MOTOROLA M68ICS08KX

In-circuit Simulator Board
User’s Manual
N O N - D I S C L O S U R E
M68ICS08KX
A G R E E M E N T
R E Q U I R E D
M68ICS08KXUM/D
User’s Manual
Important Notice to Users
While every effort has been made to ensure the accuracy of all information in this document, Motorola
assumes no liability to any party for any loss or damage caused by errors or omissions or by statements of
any kind in this document, its updates, supplements, or special editions, whether such errors are omissions
or statements resulting from negligence, accident, or any other cause. Motorola further assumes no liability
arising out of the application or use of any information, product, or system described herein: nor any
liability for incidental or consequential damages arising from the use of this document. Motorola disclaims
all warranties regarding the information contained herein, whether expressed, implied, or statutory,
including implied warranties of merchantability or fitness for a particular purpose. Motorola makes no
representation that the interconnection of products in the manner described herein will not infringe on
existing or future patent rights, nor do the descriptions contained herein imply the granting or license to
make, use or sell equipment constructed in accordance with this description.
Trademarks
This document includes these trademarks:
Motorola and the Motorola logo are registered trademarks
of Motorola, Inc.
Windows and Windows 95 are registered trademarks of Microsoft Corporation in the U.S. and other
countries.
Intel is a registered trademark of Intel Corporation.
Motorola, Inc., is an Equal Opportunity / Affirmative Action Employer.
For an electronic copy of this book, visit Motorola’s web site at http://mcu.motsps.com/documentation
© Motorola, Inc., 2000; All Rights Reserved
User’s Manual
2
M68ICS08KX In-circuit Simulator Board
MOTOROLA
Table of Contents
User’s Manual — M68ICS08KX In-Circuit Simulator
Table of Contents
Section 1. General Information
1.1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.2
1.2.1
1.2.2
KXICS Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
KXICS Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
ICS Interface Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.3
Hardware and Software Requirements . . . . . . . . . . . . . . . . . . . . . . . . 13
1.4
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.5
About This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.6
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Section 2. Preparation and Installation
2.1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.2
Hardware Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.2.1
KXICS Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.2.2
Configuring the KXICS Jumper Headers . . . . . . . . . . . . . . . . . . . 16
2.2.3
Installing an MCU on the KXICS . . . . . . . . . . . . . . . . . . . . . . . . . 17
2.2.4
Connecting the KXICS to the host PC. . . . . . . . . . . . . . . . . . . . . . 18
2.2.5
Applying power to the KXICS. . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
2.2.6
Target Cable Interface Connection Options. . . . . . . . . . . . . . . . . . 19
2.3
Target Cable Interface Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
2.3.1
Host Computer - KXICS Interconnection J6 . . . . . . . . . . . . . . . . . 23
2.3.2
Power Connector J2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
2.4
Connecting the KXICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
2.5
Connecting the KXICS to the Target System . . . . . . . . . . . . . . . . . . . 24
2.6
Installing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Table of Contents
3
Table of Contents
Section 3. Support Information
3.1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.2
MCU Subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
3.3
Level Translation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.4
KXICS Theory of Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.4.1
Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.4.2
Serial Communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.4.3
Clock Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
3.4.4
Start-Up in Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3.5
3.5.1
3.5.2
3.5.3
3.5.4
3.5.5
KXICS Connector Signal Definitions. . . . . . . . . . . . . . . . . . . . . . . . . 32
Target Flex Cable Interface Connector J1 . . . . . . . . . . . . . . . . . . . 32
Target Ribbon Interface Connector J5 . . . . . . . . . . . . . . . . . . . . . . 33
Target MONO8 Interface Connector J3. . . . . . . . . . . . . . . . . . . . . 34
Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
RS-232C Communication Connector, J6. . . . . . . . . . . . . . . . . . . . 36
3.6
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.7
KXICS Board Layout and Schematics Diagrams. . . . . . . . . . . . . . . . 40
Section 4. Using the MON08 Interface
4.1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
4.2
Target System Header Placement and Layout . . . . . . . . . . . . . . . . . . 41
4.3
Connecting to the In-Circuit Simulator . . . . . . . . . . . . . . . . . . . . . . . 42
Appendix A. S-Record Information
A.1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
A.2
S-Record Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
A.3
S-Record Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
A.4
S Record Creation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
A.5
S-Record Example . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
A.5.1
S0 Header Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
User’s Manual
4
M68ICS08KX In-Circuit Simulator
Table of Contents
MOTOROLA
Table of Contents
A.5.2
A.5.3
A.5.4
First S1 Record. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
S9 Termination Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
ASCII Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Appendix B. Quick Start Hardware Configuration Guide
B.1
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
B.1.1
