SY88932L 3.3V, 4.25Gbps SONET/SDH Laser Driver with Output Disable General Description Features The SY88932L is the smallest available laser driver with a programmable modulation current up to 60mA for FabryPerot (FP) or distribution feedback (DFB) lasers. The device is suitable for SOENT/SDH applications with data rates up to 4.25Gbps. The SY88932L accepts either CML level or AC-coupled PECL inputs, and incorporates an active low TTL /EN function which shuts off the modulation current when HIGH. Datasheets and support documentation can be found on Micrel’s web site at www.micrel.com. • • • • • • • • • • Up to 4.25Gbps operation Modulation current to 60mA Rise/fall times 65ps typical Input 50Ω internally terminated to VCC TTL /EN with internal 75kΩ pull-down Designed for use with MIC3000 optical transceiver management IC Voltage programmable laser modulation current Single 3.3V power supply Operating temperature range of –40°C to +85°C Available in tiny 16-pin MLF® package Applications • • • • • • • Fiber optical module Transponder XAUI CWDM SONET/ SDH transmission system Add-drop MUX Metro area network 4.25Gbps optical transmitter ___________________________________________________________________________________________________________ Block Diagram MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com February 2008 M9999-022008-F [email protected] or (408) 955-1690 Micrel, Inc. SY88932L Ordering Information Package Type Operating Range Package Marking Lead Finish MLF-16 Industrial 932L Sn-Pb SY88932LMITR MLF-16 Industrial 932L Sn-Pb SY88932LMG MLF-16 Industrial 932L with Pb-Free bar-line indicator Pb-Free NiPdAu SY88932LMGTR(1) MLF-16 Industrial 932L with Pb-Free bar-line indicator Pb-Free NiPdAu Part Number SY88932LMI (1) Note: 1. Tape and Reel. Pin Configuration 16-Pin MLF® (MLF-16) February 2008 2 M9999-022008-F [email protected] or (408) 955-1690 Micrel, Inc. SY88932L Pin Description Pin Number Pin Name Pin Function 2, 3 DIN, /DIN NRZ differential data (inputs), CML terminated interface with 50Ω to VCC. 1, 4, 7, 8, 13 GND Ground. Positive power supply. 5, 6 VCC 9, 10, 11, 12 OUT, /OUT 14 VREF 15 VCNTRL 16 /EN Open collector (outputs) from the modulation driver. Voltage reference, nominally 1.25V with respect to ground. Voltage control of IMOD. 5kΩ input impedance. See “Typical Operating Characteristics.” Enable: TTL-compatible active low input with 75kΩ pull-down resistor. Truth Table(1,2) D /D /EN OUT(3) /OUT L H L H L H L L L H X X H H L Notes: 1. Truth table parameters are given for voltage rather than optical outputs. Hence, a voltage HIGH and OUT means no modulation current is flowing through OUT, and a voltage LOW on OUT means modulation current is flowing through OUT. A voltage LOW implies an optical HIGH, and vice versa. 2. L = LOW, H = HIGH, X = don’t care. 3. IOUT ≤ IMOD_OFF when /EN is HIGH. February 2008 3 M9999-022008-F [email protected] or (408) 955-1690 Micrel, Inc. SY88932L Absolute Maximum Ratings(1) Operating Ratings(2) Supply Voltage (VCC).................................... –0.5V to +4.0V CML Input Voltage (VIN) ..................VCC –1.0V to VCC +0.5V TTL Control Input Voltage (VIN)............................. 0V to VCC Lead Temperature (soldering, 20sec.)....................... 265°C Storage Temperature (Ts) .........................–65°C to +150°C Supply Voltage (VCC).................................... +3.0V to +3.6V Ambient Temperature (TA) .......................... –40°C to +85°C Junction Temperature (TJ) ........................ –40°C to +120°C Junction Thermal Resistance(3) MLF® (θJA) Still-Air .......................................................61°C/W (ψJB) Still-Air.......................................................38°C/W DC Electrical Characteristics VCC = 3.0V to 3.6V; GND = 0V; TA = –40°C to +85°C, Typical values at VCC = 3.3V, TA = 25°C. Symbol Parameter Condition ICC Power Supply Current Note 4 IMOD Modulation Current Range Min Typ Max Units 57 80 mA 10 60 mA 200 µA VCC–0.8 VCC+0.4 V 1600 mVPP IMOD_OFF Modulation Off Current VIR CML Input Voltage Range /EN = VIHEN VID CML Input Differential Voltage (DIN, /DIN) VIHEN TTL Input HIGH Voltage (/EN) VILEN TTL Input LOW Voltage (/EN) VOUT Voltage (OUT, /OUT) Note 6 VCC–1.5 VREF Reference Voltage Note 7 1.2 Note 5 400 800 2.0 V 1.25 0.8 V VCC V 1.3 V Notes: 1. Permanent device damage may occur is Absolute Maximum Ratings are exceeded. This is a stress rating only and functional operation is not implied at conditions other than those detailed in the operational sections of this datasheet. Exposed to Absolute Maximum Ratings conditions for extended periods may affect device reliability. 2. The device is not guaranteed to function outside its operating rating. 3. Thermal resistance numbers are 4-layer PCB. Thermal performance assumes exposed pad is soldered (or equivalent) to the same potential as the ground pins on the PCB. 4. Excluding IMOD. IMOD set to 60mA with 25Ω load to VCC on OUT, /OUT. Inputs floating. 5. VID is the voltage required to guarantee a stable logic level. For logic “1”, DIN must be VID/2 above /DIN. For stable logic “0”, DIN must be VID/2 below /DIN. 6. OUT and /OUT are current outputs. This specification defines the voltage range that the user must guarantee these pins remain within for proper operation. 7. VREF intended to source/sink ≤ |5mA|. February 2008 4 M9999-022008-F [email protected] or (408) 955-1690 Micrel, Inc. SY88932L AC Electrical Characteristics(8) VCC = 3.0V to 3.6V; GND = 0V; TA = –40°C to +85°C, Typical values at VCC = 3.3V, TA = 25°C. Symbol Parameter Condition tr, tf Output Rise/Fall Times (20% to 80%) DJ Deterministic Jitter Min Typ Max Units Note 9 65 100 ps Note 9, 10 20 psPP Notes: 8. AC characteristics are guaranteed by design and characterization. 9. IMOD = 60mA. 10. Deterministic jitter measured using K28.5 pattern of 2.486Gbps, VID = 1600mVPP. Typical Operating Characteristics February 2008 5 M9999-022008-F [email protected] or (408) 955-1690 Micrel, Inc. SY88932L Package Information 16-Pin MLF® (MLF-16) February 2008 6 M9999-022008-F [email protected] or (408) 955-1690 Micrel, Inc. SY88932L PCB Thermal Consideration for 16-Pin MLF® Package Package Notes: 1. Package meets Level 2 qualifications. 2. All parts are dry-packaged before shipment. 3. Exposed pads must be soldered to a ground for proper thermal management. MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2008 Micrel, Incorporated. February 2008 7 M9999-022008-F [email protected] or (408) 955-1690