–0.3 to (OVDD + 0.3)
V
6
TSTG
–55 to 150
•C
DDR DRAM signals
DDR DRAM reference
Storage temperature range
Notes
Notes:
1. Functional and tested operating conditions are given in Table 2. Absolute maximum ratings are stress ratings only, and
functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause
permanent damage to the device.
2. Caution: MVIN must not exceed GVDD by more than 0.3 V. This limit can be exceeded for a maximum of 20 ms during
power-on reset and power-down sequences.
3. Caution: OVIN must not exceed OVDD by more than 0.3 V. This limit can be exceeded for a maximum of 20 ms during
power-on reset and power-down sequences.
4. Caution: LVIN must not exceed LVDD by more than 0.3 V. This limit can be exceeded for a maximum of 20 ms during power-on
reset and power-down sequences.
5. (M,L,O)VIN and MVREF may overshoot/undershoot to a voltage and for a maximum duration as shown in Figure 2.
6. OVIN on the PCI interface can overshoot/undershoot according to the PCI Electrical Specification for 3.3-V operation, as
shown in Figure 3.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
7
Electrical Characteristics
2.1.2
Power Supply Voltage Specification
Table 2 provides the recommended operating conditions for the MPC8347EA. Note that the values in
Table 2 are the recommended and tested operating conditions. Proper device operation outside these
conditions is not guaranteed.
Table 2. Recommended Operating Conditions
Symbol
Recommended
Value
Unit
Notes
Core supply voltage
VDD
1.2 V ± 60 mV
V
1
PLL supply voltage
AVDD
1.2 V ± 60 mV
V
1
DDR and DDR2 DRAM I/O voltage
GVDD
2.5 V ± 125 mV
1.8 V ± 90 mV
V
Three-speed Ethernet I/O supply voltage
LVDD1
3.3 V ± 330 mV
2.5 V ± 125 mV
V
Three-speed Ethernet I/O supply voltage
LVDD2
3.3 V ± 330 mV
2.5 V ± 125 mV
V
PCI, local bus, DUART, system control and power
management, I2C, and JTAG I/O voltage
OVDD
3.3 V ± 330 mV
V
Characteristic
Notes:
1. GVDD, LVDD, OVDD, AVDD, and VDD must track each other and must vary in the same direction—either in the positive or
negative direction.
Figure 2 shows the undershoot and overshoot voltages at the interfaces of the MPC8347EA.
G/L/OVDD + 20%
G/L/OVDD + 5%
VIH
G/L/OVDD
GND
GND – 0.3 V
VIL
GND – 0.7 V
Not to Exceed 10%
of tinterface1
Note:
1. tinterface refers to the clock period associated with the bus clock interface.
Figure 2. Overshoot/Undershoot Voltage for GVDD/OVDD/LVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
8
Freescale Semiconductor
Electrical Characteristics
Figure 3 shows the undershoot and overshoot voltage of the PCI interface of the MPC8347EA for the
3.3-V signals, respectively.
11 ns
(Min)
+7.1 V
7.1 V p-to-p
(Min)
Overvoltage
Waveform
0V
4 ns
(Max)
4 ns
(Max)
62.5 ns
+3.6 V
7.1 V p-to-p
(Min)
Undervoltage
Waveform
–3.5 V
Figure 3. Maximum AC Waveforms on PCI interface for 3.3-V Signaling
2.1.3
Output Driver Characteristics
Table 3 provides information on the characteristics of the output driver strengths. The values are
preliminary estimates.
Table 3. Output Drive Capability
Output Impedance
(Ω)
Supply
Voltage
Local bus interface utilities signals
42
OVDD = 3.3 V
PCI signals (not including PCI output clocks)
25
PCI output clocks (including PCI_SYNC_OUT)
42
DDR signal
20
GVDD = 2.5 V
DDR2 signal
16
32 (half strength mode)
GVDD = 1.8 V
TSEC/10/100 signals
42
LVDD = 2.5/3.3 V
DUART, system control, I2C, JTAG
42
OVDD = 3.3 V
GPIO signals
42
OVDD = 3.3 V,
LVDD = 2.5/3.3 V
Driver Type
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
9
Electrical Characteristics
2.2
Power Sequencing
MPC8347EA does not require the core supply voltage and I/O supply voltages to be applied in any
particular order. Note that during the power ramp up, before the power supplies are stable, there may be a
period of time that I/O pins are actively driven. After the power is stable, as long as PORESET is asserted,
most I/O pins are tri-stated. To minimize the time that I/O pins are actively driven, it is recommended to
apply core voltage before I/O voltage and assert PORESET before the power supplies fully ramp up.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
10
Freescale Semiconductor
Power Characteristics
3
Power Characteristics
The estimated typical power dissipation for the MPC8347EA device is shown in Table 4.
Table 4. MPC8347EA Power Dissipation 1
Core
Frequency
(MHz)
CSB Frequency
(MHz)
Typical at TJ = 65
Typical 2, 3
Maximum 4
Unit
266
266
1.3
1.6
1.8
W
133
1.1
1.4
1.6
W
266
1.5
1.9
2.1
W
133
1.4
1.7
1.9
W
200
1.5
1.8
2.0
W
100
1.3
1.7
1.9
W
333
2.0
3.0
3.2
W
166
1.8
2.8
2.9
W
266
2.1
3.0
3.3
W
133
1.9
2.9
3.1
W
300
2.3
3.2
3.5
W
150
2.1
3.0
3.2
W
333
2.4
3.3
3.6
W
166
2.2
3.1
3.4
W
266
2.4
3.3
3.6
W
133
2.2
3.1
3.4
W
333
3.5
4.6
5
W
400
PBGA
400
333
400
450
TBGA
500
533
667
1
The values do not include I/O supply power (OVDD, LVDD, GVDD) or AVDD. For I/O power values, see Table 5.
Typical power is based on a voltage of Vdd = 1.2 V, a junction temperature of TJ = 105°C, and a Dhrystone benchmark
application.
3 Thermal solutions may need to design to a value higher than typical power based on the end application, T target, and I/O
A
power.
4 Maximum Power is based on a voltage of Vdd = 1.2 V, worst case process, a junction temperature of T = 105°C, and an
J
artificial smoke test.
2
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
11
Power Characteristics
Table 5 shows the estimated typical I/O power dissipation for MPC8347EA.
Table 5. MPC8347EA Typical I/O Power Dissipation
Parameter
DDR2
GVDD
(1.8 V)
DDR1
GVDD
(2.5 V)
OVDD
(3.3 V)
LVDD
(3.3 V)
LVDD
(2.5 V)
Unit
Comments
200 MHz, 32 bits
0.31
0.42
—
—
—
W
—
200 MHz, 64 bits
0.42
0.55
—
—
—
W
—
266 MHz, 32 bits
0.35
0.5
—
—
—
W
—
266 MHz, 64 bits
0.47
0.66
—
—
—
W
—
300 MHz 1, 32 bits
0.37
0.54
—
—
—
W
—
300 MHz1, 64 bits
0.50
0.7
—
—
—
W
—
333 MHz1, 32 bits
0.39
0.58
—
—
—
W
—
333 MHz1, 64 bits
0.53
0.76
—
—
—
W
—
400MHz1, 32b
0.44
—
—
—
—
—
400MHz1, 64b
0.59
—
—
—
—
—
33 MHz, 32 bits
—
—
0.04
—
—
W
—
66 MHz, 32 bits
—
—
0.07
—
—
W
—
167 Mhz, 32 bits
—
—
0.34
—
—
W
—
133 MHz, 32 bits
—
—
0.27
—
—
W
—
83 MHz, 32 bits
—
—
0.17
—
—
W
—
66 MHz, 32 bits
—
—
0.14
—
—
W
—
50 Mhz, 32 bits
—
—
0.11
—
—
W
—
MII
—
—
—
0.01
—
W
GMII or TBI
—
—
—
0.06
—
W
Multiply by
number of
interfaces used.
RGMII or RTBI
—
—
—
—
0.04
W
12 MHz
—
—
0.01
—
—
W
480 MHz
—
—
0.2
—
—
W
—
—
0.01
—
—
W
Interface
DDR I/O
65% utilization
2.5 V
Rs = 20 Ω
Rt = 50 Ω
2 pair of clocks
PCI I/O load = 30 pf
Local Bus I/O
Load = 25 pf
TSEC I/O
Load = 25 pf
USB
Other I/O
1
Multiply by 2 if
using 2 ports.
—
TBGA package only.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
12
Freescale Semiconductor
Clock Input Timing
4
Clock Input Timing
This section provides the clock input DC and AC electrical characteristics for the MPC8347EA.
4.1
DC Electrical Characteristics
Table 7 provides the clock input (CLKIN/PCI_SYNC_IN) DC timing specifications for the MPC8347EA.
Table 6. CLKIN DC Electrical Characteristics
Parameter
Condition
Symbol
Min
Max
Unit
Input high voltage
—
VIH
2.7
OVDD+0.3
V
Input low voltage
—
VIL
–0.3
0.4
V
0V ≤VIN ≤ OVDD
IIN
—
±10
μA
PCI_SYNC_IN Input current
0V ≤VIN ≤ 0.5 V or
OVDD – 0.5 V ≤VIN ≤ OVDD
IIN
—
±10
μA
PCI_SYNC_IN Input current
0.5 V ≤VIN ≤ OVDD - 0.5 V
IIN
—
±50
μA
CLKIN Input current
4.2
AC Electrical Characteristics
The primary clock source for the MPC8347EA can be one of two inputs, CLKIN or PCI_CLK, depending
on whether the device is configured in PCI host or PCI agent mode. Table 7 provides the clock input
(CLKIN/PCI_CLK) AC timing specifications for the MPC8347EA.
Table 7. CLKIN AC Timing Specifications
Parameter/Condition
Symbol
Min
Typical
Max
Unit
Notes
CLKIN/PCI_CLK frequency
fCLKIN
—
—
66
MHz
1
CLKIN/PCI_CLK cycle time
tCLKIN
15
—
—
ns
—
CLKIN/PCI_CLK rise and fall time
tKH, tKL
0.6
1.0
2.3
ns
2
tKHK/tCLKIN
40
—
60
%
3
—
—
—
+/– 150
ps
4, 5
CLKIN/PCI_CLK duty cycle
CLKIN/PCI_CLK jitter
Notes:
1. Caution: The system, core, USB, security, and TSEC must not exceed their respective maximum or minimum
operating frequencies.
2. Rise and fall times for CLKIN/PCI_CLK are measured at 0.4 V and 2.7 V.
3. Timing is guaranteed by design and characterization.
4. This represents the total input jitter—short term and long term—and is guaranteed by design.
5. The CLKIN/PCI_CLK driver’s closed loop jitter bandwidth should be <500 kHz at -20 dB. The bandwidth must be set
low to allow cascade-connected PLL-based devices to track CLKIN drivers with the specified jitter.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
13
RESET Initialization
5
RESET Initialization
This section describes the DC and AC electrical specifications for the reset initialization timing and
electrical requirements of the MPC8347EA.
5.1
RESET DC Electrical Characteristics
Table 8 provides the DC electrical characteristics for the RESET pins of the MPC8347EA.
Table 8. RESET Pins DC Electrical Characteristics
Characteristic
Symbol
Condition
Min
Max
Unit
Input high voltage
VIH
2.0
OVDD+0.3
V
Input low voltage
VIL
-0.3
0.8
V
Input current
IIN
±5
μA
Output high voltage
VOH
IOH = –8.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 8.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
Notes:
1. This table applies for pins PORESET, HRESET, SRESET and QUIESCE.
2. HRESET and SRESET are open drain pins, thus VOH is not relevant for those pins.
5.2
RESET AC Electrical Characteristics
Table 9 provides the reset initialization AC timing specifications of the MPC8347EA.
Table 9. RESET Initialization Timing Specifications
Parameter/Condition
Min
Max
Unit
Notes
Required assertion time of HRESET or SRESET (input) to
activate reset flow
32
—
tPCI_SYNC_IN
1
Required assertion time of PORESET with stable clock applied
to CLKIN when the MPC8347EA is in PCI host mode
32
—
tCLKIN
2
Required assertion time of PORESET with stable clock applied
to PCI_SYNC_IN when the MPC8347EA is in PCI agent mode
32
—
tPCI_SYNC_IN
1
HRESET/SRESET assertion (output)
512
—
tPCI_SYNC_IN
1
HRESET negation to SRESET negation (output)
16
—
tPCI_SYNC_IN
1
Input setup time for POR configuration signals
(CFG_RESET_SOURCE[0:2] and CFG_CLKIN_DIV) with
respect to negation of PORESET when the MPC8347EA is in
PCI host mode
4
—
tCLKIN
2
Input setup time for POR configuration signals
(CFG_RESET_SOURCE[0:2] and CFG_CLKIN_DIV) with
respect to negation of PORESET when the MPC8347EA is in
PCI agent mode
4
—
tPCI_SYNC_IN
1
MPC8347EA MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
14
Freescale Semiconductor
RESET Initialization
Table 9. RESET Initialization Timing Specifications (continued)
Input hold time for POR configuration signals with respect to
negation of HRESET
0
—
ns
Time for the MPC8347EA to turn off POR configuration signals
with respect to the assertion of HRESET
—
4
ns
3
Time for the MPC8347EA to turn on POR configuration signals
with respect to the negation of HRESET
1
—
tPCI_SYNC_IN
1, 3
Notes:
1. tPCI_SYNC_IN is the clock period of the input clock applied to PCI_SYNC_IN. In PCI host mode, the primary clock is applied
to the CLKIN input, and PCI_SYNC_IN period depends on the value of CFG_CLKIN_DIV. See the MPC8349EA Integrated
Host Processor Reference Manual.
2. tCLKIN is the clock period of the input clock applied to CLKIN. It is valid only in PCI host mode. See the MPC8349EA
Integrated Host Processor Reference Manual.
3. POR configuration signals consist of CFG_RESET_SOURCE[0:2] and CFG_CLKIN_DIV.
Table 10 lists the PLL and DLL lock times.
Table 10. PLL and DLL Lock Times
Parameter/Condition
Min
Max
Unit
PLL lock times
—
100
μs
DLL lock times
7680
122,880
csb_clk cycles
Notes
1, 2
Notes:
1. DLL lock times are a function of the ratio between the output clock and the coherency system bus clock (csb_clk). A 2:1 ratio
results in the minimum and an 8:1 ratio results in the maximum.
2. The csb_clk is determined by the CLKIN and system PLL ratio. See Section 19, “Clocking.”
MPC8347EA MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
15
DDR and DDR2 SDRAM
6
DDR and DDR2 SDRAM
This section describes the DC and AC electrical specifications for the DDR SDRAM interface of the
MPC8347EA. Note that DDR SDRAM is GVDD(typ) = 2.5 V and DDR2 SDRAM is GVDD(typ) = 1.8 V.
The AC electrical specifications are the same for DDR and DRR2 SDRAM.
NOTE
The information in this document is accurate for revision 3.0 silicon and later. For
information on revision 1.1 silicon and earlier versions see the MPC8347E
PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications. See
Section 23.1, “Part Numbers Fully Addressed by this Document,” for silicon revision level
determination.
6.1
DDR and DDR2 SDRAM DC Electrical Characteristics
Table 11 provides the recommended operating conditions for the DDR2 SDRAM component(s) of the
MPC8347EA when GVDD(typ) = 1.8 V.
Table 11. DDR2 SDRAM DC Electrical Characteristics for GVDD(typ) = 1.8 V
Parameter/Condition
Symbol
Min
Max
Unit
Notes
I/O supply voltage
GVDD
1.71
1.89
V
1
I/O reference voltage
MVREF
0.49 × GVDD
0.51 × GVDD
V
2
I/O termination voltage
VTT
MVREF – 0.04
MVREF + 0.04
V
3
Input high voltage
VIH
MVREF+ 0.125
GVDD + 0.3
V
Input low voltage
VIL
–0.3
MVREF – 0.125
V
Output leakage current
IOZ
–9.9
9.9
μA
Output high current (VOUT = 1.420 V)
IOH
–13.4
—
mA
Output low current (VOUT = 0.280 V)
IOL
13.4
—
mA
4
Notes:
1. GVDD is expected to be within 50 mV of the DRAM GVDD at all times.
2. MVREF is expected to equal 0.5 × GVDD, and to track GVDD DC variations as measured at the receiver. Peak-to-peak noise
on MVREF cannot exceed ±2% of the DC value.
3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to equal
MVREF. This rail should track variations in the DC level of MVREF.
4. Output leakage is measured with all outputs disabled, 0 V ≤ VOUT ≤ GVDD.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
16
Freescale Semiconductor
DDR and DDR2 SDRAM
Table 12 provides the DDR2 capacitance when GVDD(typ) = 1.8 V.
Table 12. DDR2 SDRAM Capacitance for GVDD(typ)=1.8 V
Parameter/Condition
Symbol
Min
Max
Unit
Notes
Input/output capacitance: DQ, DQS, DQS
CIO
6
8
pF
1
Delta input/output capacitance: DQ, DQS, DQS
CDIO
—
0.5
pF
1
Note:
1. This parameter is sampled. GVDD = 1.8 V ± 0.090 V, f = 1 MHz, TA = 25°C, VOUT = GVDD/2, VOUT (peak-to-peak) = 0.2 V.
Table 13 provides the recommended operating conditions for the DDR SDRAM component(s) when
GVDD(typ) = 2.5 V.
Table 13. DDR SDRAM DC Electrical Characteristics for GVDD (typ) = 2.5 V
Parameter/Condition
Symbol
Min
Max
Unit
Notes
I/O supply voltage
GVDD
2.375
2.625
V
1
I/O reference voltage
MVREF
0.49 × GVDD
0.51 × GVDD
V
2
I/O termination voltage
VTT
MVREF – 0.04
MVREF + 0.04
V
3
Input high voltage
VIH
MVREF + 0.18
GVDD + 0.3
V
Input low voltage
VIL
–0.3
MVREF– 0.18
V
Output leakage current
IOZ
–9.9
–9.9
μA
Output high current (VOUT = 1.95 V)
IOH
–15.2
—
mA
Output low current (VOUT = 0.35 V)
IOL
15.2
—
mA
4
Notes:
1. GVDD is expected to be within 50 mV of the DRAM GVDD at all times.
2. MVREF is expected to be equal to 0.5 × GVDD, and to track GVDD DC variations as measured at the receiver. Peak-to-peak
noise on MVREF may not exceed ±2% of the DC value.
3. VTT is not applied directly to the device. It is the supply to which far end signal termination is made and is expected to be
equal to MVREF. This rail should track variations in the DC level of MVREF.
4. Output leakage is measured with all outputs disabled, 0 V ≤ VOUT ≤ GVDD.
Table 14 provides the DDR capacitance when GVDD (typ)=2.5 V.
Table 14. DDR SDRAM Capacitance for GVDD (typ) = 2.5 V
Parameter/Condition
Symbol
Min
Max
Unit
Notes
Input/output capacitance: DQ, DQS
CIO
6
8
pF
1
Delta input/output capacitance: DQ, DQS
CDIO
—
0.5
pF
1
Note:
1. This parameter is sampled. GVDD = 2.5 V ± 0.125 V, f = 1 MHz, TA = 25°C, VOUT = GVDD/2, VOUT (peak-to-peak) = 0.2 V.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
17
DDR and DDR2 SDRAM
Table 15 provides the current draw characteristics for MVREF.
Table 15. Current Draw Characteristics for MVREF
Parameter / Condition
Current draw for MVREF
Symbol
Min
Max
Unit
Note
IMVREF
—
500
μA
1
1. The voltage regulator for MVREF must supply up to 500 μA current.
6.2
DDR and DDR2 SDRAM AC Electrical Characteristics
This section provides the AC electrical characteristics for the DDR and DDR2 SDRAM interface.
6.2.1
DDR and DDR2 SDRAM Input AC Timing Specifications
Table 16 provides the input AC timing specifications for the DDR2 SDRAM when GVDD(typ)=1.8 V.
Table 16. DDR2 SDRAM Input AC Timing Specifications for 1.8-V Interface
At recommended operating conditions with GVDD of 1.8 ± 5%.
Parameter
Symbol
Min
Max
Unit
AC input low voltage
VIL
—
MVREF – 0.25
V
AC input high voltage
VIH
MVREF + 0.25
—
V
Notes
Table 17 provides the input AC timing specifications for the DDR SDRAM when GVDD(typ)=2.5 V.
Table 17. DDR SDRAM Input AC Timing Specifications for 2.5-V Interface
At recommended operating conditions with GVDD of 2.5 ± 5%.
Parameter
Symbol
Min
Max
Unit
AC input low voltage
VIL
—
MVREF – 0.31
V
AC input high voltage
VIH
MVREF + 0.31
—
V
Notes
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
18
Freescale Semiconductor
DDR and DDR2 SDRAM
Table 18 provides the input AC timing specifications for the DDR SDRAM interface.
Table 18. DDR and DDR2 SDRAM Input AC Timing Specifications
At recommended operating conditions with GVDD of (1.8 V or 2.5 V) ± 5%.
Parameter
Symbol
Controller Skew for
MDQS—MDQ/MECC/MDM
Min
Max
tCISKEW
Unit
Notes
ps
1
400 MHz
–600
600
2
333 MHz
–750
750
3
266 MHz
–750
750
3
200 MHz
–750
750
3
Note:
1. tCISKEW represents the total amount of skew consumed by the controller between MDQS[n] and any corresponding
bit that will be captured with MDQS[n]. This should be subtracted from the total timing budget.
2. This specification applies only to the DDR2 interface.
3. This specification applies only to the DDR interface.
6.2.2
DDR and DDR2 SDRAM Output AC Timing Specifications
Table 19 shows the DDR and DDR2 output AC timing specifications.