KXICS Configurable Jumper Headers. . . . . . . . . . . . . . . . . . . . . . 50
B.1.2
Target Interface Cable Connections. . . . . . . . . . . . . . . . . . . . . . . . 51
B.1.3
Host Computer — KXICS Interconnection (J6) . . . . . . . . . . . . . . 51
B.2
Installing the Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
B.3
Installing the Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
B.4
Connecting to a Target System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Glossary
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Table of Contents
5
Table of Contents
User’s Manual
6
M68ICS08KX In-Circuit Simulator
Table of Contents
MOTOROLA
List of Figures
User’s Manual — M68ICS08KX In-Circuit Simulator
List of Figures
Figure
1-1
2-1
2-2
2-3
3-1
Title
Motorola M68ICS08KX (KXICS) Board . . . . . . . . . . . . . . . . . . . . . 12
KXICS with SOIC-to-DIP Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Host Computer to KXICS Interconnection . . . . . . . . . . . . . . . . . . . . 28
J2 Power Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
KXICS Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
M68ICS08KX In-Circuit Simulator
MOTOROLA
Page
User’s Manual
List of Figures
7
List of Figures
User’s Manual
8
M68ICS08KX In-Circuit Simulator
List of Figures
MOTOROLA
List of Tables
User’s Manual — M68ICS08KX In-Circuit Simulator
List of Tables
Table
Title
Page
Table 1-1. KXICS Product Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Table 1-2. Hardware Connector Components . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 1-3. Software Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 1-4. KXICS Board Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Table 2-1 KXICS Jumper Header Description . . . . . . . . . . . . . . . . . . . . . . . . 21
Table 2-2. Cable/Connector Options for MCUs . . . . . . . . . . . . . . . . . . . . . . . 23
Table 2-3 J1 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Table 2-4 J5 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Table 2-5 J3 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Table 3-1 J1 Target Flex Connector Pin Assignments . . . . . . . . . . . . . . . . . . 36
Table 3-2 J5 Target Connector Pin Assignments . . . . . . . . . . . . . . . . . . . . . . 38
Table 3-3 J3 MONO8 Target Connector Pin Assignments . . . . . . . . . . . . . . 39
Table 3-4 Power Connector J2 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . 39
Table 3-5 RS-232C Communication Connector J6 Pin Assignments . . . . . . 40
Table 3-6. KXICS Parts List (Rev F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Table 4-1. MON08 Target System Connector J3 . . . . . . . . . . . . . . . . . . . . . . 45
Table 4-2 KXICS Jumper Header Description . . . . . . . . . . . . . . . . . . . . . . . . 54
Table 4-3 Cable/Connector Options for MCUs . . . . . . . . . . . . . . . . . . . . . . . 55
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
List of Tables
9
List of Tables
User’s Manual
10
M68ICS08KX In-Circuit Simulator
List of Tables
MOTOROLA
User’s Manual — M68ICS08KX In-Circuit Simulator
Section 1. General Information
1.1 Introduction
This section provides general information about the Motorola M68ICS08KX
in-circuit simulator (KXICS).
The KXICS board (Figure 1-1) is a stand-alone development and debugging
tool. It contains the hardware and software needed to develop and simulate
source code and to program Motorola’s MC68HC908KX8 microcontroller
(MCU).
The KXICS and it’s software form a complete editor, assembler, programmer,
simulator, and limited real-time input/output emulator for the MCU. When
connection is made between a host PC (personal computer) and target hardware
(your prototype product), actual inputs and outputs of the target system may be
used during code simulation.
The KXICS can interface with any IBM Windows 95-based computer (or
later version) through connection of a single RS-232 serial port using a DE-9
serial cable.
Connection to the target system is accomplished by a ribbon cable, a Motorola
M68CLB05A flex cable, or a MONO8 cable. The ribbon cable or flex cable is
used when an MCU is resident on the KXICS for emulation or simulation, and
the MONO8 cable is used to debug or program a target system’s MCU, directly,
when the MCU resides on the target hardware.
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
General Information
11
General Information
Figure 1-1 Motorola M68ICS08KX (KXICS) Board
The KXICS is a low-cost development system that supports editing,
assembling, in-circuit simulation, in-circuit emulation, and FLASH memory
programming. Its features include:
•
Editing with WinIDE
•
Assembling with CASM08W
•
Programming FLASH memory with PROG08SZ
•
Simulating in-circuit and stand-alone MC68HC908KX8 MCU with
ICS08KXW software, providing:
•
–
Simulation of all instructions, memory, and peripherals
–
Simulation of pin inputs from the target system
–
Installation of conditional breakpoints, script files, and logfiles
Debugging and emulation (limited real-time) with ICD08SZ, including:
User’s Manual
12
M68ICS08KX In-Circuit Simulator
General Information
MOTOROLA
General Information
Introduction
–
Loading code into RAM
–
Executing real-time in RAM or FLASH
–
Placing one hardware breakpoint in FLASH
–
Placing multiple breakpoints in RAM
•
On-line help documentation for all software
•
Software integrated into the WinIDE environment, allowing function
key access to all applications
•
MON08 emulation connection to the target system allowing:
•
–
In-circuit emulation
–
In-circuit simulation
–
In-circuit programming
Four modes of operation:
–
Standalone — using the KXICS as a standalone system without a
target board
–
Simulation — using the KXICS as an in-circuit simulator/emulator
with a target cable
–
Evaluation - using the KXICS for real-time evaluation of the MCU
and to debug user developed hardware and software
–
Programming — using the KXICS as a programmer
•
With the ICD08SZ debugging software, code can be run directly out of
the MCU’s internal FLASH at real-time speeds.