Table 19. DDR and DDR2 SDRAM Output AC Timing Specifications
At recommended operating conditions with GVDD of (1.8 V or 2.5 V) ± 5%.
Parameter
MCK[n] cycle time, (MCK[n]/MCK[n] crossing)
ADDR/CMD/MODT output setup with respect to MCK
Symbol 1
Min
Max
Unit
Notes
tMCK
5
10
ns
2
ns
3
ns
3
ns
3
tDDKHAS
400 MHz
1.95
—
333 MHz
2.40
—
266 MHz
3.15
—
200 MHz
4.20
—
ADDR/CMD/MODT output hold with respect to MCK
tDDKHAX
400 MHz
1.95
—
333 MHz
2.40
—
266 MHz
3.15
—
200 MHz
4.20
—
MCS(n) output setup with respect to MCK
tDDKHCS
400 MHz
1.95
—
333 MHz
2.40
—
266 MHz
3.15
—
200 MHz
4.20
—
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
19
DDR and DDR2 SDRAM
Table 19. DDR and DDR2 SDRAM Output AC Timing Specifications (continued)
At recommended operating conditions with GVDD of (1.8 V or 2.5 V) ± 5%.
Symbol 1
Parameter
MCS(n) output hold with respect to MCK
Max
tDDKHCX
400 MHz
1.95
—
333 MHz
2.40
—
266 MHz
3.15
—
200 MHz
4.20
—
–0.6
0.6
MCK to MDQS Skew
tDDKHMH
MDQ/MECC/MDM output setup with respect to MDQS
tDDKHDS,
tDDKLDS
400 MHz
700
—
333 MHz
900
—
266 MHz
1100
—
200 MHz
1200
—
MDQ/MECC/MDM output hold with respect to MDQS
MDQS preamble start
Min
tDDKHDX,
tDDKLDX
400 MHz
700
—
333 MHz
900
—
266 MHz
1100
—
200 MHz
1200
—
–0.5 × tMCK – 0.6
–0.5 × tMCK
+0.6
tDDKHMP
Unit
Notes
ns
3
ns
4
ps
5
ps
5
ns
6
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
20
Freescale Semiconductor
DDR and DDR2 SDRAM
Table 19. DDR and DDR2 SDRAM Output AC Timing Specifications (continued)
At recommended operating conditions with GVDD of (1.8 V or 2.5 V) ± 5%.
Parameter
MDQS epilogue end
Symbol 1
Min
Max
Unit
Notes
tDDKHME
–0.6
0.6
ns
6
Note:
1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. Output hold time can be read as DDR timing (DD) from
the rising or falling edge of the reference clock (KH or KL) until the output goes invalid (AX or DX). For example, tDDKHAS
symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes from the high (H) state until outputs (A) are
set up (S) or output valid time. Also, tDDKLDX symbolizes DDR timing (DD) for the time tMCK memory clock reference (K) goes
low (L) until data outputs (D) are invalid (X) or data output hold time.
2. All MCK/MCK referenced measurements are made from the crossing of the two signals ±0.1 V.
3. ADDR/CMD includes all DDR SDRAM output signals except MCK/MCK, MCS, and MDQ/MECC/MDM/MDQS. For the
ADDR/CMD setup and hold specifications, it is assumed that the clock control register is set to adjust the memory clocks by
1/2 applied cycle.
4. tDDKHMH follows the symbol conventions described in note 1. For example, tDDKHMH describes the DDR timing (DD) from the
rising edge of the MCK(n) clock (KH) until the MDQS signal is valid (MH). tDDKHMH can be modified through control of the
DQSS override bits in the TIMING_CFG_2 registerand is typically set to the same delay as the clock adjust in the CLK_CNTL
register. The timing parameters listed in the table assume that these two parameters are set to the same adjustment value.
See the MPC8349EA PowerQUICC II Pro Integrated Processor Reference Manual for the timing modifications enabled by
use of these bits.
5. Determined by maximum possible skew between a data strobe (MDQS) and any corresponding bit of data (MDQ), ECC
(MECC), or data mask (MDM). The data strobe should be centered inside the data eye at the pins of the microprocessor.
6. All outputs are referenced to the rising edge of MCK(n) at the pins of the microprocessor. Note that tDDKHMP follows the
symbol conventions described in note 1.
Figure 4 shows the DDR SDRAM output timing for the MCK to MDQS skew measurement (tDDKHMH).
MCK[n]
MCK[n]
tMCK
tDDKHMHmax) = 0.6 ns
MDQS
tDDKHMH(min) = –0.6 ns
MDQS
Figure 4. Timing Diagram for tDDKHMH
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
21
DDR and DDR2 SDRAM
Figure 5 shows the DDR SDRAM output timing diagram.
MCK[n]
MCK[n]
tMCK
tDDKHAS ,tDDKHCS
tDDKHAX ,tDDKHCX
ADDR/CMD/MODT
Write A0
NOOP
tDDKHMP
tDDKHMH
MDQS[n]
tDDKHME
tDDKHDS
tDDKLDS
MDQ[x]
D0
D1
tDDKLDX
tDDKHDX
Figure 5. DDR SDRAM Output Timing Diagram
Figure 6 provides the AC test load for the DDR bus.
Output
Z0 = 50 Ω
RL = 50 Ω
GVDD/2
Figure 6. DDR AC Test Load
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
22
Freescale Semiconductor
DUART
7
DUART
This section describes the DC and AC electrical specifications for the DUART interface of the
MPC8347EA.
7.1
DUART DC Electrical Characteristics
Table 20 provides the DC electrical characteristics for the DUART interface of the MPC8347EA.
Table 20. DUART DC Electrical Characteristics
Parameter
Symbol
Min
Max
Unit
High-level input voltage
VIH
2
OVDD + 0.3
V
Low-level input voltage
VIL
–0.3
0.8
V
Input current
(0.8 V ≤VIN ≤ 2 V)
IIN
—
+/- 5
μA
High-level output voltage,
IOH = –100 μA
VOH
OVDD – 0.2
—
V
Low-level output voltage,
IOL = 100 μA
VOL
—
0.2
V
Note:
1. Note that the symbol VIN, in this case, represents the OVIN symbol referenced in Table 1
and Table 2.
7.2
DUART AC Electrical Specifications
Table 21 provides the AC timing parameters for the DUART interface of the MPC8347EA.
Table 21. DUART AC Timing Specifications
Parameter
Value
Unit
Minimum baud rate
256
baud
Maximum baud rate
> 1,000,000
baud
1
16
—
2
Oversample rate
Notes
Notes:
1. Actual attainable baud rate will be limited by the latency of interrupt processing.
2. The middle of a start bit is detected as the 8th sampled 0 after the 1-to-0 transition of the start bit. Subsequent bit
values are sampled each 16th sample.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
23
Ethernet: Three-Speed Ethernet, MII Management
8
Ethernet: Three-Speed Ethernet, MII Management
This section provides the AC and DC electrical characteristics for three-speeds (10/100/1000 Mbps) and
MII management.
8.1
Three-Speed Ethernet Controller (TSEC)
—GMII/MII/TBI/RGMII/RTBI Electrical Characteristics
The electrical characteristics specified here apply to the gigabit media independent interface (GMII), the
media independent interface (MII), ten-bit interface (TBI), reduced gigabit media independent
interface (RGMII), and reduced ten-bit interface (RTBI) signals except management data input/output
(MDIO) and management data clock (MDC). The MII, GMII, and TBI interfaces are defined for 3.3 V,
and the RGMII and RTBI interfaces can operate at 3.3 or 2.5 V. The RGMII and RTBI interfaces follow
the Hewlett-Packard Reduced Pin-Count Interface for Gigabit Ethernet Physical Layer Device
Specification, Version 1.2a (9/22/2000). The electrical characteristics for MDIO and MDC are specified
in Section 8.3, “Ethernet Management Interface Electrical Characteristics.”
8.1.1
TSEC DC Electrical Characteristics
All GMII, MII, TBI, RGMII, and RTBI drivers and receivers comply with the DC parametric attributes
specified in Table 22 and Table 23. The potential applied to the input of a GMII, MII, TBI, RGMII, or
RTBI receiver may exceed the potential of the receiver power supply (that is, a RGMII driver powered
from a 3.6 V supply driving VOH into a RGMII receiver powered from a 2.5-V supply). Tolerance for
dissimilar RGMII driver and receiver supply potentials is implicit in these specifications.The RGMII and
RTBI signals are based on a 2.5 V CMOS interface voltage as defined by JEDEC EIA/JESD8-5.
Table 22. GMII/TBI and MII DC Electrical Characteristics
Parameter
Symbol
Conditions
Min
Max
Unit
Supply voltage 3.3 V
LVDD 2
—
2.97
3.63
V
Output high voltage
VOH
IOH = –4.0 mA
LVDD = Min
2.40
LVDD + 0.3
V
Output low voltage
VOL
IOL = 4.0 mA
LVDD = Min
GND
0.50
V
Input high voltage
VIH
—
—
2.0
LVDD + 0.3
V
Input low voltage
VIL
—
—
–0.3
0.90
V
Input high current
IIH
—
40
μA
–600
—
μA
Input low current
IIL
VIN 1 = LVDD
1
VIN = GND
Note:
1. The symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2.
2. GMII/MII pins not needed for RGMII or RTBI operation are powered by the OVDD supply.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
24
Freescale Semiconductor
Ethernet: Three-Speed Ethernet, MII Management
Table 23. RGMII/RTBI (When Operating at 2.5 V), DC Electrical Characteristics
Parameters
Symbol
Conditions
Min
Max
Unit
Supply voltage 2.5 V
LVDD
—
2.37
2.63
V
Output high voltage
VOH
IOH = –1.0 mA
LVDD = Min
2.00
LVDD + 0.3
V
Output low voltage
VOL
IOL = 1.0 mA
LVDD = Min
GND – 0.3
0.40
V
Input high voltage
VIH
—
LVDD = Min
1.7
LVDD + 0.3
V
Input low voltage
VIL
—
LVDD =Min
–0.3
0.70
V
Input high current
IIH
VIN 1 = LVDD
—
10
μA
Input low current
IIL
VIN 1 = GND
–15
—
μA
Note:
1. The symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
25
Ethernet: Three-Speed Ethernet, MII Management
8.2
GMII, MII, TBI, RGMII, and RTBI AC Timing Specifications
The AC timing specifications for GMII, MII, TBI, RGMII, and RTBI are presented in this section.
8.2.1
GMII Timing Specifications
This section describes the GMII transmit and receive AC timing specifications.
8.2.1.1
GMII Transmit AC Timing Specifications
Table 24 provides the GMII transmit AC timing specifications.
Table 24. GMII Transmit AC Timing Specifications
At recommended operating conditions with LVDD / OVDD of 3.3 V ± 10%.
Symbol 1
Min
Typ
Max
Unit
tGTX
—
8.0
—
ns
tGTXH/tGTX
43.75
—
56.25
%
tGTKHDX
0.5
—
5.0
ns
GTX_CLK clock rise time, VIL(min) to VIH(max)
tGTXR
—
—
1.0
ns
GTX_CLK clock fall time, VIH(max) to VIL(min)
tGTXF
—
—
1.0
ns
—
8.0
—
ns
45
—
55
%
Parameter/Condition
GTX_CLK clock period
GTX_CLK duty cycle
GTX_CLK to GMII data TXD[7:0], TX_ER, TX_EN delay
GTX_CLK125 clock period
tG125
GTX_CLK125 reference clock duty cycle measured at LVDD/ 2
2
tG125H/tG125
Notes:
1. The symbols for timing specifications follow the pattern t(first two letters of functional block)(signal)(state) (reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tGTKHDV symbolizes GMII transmit
timing (GT) with respect to the tGTX clock reference (K) going to the high state (H) relative to the time date input signals
(D) reaching the valid state (V) to state or setup time. Also, tGTKHDX symbolizes GMII transmit timing (GT) with respect
to the tGTX clock reference (K) going to the high state (H) relative to the time date input signals (D) going invalid (X) or
hold time. In general, the clock reference symbol is based on three letters representing the clock of a particular function.
For example, the subscript of tGTX represents the GMII(G) transmit (TX) clock. For rise and fall times, the latter
convention is used with the appropriate letter: R (rise) or F (fall).
2. This symbol represents the external GTX_CLK125 signal and does not follow the original symbol naming convention.
Figure 7 shows the GMII transmit AC timing diagram.
tGTXR
tGTX
GTX_CLK
tGTXH
tGTXF
TXD[7:0]
TX_EN
TX_ER
tGTKHDX
Figure 7. GMII Transmit AC Timing Diagram
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
26
Freescale Semiconductor
Ethernet: Three-Speed Ethernet, MII Management
8.2.1.2
GMII Receive AC Timing Specifications
Table 25 provides the GMII receive AC timing specifications.
Table 25. GMII Receive AC Timing Specifications
At recommended operating conditions with LVDD / OVDD of 3.3 V ± 10%.
Symbol 1
Min
Typ
Max
Unit
tGRX
—
8.0
—
ns
tGRXH/tGRX
40
—
60
%
RXD[7:0], RX_DV, RX_ER setup time to RX_CLK
tGRDVKH
2.0
—
—
ns
RXD[7:0], RX_DV, RX_ER hold time to RX_CLK
tGRDXKH
0.5
—
—
ns
RX_CLK clock rise, VIL(min) to VIH(max)
tGRXR
—
—
1.0
ns
RX_CLK clock fall time, VIH(max) to VIL(min)
tGRXF
—
—
1.0
ns
Parameter/Condition
RX_CLK clock period
RX_CLK duty cycle
Note:
1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tGRDVKH symbolizes GMII receive timing
(GR) with respect to the time data input signals (D) reaching the valid state (V) relative to the tRX clock reference (K) going
to the high state (H) or setup time. Also, tGRDXKL symbolizes GMII receive timing (GR) with respect to the time data input
signals (D) went invalid (X) relative to the tGRX clock reference (K) going to the low (L) state or hold time. In general, the clock
reference symbol is based on three letters representing the clock of a particular function. For example, the subscript of tGRX
represents the GMII (G) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter:
R (rise) or F (fall).
Figure 8 shows the GMII receive AC timing diagram.
G
tGRXR
tGRX
RX_CLK
tGRXH
tGRXF
RXD[7:0]
RX_DV
RX_ER
tGRDXKH
tGRDVKH
Figure 8. GMII Receive AC Timing Diagram
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
27
Ethernet: Three-Speed Ethernet, MII Management
8.2.2
MII AC Timing Specifications
This section describes the MII transmit and receive AC timing specifications.
8.2.2.1
MII Transmit AC Timing Specifications
Table 26 provides the MII transmit AC timing specifications.
Table 26. MII Transmit AC Timing Specifications
At recommended operating conditions with LVDD / OVDD of 3.3 V ± 10%.
Symbol 1
Min
Typ
Max
Unit
TX_CLK clock period 10 Mbps
tMTX
—
400
—
ns
TX_CLK clock period 100 Mbps
tMTX
—
40
—
ns
tMTXH/tMTX
35
—
65
%
tMTKHDX
1
5
15
ns
TX_CLK data clock rise VIL(min) to VIH(max)
tMTXR
1.0
—
4.0
ns
TX_CLK data clock fall VIH(max) to VIL(min)
tMTXF
1.0
—
4.0
ns
Parameter/Condition
TX_CLK duty cycle
TX_CLK to MII data TXD[3:0], TX_ER, TX_EN delay
Note:
1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMTKHDX symbolizes MII transmit timing
(MT) for the time tMTX clock reference (K) going high (H) until data outputs (D) are invalid (X). In general, the clock reference
symbol is based on two to three letters representing the clock of a particular function. For example, the subscript of tMTX
represents the MII(M) transmit (TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R
(rise) or F (fall).
Figure 9 shows the MII transmit AC timing diagram.
tMTXR
tMTX
TX_CLK
tMTXH
tMTXF
TXD[3:0]
TX_EN
TX_ER
tMTKHDX
Figure 9. MII Transmit AC Timing Diagram
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
28
Freescale Semiconductor
Ethernet: Three-Speed Ethernet, MII Management
8.2.2.2
MII Receive AC Timing Specifications
Table 27 provides the MII receive AC timing specifications.
Table 27. MII Receive AC Timing Specifications
At recommended operating conditions with LVDD / OVDD of 3.3 V ± 10%.
Symbol 1
Min
Typ
Max
Unit
RX_CLK clock period 10 Mbps
tMRX
—
400
—
ns
RX_CLK clock period 100 Mbps
tMRX
—
40
—
ns
tMRXH/tMRX
35
—
65
%
RXD[3:0], RX_DV, RX_ER setup time to RX_CLK
tMRDVKH
10.0
—
—
ns
RXD[3:0], RX_DV, RX_ER hold time to RX_CLK
tMRDXKH
10.0
—
—
ns
RX_CLK clock rise VIL(min) to VIH(max)
tMRXR
1.0
—
4.0
ns
RX_CLK clock fall time VIH(max) to VIL(min)
tMRXF
1.0
—
4.0
ns
Parameter/Condition
RX_CLK duty cycle
Note:
1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tMRDVKH symbolizes MII receive timing
(MR) with respect to the time data input signals (D) reach the valid state (V) relative to the tMRX clock reference (K) going to
the high (H) state or setup time. Also, tMRDXKL symbolizes MII receive timing (GR) with respect to the time data input signals
(D) went invalid (X) relative to the tMRX clock reference (K) going to the low (L) state or hold time. In general, the clock
reference symbol is based on three letters representing the clock of a particular functionl. For example, the subscript of tMRX
represents the MII (M) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R
(rise) or F (fall).
Figure 10 provides the AC test load for TSEC.
Z0 = 50 Ω
Output
RL = 50 Ω
LVDD/2
Figure 10. TSEC AC Test Load
Figure 11 shows the MII receive AC timing diagram.
tMRXR
tMRX
RX_CLK
tMRXH
RXD[3:0]
RX_DV
RX_ER
tMRXF
Valid Data
tMRDVKH
tMRDXKH
Figure 11. MII Receive AC Timing Diagram
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
29
Ethernet: Three-Speed Ethernet, MII Management
8.2.3
TBI AC Timing Specifications
This section describes the TBI transmit and receive AC timing specifications.
8.2.3.1
TBI Transmit AC Timing Specifications
Table 28 provides the TBI transmit AC timing specifications.
Table 28. TBI Transmit AC Timing Specifications
At recommended operating conditions with LVDD / OVDD of 3.3 V ± 10%.
Symbol 1
Min
Typ
Max
Unit
tTTX
—
8.0
—
ns
tTTXH/tTTX
40
—
60
%
tTTKHDX
1.0
—
5.0
ns
GTX_CLK clock rise, VIL(min) to VIH(max)
tTTXR
—
—
1.0
ns
GTX_CLK clock fall time, VIH(max) to VIL(min)
tTTXF
—
—
1.0
ns
—
8.0
—
ns
45
—
55
ns
Parameter/Condition
GTX_CLK clock period
GTX_CLK duty cycle
GTX_CLK to TBI data TXD[7:0], TX_ER, TX_EN delay
GTX_CLK125 reference clock period
tG125
GTX_CLK125 reference clock duty cycle
2
tG125H/tG125
Notes:
1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state )(reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tTTKHDV symbolizes the TBI transmit
timing (TT) with respect to the time from tTTX (K) going high (H) until the referenced data signals (D) reach the valid state (V)
or setup time. Also, tTTKHDX symbolizes the TBI transmit timing (TT) with respect to the time from tTTX (K) going high (H) until
the referenced data signals (D) reach the invalid state (X) or hold time. In general, the clock reference symbol is based on
three letters representing the clock of a particular function. For example, the subscript of tTTX represents the TBI (T) transmit
(TX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall).
2. This symbol represents the external GTX_CLK125 and does not follow the original symbol naming convention
Figure 12 shows the TBI transmit AC timing diagram.
tTTXR
tTTX
GTX_CLK
tTTXH
tTTXF
TXD[7:0]
TX_EN
TX_ER
tTTKHDX
Figure 12. TBI Transmit AC Timing Diagram
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
30
Freescale Semiconductor
Ethernet: Three-Speed Ethernet, MII Management
8.2.3.2
TBI Receive AC Timing Specifications
Table 29 provides the TBI receive AC timing specifications.
Table 29. TBI Receive AC Timing Specifications
At recommended operating conditions with LVDD / OVDD of 3.3 V ± 10%.
Symbol 1
Parameter/Condition
PMA_RX_CLK clock period
Min
tTRX
Typ
Max
16.0
Unit
ns
PMA_RX_CLK skew
tSKTRX
7.5
—
8.5
ns
RX_CLK duty cycle
tTRXH/tTRX
40
—
60
%
RXD[7:0], RX_DV, RX_ER (RCG[9:0]) setup time to rising
PMA_RX_CLK
tTRDVKH 2
2.5
—
—
ns
RXD[7:0], RX_DV, RX_ER (RCG[9:0]) hold time to rising
PMA_RX_CLK
tTRDXKH 2
1.5
—
—
ns
RX_CLK clock rise time VIL(min) to VIH(max)
tTRXR
0.7
—
2.4
ns
RX_CLK clock fall time VIH(max) to VIL(min)
tTRXF
0.7
—
2.4
ns
Note:
1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tTRDVKH symbolizes TBI receive timing
(TR) with respect to the time data input signals (D) reach the valid state (V) relative to the tTRX clock reference (K) going to
the high (H) state or setup time. Also, tTRDXKH symbolizes TBI receive timing (TR) with respect to the time data input signals
(D) went invalid (X) relative to the tTRX clock reference (K) going to the high (H) state. In general, the clock reference symbol
is based on three letters representing the clock of a particular function. For example, the subscript of tTRX represents the TBI
(T) receive (RX) clock. For rise and fall times, the latter convention is used with the appropriate letter: R (rise) or F (fall). For
symbols representing skews, the subscript SK followed by the clock that is being skewed (TRX).
2. Setup and hold time of even numbered RCG are measured from the riding edge of PMA_RX_CLK1. Setup and hold times
of odd-numbered RCG are measured from the riding edge of PMA_RX_CLK0.
Figure 13 shows the TBI receive AC timing diagram.
tTRXR
tTRX
PMA_RX_CLK1
tTRXH
tTRXF
Even RCG
RCG[9:0]
Odd RCG
tTRDVKH
tTRDXKH
tSKTRX
PMA_RX_CLK0
tTRDXKH
tTRXH
tTRDVKH
Figure 13. TBI Receive AC Timing Diagram
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
31
Ethernet: Three-Speed Ethernet, MII Management
8.2.4
RGMII and RTBI AC Timing Specifications
Table 30 presents the RGMII and RTBI AC timing specifications.
Table 30. RGMII and RTBI AC Timing Specifications
At recommended operating conditions with LVDD of 2.5 V ± 5%.
Symbol 1
Min
Typ
Max
Unit
tSKRGT
-0.5
—
0.5
ns
tSKRGT
1.0
—
2.8
ns
tRGT
7.2
8.0
8.8
ns
tRGTH/tRGT
45
50
55
%
tRGTH/tRGT
40
50
60
%
Rise time (20%–80%)
tRGTR
—
—
0.75
ns
Fall time (20%–80%)
tRGTF
—
—
0.75
ns
6
—
8.0
—
ns
47
—
53
%
Parameter/Condition
Data to clock output skew (at transmitter)
Data to clock input skew (at receiver)
Clock cycle duration
2
3
Duty cycle for 1000Base-T
4, 5
Duty cycle for 10BASE-T and 100BASE-TX
GTX_CLK125 reference clock period
GTX_CLK125 reference clock duty cycle
3, 5
tG12
tG125H/tG125
Notes:
1. In general, the clock reference symbol for this section is based on the symbols RGT to represent RGMII and RTBI timing.
For example, the subscript of tRGT represents the TBI (T) receive (RX) clock. Also, the notation for rise (R) and fall (F) times
follows the clock symbol. For symbols representing skews, the subscript is SK followed by the clock being skewed (RGT).
2. This implies that PC board design requires clocks to be routed so that an additional trace delay of greater than 1.5 ns is added
to the associated clock signal.
3. For 10 and 100 Mbps, tRGT scales to 400 ns ± 40 ns and 40 ns ± 4 ns, respectively.
4. Duty cycle may be stretched/shrunk during speed changes or while transitioning to a received packet clock domains as long
as the minimum duty cycle is not violated and stretching occurs for no more than three tRGT of the lowest speed transitioned.
5. Duty cycle reference is LVdd/2.
6. This symbol represents the external GTX_CLK125 and does not follow the original symbol naming convention.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
32
Freescale Semiconductor
Ethernet: Three-Speed Ethernet, MII Management
Figure 14 shows the RBMII and RTBI AC timing and multiplexing diagrams.
tRGT
tRGTH
GTX_CLK
(At Transmitter)
tSKRGT
TXD[8:5][3:0]
TXD[7:4][3:0]
TX_CTL
TXD[3:0]
TXD[8:5]
TXD[7:4]
TXD[4]
TXEN
TXD[9]
TXERR
tSKRGT
TX_CLK
(At PHY)
RXD[8:5][3:0]
RXD[7:4][3:0]
RXD[8:5]
RXD[3:0] RXD[7:4]
tSKRGT
RX_CTL
RXD[4]
RXDV
RXD[9]
RXERR
tSKRGT
RX_CLK
(At PHY)
Figure 14. RGMII and RTBI AC Timing and Multiplexing Diagrams
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
33
8.3
Ethernet Management Interface Electrical Characteristics
The electrical characteristics specified here apply to the MII management interface signals management
data input/output (MDIO) and management data clock (MDC). The electrical characteristics for GMII,
RGMII, TBI and RTBI are specified in Section 8.1, “Three-Speed Ethernet Controller (TSEC)
—GMII/MII/TBI/RGMII/RTBI Electrical Characteristics.”
8.3.1
MII Management DC Electrical Characteristics
The MDC and MDIO are defined to operate at a supply voltage of 2.5 V or 3.3 V. The DC electrical
characteristics for MDIO and MDC are provided in Table 31 and Table 32.
Table 31. MII Management DC Electrical Characteristics Powered at 2.5 V
Parameter
Symbol
Conditions
Min
Max
Unit
Supply voltage (2.5 V)
LVDD
—
2.37
2.63
V
Output high voltage
VOH
IOH = –1.0 mA
LVDD = Min
2.00
LVDD + 0.3
V
Output low voltage
VOL
IOL = 1.0 mA
LVDD = Min
GND - 0.3
0.40
V
Input high voltage
VIH
—
LVDD = Min
1.7
—
V
Input low voltage
VIL
—
LVDD = Min
-0.3
0.70
V
Input high current
IIH
VIN = LVDD
—
10
μA
Input low current
IIL
VIN = LVDD
-15
—
μA
1
Note:
1. The symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2.
Table 32. MII Management DC Electrical Characteristics Powered at 3.3 V
Parameter
Symbol
Conditions
Min
Max
Unit
Supply voltage (3.3 V)
LVDD
—
2.97
3.63
V
Output high voltage
VOH
IOH = –1.0 mA
LVDD = Min
2.10
LVDD + 0.3
V
Output low voltage
VOL
IOL = 1.0 mA
LVDD = Min
GND
0.50
V
Input high voltage
VIH
—
2.00
—
V
Input low voltage
VIL
—
—
0.80
V
Input high current
IIH
LVDD = Max
VIN 1 = 2.1 V
—
40
μA
Input low current
IIL
LVDD = Max
VIN = 0.5 V
–600
—
μA
Note:
1. The symbol VIN, in this case, represents the LVIN symbol referenced in Table 1 and Table 2.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
34
Freescale Semiconductor
8.3.2
MII Management AC Electrical Specifications
Table 33 provides the MII management AC timing specifications.
Table 33. MII Management AC Timing Specifications
At recommended operating conditions with LVDD is 3.3 V ± 10% or 2.5 V ± 5%
Symbol 1
Min
Typ
Max
Unit
Notes
MDC frequency
fMDC
—
2.5
—
MHz
2
MDC period
tMDC
—
400
—
ns
MDC clock pulse width high
tMDCH
32
—
—
ns
MDC to MDIO delay
tMDKHDX
10
—
170
ns
MDIO to MDC setup time
tMDDVKH
5
—
—
ns
MDIO to MDC hold time
tMDDXKH
0
—
—
ns
MDC rise time
tMDCR
—
—
10
ns
MDC fall time
tMDHF
—
—
10
ns
Parameter/Condition
3
Notes:
1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state)
(reference)(state) for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example,
tMDKHDX symbolizes management data timing (MD) for the time tMDC from clock reference (K) high (H) until data
outputs (D) are invalid (X) or data hold time. Also, tMDDVKH symbolizes management data timing (MD) with
respect to the time data input signals (D) reach the valid state (V) relative to the tMDC clock reference (K) going
to the high (H) state or setup time. For rise and fall times, the latter convention is used with the appropriate letter:
R (rise) or F (fall).
2. This parameter is dependent on the csb_clk speed (that is, for a csb_clk of 267 MHz, the maximum frequency
is 8.3 MHz and the minimum frequency is 1.2 MHz; for a csb_clk of 375 MHz, the maximum frequency is
11.7 MHz and the minimum frequency is 1.7 MHz).
3. This parameter is dependent on the csb_clk speed (that is, for a csb_clk of 267 MHz, the delay is 70 ns and for
a csb_clk of 333 MHz, the delay is 58 ns).
Figure 15 shows the MII management AC timing diagram.
tMDCR
tMDC
MDC
tMDCF
tMDCH
MDIO
(Input)
tMDDVKH
tMDDXKH
MDIO
(Output)
tMDKHDX
Figure 15. MII Management Interface Timing Diagram
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
35
USB
9
USB
This section provides the AC and DC electrical specifications for the USB interface of the MPC8347EA.
9.1
USB DC Electrical Characteristics
Table 34 provides the DC electrical characteristics for the USB interface.
Table 34. USB DC Electrical Characteristics
Parameter
Symbol
Min
Max
Unit
High-level input voltage
VIH
2
OVDD + 0.3
V
Low-level input voltage
VIL
–0.3
0.8
V
Input current
IIN
—
±5
μA
High-level output voltage,
IOH = –100 μA
VOH
OVDD – 0.2
—
V
Low-level output voltage,
IOL = 100 μA
VOL
—
0.2
V
Note:
1. The symbol VIN, in this case, represents the OVIN symbol referenced in Table 1 and Table 2.
9.2
USB AC Electrical Specifications
Table 35 describes the general timing parameters of the USB interface of the MPC8347EA.
Table 35. USB General Timing Parameters
Symbol 1
Min
Max
Unit
tUSCK
15
—
ns
Input setup to usb clock - all inputs
tUSIVKH
4
—
ns
input hold to usb clock - all inputs
tUSIXKH
1
—
ns
usb clock to output valid - all outputs
tUSKHOV
—
7
ns
Output hold from usb clock - all outputs
tUSKHOX
2
—
ns
Parameter
usb clock cycle time
Notes
Notes:
1. The symbols for timing specifications follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state)
for inputs and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tUSIXKH symbolizes
usb timing (US) for the input (I) to go invalid (X) with respect to the time the usb clock reference (K) goes high (H).
Also, tUSKHOX symbolizes USB timing (US) for the USB clock reference (K) to go high (H), with respect to the output
(O) going invalid (X) or output hold time.
2. All timings are in reference to USB clock.
3. All signals are measured from OVDD/2 of the rising edge of the USB clock to 0.4 × OVDD of the signal in question
for 3.3 V signaling levels.
4. Input timings are measured at the pin.
5. For active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through
the component pin is less than or equal to that of the leakage current specification.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
36
Freescale Semiconductor
USB
Figure 16 and Figure 17 provide the AC test load and signals for the USB, respectively.
Output
Z0 = 50 Ω
RL = 50 Ω
OVDD/2
Figure 16. USB AC Test Load
USB0_CLK/USB1_CLK/DR_CLK
tUSIVKH
tUSIXKH
Input Signals
tUSKHOV
tUSKHOX
Output Signals:
Figure 17. USB Signals
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
37
Local Bus
10 Local Bus
This section describes the DC and AC electrical specifications for the local bus interface of the
MPC8347EA.
10.1
Local Bus DC Electrical Characteristics
Table 36 provides the DC electrical characteristics for the local bus interface.
Table 36. Local Bus DC Electrical Characteristics
Parameter
10.2
Symbol
Min
Max
Unit
High-level input voltage
VIH
2
OVDD + 0.3
V
Low-level input voltage
VIL
–0.3
0.8
V
Input current
IIN
—
±5
μA
High-level output voltage,
IOH = –100 μA
VOH
OVDD – 0.2
—
V
Low-level output voltage,
IOL = 100 μA
VOL
—
0.2
V
Local Bus AC Electrical Specification
Table 37 and Table 38 describe the general timing parameters of the local bus interface of the
MPC8347EA.
Table 37. Local Bus General Timing Parameters—DLL on
Symbol 1
Min
Max
Unit
Notes
tLBK
7.5
—
ns
2
Input setup to local bus clock (except LUPWAIT)
tLBIVKH1
1.5
—
ns
3, 4
LUPWAIT input setup to local bus clock
tLBIVKH2
2.2
—
ns
3, 4
Input hold from local bus clock (except LUPWAIT)
tLBIXKH1
1.0
—
ns
3, 4
LUPWAIT Input hold from local bus clock
tLBIXKH2
1.0
—
ns
3, 4
LALE output fall to LAD output transition (LATCH hold time)
tLBOTOT1
1.5
—
ns
5
LALE output fall to LAD output transition (LATCH hold time)
tLBOTOT2
3
—
ns
6
LALE output fall to LAD output transition (LATCH hold time)
tLBOTOT3
2.5
—
ns
7
Local bus clock to LALE rise
tLBKHLR
—
4.5
ns
Local bus clock to output valid (except LAD/LDP and LALE)
tLBKHOV1
—
4.5
ns
Local bus clock to data valid for LAD/LDP
tLBKHOV2
—
4.5
ns
3
Local bus clock to address valid for LAD
tLBKHOV3
—
4.5
ns
3
Output hold from local bus clock (except LAD/LDP and LALE)
tLBKHOX1
1
—
ns
3
Output hold from local bus clock for LAD/LDP
tLBKHOX2
1
—
ns
3
Parameter
Local bus cycle time
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
38
Freescale Semiconductor
Local Bus
Table 37. Local Bus General Timing Parameters—DLL on (continued)
Parameter
Local bus clock to output high impedance for LAD/LDP
Symbol 1
Min
Max
Unit
tLBKHOZ
—
3.8
ns
Notes
Notes:
1. The symbols for timing specifications follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs
and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing
(LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock
one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to go high (H), with respect to the output
(O) going invalid (X) or output hold time.
2. All timings are in reference to the rising edge of LSYNC_IN.
3. All signals are measured from OVDD/2 of the rising edge of LSYNC_IN to 0.4 × OVDD of the signal in question for 3.3 V
signaling levels.
4. Input timings are measured at the pin.
5.tLBOTOT1 should be used when RCWH[LALE] is not set and when the load on the LALE output pin is at least 10 pF less than
the load on the LAD output pins.
6.tLBOTOT2 should be used when RCWH[LALE] is set and when the load on the LALE output pin is at least 10 pF less than the
load on the LAD output pins.
7.tLBOTOT3 should be used when RCWH[LALE] is set and when the load on the LALE output pin equals the load on the LAD
output pins.
8. For active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through the
component pin is less than or equal to that of the leakage current specification.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
39
Local Bus
Table 38. Local Bus General Timing Parameters—DLL Bypass
Symbol 1
Min
Max
Unit
Notes
tLBK
15
—
ns
2
Input setup to local bus clock
tLBIVKH
7
—
ns
3, 4
Input hold from local bus clock
tLBIXKH
1.0
—
ns
3, 4
LALE output fall to LAD output transition (LATCH hold time)
tLBOTOT1
1.5
—
ns
5
LALE output fall to LAD output transition (LATCH hold time)
tLBOTOT2
3
—
ns
6
LALE output fall to LAD output transition (LATCH hold time)
tLBOTOT3
2.5
—
ns
7
Local bus clock to output valid
tLBKHOV
—
3
ns
3
Local bus clock to output high impedance for LAD/LDP
tLBKHOZ
—
4
ns
Parameter
Local bus cycle time
Notes:
1. The symbols for timing specifications follow the pattern of t(First two letters of functional block)(signal)(state) (reference)(state) for inputs
and t(First two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tLBIXKH1 symbolizes local bus timing
(LB) for the input (I) to go invalid (X) with respect to the time the tLBK clock reference (K) goes high (H), in this case for clock
one(1). Also, tLBKHOX symbolizes local bus timing (LB) for the tLBK clock reference (K) to go high (H), with respect to the output
(O) going invalid (X) or output hold time.
2. All timings are in reference to the falling edge of LCLK0 (for all outputs and for LGTA and LUPWAIT inputs) or the rising edge
of LCLK0 (for all other inputs).
3. All signals are measured from OVDD/2 of the rising/falling edge of LCLK0 to 0.4 × OVDD of the signal in question for 3.3 V
signaling levels.
4. Input timings are measured at the pin.
5.tLBOTOT1 should be used when RCWH[LALE] is not set and when the load on the LALE output pin is at least 10 pF less than
the load on the LAD output pins.
6.tLBOTOT2 should be used when RCWH[LALE] is set and when the load on the LALE output pin is at least 10 pF less than the
load on the LAD output pins.the
7.tLBOTOT3 should be used when RCWH[LALE] is set and when the load on the LALE output pin equals to the load on the LAD
output pins.
8. For purposes of active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered
through the component pin is less than or equal to the leakage current specification.
9. DLL bypass mode is not recommended for use at frequencies above 66 MHz.
Figure 18 provides the AC test load for the local bus.
Output
Z0 = 50 Ω
RL = 50 Ω
OVDD/2
Figure 18. Local Bus C Test Load
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
40
Freescale Semiconductor
Local Bus
Figure 19 through Figure 24 show the local bus signals.
LSYNC_IN
tLBIXKH
tLBIVKH
Input Signals:
LAD[0:31]/LDP[0:3]
tLBIXKH
Output Signals:
LSDA10/LSDWE/LSDRAS/
LSDCAS/LSDDQM[0:3]
LA[27:31]/LBCTL/LBCKE/LOE/
tLBKHOV
tLBKHOX
tLBKHOV
tLBKHOZ
tLBKHOX
Output (Data) Signals:
LAD[0:31]/LDP[0:3]
tLBKHOV
tLBKHOZ
tLBKHOX
Output (Address) Signal:
LAD[0:31]
tLBKHLR
tLBOTOT
LALE
Figure 19. Local Bus Signals, Nonspecial Signals Only (DLL Enabled)
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
41
Local Bus
LCLK[n]
tLBIVKH
Input Signals:
LAD[0:31]/LDP[0:3]
tLBIXKH
tLBIXKH
tLBIVKH
Input Signal:
LGTA
tLBIXKH
Output Signals:
LSDA10/LSDWE/LSDRAS/
LSDCAS/LSDDQM[0:3]
LA[27:31]/LBCTL/LBCKE/LOE/
tLBKHOV
tLBKHOV
tLBKHOZ
Output Signals:
LAD[0:31]/LDP[0:3]
tLBOTOT
LALE
Figure 20. Local Bus Signals, Nonspecial Signals Only (DLL Bypass Mode)
LSYNC_IN
T1
T3
tLBKHOV1
tLBKHOZ1
GPCM Mode Output Signals:
LCS[0:7]/LWE
tLBIVKH2
tLBIXKH2
UPM Mode Input Signal:
LUPWAIT
tLBIVKH1
tLBIXKH1
Input Signals:
LAD[0:31]/LDP[0:3]
tLBKHOV1
tLBKHOZ1
UPM Mode Output Signals:
LCS[0:7]/LBS[0:3]/LGPL[0:5]
Figure 21. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 2 (DLL Enabled)
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
42
Freescale Semiconductor
Local Bus
LCLK
T1
T3
tLBKHOV
tLBKHOZ
GPCM Mode Output Signals:
LCS[0:7]/LWE
tLBIVKH
tLBIXKH
UPM Mode Input Signal:
LUPWAIT
tLBIVKH
Input Signals:
LAD[0:31]/LDP[0:3]
(DLL Bypass Mode)
tLBKHOV
tLBIXKH
tLBKHOZ
UPM Mode Output Signals:
LCS[0:7]/LBS[0:3]/LGPL[0:5]
Figure 22. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 2 (DLL Bypass Mode)
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
43
Local Bus
LCLK
T1
T2
T3
T4
tLBKHOV
tLBKHOZ
GPCM Mode Output Signals:
LCS[0:7]/LWE
tLBIVKH
tLBIXKH
UPM Mode Input Signal:
LUPWAIT
tLBIVKH
Input Signals:
LAD[0:31]/LDP[0:3]
(DLL Bypass Mode)
tLBKHOV
tLBIXKH
tLBKHOZ
UPM Mode Output Signals:
LCS[0:7]/LBS[0:3]/LGPL[0:5]
Figure 23. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 4 (DLL Bypass Mode)
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
44
Freescale Semiconductor
Local Bus
LSYNC_IN
T1
T2
T3
T4
tLBKHOV1
tLBKHOZ1
GPCM Mode Output Signals:
LCS[0:7]/LWE
tLBIVKH2
tLBIXKH2
UPM Mode Input Signal:
LUPWAIT
tLBIVKH1
tLBIXKH1
Input Signals:
LAD[0:31]/LDP[0:3]
tLBKHOV1
tLBKHOZ1
UPM Mode Output Signals:
LCS[0:7]/LBS[0:3]/LGPL[0:5]
Figure 24. Local Bus Signals, GPCM/UPM Signals for LCCR[CLKDIV] = 4 (DLL Enabled)
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
45
JTAG
11 JTAG
This section describes the DC and AC electrical specifications for the IEEE Std. 1149.1 (JTAG) interface
of the MPC8347EA
11.1
JTAG DC Electrical Characteristics
Table 39 provides the DC electrical characteristics for the IEEE Std. 1149.1 (JTAG) interface of the
MPC8347EA.
Table 39. JTAG interface DC Electrical Characteristics
Characteristic
11.2
Symbol
Input high voltage
VIH
Input low voltage
VIL
Input current
IIN
Condition
Min
Max
Unit
OVDD – 0.3 OVDD + 0.3
–0.3
V
0.8
V
±5
μA
Output high voltage
VOH
IOH = –8.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 8.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
JTAG AC Timing Specifications
This section describes the AC electrical specifications for the IEEE Std. 1149.1™ (JTAG) interface of the
MPC8347EA. Table 40 provides the JTAG AC timing specifications as defined in Figure 26 through
Figure 29.
Table 40. JTAG AC Timing Specifications (Independent of CLKIN) 1
At recommended operating conditions (see Table 2).