•
With the WinIDE, CASM08Z, editor, simulator, and assembler software,
the function is as a limited real-time emulator.
•
With the PROG08SZ software, the function is to program MCU FLASH
memory.
•
With the ICS08KXZ simulation software, the MCU provides the
required input/output information that lets the host computer simulate
code, performing all functions except for maintaining port values. (The
internal FLASH memory on the device is downloaded with a program
that generates the appropriate port values.) The ICS08KXZ software on
the host computer lets the host computer become a simulator.
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
General Information
13
General Information
•
With using the ICD08SZ debugging software, code can be run directly
out of the MCU’s internal FLASH at real-time speeds.
•
Timing is accomplished with a 9.8304 MHz crystal
User’s Manual
14
M68ICS08KX In-Circuit Simulator
General Information
MOTOROLA
General Information
KXICS Components
1.2 KXICS Components
The complete KXICS system includes hardware, software, and documentation.
lists the KXICS product components.
Table 1-1. KXICS Product Components
Part Number
Description
ICS08KX
KXICS software development package
ICS08KXZ
KXICS software simulator
ICD08SZ
KXICS software debugger/emulation
MC68HC908KX8CP
MCU (16-pin DIP package)
MC68HC908KX8CDW
MCU (16-pin SOIC Package)
PA16SO-08H-3
SOIC-to-DIP Socket Adapter
M68CLB05A
Flex target cable
KRISTA 22-122
Serial cable
FRIWO 11.8999-P5
Power supply
M68ICS08SOM/D
In-circuit simulator software operator’s manual
M68ICS08KXHOM/D
In-circuit simulator hardware operator’s manual
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
General Information
15
General Information
1.2.1 KXICS Hardware
lists the KXICS hardware components.
Table 1-2. Hardware Connector Components
Components
Description
Test socket for the Motorola MC68HC908KX8 MCU: 16-pin
DIP (dual in-line package)
XU1
J1
Two 2-row × 20-pin, 0.1-inch spacing connectors to connect
the KXICS to a target using the M68CLB05A flex cable
J2
+5 Vdc input voltage (VDD)
J3
One 2-row × 8-pin, 0.1-inch spacing connector to connect to a
remote target via the MON08 debug circuit.
J4
J4 is the clock output that may be used for synchronizing a
target or test equipment to the KXICS clock.
J5
One 2-row × 8-pin, 0.3-inch spacing dual in-line package (DIP)
socket to allow the KXICS to be connected to the target using
a ribbon cable
J6
RS-232 to interface KXICS to host computer serial connector
(DEKL-9SAT-F)
1.2.2 ICS Interface Software
Windows-optimized software components are referred to, collectively, as the
KXICS software (part number ICS08KX). It is a product of P&E
Microcomputer Systems, Inc. and is included in the KXICS kit ().
Table 1-3. Software Components
Components
Description
WINIDE.EXE
Integrated development environment (IDE) software
interface for editing and performing software or
in-circuit simulation
CASM08Z.EXE
CASM08Z command-line cross-assembler
ICS08SZ.EXE
In-circuit/stand-alone simulator software for the
MC68HC908KX8 MCU
PROG08SZ.EXE
FLASH memory programming software
ICD08SZ.EXE
In-circuit debugging software for limited, real-time
emulation
User’s Manual
16
M68ICS08KX In-Circuit Simulator
General Information
MOTOROLA
General Information
Hardware and Software Requirements
1.3 Hardware and Software Requirements
The KXICS software requires this minimum hardware and software
configuration:
•
Windows 95 or later version operating system
•
Approximately 2 Mbytes of available random-access memory (RAM)
and 5 Mbytes of free disk space
•
A serial port for communications between the KXICS and the host
computer
1.4 Specifications
Table 1-4 summarizes the KXICS hardware specifications.
Table 1-4. KXICS Board Specifications
Characteristic
Specification
Temperature:
Operating
Storage
0° to 40°C
–40° to +85°C
Relative humidity
0 to 95%, non-condensing
Power requirement
+5 Vdc, from included ac/dc adapter
1.5 About This Manual
The procedural instructions in this manual assume that the user is familiar with
the Windows interface and selection procedures.
1.6 Customer Support
To obtain information about technical support or ordering parts, call the
Motorola help desk at 800-521-6274.
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
General Information
17
General Information
User’s Manual
18
M68ICS08KX In-Circuit Simulator
General Information
MOTOROLA
User’s Manual — M68ICS08KX In-Circuit Simulator
Section 2. Preparation and Installation
2.1 Introduction
This section provides information and instruction for configuring, installing,
and readying the M68ICS08KX (KXICS) for use.
2.2 Hardware Preparation
ESD CAUTION:
Ordinary amounts of static electricity from clothing or the work environment
can damage or degrade electronic devices and equipment. For example, the
electronic components installed on the printed circuit board are extremely
sensitive to electrostatic discharge (ESD). Wear a grounding wrist strap
whenever handling any printed circuit board. This strap provides a conductive
path for safely discharging static electricity to ground.