Symbol 2
Min
Max
Unit
JTAG external clock frequency of operation
fJTG
0
33.3
MHz
JTAG external clock cycle time
t JTG
30
—
ns
tJTKHKL
15
—
ns
tJTGR & tJTGF
0
2
ns
tTRST
25
—
ns
Boundary-scan data
TMS, TDI
tJTDVKH
tJTIVKH
4
4
—
—
Boundary-scan data
TMS, TDI
tJTDXKH
tJTIXKH
10
10
—
—
Boundary-scan data
TDO
tJTKLDV
tJTKLOV
2
2
11
11
Parameter
JTAG external clock pulse width measured at 1.4 V
JTAG external clock rise and fall times
TRST assert time
Input setup times:
Notes
3
ns
4
ns
Input hold times:
4
ns
Valid times:
5
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
46
Freescale Semiconductor
JTAG
Table 40. JTAG AC Timing Specifications (Independent of CLKIN) 1 (continued)
At recommended operating conditions (see Table 2).
Symbol 2
Min
Max
Boundary-scan data
TDO
tJTKLDX
tJTKLOX
2
2
—
—
JTAG external clock to output high impedance:
Boundary-scan data
TDO
tJTKLDZ
tJTKLOZ
2
2
19
9
Parameter
Output hold times:
Unit
Notes
ns
5
ns
5, 6
Notes:
1. All outputs are measured from the midpoint voltage of the falling/rising edge of tTCLK to the midpoint of the signal in question.
The output timings are measured at the pins. All output timings assume a purely resistive 50 Ω load (see Figure 25).
Time-of-flight delays must be added for trace lengths, vias, and connectors in the system.
2. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tJTDVKH symbolizes JTAG device timing
(JT) with respect to the time data input signals (D) reaching the valid state (V) relative to the tJTG clock reference (K) going
to the high (H) state or setup time. Also, tJTDXKH symbolizes JTAG timing (JT) with respect to the time data input signals (D)
went invalid (X) relative to the tJTG clock reference (K) going to the high (H) state. In general, the clock reference symbol is
based on three letters representing the clock of a particular function. For rise and fall times, the latter convention is used with
the appropriate letter: R (rise) or F (fall).
3. TRST is an asynchronous level sensitive signal. The setup time is for test purposes only.
4. Non-JTAG signal input timing with respect to tTCLK.
5. Non-JTAG signal output timing with respect to tTCLK.
6. Guaranteed by design and characterization.
Figure 25 provides the AC test load for TDO and the boundary-scan outputs of the MPC8347EA.
Z0 = 50 Ω
Output
RL = 50 Ω
OVDD/2
Figure 25. AC Test Load for the JTAG Interface
Figure 26 provides the JTAG clock input timing diagram.
JTAG
External Clock
VM
VM
VM
tJTGR
tJTKHKL
tJTG
tJTGF
VM = Midpoint Voltage (OVDD/2)
Figure 26. JTAG Clock Input Timing Diagram
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
47
JTAG
Figure 27 provides the TRST timing diagram.
TRST
VM
VM
tTRST
VM = Midpoint Voltage (OVDD/2)
Figure 27. TRST Timing Diagram
Figure 28 provides the boundary-scan timing diagram.
JTAG
External Clock
VM
VM
tJTDVKH
tJTDXKH
Boundary
Data Inputs
Input
Data Valid
tJTKLDV
tJTKLDX
Boundary
Data Outputs
Output Data Valid
tJTKLDZ
Boundary
Data Outputs
Output Data Valid
VM = Midpoint Voltage (OVDD/2)
Figure 28. Boundary-Scan Timing Diagram
Figure 29 provides the test access port timing diagram.
JTAG
External Clock
VM
VM
tJTIVKH
tJTIXKH
Input
Data Valid
TDI, TMS
tJTKLOV
tJTKLOX
Output Data Valid
TDO
tJTKLOZ
TDO
Output Data Valid
VM = Midpoint Voltage (OVDD/2)
Figure 29. Test Access Port Timing Diagram
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
48
Freescale Semiconductor
I2 C
12 I2C
This section describes the DC and AC electrical characteristics for the I2C interface of the MPC8347EA.
12.1
I2C DC Electrical Characteristics
Table 41 provides the DC electrical characteristics for the I2C interface of the MPC8347EA.
Table 41. I2C DC Electrical Characteristics
At recommended operating conditions with OVDD of 3.3 V ± 10%.
Parameter
Symbol
Min
Max
Input high voltage level
VIH
0.7 × OVDD
OVDD+ 0.3
V
Input low voltage level
VIL
–0.3
0.3 × OVDD
V
Low level output voltage
VOL
0
0.2 × OVDD
V
1
tI2KLKV
20 + 0.1 × CB
250
ns
2
0
50
ns
3
4
Output fall time from VIH(min) to VIL(max) with a bus capacitance
from 10 to 400 pF
Pulse width of spikes which must be suppressed by the input filter tI2KHKL
Unit Notes
Input current each I/O pin (input voltage is between 0.1 × OVDD
and 0.9 × OVDD(max)
II
–10
10
μA
Capacitance for each I/O pin
CI
—
10
pF
Notes:
1. Output voltage (open drain or open collector) condition = 3 mA sink current.
2. CB = capacitance of one bus line in pF.
3. Refer to the MPC8349E Integrated Host Processor Reference Manual for information on the digital filter used.
4. I/O pins obstruct the SDA and SCL lines if OVDD is switched off.
12.2
I2C AC Electrical Specifications
Table 42 provides the AC timing parameters for the I2C interface of the MPC8347EA. Note that all values
refer to VIH (min) and VIL (max) levels (see Table 41).
Table 42. I2C AC Electrical Specifications
Symbol 1
Min
Max
Unit
SCL clock frequency
fI2C
0
400
kHz
Low period of the SCL clock
tI2CL
1.3
—
μs
High period of the SCL clock
tI2CH
0.6
—
μs
Setup time for a repeated START condition
tI2SVKH
0.6
—
μs
Hold time (repeated) START condition (after this period, the first clock pulse is
generated)
tI2SXKL
0.6
—
μs
Data setup time
tI2DVKH
100
—
ns
Data hold time:
tI2DXKL
—
02
—
0.9 3
Parameter
CBUS compatible masters
I2C bus devices
μs
MPC8347EAMPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
49
I2 C
Table 42. I2C AC Electrical Specifications (continued)
Symbol 1
Min
Max
Unit
Rise time of both SDA and SCL signals
tI2CR
20 + 0.1 Cb 4
300
ns
Fall time of both SDA and SCL signals
tI2CF
20 + 0.1 Cb 4
300
ns
Set-up time for STOP condition
tI2PVKH
0.6
—
μs
Bus free time between a STOP and START condition
tI2KHDX
1.3
—
μs
Noise margin at the LOW level for each connected device (including hysteresis)
VNL
0.1 × OVDD
—
V
Noise margin at the HIGH level for each connected device (including hysteresis)
VNH
0.2 × OVDD
—
V
Parameter
Notes:
1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for inputs
and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tI2DVKH symbolizes I2C timing (I2) with
respect to the time data input signals (D) reach the valid state (V) relative to the tI2C clock reference (K) going to the high
(H) state or setup time. Also, tI2SXKL symbolizes I2C timing (I2) for the time that the data with respect to the start condition
(S) goes invalid (X) relative to the tI2C clock reference (K) going to the low (L) state or hold time. Also, tI2PVKH symbolizes
I2C timing (I2) for the time that the data with respect to the stop condition (P) reaches the valid state (V) relative to the tI2C
clock reference (K) going to the high (H) state or setup time. For rise and fall times, the latter convention is used with the
appropriate letter: R (rise) or F (fall).
2. MPC8347EA provides a hold time of at least 300 ns for the SDA signal (referred to the VIHmin of the SCL signal) to bridge
the undefined region of the falling edge of SCL.
3. The maximum tI2DVKH must be met only if the device does not stretch the LOW period (tI2CL) of the SCL signal.
4. CB = capacitance of one bus line in pF.
Figure 30 provides the AC test load for the I2C.
Output
Z0 = 50 Ω
RL = 50 Ω
OVDD/2
Figure 30. I2C AC Test Load
Figure 31 shows the AC timing diagram for the I2C bus.
SDA
tI2CF
tI2DVKH
tI2CL
tI2KHKL
tI2SXKL
tI2CF
tI2CR
SCL
tI2SXKL
S
tI2CH
tI2DXKL
tI2SVKH
Sr
tI2PVKH
P
S
Figure 31. I2C Bus AC Timing Diagram
MPC8347EAMPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
50
Freescale Semiconductor
PCI
13 PCI
This section describes the DC and AC electrical specifications for the PCI bus of the MPC8347EA.
13.1
PCI DC Electrical Characteristics
Table 43 provides the DC electrical characteristics for the PCI interface of the MPC8347EA.
Table 43. PCI DC Electrical Characteristics
Parameter
Symbol
Test Condition
Min
Max
Unit
High-level input voltage
VIH
VOUT ≥ VOH (min) or
2
OVDD + 0.3
V
Low-level input voltage
VIL
VOUT ≤ VOL (max)
–0.3
0.8
V
IIN
1
VIN = 0 V or VIN = OVDD
—
±5
μA
High-level output voltage
VOH
OVDD = min,
IOH = –100 μA
OVDD – 0.2
—
V
Low-level output voltage
VOL
OVDD = min,
IOL = 100 μA
—
0.2
V
Input current
Notes:
1. The symbol VIN, in this case, represents the OVIN symbol referenced in Table 1.
13.2
PCI AC Electrical Specifications
This section describes the general AC timing parameters of the PCI bus of the MPC8347EA. Note that the
PCI_CLK or PCI_SYNC_IN signal is used as the PCI input clock depending on whether the MPC8347EA
is configured as a host or agent device. Table 44 provides the PCI AC timing specifications at 66 MHz.
Table 44. PCI AC Timing Specifications at 66 MHz6
Symbol 1
Min
Max
Unit
Notes
Clock to output valid
tPCKHOV
—
6.0
ns
2
Output hold from Clock
tPCKHOX
1
—
ns
2
Clock to output high impedance
tPCKHOZ
—
14
ns
2, 3
Input setup to Clock
tPCIVKH
3.0
—
ns
2, 4
Input hold from Clock
tPCIXKH
0
—
ns
2, 4
Parameter
Notes:
1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state)
for inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH symbolizes
PCI timing (PC) with respect to the time the input signals (I) reach the valid state (V) relative to the PCI_SYNC_IN
clock, tSYS, reference (K) going to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI timing (PC) with
respect to the time hard reset (R) went high (H) relative to the frame signal (F) going to the valid (V) state.
2. See the timing measurement conditions in the PCI 2.3 Local Bus Specifications.
3. For active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through
the component pin is less than or equal to the leakage current specification.
4. Input timings are measured at the pin.
6. PCI timing depends on M66EN and the ratio between PCI1/PCI2. Refer to the PCI chapter of the reference manual
for a description of M66EN.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
51
PCI
Table 45 provides the PCI AC timing specifications at 33 MHz.
Table 45. PCI AC Timing Specifications at 33 MHz
Symbol 1
Min
Max
Unit
Notes
Clock to output valid
tPCKHOV
—
11
ns
2
Output hold from Clock
tPCKHOX
2
—
ns
2
Clock to output high impedance
tPCKHOZ
—
14
ns
2, 3
Input setup to Clock
tPCIVKH
3.0
—
ns
2, 4
Input hold from Clock
tPCIXKH
0
—
ns
2, 4
Parameter
Notes:
1. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tPCIVKH symbolizes PCI
timing (PC) with respect to the time the input signals (I) reach the valid state (V) relative to the PCI_SYNC_IN clock,
tSYS, reference (K) going to the high (H) state or setup time. Also, tPCRHFV symbolizes PCI timing (PC) with respect
to the time hard reset (R) went high (H) relative to the frame signal (F) going to the valid (V) state.
2. See the timing measurement conditions in the PCI 2.3 Local Bus Specifications.
3. For active/float timing measurements, the Hi-Z or off state is defined to be when the total current delivered through
the component pin is less than or equal to the leakage current specification.
4. Input timings are measured at the pin.
Figure 32 provides the AC test load for PCI.
Output
Z0 = 50 Ω
RL = 50 Ω
OVDD/2
Figure 32. PCI AC Test Load
Figure 33 shows the PCI input AC timing diagram.
CLK
tPCIVKH
tPCIXKH
Input
Figure 33. PCI Input AC Timing Diagram
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
52
Freescale Semiconductor
PCI
Figure 34 shows the PCI output AC timing diagram.
CLK
tPCKHOV
tPCKHOX
Output Delay
tPCKHOZ
High-Impedance
Output
Figure 34. PCI Output AC Timing Diagram
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
53
Timers
14 Timers
This section describes the DC and AC electrical specifications for the timers.
14.1
Timer DC Electrical Characteristics
Table 46 provides the DC electrical characteristics for the MPC8347EA timer pins, including TIN, TOUT,
TGATE, and RTC_CLK.
Table 46. Timer DC Electrical Characteristics
Characteristic
14.2
Symbol
Condition
Min
Max
Unit
Input high voltage
VIH
2.0
OVDD+0.3
V
Input low voltage
VIL
-0.3
0.8
V
Input current
IIN
±5
μA
Output high voltage
VOH
IOH = –8.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 8.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
Timer AC Timing Specifications
Table 47 provides the timer input and output AC timing specifications.
Table 47. Timers Input AC Timing Specifications 1
Characteristic
Timers inputs—minimum pulse width
Symbol 2
Min
Unit
tTIWID
20
ns
Notes:
1. Input specifications are measured from the 50 percent level of the signal to the 50 percent level of the rising edge of
CLKIN. Timings are measured at the pin.
2. Timer inputs and outputs are asynchronous to any visible clock. Timer outputs should be synchronized before use by
external synchronous logic. Timer inputs are required to be valid for at least tTIWID ns to ensure proper operation.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
54
Freescale Semiconductor
GPIO
15 GPIO
This section describes the DC and AC electrical specifications for the GPIO.
15.1
GPIO DC Electrical Characteristics
Table 48 provides the DC electrical characteristics for the MPC8347EA GPIO.
Table 48. GPIO DC Electrical Characteristics
Characteristic
15.2
Symbol
Condition
Min
Max
Unit
Input high voltage
VIH
2.0
OVDD+0.3
V
Input low voltage
VIL
–0.3
0.8
V
Input current
IIN
±5
μA
Output high voltage
VOH
IOH = –8.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 8.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
GPIO AC Timing Specifications
Table 49 provides the GPIO input and output AC timing specifications.
Table 49. GPIO Input AC Timing Specifications 1
Characteristic
GPIO inputs—minimum pulse width
Symbol 2
Min
Unit
tPIWID
20
ns
Notes:
1. Input specifications are measured from the 50 percent level of the signal to the 50 percent level of the rising edge of CLKIN.
Timings are measured at the pin.
2. GPIO inputs and outputs are asynchronous to any visible clock. GPIO outputs should be synchronized before use by
external synchronous logic. GPIO inputs must be valid for at least tPIWID ns to ensure proper operation.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
55
IPIC
16 IPIC
This section describes the DC and AC electrical specifications for the external interrupt pins.
16.1
IPIC DC Electrical Characteristics
Table 50 provides the DC electrical characteristics for the external interrupt pins.
Table 50. IPIC DC Electrical Characteristics
Characteristic
Symbol
Condition
Min
Max
Unit
Input high voltage
VIH
2.0
OVDD+0.3
V
Input low voltage
VIL
–0.3
0.8
V
Input current
IIN
±5
μA
Output low voltage
VOL
IOL = 8.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
Notes:
1. This table applies for pins IRQ[0:7], IRQ_OUT and MCP_OUT.
2. IRQ_OUT and MCP_OUT are open-drain pins; thus VOH is not relevant for those pins.
16.2
IPIC AC Timing Specifications
Table 51 provides the IPIC input and output AC timing specifications.
Table 51. IPIC Input AC Timing Specifications 1
Characteristic
IPIC inputs—minimum pulse width
Symbol 2
Min
Unit
tPICWID
20
ns
Notes:
1. Input specifications are measured from the 50 percent level of the signal to the 50 percent level of the rising edge
of CLKIN. Timings are measured at the pin.
2. IPIC inputs and outputs are asynchronous to any visible clock. IPIC outputs should be synchronized before use by
external synchronous logic. IPIC inputs must be valid for at least tPICWID ns to ensure proper operation in edge
triggered mode.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
56
Freescale Semiconductor
SPI
17 SPI
This section describes the SPI DC and AC electrical specifications.
17.1
SPI DC Electrical Characteristics
Table 52 provides the SPI DC electrical characteristics.
Table 52. SPI DC Electrical Characteristics
Characteristic
17.2
Symbol
Condition
Min
Max
Unit
Input high voltage
VIH
2.0
OVDD+0.3
V
Input low voltage
VIL
–0.3
0.8
V
Input current
IIN
±5
μA
Output high voltage
VOH
IOH = –8.0 mA
2.4
—
V
Output low voltage
VOL
IOL = 8.0 mA
—
0.5
V
Output low voltage
VOL
IOL = 3.2 mA
—
0.4
V
SPI AC Timing Specifications
Table 53 provides the SPI input and output AC timing specifications.
Table 53. SPI AC Timing Specifications 1
Characteristic
Symbol 2
Min
Max
Unit
6
ns
SPI outputs valid—Master mode (internal clock) delay
tNIKHOV
SPI outputs hold—Master mode (internal clock) delay
tNIKHOX
SPI outputs valid—Slave mode (external clock) delay
tNEKHOV
SPI outputs hold—Slave mode (external clock) delay
tNEKHOX
2
ns
SPI inputs—Master mode (internal clock input setup time
tNIIVKH
4
ns
SPI inputs—Master mode (internal clock input hold time
tNIIXKH
0
ns
SPI inputs—Slave mode (external clock) input setup time
tNEIVKH
4
ns
SPI inputs—Slave mode (external clock) input hold time
tNEIXKH
2
ns
0.5
ns
8
ns
Notes:
1. Output specifications are measured from the 50 percent level of the rising edge of CLKIN to the 50 percent level of
the signal. Timings are measured at the pin.
2. The symbols for timing specifications follow the pattern of t(first two letters of functional block)(signal)(state) (reference)(state) for
inputs and t(first two letters of functional block)(reference)(state)(signal)(state) for outputs. For example, tNIKHOX symbolizes the
internal timing (NI) for the time SPICLK clock reference (K) goes to the high state (H) until outputs (O) are invalid (X).
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
57
SPI
Figure 35 provides the AC test load for the SPI.
Z0 = 50 Ω
Output
RL = 50 Ω
OVDD/2
Figure 35. SPI AC Test Load
Figure 36 through Figure 37 represent the AC timings from Table 53. Note that although the specifications
generally reference the rising edge of the clock, these AC timing diagrams also apply when the falling edge
is the active edge.
Figure 36 shows the SPI timings in slave mode (external clock).
SPICLK (input)
Input Signals:
SPIMOSI
(See Note)
tNEIVKH
tNEIXKH
tNEKHOX
Output Signals:
SPIMISO
(See Note)
Note: The clock edge is selectable on SPI.
Figure 36. SPI AC Timing in Slave Mode (External Clock) Diagram
Figure 37 shows the SPI timings in master mode (internal clock).
SPICLK (output)
Input Signals:
SPIMISO
(See Note)
tNIIVKH
Output Signals:
SPIMOSI
(See Note)
tNIIXKH
tNIKHOX
Note: The clock edge is selectable on SPI.
Figure 37. SPI AC Timing in Master Mode (Internal Clock) Diagram
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
58
Freescale Semiconductor
Package and Pin Listings
18 Package and Pin Listings
This section details package parameters, pin assignments, and dimensions. The MPC8347EA is available
in two packages a tape ball grid array (TBGA) and a plastic ball grid array (PBGA). See Section 18.1,
“Package Parameters for the MPC8347EA TBGA,” and Section 18.2, “Mechanical Dimensions of the
MPC8347EA TBGA,” and Section 18.3, “Package Parameters for the MPC8347EA PBGA” and
Section 18.4, “Mechanical Dimensions of the MPC8347EA PBGA.”
18.1
Package Parameters for the MPC8347EA TBGA
The package parameters are provided in the following list. The package type is 35 mm × 35 mm, 672 tape
ball grid array (TBGA).
Package outline
35 mm × 35 mm
Interconnects
672
Pitch
1.00 mm
Module height (typical)
1.46 mm
Solder Balls
62 Sn/36 Pb/2 Ag (ZU package)
95.5 Sn/0.5 Cu/4Ag (VV package)
Ball diameter (typical)
0.64 mm
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
59
Package and Pin Listings
18.2
Mechanical Dimensions of the MPC8347EA TBGA
Figure 38 shows the mechanical dimensions and bottom surface nomenclature of the MPC8347EA,
672-TBGA package.
Figure 38. Mechanical Dimensions and Bottom Surface Nomenclature of the MPC8347EA TBGA
NOTES
1.
2.
3.
4.
5.
All dimensions are in millimeters.
Dimensions and tolerances per ASME Y14.5M-1994.
Maximum solder ball diameter measured parallel to datum A.
Datum A, the seating plane, is determined by the spherical crowns of the solder balls.
Parallelism measurement must exclude any effect of mark on top surface of package.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
60
Freescale Semiconductor
Package and Pin Listings
18.3
Package Parameters for the MPC8347EA PBGA
The package parameters are as provided in the following list. The package type is 29 mm × 29 mm,
620 Plastic ball grid array (PBGA).
Package outline
29 mm × 29 mm
Interconnects
620
Pitch
1.00 mm
Module height (maximum)
2.46 mm
Module height (typical)
2.23 mm
Module height (minimum)
2.00 mm
Solder Balls
62 Sn/36 Pb/2 Ag (ZQ package)
95.5 Sn/0.5 Cu/4Ag (VR package)
Ball diameter (typical)
0.60 mm
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
61
Package and Pin Listings
18.4
Mechanical Dimensions of the MPC8347EA PBGA
Figure 39 shows the mechanical dimensions and bottom surface nomenclature of theMPC8347EA ,
620-PBGA package.
Figure 39. Mechanical Dimensions and Bottom Surface Nomenclature of the MPC8347EA PBGA
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
62
Freescale Semiconductor
Package and Pin Listings
NOTE
1.
2.
3.
4.
All dimensions in millimeters
Dimensioning and tolerancing per ASME Y14. 5M-1994
Maximum solder ball diameter measured parallel to datum A
Datum A, the seating plane, is determined by the spherical crowns of the solder balls.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
63
18.5
Pinout Listings
Table 51 provides the pin-out listing for the MPC8347EA, 672 TBGA package.
Table 54. MPC8347EA (TBGA) Pinout Listing
Signal
Package Pin Number
Pin Type
Power
Supply
Notes
2
PCI
PCI_INTA/IRQ_OUT
B34
O
OVDD
PCI_RESET_OUT
C33
O
OVDD
PCI_AD[31:0]
G30, G32, G34, H31, H32, H33, H34, J29,
J32, J33, L30, K31, K33, K34, L33, L34,
P34, R29, R30, R33, R34, T31, T32, T33,
U31, U34, V31, V32, V33, V34, W33, W34
I/O
OVDD
PCI_C/BE[3:0]
J30, M31, P33, T34
I/O
OVDD
PCI_PAR
P32
I/O
OVDD
PCI_FRAME
M32
I/O
OVDD
5
PCI_TRDY
N29
I/O
OVDD
5
PCI_IRDY
M34
I/O
OVDD
5
PCI_STOP
N31
I/O
OVDD
5
PCI_DEVSEL
N30
I/O
OVDD
5
PCI_IDSEL
J31
I
OVDD
PCI_SERR
N34
I/O
OVDD
5
PCI_PERR
N33
I/O
OVDD
5
PCI_REQ[0]
D32
I/O
OVDD
PCI_REQ[1]/CPCI1_HS_ES
D34
I
OVDD
PCI_REQ[2:4]
E34, F32, G29
I
OVDD
PCI_GNT0
C34
I/O
OVDD
PCI_GNT1/CPCI1_HS_LED
D33
O
OVDD
PCI_GNT2/CPCI1_HS_ENUM
E33
O
OVDD
PCI_GNT[3:4]
F31, F33
O
OVDD
M66EN
A19
I
OVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
64
Freescale Semiconductor
Table 54. MPC8347EA (TBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
Notes
DDR SDRAM Memory Interface
MDQ[0:63]
D5, A3, C3, D3, C4, B3, C2, D4, D2, E5,
G2, H6, E4, F3, G4, G3, H1, J2, L6, M6,
H2, K6, L2, M4, N2, P4, R2, T4, P6, P3,
R1, T2, AB5, AA3, AD6, AE4, AB4, AC2,
AD3, AE6, AE3, AG4, AK5, AK4, AE2,
AG6, AK3, AK2, AL2, AL1, AM5, AP5,
AM2, AN1, AP4, AN5, AJ7, AN7, AM8,
AJ9, AP6, AL7, AL9, AN8
I/O
GVDD
MECC[0:4]/MSRCID[0:4]
W4, W3, Y3, AA6, T1
I/O
GVDD
MECC[5]/MDVAL
U1
I/O
GVDD
MECC[6:7]
Y1, Y6
I/O
GVDD
MDM[0:8]
B1, F1, K1, R4, AD4, AJ1, AP3, AP7, Y4
O
GVDD
MDQS[0:8]
B2, F5, J1, P2, AC1, AJ2, AN4, AL8, W2
I/O
GVDD
MBA[0:1]
AD1, AA5
O
GVDD
MA[0:14]
W1, U4, T3, R3, P1, M1, N1, L3, L1, K2,
Y2, K3, J3, AP2, AN6
O
GVDD
MWE
AF1
O
GVDD
MRAS
AF4
O
GVDD
MCAS
AG3
O
GVDD
MCS[0:3]
AG2, AG1, AK1, AL4
O
GVDD
MCKE[0:1]
H3, G1
O
GVDD
MCK[0:5]
U2, F4, AM3, V3, F2, AN3
O
GVDD
MCK[0:5]
U3, E3, AN2, V4, E1, AM4
O
GVDD
MODT[0:3]
AH3, AJ5, AH1, AJ4
O
GVDD
MBA[2]
H4
O
GVDD
MDIC0
AB1
I/O
—
10
MDIC1
AA1
I/O
—
10
3
Local Bus Controller Interface
LAD[0:31]
AM13, AP13, AL14, AM14, AN14, AP14,
AK15, AJ15, AM15, AN15, AP15, AM16,
AL16, AN16, AP16, AL17, AM17, AP17,
AK17, AP18, AL18, AM18, AN18, AP19,
AN19, AM19, AP20, AK19, AN20, AL20,
AP21, AN21
I/O
OVDD
LDP[0]/CKSTOP_OUT
AM21
I/O
OVDD
LDP[1]/CKSTOP_IN
AP22
I/O
OVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
65
Table 54. MPC8347EA (TBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
LDP[2]/LCS[4]
AN22
I/O
OVDD
LDP[3]/LCS[5]
AM22
I/O
OVDD
LA[27:31]
AK21, AP23, AN23, AP24, AK22
O
OVDD
LCS[0:3]
AN24, AL23, AP25, AN25
O
OVDD
LWE[0:3]/LSDDQM[0:3]/
LBS[0:3]
AK23, AP26, AL24, AM25
O
OVDD
LBCTL
AN26
O
OVDD
LALE
AK24
O
OVDD
LGPL0/LSDA10/
cfg_reset_source0
AP27
I/O
OVDD
LGPL1/LSDWE/
cfg_reset_source1
AL25
I/O
OVDD
LGPL2/
LSDRAS/LOE
AJ24
O
OVDD
LGPL3/LSDCAS/
cfg_reset_source2
AN27
I/O
OVDD
LGPL4/LGTA/LUPWAIT/LPBSE
AP28
I/O
OVDD
LGPL5/cfg_clkin_div
AL26
I/O
OVDD
LCKE
AM27
O
OVDD
LCLK[0:2]
AN28, AK26, AP29
O
OVDD
LSYNC_OUT
AM12
O
OVDD
LSYNC_IN
AJ10
I
OVDD
Notes
General Purpose I/O Timers
GPIO1[0]/DMA_DREQ0/
GTM1_TIN1/
GTM2_TIN2
F24
I/O
OVDD
GPIO1[1]/DMA_DACK0/
GTM1_TGATE1/
GTM2_TGATE2
E24
I/O
OVDD
GPIO1[2]/DMA_DDONE0/
GTM1_TOUT1
B25
I/O
OVDD
GPIO1[3]/DMA_DREQ1/
GTM1_TIN2/
GTM2_TIN1
D24
I/O
OVDD
GPIO1[4]/DMA_DACK1/
GTM1_TGATE2/
GTM2_TGATE1
A25
I/O
OVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
66
Freescale Semiconductor
Table 54. MPC8347EA (TBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
GPIO1[5]/DMA_DDONE1/
GTM1_TOUT2/
GTM2_TOUT1
B24
I/O
OVDD
GPIO1[6]/DMA_DREQ2/
GTM1_TIN3/
GTM2_TIN4
A24
I/O
OVDD
GPIO1[7]/DMA_DACK2/
GTM1_TGATE3/
GTM2_TGATE4
D23
I/O
OVDD
GPIO1[8]/DMA_DDONE2/
GTM1_TOUT3
B23
I/O
OVDD
GPIO1[9]/DMA_DREQ3/
GTM1_TIN4/
GTM2_TIN3
A23
I/O
OVDD
GPIO1[10]/DMA_DACK3/
GTM1_TGATE4/
GTM2_TGATE3
F22
I/O
OVDD
GPIO1[11]/DMA_DDONE3/
GTM1_TOUT4/
GTM2_TOUT3
E22
I/O
OVDD
MPH1_D0_ENABLEN/DR_D0_ENABLEN A26
I/O
OVDD
MPH1_D1_SER_TXD/DR_D1_SER_TXD
B26
I/O
OVDD
MPH1_D2_VMO_SE0/DR_D2_VMO_SE0 D25
I/O
OVDD
MPH1_D3_SPEED/DR_D3_SPEED
A27
I/O
OVDD
MPH1_D4_DP/DR_D4_DP
B27
I/O
OVDD
MPH1_D5_DM/DR_D5_DM
C27
I/O
OVDD
MPH1_D6_SER_RCV/DR_D6_SER_RCV D26
I/O
OVDD
MPH1_D7_DRVVBUS/DR_D7_DRVVBUS E26
I/O
OVDD
Notes
USB Port 1
MPH1_NXT/DR_SESS_VLD_NXT
D27
I
OVDD
MPH1_DIR_DPPULLUP/
DR_XCVR_SEL_DPPULLUP
A28
I/O
OVDD
MPH1_STP_SUSPEND/
DR_STP_SUSPEND
F26
O
OVDD
MPH1_PWRFAULT/
DR_RX_ERROR_PWRFAULT
E27
I
OVDD
MPH1_PCTL0/DR_TX_VALID_PCTL0
A29
O
OVDD
MPH1_PCTL1/DR_TX_VALIDH_PCTL1
D28
O
OVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
67
Table 54. MPC8347EA (TBGA) Pinout Listing (continued)
Signal
MPH1_CLK/DR_CLK
Package Pin Number
B29
Pin Type
Power
Supply
I
OVDD
Notes
USB Port 0
MPH0_D0_ENABLEN/
DR_D8_CHGVBUS
C29
I/O
OVDD
MPH0_D1_SER_TXD/
DR_D9_DCHGVBUS
A30
I/O
OVDD
MPH0_D2_VMO_SE0/
DR_D10_DPPD
E28
I/O
OVDD
MPH0_D3_SPEED/
DR_D11_DMMD
B30
I/O
OVDD
MPH0_D4_DP/
DR_D12_VBUS_VLD
C30
I/O
OVDD
MPH0_D5_DM/
DR_D13_SESS_END
A31
I/O
OVDD
MPH0_D6_SER_RCV/DR_D14
B31
I/O
OVDD
MPH0_D7_DRVVBUS/
DR_D15_IDPULLUP
C31
I/O
OVDD
MPH0_NXT/
DR_RX_ACTIVE_ID
B32
I
OVDD
MPH0_DIR_DPPULLUP/
DR_RESET
A32
I/O
OVDD
MPH0_STP_SUSPEND/
DR_TX_READY
A33
I/O
OVDD
MPH0_PWRFAULT/
DR_RX_VALIDH
C32
I
OVDD
MPH0_PCTL0/
DR_LINE_STATE0
D31
I/O
OVDD
MPH0_PCTL1/
DR_LINE_STATE1
E30
I/O
OVDD
MPH0_CLK/DR_RX_VALID
B33
I
OVDD
Programmable Interrupt Controller
MCP_OUT
AN33
O
OVDD
IRQ0/MCP_IN/GPIO2[12]
C19
I/O
OVDD
IRQ[1:5]/GPIO2[13:17]
C22, A22, D21, C21, B21
I/O
OVDD
IRQ[6]/GPIO2[18]/
CKSTOP_OUT
A21
I/O
OVDD
2
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
68
Freescale Semiconductor
Table 54. MPC8347EA (TBGA) Pinout Listing (continued)
Signal
IRQ[7]/GPIO2[19]/
CKSTOP_IN
Package Pin Number
Pin Type
Power
Supply
I/O
OVDD
C20
Notes
Ethernet Management Interface
EC_MDC
A7
O
LVDD1
EC_MDIO
E9
I/O
LVDD1
I
LVDD1
2
Gigabit Reference Clock
EC_GTX_CLK125
C8
Three-Speed Ethernet Controller (Gigabit Ethernet 1)
TSEC1_COL/GPIO2[20]
A17
I/O
OVDD
TSEC1_CRS/GPIO2[21]
F12
I/O
LVDD1
TSEC1_GTX_CLK
D10
O
LVDD1
TSEC1_RX_CLK
A11
I
LVDD1
TSEC1_RX_DV
B11
I
LVDD1
TSEC1_RX_ER/GPIO2[26]
B17
I/O
OVDD
TSEC1_RXD[7:4]/
GPIO2[22:25]
B16, D16, E16, F16
I/O
OVDD
TSEC1_RXD[3:0]
E10, A8, F10, B8
I
LVDD1
TSEC1_TX_CLK
D17
I
OVDD
TSEC1_TXD[7:4]/GPIO2[27:30]
A15, B15, A14, B14
I/O
OVDD
TSEC1_TXD[3:0]
A10, E11, B10, A9
O
LVDD1
TSEC1_TX_EN
B9
O
LVDD1
TSEC1_TX_ER/GPIO2[31]
A16
I/O
OVDD
3
Three-Speed Ethernet Controller (Gigabit Ethernet 2)
TSEC2_COL/GPIO1[21]
C14
I/O
OVDD
TSEC2_CRS/GPIO1[22]
D6
I/O
LVDD2
TSEC2_GTX_CLK
A4
O
LVDD2
TSEC2_RX_CLK
B4
I
LVDD2
TSEC2_RX_DV/GPIO1[23]
E6
I/O
LVDD2
TSEC2_RXD[7:4]/GPIO1[26:29]
A13, B13, C13, A12
I/O
OVDD
TSEC2_RXD[3:0]/GPIO1[13:16]
D7, A6, E8, B7
I/O
LVDD2
TSEC2_RX_ER/GPIO1[25]
D14
I/O
OVDD
TSEC2_TXD[7]/GPIO1[31]
B12
I/O
OVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
69
Table 54. MPC8347EA (TBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
TSEC2_TXD[6]/
DR_XCVR_TERM_SEL
C12
O
OVDD
TSEC2_TXD[5]/
DR_UTMI_OPMODE1
D12
O
OVDD
TSEC2_TXD[4]/
DR_UTMI_OPMODE0
E12
O
OVDD
TSEC2_TXD[3:0]/GPIO1[17:20]
B5, A5, F8, B6
I/O
LVDD2
TSEC2_TX_ER/GPIO1[24]
F14
I/O
OVDD
TSEC2_TX_EN/GPIO1[12]
C5
I/O
LVDD2
TSEC2_TX_CLK/GPIO1[30]
E14
I/O
OVDD
Notes
3
DUART
UART_SOUT[1:2]/
MSRCID[0:1]/LSRCID[0:1]
AK27, AN29
O
OVDD
UART_SIN[1:2]/
MSRCID[2:3]/LSRCID[2:3]
AL28, AM29
I/O
OVDD
UART_CTS[1]/
MSRCID4/LSRCID4
AP30
I/O
OVDD
UART_CTS[2]/
MDVAL/ LDVAL
AN30
I/O
OVDD
UART_RTS[1:2]
AP31, AM30
O
OVDD
I2C interface
IIC1_SDA
AK29
I/O
OVDD
2
IIC1_SCL
AP32
I/O
OVDD
2
IIC2_SDA
AN31
I/O
OVDD
2
IIC2_SCL
AM31
I/O
OVDD
2
SPI
SPIMOSI/LCS[6]
AN32
I/O
OVDD
SPIMISO/LCS[7]
AP33
I/O
OVDD
SPICLK
AK30
I/O
OVDD
SPISEL
AL31
I
OVDD
Clocks
PCI_CLK_OUT[0:2]
AN9, AP9, AM10
O
OVDD
PCI_CLK_OUT[3]/LCS[6]
AN10
O
OVDD
PCI_CLK_OUT[4]/LCS[7]
AJ11
O
OVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
70
Freescale Semiconductor
Table 54. MPC8347EA (TBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
PCI_SYNC_IN/PCI_CLOCK
AK12
I
OVDD
PCI_SYNC_OUT
AP11
O
OVDD
RTC/PIT_CLOCK
AM32
I
OVDD
CLKIN
AM9
I
OVDD
Notes
3
JTAG
TCK
E20
I
OVDD
TDI
F20
I
OVDD
4
TDO
B20
O
OVDD
3
TMS
A20
I
OVDD
4
TRST
B19
I
OVDD
4
Test
TEST
D22
I
OVDD
6
TEST_SEL
AL13
I
OVDD
7
O
OVDD
PMC
A18
QUIESCE
System Control
PORESET
C18
I
OVDD
HRESET
B18
I/O
OVDD
1
SRESET
D18
I/O
OVDD
2
I
—
9
Power for
e300 PLL
(1.2 V)
AVDD1
Thermal Management
THERM0
K32
Power and Ground Signals
AVDD1
L31
AVDD2
AP12
Power for
system PLL
(1.2 V)
AVDD2
AVDD3
AE1
Power for
DDR DLL
(1.2 V)
—
AVDD4
AJ13
Power for
LBIU DLL
(1.2 V)
AVDD4
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
71
Table 54. MPC8347EA (TBGA) Pinout Listing (continued)
Package Pin Number
Pin Type
Power
Supply
GND
A1, A34, C1, C7, C10, C11, C15, C23,
C25, C28, D1, D8, D20, D30, E7, E13,
E15, E17, E18, E21, E23, E25, E32, F6,
F19, F27, F30, F34, G31, H5, J4, J34, K30,
L5, M2, M5, M30, M33, N3, N5, P30, R5,
R32, T5, T30, U6, U29, U33, V2, V5, V30,
W6, W30, Y30, AA2, AA30, AB2, AB6,
AB30, AC3, AC6, AD31, AE5, AF2, AF5,
AF31, AG30, AG31, AH4, AJ3, AJ19,
AJ22, AK7, AK13, AK14, AK16, AK18,
AK20, AK25, AK28, AL3, AL5, AL10,
AL12, AL22, AL27, AM1, AM6, AM7,
AN12, AN17, AN34, AP1, AP8, AP34
—
—
GVDD
A2, E2, G5, G6, J5, K4, K5, L4, N4, P5, R6,
T6, U5, V1, W5, Y5, AA4, AB3, AC4, AD5,
AF3, AG5, AH2, AH5, AH6, AJ6, AK6,
AK8, AK9, AL6
Power for
DDR DRAM
I/O Voltage
(2.5 V)
GVDD
LVDD1
C9, D11
Power for
Three
Speed
Ethernet #1
and for
Ethernet
Managemen
t Interface
I/O (2.5V,
3.3V)
LVDD1
LVDD2
C6, D9
Power for
Three
Speed
Ethernet #2
I/O (2.5V,
3.3V)
LVDD2
VDD
E19, E29, F7, F9, F11,F13, F15, F17, F18,
F21, F23, F25, F29, H29, J6, K29, M29,
N6, P29, T29, U30, V6, V29, W29, AB29,
AC5, AD29, AF6, AF29, AH29, AJ8, AJ12,
AJ14, AJ16, AJ18, AJ20, AJ21, AJ23,
AJ25, AJ26, AJ27, AJ28, AJ29, AK10
Power for
Core
(1.2 V)
VDD
OVDD
B22, B28, C16, C17, C24, C26, D13, D15,
D19, D29, E31, F28, G33, H30, L29, L32,
N32, P31, R31, U32, W31, Y29, AA29,
AC30, AE31, AF30, AG29, AJ17, AJ30,
AK11, AL15, AL19, AL21, AL29, AL30,
AM20, AM23, AM24, AM26, AM28, AN11,
AN13
PCI, 10/100
Ethernet,
and other
Standard
(3.3 V)
OVDD
Signal
Notes
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
72
Freescale Semiconductor
Table 54. MPC8347EA (TBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
MVREF1
M3
I
DDR
Reference
Voltage
MVREF2
AD2
I
DDR
Reference
Voltage
—
—
Notes
No Connection
NC
W32, AA31, AA32, AA33, AA34, AB31,
AB32, AB33, AB34, AC29, AC31, AC33,
AC34, AD30, AD32, AD33, AD34, AE29,
AE30, AH32, AH33, AH34, AM33, AJ31,
AJ32, AJ33, AJ34, AK32, AK33, AK34,
AM34, AL33, AL34, AK31, AH30, AC32,
AE32, AH31, AL32, AG34, AE33, AF32,
AE34, AF34, AF33, AG33, AG32, AL11,
AM11, AP10, Y32, Y34, Y31, Y33
Notes:
1. This pin is an open-drain signal. A weak pull-up resistor (1 kΩ) should be placed on this pin to OVDD
2. This pin is an open-drain signal. A weak pull-up resistor (2–10 kΩ) should be placed on this pin to OVDD.
3. During reset, this output is actively driven rather than three-stated.
4. These JTAG pins have weak internal pull-up P-FETs that are always enabled.
5. This pin should have a weak pull-up if the chip is in PCI host mode. Follow the PCI specifications.
6. This pin must always be tied to GND
7. This pin must always be pulled up to OVDD
8. This pin must always be left not connected.
9. Thermal sensitive resistor.
10. It is recommended that MDIC0 be tied to GRD using an 18 Ω resistor and MDIC1 be tied to DDR power using an 18 Ω
resistor.
Table 52 provides the pin-out listing for the MPC8347EA, 620 PBGA package.