2.2.1 KXICS Limitations
These sub-paragraphs describe system limitations of the KXICS.
2.2.1.1 Bus Frequency
The KXICS communicates using the MON08 features which forces the
communication rate to fbus/256, and the bus frequencies are limited by standard
baud rates allowed by the host software.
2.2.1.2 Port A0
Port A0 is used for communications, so it is unavailable for emulation.
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Preparation and Installation
19
Preparation and Installation
2.2.1.3 Low Voltage Interrupt (LVI)
The LVI is disabled by default in monitor mode. It is enabled by a dummy write
to LVISR.
2.2.1.4 Internal Clock Generator (ICG)
The ICG is bypassed in monitor mode, so it is not available for use.
2.2.2 Configuring the KXICS Jumper Headers
The KXICS supports four configuration options: standalone, simulation,
evaluation, and programming.
•
Standalone — ICS08KXZ.exe running on the host computer (the KXICS
is not connected.) Emulation of the MCU CPU, registers, and I/O ports
is done within the host computer environment.
•
Simulation — Host computer is connected to the KXICS via the RS-232
cable and ICS08KXZ.exe runs on the host computer, providing access to
the M68HC(9)08KX MCU CPU internal registers and I/O ports.
•
Evaluation — Host computer is connected to the KXICS, and the KXICS
is connected to the target system via the flex cable, providing limited
real-time evaluation of the MCU and debugging user developed
hardware and software.
•
Programming — Host computer is connected to the KXICS, and the
KXICS is connected to the target system via the MON08 cable with
PROG08SZ.exe used to program the MCU FLASH module. In the
programming mode there is limited evaluation (port A0 on the KX8 and
port B0 and port B1 on the KX8 are used for communications, so they
are unavailable for emulation).
Four jumper headers (Table 2-1) on the KXICS are used to configure the
hardware options.
CAUTION:
The KXICS can be set to operate at a variety of voltages. When configuring the
KXICS jumper headers, care must be exercised to ensure that the voltages
selected for the board match those of the target device. Failure to do so can
result in damage to either or both of the pieces of equipment.
User’s Manual
20
M68ICS08KX In-Circuit Simulator
Preparation and Installation
MOTOROLA
Preparation and Installation
Hardware Preparation
Table 2-1 KXICS Jumper Header Description
Jumper
Header
Type
1
2
W1
Low Voltage
Select
12
11
W2
MCU Voltage
Select
3
1
W3
Target Clock
Select
W4
PTB6 Select
Description
(Factory
Default Shown
3
1
1
3
Used to set power for the MCU to match various target voltages.(No
default)
Jumper on position 1 & 2:
3.3 V
Jumper on position 3 & 4:
3.0 V
Jumper on position 5 & 6:
2.7 V
Jumper on position 7 & 8
2.2 V
Jumper on position 9 & 10
2.0 V
Jumper on position 11 & 12:
ADJ
Selects voltage powering MCU and related circuitry.
Jumper on position 1&2: Regulator Lo V as set by W1, is supplied by
MCU. Labeled LO V.
Jumper on position 3&2: Power supply, 5V Switched, is supplied by
board to MCU. Labeled 5V.
Jumper on position 1&2: supplies KXICS,9.8304 MHz, clock, to MCU
and target via W4.
Jumper on position 3&2: disables Xtal clock output, which will affect the
power-up reset. Labeled 1.
Jumper on position 1&2: MCU’s internal clock is supplied to target
cable via PTB6.
Jumper on position 3&2: KXICS Xtal clock is supplied to MCU.
2.2.3 Installing an MCU on the KXICS
Either of two types of MCUs may be installed on the KXICS board, a DIP-type
or a SOIC-type.
2.2.3.1 DIP-type MCU
1. Place the pin tension arm of the KXICS DIP socket XU1 in the up
position.
2. Install the DIP type MCU into the DIP socket XU1. Be sure that the
pin 1 orientation of the silkscreened dot on the MCU aligns with the
pin 1 location on the DIP socket (upper left pin of the socket).
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Preparation and Installation
21
Preparation and Installation
3. Place the pin tension arm of the KXICS DIP socket XU1 in the down
position to secure the pins of the MCU to the socket.
NOTE:
The top (label side) of the MCU package must be visible when looking at the
component side of the board.
2.2.3.2 SOIC-type MCU
NOTE:
Installation of a SOIC type MCU requires the use of the SOIC-to-DIP adapter
identified in Table 1-1 of this manual.
1. Place the pin tension arm of the KXICS DIP socket XU1 (Figure 2-1)
in the up position.
2. Install the SOIC-to-DIP adapter into the DIP socket XU1 (Figure
2-1). Be sure that the pin 1 orientation of the adapter aligns with the
pin 1 location on the DIP socket (upper left pin of the DIP socket).
CAUTION:
The SOIC-to-DIP adapter may be confusing to install. It must be placed into the
DIP socket, XU1, with the hinged side of the SOIC shell aligned to the bottom
of the KXICS board. This positioning will place the SOIC-type MCU socket pin
1 in the upper left corner of the SOIC socket.