Table 55. MPC8347EA (PBGA) Pinout Listing
Signal
Package Pin Number
Pin Type
Power
Supply
Notes
2
PCI
PCI1_INTA/IRQ_OUT
D20
O
OVDD
PCI1_RESET_OUT
B21
O
OVDD
PCI1_AD[31:0]
E19, D17, A16, A18, B17, B16, D16, B18,
E17, E16, A15, C16, D15, D14, C14, A12,
D12, B11, C11, E12, A10, C10, A9, E11,
E10, B9, B8, D9, A8, C9, D8, C8
I/O
OVDD
PCI1_C/BE[3:0]
A17, A14, A11, B10
I/O
OVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
73
Table 55. MPC8347EA (PBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
Notes
PCI1_PAR
D13
I/O
OVDD
PCI1_FRAME
B14
I/O
OVDD
5
PCI1_TRDY
A13
I/O
OVDD
5
PCI1_IRDY
E13
I/O
OVDD
5
PCI1_STOP
C13
I/O
OVDD
5
PCI1_DEVSEL
B13
I/O
OVDD
5
PCI1_IDSEL
C17
I
OVDD
PCI1_SERR
C12
I/O
OVDD
5
PCI1_PERR
B12
I/O
OVDD
5
PCI1_REQ[0]
A21
I/O
OVDD
PCI1_REQ[1]/
CPCI1_HS_ES
C19
I
OVDD
PCI1_REQ[2:4]
C18, A19, E20
I
OVDD
PCI1_GNT0
B20
I/O
OVDD
PCI1_GNT1/
CPCI1_HS_LED
C20
O
OVDD
PCI1_GNT2/
CPCI1_HS_ENUM
B19
O
OVDD
PCI1_GNT[3:4]
A20, E18
O
OVDD
M66EN
L26
I
OVDD
DDR SDRAM Memory Interface
MDQ[0:63]
AC25, AD27, AD25, AH27, AE28, AD26,
AD24, AF27, AF25, AF28, AH24, AG26,
AE25, AG25, AH26, AH25, AG22, AH22,
AE21, AD19, AE22, AF23, AE19, AG20,
AG19, AD17, AE16, AF16, AF18, AG18,
AH17, AH16, AG9, AD12, AG7, AE8, AD11,
AH9, AH8, AF6, AF8, AE6, AF1, AE4, AG8,
AH3, AG3, AG4, AH2, AD7, AB4, AB3, AG1,
AD5, AC2, AC1, AC4, AA3, Y4, AA4, AB1,
AB2, Y5, Y3
I/O
GVDD
MECC[0:4]/MSRCID[0:4]
AG13, AE14, AH12, AH10, AE15
I/O
GVDD
MECC[5]/MDVAL
AH14
I/O
GVDD
MECC[6:7]
AE13, AH11
I/O
GVDD
MDM[0:8]
AG28, AG24, AF20, AG17, AE9, AH5, AD1,
AA2, AG12
O
GVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
74
Freescale Semiconductor
Table 55. MPC8347EA (PBGA) Pinout Listing (continued)
Package Pin Number
Pin Type
Power
Supply
MDQS[0:8]
AE27, AE26, AE20, AH18, AG10, AF5, AC3,
AA1, AH13
I/O
GVDD
MBA[0:1]
AF10, AF11
O
GVDD
MA[0:14]
AF13, AF15, AG16, AD16, AF17, AH20,
AH19, AH21, AD18, AG21, AD13, AF21,
AF22, AE1, AA5
O
GVDD
MWE
AD10
O
GVDD
MRAS
AF7
O
GVDD
MCAS
AG6
O
GVDD
MCS[0:3]
AE7, AH7, AH4, AF2
O
GVDD
MCKE[0:1]
AG23, AH23
O
GVDD
MCK[0:5]
AH15, AE24, AE2, AF14, AE23, AD3
O
GVDD
MCK[0:5]
AG15, AD23, AE3, AG14, AF24, AD2
O
GVDD
MODT[0:3]
AG5, AD4, AH6, AF4
O
GVDD
MBA[2]
AD22
O
GVDD
MDIC0
AG11
I/O
—
9
MDIC1
AF12
I/O
—
9
Signal
Notes
3
Local Bus Controller Interface
LAD[0:31]
T4, T5, T1, R2, R3, T2, R1, R4, P1, P2, P3,
P4, N1, N4, N2, N3, M1, M2, M3, N5, M4,
L1, L2, L3, K1, M5, K2, K3, J1, J2, L5, J3
I/O
OVDD
LDP[0]/CKSTOP_OUT
H1
I/O
OVDD
LDP[1]/CKSTOP_IN
K5
I/O
OVDD
LDP[2]/LCS[4]
H2
I/O
OVDD
LDP[3]/LCS[5]
G1
I/O
OVDD
LA[27:31]
J4, H3, G2, F1, G3
O
OVDD
LCS[0:3]
J5, H4, F2, E1
O
OVDD
LWE[0:3]/LSDDQM[0:3]/
LBS[0:3]
F3, G4, D1, E2
O
OVDD
LBCTL
H5
O
OVDD
LALE
E3
O
OVDD
LGPL0/LSDA10/
cfg_reset_source0
F4
I/O
OVDD
LGPL1/LSDWE/
cfg_reset_source1
D2
I/O
OVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
75
Table 55. MPC8347EA (PBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
LGPL2/
LSDRAS/LOE
C1
O
OVDD
LGPL3/LSDCAS/
cfg_reset_source2
C2
I/O
OVDD
LGPL4/LGTA/LUPWAIT/LPBSE
C3
I/O
OVDD
LGPL5/cfg_clkin_div
B3
I/O
OVDD
LCKE
E4
O
OVDD
LCLK[0:2]
D4, A3, C4
O
OVDD
LSYNC_OUT
U3
O
OVDD
LSYNC_IN
Y2
I
OVDD
Notes
General Purpose I/O Timers
GPIO1[0]/DMA_DREQ0/
GTM1_TIN1/
GTM2_TIN2
D27
I/O
OVDD
GPIO1[1]/DMA_DACK0/
GTM1_TGATE1/
GTM2_TGATE2
E26
I/O
OVDD
GPIO1[2]/DMA_DDONE0/
GTM1_TOUT1
D28
I/O
OVDD
GPIO1[3]/DMA_DREQ1/
GTM1_TIN2/
GTM2_TIN1
G25
I/O
OVDD
GPIO1[4]/DMA_DACK1/
GTM1_TGATE2/
GTM2_TGATE1
J24
I/O
OVDD
GPIO1[5]/DMA_DDONE1/
GTM1_TOUT2/
GTM2_TOUT1
F26
I/O
OVDD
GPIO1[6]/DMA_DREQ2/
GTM1_TIN3/
GTM2_TIN4
E27
I/O
OVDD
GPIO1[7]/DMA_DACK2/
GTM1_TGATE3/
GTM2_TGATE4
E28
I/O
OVDD
GPIO1[8]/DMA_DDONE2/
GTM1_TOUT3
H25
I/O
OVDD
GPIO1[9]/DMA_DREQ3/
GTM1_TIN4/
GTM2_TIN3
F27
I/O
OVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
76
Freescale Semiconductor
Table 55. MPC8347EA (PBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
GPIO1[10]/DMA_DACK3/
GTM1_TGATE4/
GTM2_TGATE3
K24
I/O
OVDD
GPIO1[11]/DMA_DDONE3/
GTM1_TOUT4/
GTM2_TOUT3
G26
I/O
OVDD
MPH1_D0_ENABLEN/DR_D0_ENABLEN C28
I/O
OVDD
MPH1_D1_SER_TXD/DR_D1_SER_RXD F25
I/O
OVDD
MPH1_D2_VMO_SE0/DR_D2_VMO_SE0 B28
I/O
OVDD
MPH1_D3_SPEED/DR_D3_SPEED
C27
I/O
OVDD
MPH1_D4_DP/DR_D4_DP
D26
I/O
OVDD
MPH1_D5_DM/DR_D5_DM
E25
I/O
OVDD
MPH1_D6_SER_RCV/DR_D6_SER_RCV C26
I/O
OVDD
MPH1_D7_DRVVBUS/DR_D7_DRVVBUS D25
I/O
OVDD
Notes
USB Port 1
MPH1_NXT/DR_SESS_VLD_NXT
B26
I
OVDD
MPH1_DIR_DPPULLUP/
DR_XCVR_SEL_DPPULLUP
E24
I/O
OVDD
MPH1_STP_SUSPEND/
DR_STP_SUSPEND
A27
O
OVDD
MPH1_PWRFAULT/
DR_RX_ERROR_PWRFAULT
C25
I
OVDD
MPH1_PCTL0/DR_TX_VALID_PCTL0
A26
O
OVDD
MPH1_PCTL1/DR_TX_VALIDH_PCTL1
B25
O
OVDD
MPH1_CLK/DR_CLK
A25
I
OVDD
USB Port 0
MPH0_D0_ENABLEN/
DR_D8_CHGVBUS
D24
I/O
OVDD
MPH0_D1_SER_TXD/
DR_D9_DCHGVBUS
C24
I/O
OVDD
MPH0_D2_VMO_SE0/
DR_D10_DPPD
B24
I/O
OVDD
MPH0_D3_SPEED/
DR_D11_DMMD
A24
I/O
OVDD
MPH0_D4_DP/
DR_D12_VBUS_VLD
D23
I/O
OVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
77
Table 55. MPC8347EA (PBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
MPH0_D5_DM/
DR_D13_SESS_END
C23
I/O
OVDD
MPH0_D6_SER_RCV/DR_D14
B23
I/O
OVDD
MPH0_D7_DRVVBUS/
DR_D15_IDPULLUP
A23
I/O
OVDD
MPH0_NXT/
DR_RX_ACTIVE_ID
D22
I
OVDD
MPH0_DIR_DPPULLUP/
DR_RESET
C22
I/O
OVDD
MPH0_STP_SUSPEND/
DR_TX_READY
B22
I/O
OVDD
MPH0_PWRFAULT/
DR_RX_VALIDH
A22
I
OVDD
MPH0_PCTL0/
DR_LINE_STATE0
E21
I/O
OVDD
MPH0_PCTL1/
DR_LINE_STATE1
D21
I/O
OVDD
MPH0_CLK/DR_RX_VALID
C21
I
OVDD
Notes
Programmable Interrupt Controller
MCP_OUT
E8
O
OVDD
IRQ0/MCP_IN/GPIO2[12]
J28
I/O
OVDD
IRQ[1:5]/GPIO2[13:17]
K25, J25, H26, L24, G27
I/O
OVDD
IRQ[6]/GPIO2[18]/
CKSTOP_OUT
G28
I/O
OVDD
IRQ[7]/GPIO2[19]/
CKSTOP_IN
J26
I/O
OVDD
2
Ethernet Management Interface
EC_MDC
Y24
O
LVDD1
EC_MDIO
Y25
I/O
LVDD1
I
LVDD1
2
Gigabit Reference Clock
EC_GTX_CLK125
Y26
Three-Speed Ethernet Controller (Gigabit Ethernet 1)
TSEC1_COL/GPIO2[20]
M26
I/O
OVDD
TSEC1_CRS/GPIO2[21]
U25
I/O
LVDD1
TSEC1_GTX_CLK
V24
O
LVDD1
3
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
78
Freescale Semiconductor
Table 55. MPC8347EA (PBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
TSEC1_RX_CLK
U26
I
LVDD1
TSEC1_RX_DV
U24
I
LVDD1
TSEC1_RX_ER/GPIO2[26]
L28
I/O
OVDD
TSEC1_RXD[7:4]/GPIO2[22:25]
M27, M28, N26, N27
I/O
OVDD
TSEC1_RXD[3:0]
W26, W24, Y28, Y27
I
LVDD1
TSEC1_TX_CLK
N25
I
OVDD
TSEC1_TXD[7:4]/GPIO2[27:30]
N28, P25, P26, P27
I/O
OVDD
TSEC1_TXD[3:0]
V28, V27, V26, W28
O
LVDD1
TSEC1_TX_EN
W27
O
LVDD1
TSEC1_TX_ER/GPIO2[31]
N24
I/O
OVDD
Notes
Three-Speed Ethernet Controller (Gigabit Ethernet 2)
TSEC2_COL/GPIO1[21]
P28
I/O
OVDD
TSEC2_CRS/GPIO1[22]
AC28
I/O
LVDD2
TSEC2_GTX_CLK
AC27
O
LVDD2
TSEC2_RX_CLK
AB25
I
LVDD2
TSEC2_RX_DV/GPIO1[23]
AC26
I/O
LVDD2
TSEC2_RXD[7:4]/GPIO1[26:29]
R28, T24, T25, T26
I/O
OVDD
TSEC2_RXD[3:0]/GPIO1[13:16]
AA25, AA26, AA27, AA28
I/O
LVDD2
TSEC2_RX_ER/GPIO1[25]
R25
I/O
OVDD
TSEC2_TXD[7]/GPIO1[31]
T27
I/O
OVDD
TSEC2_TXD[6]/DR_XCVR_TERM_SEL
T28
O
OVDD
TSEC2_TXD[5]/DR_UTMI_OPMODE1
U28
O
OVDD
TSEC2_TXD[4]/DR_UTMI_OPMODE0
U27
O
OVDD
TSEC2_TXD[3:0]/GPIO1[17:20]
AB26, AB27, AA24, AB28
I/O
LVDD2
TSEC2_TX_ER/GPIO1[24]
R27
I/O
OVDD
TSEC2_TX_EN/GPIO1[12]
AD28
I/O
LVDD2
TSEC2_TX_CLK/GPIO1[30]
R26
I/O
OVDD
3
DUART
UART_SOUT[1:2]/
MSRCID[0:1]/LSRCID[0:1]
B4, A4
O
OVDD
UART_SIN[1:2]/
MSRCID[2:3]/LSRCID[2:3]
D5, C5
I/O
OVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
79
Table 55. MPC8347EA (PBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
UART_CTS[1]/
MSRCID4/LSRCID4
B5
I/O
OVDD
UART_CTS[2]/
MDVAL/ LDVAL
A5
I/O
OVDD
UART_RTS[1:2]
D6, C6
O
OVDD
Notes
I2C interface
IIC1_SDA
E5
I/O
OVDD
2
IIC1_SCL
A6
I/O
OVDD
2
IIC2_SDA
B6
I/O
OVDD
2
IIC2_SCL
E7
I/O
OVDD
2
SPI
SPIMOSI/LCS[6]
D7
I/O
OVDD
SPIMISO/LCS[7]
C7
I/O
OVDD
SPICLK
B7
I/O
OVDD
SPISEL
A7
I
OVDD
Clocks
PCI_CLK_OUT[0:2]
Y1, W3, W2
O
OVDD
PCI_CLK_OUT[3]/LCS[6]
W1
O
OVDD
PCI_CLK_OUT[4]/LCS[7]
V3
O
OVDD
PCI_SYNC_IN/PCI_CLOCK
U4
I
OVDD
PCI_SYNC_OUT
U5
O
OVDD
RTC/PIT_CLOCK
E9
I
OVDD
CLKIN
W5
I
OVDD
3
JTAG
TCK
H27
I
OVDD
TDI
H28
I
OVDD
4
TDO
M24
O
OVDD
3
TMS
J27
I
OVDD
4
TRST
K26
I
OVDD
4
Test
TEST
F28
I
OVDD
6
TEST_SEL
T3
I
OVDD
6
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
80
Freescale Semiconductor
Table 55. MPC8347EA (PBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
O
OVDD
Notes
PMC
K27
QUIESCE
System Control
PORESET
K28
I
OVDD
HRESET
M25
I/O
OVDD
1
SRESET
L27
I/O
OVDD
2
I
—
8
Thermal Management
THERM0
B15
Power and Ground Signals
AVDD1
C15
Power for
e300 PLL
(1.2 V)
AVDD1
AVDD2
U1
Power for
system PLL
(1.2 V)
AVDD2
AVDD3
AF9
Power for
DDR DLL
(1.2 V)
—
AVDD4
U2
Power for
LBIU DLL
(1.2 V)
AVDD4
GND
A2, B1, B2, D10, D18, E6, E14, E22, F9,
F12, F15, F18, F21, F24, G5, H6, J23, L4,
L6, L12, L13, L14, L15, L16, L17, M11, M12,
M13, M14, M15, M16, M17, M18, M23, N11,
N12, N13, N14, N15, N16, N17, N18, P6,
P11, P12, P13, P14, P15, P16, P17, P18,
P24, R5, R11, R12, R13, R14, R15, R16,
R17, R18, R23, T11, T12, T13, T14, T15,
T16, T17, T18, U6, U11, U12, U13, U14,
U15, U16, U17, U18, V12, V13, V14, V15,
V16, V17, V23, V25, W4, Y6, AA23, AB24,
AC5, AC8, AC11, AC14, AC17, AC20, AD9,
AD15, AD21, AE12, AE18, AF3, AF26
—
—
GVDD
U9, V9, W10, W19, Y11, Y12, Y14, Y15,
Y17, Y18, AA6, AB5, AC9, AC12, AC15,
AC18, AC21, AC24, AD6, AD8, AD14,
AD20, AE5, AE11, AE17, AG2, AG27
Power for
DDR DRAM
I/O Voltage
(2.5 V)
GVDD
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
81
Table 55. MPC8347EA (PBGA) Pinout Listing (continued)
Signal
Package Pin Number
Pin Type
Power
Supply
LVDD1
U20, W25
Power for
Three Speed
Ethernet #1
and for
Ethernet
Management
Interface I/O
(2.5V, 3.3V)
LVDD1
LVDD2
V20, Y23
Power for
Three Speed
Ethernet #2
I/O (2.5V,
3.3V)
LVDD2
VDD
J11, J12, J15, K10, K11, K12, K13, K14,
K15, K16, K17, K18, K19, L10, L11, L18,
L19, M10, M19, N10, N19, P9, P10, P19,
R10, R19, R20, T10, T19, U10, U19, V10,
V11, V18, V19, W11, W12, W13, W14, W15,
W16, W17, W18
Power for
Core
(1.2 V)
VDD
OVDD
B27, D3, D11, D19, E15, E23, F5, F8, F11, PCI, 10/100
F14, F17, F20, G24, H23, H24, J6, J14, J17, Ethernet, and
J18, K4, L9, L20, L23, L25, M6, M9, M20,
other
P5, P20, P23, R6, R9, R24, U23, V4, V6
Standard
(3.3 V)
MVREF1
AF19
I
DDR
Reference
Voltage
MVREF2
AE10
I
DDR
Reference
Voltage
Notes
OVDD
No Connection
NC
V1, V2, V5
Notes:
1. This pin is an open-drain signal. A weak pull-up resistor (1 kΩ) should be placed on this pin to OVDD
2. This pin is an open-drain signal. A weak pull-up resistor (2–10 kΩ) should be placed on this pin to OVDD.
3. During reset, this output is actively driven rather than three-stated.
4. These JTAG pins have weak internal pull-up P-FETs that are always enabled.
5. This pin should have a weak pull-up if the chip is in PCI host mode. Follow the PCI specifications.
6. .This pin must always be tied to GND
7. This pin must always be left not connected
8. Thermal sensitive resistor.
9. It is recommended that MDIC0 be tied to GRD using an 18 Ω resistor and MDIC1 be tied to DDR power using an 18 Ω
resistor.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
82
Freescale Semiconductor
Clocking
19 Clocking
Figure 40 shows the internal distribution of the clocks.
MPC8347EA
e300 core
Core PLL
csb_clk
to DDR
memory
controller
ddr_clk
System PLL
Clock
Unit lbiu_clk
core_clk
DDR
Clock
Div
/2
6
6
/n
MCK[0:5]
MCK[0:5]
DDR
Memory
Device
LCLK[0:2]
to local bus
memory
LBIU
controller
DLL
LSYNC_OUT
Local Bus
Memory
Device
LSYNC_IN
csb_clk to rest
of the device
PCI_CLK/
PCI_SYNC_IN
CFG_CLKIN_DIV
CLKIN
PCI_SYNC_OUT
PCI Clock
Divider
5
PCI_CLK_OUT[0:4]
Figure 40. MPC8347EA Clock Subsystem
The primary clock source can be one of two inputs, CLKIN or PCI_CLK, depending on whether the device
is configured in PCI host or PCI agent mode. When the MPC8347EA is configured as a PCI host device,
CLKIN is its primary input clock. CLKIN feeds the PCI clock divider (÷2) and the multiplexors for
PCI_SYNC_OUT and PCI_CLK_OUT. The CFG_CLKIN_DIV configuration input selects whether
CLKIN or CLKIN/2 is driven out on the PCI_SYNC_OUT signal. The OCCR[PCICDn] parameters select
whether CLKIN or CLKIN/2 is driven out on the PCI_CLK_OUTn signals.
PCI_SYNC_OUT is connected externally to PCI_SYNC_IN to allow the internal clock subsystem to
synchronize to the system PCI clocks. PCI_SYNC_OUT must be connected properly to PCI_SYNC_IN,
with equal delay to all PCI agent devices in the system, to allow the MPC8347EA to function. When the
MPC8347EA is configured as a PCI agent device, PCI_CLK is the primary input clock and the CLKIN
signal should be tied to GND.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
83
Clocking
As shown in Figure 40, the primary clock input (frequency) is multiplied up by the system phase-locked
loop (PLL) and the clock unit to create the coherent system bus clock (csb_clk), the internal clock for the
DDR controller (ddr_clk), and the internal clock for the local bus interface unit (lbiu_clk).
The csb_clk frequency is derived from a complex set of factors that can be simplified into the following
equation:
csb_clk = {PCI_SYNC_IN × (1 + CFG_CLKIN_DIV)} × SPMF
In PCI host mode, PCI_SYNC_IN × (1 + CFG_CLKIN_DIV) is the CLKIN frequency.
The csb_clk serves as the clock input to the e300 core. A second PLL inside the e300 core multiplies the
csb_clk frequency to create the internal clock for the e300 core (core_clk). The system and core PLL
multipliers are selected by the SPMF and COREPLL fields in the reset configuration word low (RCWL),
which is loaded at power-on reset or by one of the hard-coded reset options. See the chapter on reset,
clocking, and initialization in the MPC8349EA Reference Manual for more information on the clock
subsystem.
The internal ddr_clk frequency is determined by the following equation:
ddr_clk = csb_clk × (1 + RCWL[DDRCM])
ddr_clk is not the external memory bus frequency; ddr_clk passes through the DDR clock divider (÷2) to
create the differential DDR memory bus clock outputs (MCK and MCK). However, the data rate is the
same frequency as ddr_clk.
The internal lbiu_clk frequency is determined by the following equation:
lbiu_clk = csb_clk × (1 + RCWL[LBIUCM])
lbiu_clk is not the external local bus frequency; lbiu_clk passes through the LBIU clock divider to create
the external local bus clock outputs (LSYNC_OUT and LCLK[0:2]). The LBIU clock divider ratio is
controlled by LCCR[CLKDIV].
In addition, some of the internal units may have to be shut off or operate at lower frequency than the
csb_clk frequency. Those units have a default clock ratio that can be configured by a memory-mapped
register after the device exits reset. Table 56 specifies which units have a configurable clock frequency.
Table 56. Configurable Clock Units
Unit
Default
Frequency
Options
csb_clk/3
Off, csb_clk, csb_clk/2, csb_clk/3
I2C1
csb_clk/3
Off, csb_clk, csb_clk/2, csb_clk/3
Security Core
csb_clk/3
Off, csb_clk, csb_clk/2, csb_clk/3
USB DR, USB MPH
csb_clk/3
Off, csb_clk, csb_clk/2, csb_clk/3
TSEC1
TSEC2,
PCI and DMA complex
csb_clk
Off, csb_clk
Table 57 provides the operating frequencies for the MPC8347EA TBGA under recommended operating
conditions (see Table 2).
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
84
Freescale Semiconductor
Clocking
Table 57. Operating Frequencies for TBGA
Characteristic 1
533 MHz
667 MHz
Unit
e300 core frequency (core_clk)
266–533
266–667
MHz
Coherent system bus frequency
(csb_clk)
100–266
100–333
MHz
DDR and DDR2 memory bus frequency
(MCLK) 2
100–200
100–200
MHz
16.67–133
16.67–133
MHz
25–66
25–66
MHz
Security core maximum internal operating frequency
133
166
MHz
USB_DR, USB_MPH maximum internal operating frequency
133
166
MHz
Local bus frequency
(LCLKn) 3
PCI input frequency (CLKIN or PCI_CLK)
1
The CLKIN frequency, RCWL[SPMF], and RCWL[COREPLL] settings must be chosen so that the resulting csb_clk, MCLK,
LCLK[0:2], and core_clk frequencies do not exceed their respective maximum or minimum operating frequencies. The value
of SCCR[ENCCM], SCCR[USBDRCM]and SCCR[USBMPHCM] must be programmed so that the maximum internal operating
frequency of the Security core and USB modules does not exceed the respective values listed in this table.
2 The DDR data rate is 2x the DDR memory bus frequency.
3 The local bus frequency is 1/2, 1/4, or 1/8 of the lbiu_clk frequency (depending on LCCR[CLKDIV]) which is in turn 1x or 2x
the csb_clk frequency (depending on RCWL[LBIUCM]).
Table 58 provides the operating frequencies for the MPC8347EA PBGA under recommended operating
conditions.
Table 58. Operating Frequencies for PBGA
Characteristic 1
e300 core frequency (core_clk)
266 MHz
333 MHz
400 MHz
Unit
200–266
200–333
200–400
MHz
Coherent system bus frequency (csb_clk)
100–266
MHz
DDR memory bus frequency (MCLK) 2
100–133
MHz
16.67–133
MHz
25–66
MHz
Security core maximum internal operating frequency
133
MHz
USB_DR, USB_MPH maximum internal operating
frequency
133
MHz
Local bus frequency (LCLKn) 3
PCI input frequency (CLKIN or PCI_CLK)
1
The CLKIN frequency, RCWL[SPMF], and RCWL[COREPLL] settings must be chosen so that the resulting csb_clk, MCLK,
LCLK[0:2], and core_clk frequencies do not exceed their respective maximum or minimum operating frequencies. The value
of SCCR[ENCCM], SCCR[USBDRCM]and SCCR[USBMPHCM] must be programmed so that the maximum internal operating
frequency of the Security core and USB modules does not exceed the respective values listed in this table.
2
The DDR data rate is 2x the DDR memory bus frequency.
3 The local bus frequency is 1/2, 1/4, or 1/8 of the lbiu_clk frequency (depending on LCCR[CLKDIV]) which is in turn 1x or 2x
the csb_clk frequency (depending on RCWL[LBIUCM]).
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
85
Clocking
19.1
System PLL Configuration
The system PLL is controlled by the RCWL[SPMF] parameter. Table 59 shows the multiplication factor
encodings for the system PLL.
Table 59. System PLL Multiplication Factors
RCWL[SPMF]
System PLL Multiplication
Factor
0000
× 16
0001
Reserved
0010
×2
0011
×3
0100
×4
0101
×5
0110
×6
0111
×7
1000
×8
1001
×9
1010
× 10
1011
× 11
1100
× 12
1101
× 13
1110
× 14
1111
× 15
As described in Section 19, “Clocking,” The LBIUCM, DDRCM, and SPMF parameters in the reset
configuration word low and the CFG_CLKIN_DIV configuration input signal select the ratio between the
primary clock input (CLKIN or PCI_CLK) and the internal coherent system bus clock (csb_clk). Table 60
and Table 61 show the expected frequency values for the CSB frequency for select csb_clk to
CLKIN/PCI_SYNC_IN ratios.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
86
Freescale Semiconductor
Clocking
Table 60. CSB Frequency Options for Host Mode
Input Clock Frequency (MHz)2
CFG_CLKIN_DIV
at reset 1
SPMF
csb_clk :
Input Clock
Ratio 2
16.67
25
33.33
66.67
csb_clk Frequency (MHz)
1
2
Low
0010
2:1
Low
0011
3:1
Low
0100
4:1
Low
0101
5:1
Low
0110
6:1
Low
0111
Low
133
100
200
100
133
266
125
166
333
100
150
200
7:1
116
175
233
1000
8:1
133
200
266
Low
1001
9:1
150
225
300
Low
1010
10 : 1
166
250
333
Low
1011
11 : 1
183
275
Low
1100
12 : 1
200
300
Low
1101
13 : 1
216
325
Low
1110
14 : 1
233
Low
1111
15 : 1
250
Low
0000
16 : 1
266
High
0010
2:1
High
0011
3:1
100
200
High
0100
4:1
133
266
High
0101
5:1
166
333
High
0110
6:1
200
High
0111
7:1
233
High
1000
8:1
133
CFG_CLKIN_DIV selects the ratio between CLKIN and PCI_SYNC_OUT.
CLKIN is the input clock in host mode; PCI_CLK is the input clock in agent mode.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
87
Clocking
Table 61. CSB Frequency Options for Agent Mode
Input Clock Frequency (MHz)2
CFG_CLKIN_DIV
at reset 1
SPMF
csb_clk :
Input Clock
Ratio 2
16.67
25
33.33
66.67
csb_clk Frequency (MHz)
1
2
19.2
Low
0010
2:1
Low
0011
3:1
Low
0100
4:1
Low
0101
5:1
Low
0110
6:1
Low
0111
Low
133
100
200
100
133
266
125
166
333
100
150
200
7:1
116
175
233
1000
8:1
133
200
266
Low
1001
9:1
150
225
300
Low
1010
10 : 1
166
250
333
Low
1011
11 : 1
183
275
Low
1100
12 : 1
200
300
Low
1101
13 : 1
216
325
Low
1110
14 : 1
233
Low
1111
15 : 1
250
Low
0000
16 : 1
266
high
0010
4:1
High
0011
6:1
High
0100
High
100
133
100
150
200
8:1
133
200
266
0101
10 : 1
166
250
333
High
0110
12 : 1
200
300
High
0111
14 : 1
233
High
1000
16 : 1
266
266
CFG_CLKIN_DIV doubles csb_clk if set high.
CLKIN is the input clock in host mode; PCI_CLK is the input clock in agent mode.
Core PLL Configuration
RCWL[COREPLL] selects the ratio between the internal coherent system bus clock (csb_clk) and the e300
core clock (core_clk). Table 62 shows the encodings for RCWL[COREPLL]. COREPLL values that are
not listed in Table 62 should be considered as reserved.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
88
Freescale Semiconductor
Clocking
NOTE
Core VCO frequency = Core frequency × VCO divider
VCO divider must be set properly so that the core VCO frequency is in the
range of 800–1800 MHz.
Table 62. e300 Core PLL Configuration
RCWL[COREPLL]
1
core_clk : csb_clk Ratio
VCO divider 1
0–1
2–5
6
nn
0000
n
PLL bypassed
(PLL off, csb_clk clocks core directly)
PLL bypassed
(PLL off, csb_clk clocks core directly)
00
0001
0
1:1
2
01
0001
0
1:1
4
10
0001
0
1:1
8
11
0001
0
1:1
8
00
0001
1
1.5:1
2
01
0001
1
1.5:1
4
10
0001
1
1.5:1
8
11
0001
1
1.5:1
8
00
0010
0
2:1
2
01
0010
0
2:1
4
10
0010
0
2:1
8
11
0010
0
2:1
8
00
0010
1
2.5:1
2
01
0010
1
2.5:1
4
10
0010
1
2.5:1
8
11
0010
1
2.5:1
8
00
0011
0
3:1
2
01
0011
0
3:1
4
10
0011
0
3:1
8
11
0011
0
3:1
8
Core VCO frequency = Core frequency × VCO divider. The VCO divider must be set properly so that the core VCO frequency
is in the range of 800–1800 MHz.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
89
Clocking
19.3
Suggested PLL Configurations
Table 63 shows suggested PLL configurations for 33 MHz and 66 MHz input clocks.
Table 63. Suggested PLL Configurations
Ref
No. 1
RCWL
SPMF
CORE
PLL
400 MHz Device
Input
Clock
Freq
(MHz) 2
CSB
Freq
(MHz)
533 MHz Device
Core
Freq
(MHz)
Input
Clock
Freq
(MHz)2
CSB
Freq
(MHz)
667 MHz Device
Core
Freq
(MHz)
Input
Clock
Freq
(MHz)2
CSB
Freq
(MHz)
Core
Freq
(MHz)
33 MHz CLKIN/PCI_CLK Options
922
1001
0100010
—
—
—
—
—
300
33
300
300
723
0111
0100011
33
233
350
33
233
350
33
233
350
604
0110
0000100
33
200
400
33
200
400
33
200
400
624
0110
0100100
33
200
400
33
200
400
33
200
400
803
1000
0000011
33
266
400
33
266
400
33
266
400
823
1000
0100011
33
266
400
33
266
400
33
266
400
903
1001
0000011
—
—
33
300
450
923
1001
0100011
—
—
33
300
450
704
0111
0000011
—
33
233
466
33
233
466
724
0111
0100011
—
33
233
466
33
233
466
804
1000
0000100
—
33
266
533
33
266
533
705
0111
0000101
—
—
33
233
583
606
0110
0000110
—
—
33
200
600
904
1001
0000100
—
—
33
300
600
805
1000
0000101
—
—
33
266
667
A04
1010
0000100
—
—
33
333
667
66 MHz CLKIN/PCI_CLK Options
304
0011
0000100
66
200
400
66
200
400
66
200
400
324
0011
0100100
66
200
400
66
200
400
66
200
400
403
0100
0000011
66
266
400
66
266
400
66
266
400
423
0100
0100011
66
266
400
66
266
400
66
266
400
305
0011
0000101
—
66
200
500
66
200
500
404
0100
0000100
—
66
266
533
66
266
533
306
0011
0000100
—
—
66
200
600
405
0100
0000101
—
—
66
266
667
504
0101
0000100
—
—
66
333
667
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
90
Freescale Semiconductor
Clocking
1
The PLL configuration reference number is the hexadecimal representation of RCWL, bits 4–15 associated with the SPMF
and COREPLL settings given in the table.
2
The input clock is CLKIN for PCI host mode or PCI_CLK for PCI agent mode.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
91
Thermal
20 Thermal
This section describes the thermal specifications of the MPC8347EA.
20.1
Thermal Characteristics
Table 64 provides the package thermal characteristics for the 672 35 × 35 mm TBGA of the MPC8347EA.
Table 64. Package Thermal Characteristics for TBGA
Characteristic
Symbol
Value
Unit
Notes
Junction-to-ambient natural convection on single-layer board (1s)
RθJA
14
°C/W
1, 2
Junction-to-ambient natural convection on four-layer board (2s2p)
RθJMA
11
°C/W
1, 3
Junction-to-ambient (@200 ft/min) on single-layer board (1s)
RθJMA
11
°C/W
1, 3
Junction-to-ambient (@ 200 ft/min) on four-layer board (2s2p)
RθJMA
8
•C/W
1, 3
Junction-to-ambient (@ 2 m/s) on single-layer board (1s)
RθJMA
9
•C/W
1, 3
Junction-to-ambient (@ 2 m/s) on four-layer board (2s2p)
RθJMA
7
•C/W
1, 3
Junction-to-board thermal
RθJB
3.8
•C/W
4
Junction-to-case thermal
RθJC
1.7
•C/W
5
Junction-to-package natural convection on top
ψJT
1
•C/W
6
Notes
1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal
resistance.
2. Per SEMI G38-87 and JEDEC JESD51-2 with the single layer board horizontal.
3. Per JEDEC JESD51-6 with the board horizontal, 1 m/s is approximately equal to 200 linear feet per minute (LFM).
4. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on
the top surface of the board near the package.
5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method
1012.1).
6. Thermal characterization parameter indicating the temperature difference between package top and the junction temperature
per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT.
Table 65 provides the package thermal characteristics for the 620 29 × 29 mm PBGA of the MPC8347EA.
Table 65. Package Thermal Characteristics for PBGA
Characteristic
Symbol
Value
Unit
Notes
Junction-to-ambient natural convection on single layer board (1s)
RθJA
21
°C/W
1, 2
Junction-to-ambient natural convection on four layer board (2s2p)
RθJMA
15
°C/W
1, 3
Junction-to-ambient (@200 ft/min) on single layer board (1s)
RθJMA
17
°C/W
1, 3
Junction-to-ambient (@ 200 ft/min) on four layer board (2s2p)
RθJMA
12
•C/W
1, 3
Junction-to-board thermal
RθJB
6
•C/W
4
Junction-to-case thermal
RθJC
5
•C/W
5
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
92
Freescale Semiconductor
Thermal
Table 65. Package Thermal Characteristics for PBGA (continued)
Characteristic
Junction-to-package natural convection on top
Symbol
Value
Unit
Notes
ψJT
5
•C/W
6
Notes
1. Junction temperature is a function of die size, on-chip power dissipation, package thermal resistance, mounting site (board)
temperature, ambient temperature, air flow, power dissipation of other components on the board, and board thermal
resistance.
2. Per SEMI G38-87 and JEDEC JESD51-2 with the single layer board horizontal.
3. Per JEDEC JESD51-6 with the board horizontal.
4. Thermal resistance between the die and the printed circuit board per JEDEC JESD51-8. Board temperature is measured on
the top surface of the board near the package.
5. Thermal resistance between the die and the case top surface as measured by the cold plate method (MIL SPEC-883 Method
1012.1).
6. Thermal characterization parameter indicating the temperature difference between package top and the junction temperature
per JEDEC JESD51-2. When Greek letters are not available, the thermal characterization parameter is written as Psi-JT.
20.2
Thermal Management Information
For the following sections, PD = (VDD × IDD) + PI/O where PI/O is the power dissipation of the I/O drivers.
See Table 5 for I/O power dissipation values.
20.2.1
Estimation of Junction Temperature with Junction-to-Ambient
Thermal Resistance
An estimation of the chip junction temperature, TJ, can be obtained from the equation:
TJ = TA + (RθJA × PD)
where:
TJ = junction temperature (°C)
TA = ambient temperature for the package (°C)
RθJA = junction to ambient thermal resistance (°C/W)
PD = power dissipation in the package (W)
The junction to ambient thermal resistance is an industry-standard value that provides a quick and easy
estimation of thermal performance. Generally, the value obtained on a single layer board is appropriate for
a tightly packed printed circuit board. The value obtained on the board with the internal planes is usually
appropriate if the board has low power dissipation and the components are well separated. Test cases have
demonstrated that errors of a factor of two (in the quantity TJ - TA) are possible.
20.2.2
Estimation of Junction Temperature with Junction-to-Board
Thermal Resistance
The thermal performance of a device cannot be adequately predicted from the junction to ambient thermal
resistance. The thermal performance of any component is strongly dependent on the power dissipation of
surrounding components. In addition, the ambient temperature varies widely within the application. For
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
93
Thermal
many natural convection and especially closed box applications, the board temperature at the perimeter
(edge) of the package is approximately the same as the local air temperature near the device. Specifying
the local ambient conditions explicitly as the board temperature provides a more precise description of the
local ambient conditions that determine the temperature of the device.
At a known board temperature, the junction temperature is estimated using the following equation:
TJ = TA + (RθJA × PD)
where:
TA = ambient temperature for the package (°C)
RθJA = junction to ambient thermal resistance (°C/W)
PD = power dissipation in the package (W)
When the heat loss from the package case to the air can be ignored, acceptable predictions of junction
temperature can be made. The application board should be similar to the thermal test condition: the
component is soldered to a board with internal planes.
20.2.3
Experimental Determination of Junction Temperature
To determine the junction temperature of the device in the application after prototypes are available, use
the thermal characterization parameter (ΨJT) to determine the junction temperature and a measure of the
temperature at the top center of the package case using the following equation:
TJ = TT + (ΨJT × PD)
where:
TJ = junction temperature (°C)
TT = thermocouple temperature on top of package (°C)
ΨJT = junction to ambient thermal resistance (°C/W)
PD = power dissipation in the package (W)
The thermal characterization parameter is measured per the JESD51-2 specification using a 40 gauge type
T thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so
that the thermocouple junction rests on the package. A small amount of epoxy is placed over the
thermocouple junction and over about 1 mm of wire extending from the junction. The thermocouple wire
is placed flat against the package case to avoid measurement errors caused by cooling effects of the
thermocouple wire.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
94
Freescale Semiconductor
Thermal
20.2.4
Heat Sinks and Junction-to-Case Thermal Resistance
Some application environments require a heat sink to provide the necessary thermal management of the
device. When a heat sink is used, the thermal resistance is expressed as the sum of a junction to case
thermal resistance and a case-to-ambient thermal resistance:
RθJA = RθJC + RθCA
where:
RθJA = junction to ambient thermal resistance (°C/W)
RθJC = junction to case thermal resistance (°C/W)
RθCA = case to ambient thermal resistance (°C/W)
RθJC is device-related and cannot be influenced by the user. The user controls the thermal environment to
change the case to ambient thermal resistance, RθCA. For instance, the user can change the size of the heat
sink, the air flow around the device, the interface material, the mounting arrangement on printed circuit
board, or change the thermal dissipation on the printed circuit board surrounding the device.
The thermal performance of devices with heat sinks has been simulated with a few commercially available
heat sinks. The heat sink choice is determined by the application environment (temperature, air flow,
adjacent component power dissipation) and the physical space available. Because there is not a standard
application environment, a standard heat sink is not required.
Table 66 and Table 67 show heat sink thermal resistance for TBGA and PBGA of the MPC8347EA.
Table 66. Heat Sink and Thermal Resistance of MPC8347EA (TBGA)
35 × 35 mm TBGA
Heat Sink Assuming Thermal Grease
Air Flow
Thermal Resistance
AAVID 30 × 30 × 9.4 mm Pin Fin
Natural Convection
10
AAVID 30 × 30 × 9.4 mm Pin Fin
1 m/s
6.5
AAVID 30 × 30 × 9.4 mm Pin Fin
2 m/s
5.6
AAVID 31 × 35 × 23 mm Pin Fin
Natural Convection
8.4
AAVID 31 × 35 × 23 mm Pin Fin
1 m/s
4.7
AAVID 31 × 35 × 23 mm Pin Fin
2 m/s
4
Wakefield, 53 × 53 × 25 mm Pin Fin
Natural Convection
5.7
Wakefield, 53 × 53 × 25 mm Pin Fin
1 m/s
3.5
Wakefield, 53 × 53 × 25 mm Pin Fin
2 m/s
2.7
MEI, 75 × 85 × 12 no adjacent board, extrusion
Natural Convection
6.7
MEI, 75 × 85 × 12 no adjacent board, extrusion
1 m/s
4.1
MEI, 75 × 85 × 12 no adjacent board, extrusion
2 m/s
2.8
MEI, 75 × 85 × 12 mm, adjacent board, 40 mm Side bypass
1 m/s
3.1
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
95
Thermal
f
Table 67. Heat Sink and Thermal Resistance of MPC8347EA (PBGA)
29 × 29 mm PBGA
Heat Sink Assuming Thermal Grease
Air Flow
Thermal Resistance
AAVID 30 × 30 × 9.4 mm Pin Fin
Natural Convection
13.5
AAVID 30 × 30 × 9.4 mm Pin Fin
1 m/s
9.6
AAVID 30 × 30 × 9.4 mm Pin Fin
2 m/s
8.8
AAVID 31 × 35 × 23 mm Pin Fin
Natural Convection
11.3
AAVID 31 × 35 × 23 mm Pin Fin
1 m/s
8.1
AAVID 31 × 35 × 23 mm Pin Fin
2 m/s
7.5
Wakefield, 53 × 53 × 25 mm Pin Fin
Natural Convection
9.1
Wakefield, 53 × 53 × 25 mm Pin Fin
1 m/s
7.1
Wakefield, 53 × 53 × 25 mm Pin Fin
2 m/s
6.5
MEI, 75 × 85 × 12 no adjacent board, extrusion
Natural Convection
10.1
MEI, 75 × 85 × 12 no adjacent board, extrusion
1 m/s
7.7
MEI, 75 × 85 × 12 no adjacent board, extrusion
2 m/s
6.6
MEI, 75 × 85 × 12 mm, adjacent board, 40 mm Side bypass
1 m/s
6.9
Accurate thermal design requires thermal modeling of the application environment using computational
fluid dynamics software which can model both the conduction cooling and the convection cooling of the
air moving through the application. Simplified thermal models of the packages can be assembled using the
junction-to-case and junction-to-board thermal resistances listed in the thermal resistance table. More
detailed thermal models can be made available on request.