3. Place the pin tension arm of the KXICS DIP socket XU1 in the down
position to secure the pins of the adapter to the socket.
4. Open the hinged access door on the SOIC shell.
5. Install the SOIC-type MCU into the SOIC socket of the adapter. Be
sure that the pin 1 orientation of the silkscreened dot on the MCU
aligns with the pin 1 location on the SOIC socket (upper left pin of
the socket).
6. Close and secure the hinged access door on the SOIC shell.
User’s Manual
22
M68ICS08KX In-Circuit Simulator
Preparation and Installation
MOTOROLA
Preparation and Installation
Hardware Preparation
Figure 2-1 KXICS with SOIC-to-DIP Adapter
2.2.4 Connecting the KXICS to the host PC.
Locate the 9-pin connector labeled J6 on the board. Using the cable
provided, connect it to a serial COM port on the host PC.
2.2.5 Applying power to the KXICS.
CAUTION:
Although applying power is described here, do not apply power until all other
configuring, installing, and cable connections are completed. Equipment
damage can result.
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Preparation and Installation
23
Preparation and Installation
Connect the 5-volt power supply to the round connector on the board, J2.
Plug the power supply into an ac power outlet, using one of the
country-specific adapters provided. (The KXICS green power LED on
the board lights when switch SW1 is in the ON position.)
2.2.6 Target Cable Interface Connection Options
There are three ways to connect the KXICS simulator board to your target
system:
•
Flex cable — low-noise target interface connection (may be ordered
separately)
•
Ribbon cable — low-cost target interface connection
•
MON08 cable — target interface connection with MCU FLASH
programming and limited emulation
Below (Table 2-2) is a quick reference for defining the cable/connector
selection to use with the MC68HC908KX8. Select the option that meets your
requirements and connect accordingly.
Table 2-2. Cable/Connector Options for MCUs
MCU
Flex Cable
Ribbon
Cable
MON08
Cable
J1
J5
J3
MC68HC908KX8
User’s Manual
24
M68ICS08KX In-Circuit Simulator
Preparation and Installation
MOTOROLA
Preparation and Installation
Target Cable Interface Connectors
2.3 Target Cable Interface Connectors
NOTE:
Refer to Section 3, Support Information for more detail.
2.3.0.1 Target Flex Cable Interface Connector J1
The flex cable is a low-noise alternative connection that may be used to connect
to the target. Table 2-3 shows the pin assignments for flex cable connector J1.
Table 2-3 J1 Pin Assignments
J1
N/C
1
•
•
2
N/C
N/C
3
•
•
4
PTB7
N/C
5
•
•
6
PTB6
N/C
7
•
•
8
PTB5
N/C
9
•
•
10
PTB4
N/C
11
•
•
12
N/C
N/C
13
•
•
14
PTB3
TGT_PTA0
15
•
•
16
PTB2
TGT_PTA1
17
•
•
18
TGT_PTB1
TGT_PTA2
19
•
•
20
TGT_PTB0
TGT_PTA3
21
•
•
22
N/C
TGT_PTA4
23
•
•
24
N/C
N/C
25
•
•
26
IRQ*
N/C
27
•
•
28
N/C
Common
29
•
•
30
Common
Common
31
•
•
32
Common
Common
33
•
•
34
Common
Common
35
•
•
36
Common
Common
37
•
•
38
Common
Common
39
•
•
40
Common
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Preparation and Installation
25
Preparation and Installation
2.3.0.2 Target Ribbon Interface Connector J5
The KXICS includes a connector, J5 (Table 2-4), which allows a convenient,
less-expensive connection to the target, using a 16-pin ribbon cable.
Table 2-4 J5 Pin Assignments
J5
Common
1
•
•
16
N/CPTA1
PTA1
2
•
•
15
PTA4
PTA0
3
•
•
14
PTA3
IRQ*
4
•
•
13
PTA2
PTB0
5
•
•
12
PTB4
PTB1
6
•
•
11
PTB6
PTB2
7
•
•
10
OSC1/PTA3
PTB3
8
•
•
9
PTB7
User’s Manual
26
M68ICS08KX In-Circuit Simulator
Preparation and Installation
MOTOROLA
Preparation and Installation
Target Cable Interface Connectors
2.3.0.3 Target MONO8 Interface Connector J3
The MONO8 interface connector, J3 (Table 2-5), is used when the MCU is
mounted on the target. Refer to Section 4 Using the MONO8 for detailed
information.
Table 2-5 J3 Pin Assignments
J4
RST_OUT*
1
•
•
2
Common
RST_IN*
3
•
•
4
RST*
TGT_IRQ*
5
•
•
6
IRQ*
TGT_PTA0
7
•
•
8
PTA0
TGT_PTA1
9
•
•
10
PTA1
TGT_PTB0
11
•
•
12
PTB0
TGT_PTB1
13
•
•
14
PTB1
N/C
15
•
•
16
N/C
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Preparation and Installation
27
Preparation and Installation
2.3.1 Host Computer - KXICS Interconnection J6
The host computer to KXICS interface is via the single system connector J6,
which is a 9-pin, D-type connector (Amp part number AMP-9726-A) (Figure
2-2), mounted on the top side of the board.