Heat sink vendors include the following list:
Aavid Thermalloy
80 Commercial St.
Concord, NH 03301
Internet: www.aavidthermalloy.com
603-224-9988
Alpha Novatech
473 Sapena Ct. #12
Santa Clara, CA 95054
Internet: www.alphanovatech.com
408-567-8082
International Electronic Research Corporation (IERC)
413 North Moss St.
Burbank, CA 91502
Internet: www.ctscorp.com
818-842-7277
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
96
Freescale Semiconductor
Thermal
Millennium Electronics (MEI)
Loroco Sites
671 East Brokaw Road
San Jose, CA 95112
Internet: www.mei-thermal.com
408-436-8770
Tyco Electronics
Chip Coolers™
P.O. Box 3668
Harrisburg, PA 17105-3668
Internet: www.chipcoolers.com
800-522-2800
Wakefield Engineering
33 Bridge St.
Pelham, NH 03076
Internet: www.wakefield.com
603-635-5102
Interface material vendors include the following:
20.3
Chomerics, Inc.
77 Dragon Ct.
Woburn, MA 01801
Internet: www.chomerics.com
781-935-4850
Dow-Corning Corporation
Dow-Corning Electronic Materials
P.O. Box 994
Midland, MI 48686-0997
Internet: www.dowcorning.com
800-248-2481
Shin-Etsu MicroSi, Inc.
10028 S. 51st St.
Phoenix, AZ 85044
Internet: www.microsi.com
888-642-7674
The Bergquist Company
18930 West 78th St.
Chanhassen, MN 55317
Internet: www.bergquistcompany.com
800-347-4572
Heat Sink Attachment
When heat sinks are attached, an interface material is required, preferably thermal grease and a spring clip.
The spring clip should connect to the printed circuit board, either to the board itself, to hooks soldered to
the board, or to a plastic stiffener. Avoid attachment forces that can lift the edge of the package or peel the
package from the board. Such peeling forces reduce the solder joint lifetime of the package. The
recommended maximum force on the top of the package is 10 lb force (4.5 kg force). Any adhesive
attachment should attach to painted or plastic surfaces, and its performance should be verified under the
application requirements.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
97
Thermal
20.3.1
Experimental Determination of the Junction Temperature with a
Heat Sink
When a heat sink is used, the junction temperature is determined from a thermocouple inserted at the
interface between the case of the package and the interface material. A clearance slot or hole is normally
required in the heat sink. Minimize the size of the clearance to minimize the change in thermal
performance caused by removing part of the thermal interface to the heat sink. Because of the experimental
difficulties with this technique, many engineers measure the heat sink temperature and then back calculate
the case temperature using a separate measurement of the thermal resistance of the interface. From this
case temperature, the junction temperature is determined from the junction to case thermal resistance.
TJ = TC + (RθJC × PD)
where:
TJ = junction temperature (°C)
TC = case temperature of the package (°C)
RθJC = junction to case thermal resistance (°C/W)
PD = power dissipation (W)
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
98
Freescale Semiconductor
System Design Information
21 System Design Information
This section provides electrical and thermal design recommendations for successful application of the
MPC8347EA.
21.1
System Clocking
The MPC8347EA includes two PLLs.
1. The platform PLL (AVDD1) generates the platform clock from the externally supplied CLKIN
input. The frequency ratio between the platform and CLKIN is selected using the platform PLL
ratio configuration bits as described in Section 19.1, “System PLL Configuration.”
2. The e300 Core PLL (AVDD2) generates the core clock as a slave to the platform clock. The
frequency ratio between the e300 core clock and the platform clock is selected using the e300
PLL ratio configuration bits as described in Section 19.2, “Core PLL Configuration.”
21.2
PLL Power Supply Filtering
Each PLL gets power through independent power supply pins (AVDD1, AVDD2 respectively). The AVDD
level should always equal to VDD, and preferably these voltages are derived directly from VDD through a
low frequency filter scheme.
There are a number of ways to provide power reliably to the PLLs, but the recommended solution is to
provide five independent filter circuits as illustrated in Figure 41, one to each of the five AVDD pins.
Independent filters to each PLL reduce the opportunity to cause noise injection from one PLL to the other.
The circuit filters noise in the PLL resonant frequency range from 500 kHz to 10 MHz. It should be built
with surface mount capacitors with minimum effective series inductance (ESL). Consistent with the
recommendations of Dr. Howard Johnson in High Speed Digital Design: A Handbook of Black Magic
(Prentice Hall, 1993), multiple small capacitors of equal value are recommended over a single large value
capacitor.
To minimize noise coupled from nearby circuits, each circuit should be placed as closely as possible to the
specific AVDD pin being supplied. It should be possible to route directly from the capacitors to the AVDD
pin, which is on the periphery of package, without the inductance of vias.
Figure 41 shows the PLL power supply filter circuit.
10 Ω
VDD
AVDD (or L2AVDD)
2.2 µF
2.2 µF
GND
Low ESL Surface Mount Capacitors
Figure 41. PLL Power Supply Filter Circuit
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
99
System Design Information
21.3
Decoupling Recommendations
Due to large address and data buses and high operating frequencies, the MPC8347EA can generate
transient power surges and high frequency noise in its power supply, especially while driving large
capacitive loads. This noise must be prevented from reaching other components in the MPC8347EA
system, and the MPC8347EA itself requires a clean, tightly regulated source of power. Therefore, the
system designer should place at least one decoupling capacitor at each VDD, OVDD, GVDD, and LVDD pin
of the MPC8347EA. These capacitors should receive their power from separate VDD, OVDD, GVDD,
LVDD, and GND power planes in the PCB, with short traces to minimize inductance. Capacitors can be
placed directly under the device using a standard escape pattern. Others can surround the part.
These capacitors should have a value of 0.01 or 0.1 µF. Only ceramic SMT (surface mount technology)
capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes.
In addition, distribute several bulk storage capacitors around the PCB, feeding the VDD, OVDD, GVDD,
and LVDD planes, to enable quick recharging of the smaller chip capacitors. These bulk capacitors should
have a low ESR (equivalent series resistance) rating to ensure the quick response time. They should also
be connected to the power and ground planes through two vias to minimize inductance. Suggested bulk
capacitors are 100–330 µF (AVX TPS tantalum or Sanyo OSCON).
21.4
Connection Recommendations
To ensure reliable operation, connect unused inputs to an appropriate signal level. Unused active low
inputs should be tied to OVDD, GVDD, or LVDD as required. Unused active high inputs should be
connected to GND. All NC (no-connect) signals must remain unconnected.
Power and ground connections must be made to all external VDD, GVDD, LVDD, OVDD, and GND pins of
the MPC8347EA.
21.5
Output Buffer DC Impedance
The MPC8347EA drivers are characterized over process, voltage, and temperature. For all buses, the
driver is a push-pull single-ended driver type (open drain for I2C).
To measure Z0 for the single-ended drivers, an external resistor is connected from the chip pad to OVDD
or GND. Then the value of each resistor is varied until the pad voltage is OVDD/2 (see Figure 42). The
output impedance is the average of two components, the resistances of the pull-up and pull-down devices.
When data is held high, SW1 is closed (SW2 is open) and RP is trimmed until the voltage at the pad equals
OVDD/2. RP then becomes the resistance of the pull-up devices. RP and RN are designed to be close to each
other in value. Then, Z0 = (RP + RN)/2.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
100
Freescale Semiconductor
System Design Information
OVDD
RN
SW2
Pad
Data
SW1
RP
OGND
Figure 42. Driver Impedance Measurement
Two measurements give the value of this resistance and the strength of the driver current source. First, the
output voltage is measured while driving logic 1 without an external differential termination resistor. The
measured voltage is V1 = Rsource × Isource. Second, the output voltage is measured while driving logic 1
with an external precision differential termination resistor of value Rterm. The measured voltage is
V2 = (1/(1/R1 + 1/R2)) × Isource. Solving for the output impedance gives Rsource = Rterm × (V1/V2 – 1). The
drive current is then Isource = V1/Rsource.
Table 68 summarizes the signal impedance targets. The driver impedance are targeted at minimum VDD,
nominal OVDD, 105°C.
Table 68. Impedance Characteristics
Impedance
Local Bus, Ethernet,
DUART, Control,
Configuration, Power
Management
PCI Signals
(not including PCI
output clocks)
PCI Output Clocks
(including
PCI_SYNC_OUT)
DDR DRAM
Symbol
Unit
RN
42 Target
25 Target
42 Target
20 Target
Z0
Ω
RP
42 Target
25 Target
42 Target
20 Target
Z0
Ω
Differential
NA
NA
NA
NA
ZDIFF
Ω
Note: Nominal supply voltages. See Table 1, Tj = 105°C.
21.6
Configuration Pin Multiplexing
The MPC8347EA power-on configuration options can be set through external pull-up or pull-down
resistors of 4.7 kΩ on certain output pins (see the customer-visible configuration pins). These pins are used
as output only pins in normal operation.
However, while HRESET is asserted, these pins are treated as inputs, and the value on these pins is latched
when PORESET deasserts. Then the input receiver is disabled and the I/O circuit takes on its normal
function. Careful board layout with stubless connections to these pull-up/pull-down resistors coupled with
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
101
System Design Information
the large value of the pull-up/pull-down resistor should minimize the disruption of signal quality or speed
for the output pins.
21.7
Pull-Up Resistor Requirements
The MPC8347EA requires high resistance pull-up resistors (10 kΩ is recommended) on open-drain pins,
including I2C pins, the Ethernet Management MDIO pin, and EPIC interrupt pins.
Correct operation of the JTAG interface requires configuration of a group of system control pins as
demonstrated in Figure 43. Take care to ensure that these pins are maintained at a valid deasserted state
under normal operating conditions because most have asynchronous behavior, and spurious assertion
yields unpredictable results.
Refer to the PCI 2.3 specification for all pull-ups required for PCI.
21.8
JTAG Configuration Signals
Boundary scan testing is enabled through the JTAG interface signals. The TRST signal is optional in the
IEEE Std. 1149.1 specification, but it is provided on all processors that implement the PowerPC
architecture. The MPC8347EA requires TRST to be asserted during reset conditions to ensure that the
JTAG boundary logic does not interfere with normal chip operation. While the TAP controller may be
forced to the reset state using only the TCK and TMS signals, systems typically assert TRST during
power-on reset. Because the JTAG interface is also used for accessing the common on-chip processor
(COP) function, simply tying TRST to PORESET is not practical.
The PowerPC COP function allows a remote computer system (typically, a PC with dedicated hardware
and debugging software) to access and control the internal operations of the processor. The COP interface
connects through the JTAG port of the processor, with some additional status monitoring signals. The COP
port requires the ability to assert TRST independently without causing PORESET. If the target system has
independent reset sources, such as voltage monitors, watchdog timers, power supply failures, or
push-button switches, the COP reset signals must be merged into these signals with logic.
The arrangement shown in Figure 43 allows the COP to assert HRESET or TRST independently, while
ensuring that the target can drive HRESET as well. If the JTAG interface and COP header are not used,
TRST should be tied to PORESET so that it is asserted when the system reset signal (PORESET) is
asserted.
The COP header shown in Figure 43 adds many benefits—breakpoints, watchpoints, register and memory
examination/modification, and other standard debugger features. It requires no more effort than adding an
unpopulated footprint for a header when needed. The COP interface has a standard header for connection
to the target system, based on the 0.025" square-post, 0.100" centered header assembly (often called a Berg
header). There is no standardized way to number the header, shown in Figure 43, so emulator vendors use
different pin numbering schemes. Some headers are numbered top-to-bottom then left-to-right, others use
left-to-right then top-to-bottom, and still others number the pins counter clockwise from pin 1 (as with an
IC). Regardless of the numbering scheme, the signal placement recommended in Figure 43 is common to
all known emulators.
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
102
Freescale Semiconductor
System Design Information
PORESET
PORESET
From Target
Board Sources
(if any)
SRESET
SRESET
HRESET
HRESET
13
11
10 kΩ
HRESET
OVDD
SRESET
OVDD
10 kΩ
OVDD
10 kΩ
OVDD
1
2
3
4
5
6
7
8
9
10
11
12
4
61
5
15
10 kΩ
TRST
VDD_SENSE
TRST
2 kΩ
OVDD
NC
CHKSTP_OUT
CHKSTP_OUT
10 kΩ
OVDD
14
KEY
13 No
pin
16
COP Connector
Physical Pin Out
OVDD
CHKSTP_IN
COP Header
15
10 kΩ
2
CHKSTP_IN
8
TMS
9
1
3
TMS
TDO
TDI
TDO
TDI
TCK
7
TCK
2
NC
10
NC
12
NC
16
Notes:
1. Some systems require power to be fed from the application board into the debugger repeater card
via the COP header. The resistor value for VDD_SENSE should be around 20Ω .
2. Key location; pin 14 is not physically present on the COP header.
Figure 43. JTAG Interface Connection
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
103
Document Revision History
22 Document Revision History
Table 66 provides a revision history of this document.
Table 69. Document Revision History
Revision
Date
Substantive Change(s)
3
11/2006
Updated note in introduction.
In Table 5, “MPC8347EA Typical I/O Power Dissipation,” added GVDD 1.8-V values for DDR2;
added table footnote to designate rates that apply only to the TBGA package.
In the features list in Section 1, “Overview,” corrected DDR data rate to show:
• 266 MHz for PBGA parts for all silicon revisions
400 MHz for DDR2 for TBGA parts for silicon Rev. 2 and 3In Section 23, “Ordering Information,”
replicated note from document introduction.
2
8/2006
Changed all references to revision 2.0 silicon to revision 3.0 silicon.
Changed VIH minimum value in Table 39, “JTAG Interface DC Electrical Characteristics,” to
OVDD – 0.3.
In Table 63, “Suggested PLL Configurations,” deleted reference-number rows 902 and 703.
In Table 40, “PCI DC Electrical Characteristics,” changed high-level input voltage values to min =
2 and max = OVDD + 0.3; changed low-level input voltage values to min = (–0.3) and max = 0.8.
In Table 44, “PCI DC Electrical Characteristics,” changed high-level input voltage values to min =
2 and max = OVDD + 0.3; changed low-level input voltage values to min = (–0.3) and max = 0.8.
Updated DDR2 I/O power values in Table 5, “MPC8347EA Typical I/O Power Dissipation.”
1
4/2006
Removed Table 20, “Timing Parameters for DDR2-400.”
Changed ADDR/CMD to ADDR/CMD/MODT in Table 9, “DDR and DDR2 SDRAM Output AC
Timing Specifications,” rows 2 and 3, and in Figure 2, “DDR SDRAM Output Timing Diagram.
Changed Min and Max values for VIH and VIL in Table 40,“PCI DC Electrical Characteristics.”
In Table 51, “MPC8347EA (TBGA) Pinout Listing,” and Table 52, “MPC8347EA (PBGA) Pinout
Listing,” modified rows for MDICO and MDIC1 signals and added note “It is recommended that
MDICO be tied to GRD using an 18 Ω resistor and MCIC1 be tied to DDR power using an 18 Ω
resistor.”
In Table 51, “MPC8347EA (TBGA) Pinout Listing,” and Table 52, “MPC8347EA (PBGA) Pinout
Listing,” in row AVDD3 changed power supply from “AVDD3” to “—.”
0
3/2006
Initial Release
23 Ordering Information
This section presents ordering information for the device discussed in this document, and it shows an
example of how the parts are marked. The information in this document is accurate for revision 3.x silicon
and later (in other words, for devices with part numbers ending in A or B, such as the MPC8347EA or
MPC8347EB). For information on revision 1.1 silicon and earlier versions (MPC8347E/MPC8347), see
the PowerQUICC™ II Pro Integrated Host Processor Hardware Specifications
23.1
Part Numbers Fully Addressed by this Document
Table 67 shows an analysis of the Freescale part numbering nomenclature for the MPC8347EA. The
individual part numbers correspond to a maximum processor core frequency. For available frequencies,
contact your local Freescale sales office. Also the part numbering scheme includes an application modifier
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
104
Freescale Semiconductor
Ordering Information
to specify special application conditions. Each part number also contains a revision code that refers to the
die mask revision number.
Table 70. Part Numbering Nomenclature
MPC nnnn
e
t
pp
aa
a
r
Product
Part
Code Identifier
Encryption
Acceleration
Temperature1
Range
Package 2
Processor
Frequency 3
Platform
Frequency
Revision
Level
Blank = Not
included
E = included
Blank = 0 to 105°C
C= –40 to 105°C
ZU =TBGA
VV = PB free TBGA
ZQ = PBGA
VR = PB Free PBGA
e300 core
speed
AD =266
AG = 400
AJ = 533
AL = 667
D = 266
F = 333
B = 3.1
MPC
8347
Notes:
1. For temperature range = C, processor frequency is limited to 400 with a platform frequency of 266.
2. See Section 17, “Package and Pin Listings” for more information on available package types.
3. Processor core frequencies supported by parts addressed by this specification only. Not all parts described in this
specification support all core frequencies. Additionally, parts addressed by Part Number Specifications may support other
maximum core frequencies.
Table 68 shows the SVR settings by device and package type.
Table 71. SVR Settings
Device
Package
SVR (Rev. 3.0)
MPC8347EA
TBGA
8052_0030
MPC8347A
TBGA
8053_0030
MPC8347EA
PBGA
8054_0030
MPC8347A
PBGA
8055_0030
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
105
Ordering Information
23.2
Part Marking
Parts are marked as in the example shown in Figure 44.
MPCnnnnetppaaar
core/platform MHZ
ATWLYYWW
CCCCC
*MMMMM
Notes:
YWWLAZ
TBGA/PBGA
ATWLYYWW is the traceability code.
CCCCC is the country code.
MMMMM is the mask number.
YWWLAZ is the assembly traceability code.
Figure 44. Freescale Part Marking for TBGA or PBGA Devices
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
106
Freescale Semiconductor
Ordering Information
THIS PAGE INTENTIONALLY LEFT BLANK
MPC8347EA PowerQUICC II Pro Integrated Host Processor Hardware Specifications, Rev. 3
Freescale Semiconductor
107
How to Reach Us:
Home Page:
www.freescale.com
email:
[email protected]
USA/Europe or Locations Not Listed:
Freescale Semiconductor
Technical Information Center, CH370
1300 N. Alma School Road
Chandler, Arizona 85224
1-800-521-6274
480-768-2130
[email protected]
Information in this document is provided solely to enable system and software
implementers to use Freescale Semiconductor products. There are no express or
implied copyright licenses granted hereunder to design or fabricate any integrated
circuits or integrated circuits based on the information in this document.
Europe, Middle East, and Africa:
Freescale Halbleiter Deutschland GmbH
Technical Information Center
Schatzbogen 7
81829 Muenchen, Germany
+44 1296 380 456 (English)
+46 8 52200080 (English)
+49 89 92103 559 (German)
+33 1 69 35 48 48 (French)
[email protected]
Freescale Semiconductor reserves the right to make changes without further notice to
Japan:
Freescale Semiconductor Japan Ltd.
Headquarters
ARCO Tower 15F
1-8-1, Shimo-Meguro, Meguro-ku
Tokyo 153-0064, Japan
0120 191014
+81 3 5437 9125
[email protected]
parameters, including “Typicals” must be validated for each customer application by
Asia/Pacific:
Freescale Semiconductor Hong Kong Ltd.
Technical Information Center
2 Dai King Street
Tai Po Industrial Estate,
Tai Po, N.T., Hong Kong
+800 2666 8080
[email protected]
unauthorized application, Buyer shall indemnify and hold Freescale Semiconductor
For Literature Requests Only:
Freescale Semiconductor
Literature Distribution Center
P.O. Box 5405
Denver, Colorado 80217
1-800-441-2447
303-675-2140
Fax: 303-675-2150
LDCForFreescaleSemiconductor
@hibbertgroup.com
Freescale™ and the Freescale logo are trademarks of Freescale Semiconductor, Inc.
The Power Architecture and Power.org word marks and the Power and Power.org logos
and related marks are trademarks and service marks licensed by Power.org. The
described product contains a PowerPC processor core. The PowerPC name is a
trademark of IBM Corp. and used under license. All other product or service names are
the property of their respective owners.
Document Number: MPC8347EAEC
Rev. 3
11/2006
any products herein. Freescale Semiconductor makes no warranty, representation or
guarantee regarding the suitability of its products for any particular purpose, nor does
Freescale Semiconductor assume any liability arising out of the application or use of
any product or circuit, and specifically disclaims any and all liability, including without
limitation consequential or incidental damages. “Typical” parameters which may be
provided in Freescale Semiconductor data sheets and/or specifications can and do
vary in different applications and actual performance may vary over time. All operating
customer’s technical experts. Freescale Semiconductor does not convey any license
under its patent rights nor the rights of others. Freescale Semiconductor products are
not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Freescale Semiconductor product
could create a situation where personal injury or death may occur. Should Buyer
purchase or use Freescale Semiconductor products for any such unintended or
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all
claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Freescale
Semiconductor was negligent regarding the design or manufacture of the part.
© Freescale Semiconductor, Inc., 2005, 2006.