Connection requires the cable assembly supplied with your KXICS kit, a
DB9-male-to-female, 6-ft. (3 m) long serial cable.
1
RXD 2
6
7 RTS
TXD 3
8
DTR 4
9
GND 5
Figure 2-2 Host Computer to KXICS Interconnection
2.3.2 Power Connector J2
Connect +5-Vdc power directly to the KXICS via connector J2 (Figure 2-3)
using the provided power supply.
+5 Vdc
GND
Figure 2-3. J2 Power Connector
User’s Manual
28
M68ICS08KX In-Circuit Simulator
Preparation and Installation
MOTOROLA
Preparation and Installation
Connecting the KXICS
2.4 Connecting the KXICS
The following steps provide instructions for connecting the KXICS to the host
PC and power connection.
ESD CAUTION:
Ordinary amounts of static electricity from clothing or the work environment
can damage or degrade electronic devices and equipment. For example, the
electronic components installed on the printed circuit board are extremely
sensitive to electrostatic discharge (ESD). Wear a grounding wrist strap
whenever handling any printed circuit board. This strap provides a conductive
path for safely discharging static electricity to ground.
a. Configure the jumpers W-1 through W-4 on the KXICS for your application.
b. Install an MCU into the appropriate socket, XU1, on the KXICS board.
NOTE:
Observe the pin 1 orientation with the silkscreened dot. The top (label side) of
the MCU package must be visible when looking at the component side of the
board.
c. Plug the serial cable into J6 on the KXICS.
d. Plug the serial cable into the COM port on the host PC.
NOTE:
Steps e. through g. should not be completed until all connections to the target
are completed (Paragraph 2.5).
e. Connect the power cable to J2 on the KXICS board.
f. Plug the power cable into an ac power outlet, using one of the country-specific
adapters.
g. The KXICS power LED lights green.
2.5 Connecting the KXICS to the Target System
Connect the KXICS to the target system using one of these methods:
•
Emulating using a flex cable for low-noise
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Preparation and Installation
29
Preparation and Installation
When emulating, connect the 40-pin M68CLB05A flex cable to the
connector labeled J1on the simulator board. Attach the other end of the
cable to the appropriate connector on the target system. Target head
adapters are available.
•
Emulating using a ribbon cable
When emulating, connect a 16-pin flat ribbon cable to connector J5 on
the simulator board. Attach the other end of the cable to the appropriate
connector on the target system.
•
NOTE:
Using a MON08 cable to debug the target system.
An MCU must be installed in the target system. No MCU should on the KXICS.
Connect the MON08 debug interface cable to the appropriate MON08
debug interface connector, J3, for communication with the target
system’s MCU. Attach the other end of the cable to the appropriate
connector on the target system.
NOTE:
For more detailed information on the MONO8, refer to Section 4 of this manual.
2.6 Installing the Software
For instructions for installing the ICS08 software, refer to P&E Microcomputer
Systems, Inc., M68ICS08 68HC08 In-Circuit Simulator Operator’s Manual,
Motorola document order number M68ICS08OM/D.
User’s Manual
30
M68ICS08KX In-Circuit Simulator
Preparation and Installation
MOTOROLA
User’s Manual — M68ICS08KX In-Circuit Simulator
Section 3. Support Information
3.1 Introduction
This section includes data and information that may be useful in the design,
installation, and operation of your application.\
3.2 MCU Subsystem
The MCU subsystem consists of the MC68HC908KX8 microcontroller, clock
generation and selection, monitor mode control logic that places and holds the
KXICS in monitor mode, the bus voltage level translation buffers, and
processor operating voltage variable regulator.
The MCU, an MC68HC908KX8, is available in two different packages:
•
16-pin SOIC (small-outline integrated circuit)
•
16-pin DIP (dual inline pack)
Only one socket may be used at a time.
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Support Information
31
Support Information
Depending on the connection, the MCU is used in one of three operating modes:
•
In the KXICS socket for programming and simple simulation
•
In the KXICS socket and connected to the target for emulation
•
On the target for MON08 debug operation
3.3 Level Translation
NOTE:
For the following discussion on the theory of operation of the KXICS, refer to
the schematic diagrams in Paragraph 3.6, Figures 3-1 to 3-6 of this section.
The KXICS has an operation voltage range of +2.0 to +5.0 volts while the host
development system interface is an RS-232 (COM) port. U12 on the ICS
converts 5-volt logic signals to RS-232 levels. ICS U10–U13 translate 5-volt
logic levels to the MCU operating voltage (2.0–3.3 volts).
3.4 KXICS Theory of Operation
NOTE:
For the following discussion on the theory of operation of the KXICS, refer to
the schematic diagrams in Paragraph 3.7.
3.4.1 Power Supply
Power input, J2, to the KXICS is via a standard DC power receptacle with a
2.5mm center pin. Input voltage is 5Vdc provided by a plug in the DC power
adapter.
The power is fused to prevent catastrophic failure by fuse F1 (5x20mm or 3AG
fuse).
CAUTION:
Always use a fuse of the proper current and voltage rating. Failure to do so can
result in serious equipment damage
In addition, the input line has a Transient Voltage Suppression (TVS) diode to
stop high voltage transients, including ESD events, from damaging the board.
A green LED is provided to indicate that 5VDC is being provided to the board,
with the ON/Off switch in the ON position. Power, however, is not available to
User’s Manual
32
M68ICS08KX In-Circuit Simulator
Support Information
MOTOROLA
Support Information
KXICS Theory of Operation
the rest of the board until the signal DTR is active high on pin 4 of the serial
connector, J6.
Test points are provided for common (TP1), power input VDD (TP3), switched
main power VDD_SW (TP5), power to the MCU VDD_MCU (TP4), and VTST
(TP2).
3.4.1.1 Main Switched Power
Power to the MCU sockets and circuitry is switched on and off using the DTR
signal into the serial interface (J6). When DTR is low, the power to the MCU
socket is off, and the amber LED is off. When DTR is asserted high, transistor
Q3 will turn on FET Q2 which provides power to the MCU circuitry. if W2 is
selected positions 1 and 2. VTST voltage is sent to the MCU along with the reset
signal being held low briefly following power-up. The MCU is forced to
power-up in the Monitor Mode.
NOTE:
The source of power for the MCU is selected by jumper2. Refer to Section 2,
Table 2-1.
The amber LED, DS2, lights when there is power to the MCU socket.
CAUTION:
There is no over-current protection on the board protecting against
catastrophic failures if the MCU is powered from the target. Equipment damage
can result.
The power to the MCU is selected by jumper W2. With the jumper in the 5V
position, the MCU will be powered by the 5V circuitry, i.e., from the plug in the
power supply). With W2 in the LO V position, the MCU will be powered by the
on-board low voltage regulator (U6). The low voltage is selected by jumper W1
which has preset voltages of 3.3V, 3.0V, 2.7V, 2.2V, 2.0V, and a poteniometer
for adjusting the voltage.
CAUTION:
The MCU may be set to operate at a variety of voltages. Ensure the selected
voltage matches the voltage of the target. Failure to do so can result in
equipment damage.
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Support Information
33
Support Information
3.4.1.2 VTST Power
VTST is created by a voltage regulator, MC34063, nominally set for 8.6VDC.
This keeps the worst case voltage at greater than VDD +3VDC, meeting VTST
voltage minimums. The voltage may be monitored at VTST test point TP2.
VTST is used during start-up to force the MCU into the Monitor Mode.
3.4.1.3 Reset on Power-up
At initial power-on to the MCU, there is a delay of a few hundred milliseconds
during which the signal ICS_RST# is held low, as set by U8 (DS1233).
When ICS_RST# goes high, the binary ripple counter, U3, begins counting
clock cycles, at the 9.8304MHz rate of the clock Y1. After 1024 clock cycles
are counted, the DELAY_RESET signal toggles and the counter stops counting.
The delayed reset signal is used to turn-on communications to the MCU and to
hold several MCU pins in appropriate states to force Monitor Mode on
power-up.
3.4.2 Serial Communications
Serial communication in half-duplex mode, using PTA0 for transmit and
receive, to the MCU is via the DE9 connector, J6. Pin 2 is the path for transmit
signals and pin 3 is for receive signals. Pin 4, the DTR signal, is utilized as an
input to provide the software host with the ability to turn MCU power on and
off. The RTS signal on contact 7 is used as an input to provide the software host
with the ability to control the IRQ* high voltage.
Serial communication to the MCU does not occur until DELAY_RESET
becomes active high 1024 clock cycles after the RESET signal is high (para
3.4.1.3).
3.4.3 Clock Selection
The source of timing for the MCU may be either the KXICS board’s clock Y1
or the MCU’S internal clock. Selection is by jumper header W-4 (Table 2-1).
User’s Manual
34
M68ICS08KX In-Circuit Simulator
Support Information
MOTOROLA
Support Information
KXICS Theory of Operation
When the jumper is set for the PTB6 position, the MCU runs from it’s internal
clock and pin PTB6 of the MCU is connected to the target connector.
When the jumper is set for the CLK position, the Y1 external clock signal from
the KXICS board is applied to the PTB6 pin of the MCU for timing. (An internal
MCU register must be set to control the selection of internal or external clock.)
The external clock, Y1, has an output frequency of 9.8304 MHz to allow the
MCU to communicate at 9600 baud. It is socketed to allow the use of a full-size
or half-size clock. You may change clock frequencies by installing a new clock
chip, however the serial communication rate proportionally changes. W3 may
be used to disable the external clock.
Additionally, the on-board clock is available as an output on the 3-pin header J4
for target or computer host clock synchronization.
3.4.4 Start-Up in Monitor Mode
Following power up the ICS_RST# is held low for a period of time by U8.
When ICS_RST* is asserted high, the binary ripple counter, U3, counts up 1024
clock cycles prior to allowing DELAY RESET to be asserted. The delayed reset
controls the analog switch, U7, connected to PTA1 and PTB[0...1]. The RTS
signal is held high which places the VTST voltage as the high voltage for IRQ*.
Analog switch, U7, connects PTA1 to common, PTB0 to VDD_MCU, and PTB1
to common until DELAY_RESET is asserted. VTST is held above VDD-MCU
+3Vdc during the reset release forcing the KXICS board to power up in the
Monitor Mode.
Following the counter time-out, the analog switch, U7, is toggled so that the
PTA1 and PTB[0...1] pins of the board are connected to the target head
connectors.
Following entry into monitor mode, you may switch the IRQ* voltage to
VDD_MCU by setting RTS low. The analog switch, U14, will switch the
connection of MCU pin 9 from the ICS reset circuitry to a connection to the
target head connector. Be aware that beside disabling the use of external resets
of the MCU, internal MCU features, e.g., the COP must be serviced properly in
this mode.
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Support Information
35
Support Information
3.5 KXICS Connector Signal Definitions
The tables in this section describe the pin assignments for the connectors on the
KXICS board.
3.5.1 Target Flex Cable Interface Connector J1
Table 3-1 J1 Target Flex Connector Pin Assignments
Pin
No.
Schematic
NET
1
N/C
2
N/C
3
N/C
4
PTB7
5
N/C
6
PTB6
7
N/C
8
PTB5
9
N/C
10
PTB4
11
N/C
12
N/C
13
N/C
14
Direction
Signal Description
Bidirectional
Port B I/O
Bidirectional
Port B I/O
Bidirectional
Port B I/O
Bidirectional
Port B I/O
PTB3
Bidirectional
Port B I/O
15
TGT_PTA0
Bidirectional
Port A I/O
16
PTB2
Bidirectional
Port B I/O
17
TGT_PTA1
Bidirectional
Port A I/O
18
TGT_PTB1
Bidirectional
Port B I/O
19
PTA2
Bidirectional
Port A I/O
20
TGT_PTB0
Bidirectional
Port B I/O
21
PTA3
Bidirectional
Port A I/O
22
N/C
User’s Manual
36
M68ICS08KX In-Circuit Simulator
Support Information
MOTOROLA
Support Information
KXICS Connector Signal Definitions
Pin
No.
Schematic
NET
Direction
23
PTA4
Bidirectional
24
N/C
25
N/C
26
N/C
27
N/C
28
N/C
29
Common
30
Common
31
Common
32
Common
33
Common
34
Common
35
Common
36
Common
37
Common
38
Common
39
Common
40
Common
Signal Description
Port A I/O
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Support Information
37
Support Information
3.5.2 Target Ribbon Interface Connector J5
The KXICS includes a connector, J5 (Table 3-2), which allows a convenient
connection to the target, using a 16-pin ribbon cable.
Table 3-2 J5 Target Connector Pin Assignments
Pin
No.
Schematic
NET
1
Common
2
PTA1
Bidirectional
Port A I/O
3
PTA0
Bidirectional
Port A I/O
4
IRQ*
In
5
PTB0
Bidirectional
Port B I/O
6
PTB1
Bidirectional
Port B I/O
7
PTB2
Bidirectional
Port B I/O
8
PTB3
Bidirectional
Port B I/O
9
PTB7
Bidirectional
Port B I/O
10
OSC1/PTB6
Bidirectional
Clock signal from xtal or MCU/Port B I/O
11
PTB5
Bidirectional
Port B I/O
12
PTB4
Bidirectional
Port B I/O
13
PTA2
Bidirectional
Port A I/O
14
PTA3
Bidirectional
Port A I/O
15
PTA4
Bidirectional
Port A I/O
16
VDD
Direction
Signal Description
Target interrupt request to MCU
KXICS Supply Voltage
User’s Manual
38
M68ICS08KX In-Circuit Simulator
Support Information
MOTOROLA
Support Information
KXICS Connector Signal Definitions
3.5.3 Target MONO8 Interface Connector J3
The MONO8 interface connector, J3 (Table 2-6), is used when the MCU is
mounted on the target. Refer to Section 4 Using the MONO8 for detailed
information.
Table 3-3 J3 MONO8 Target Connector Pin Assignments
Pin
No.
Schematic
NET
Direction
1
RST_OUT*
Out
2
Common
3
RST_IN*
In
4
RST*
Out
5
TGT_IRQ*
In
6
IRQ*
Out
Interrupt Request
7
TGT_PTA0
Bidirectional
Port A I/O - bit 0
8
PTA0
Bidirectional
Port A I/O - bit 0
9
TGT_PTA1
Bidirectional
Port A I/O - bit 1
10
PTB1
Bidirectional
Port B I/O - bit 1
11
TGT_PTB0
Bidirectional
Port B I/O - bit 0
12
PTB0
Bidirectional
Port B I/O - bit 0
13
TGT_PTB1
Bidirectional
Port B I/O - bit 1
14
PTB1
Bidirectional
Port B I/O - bit 1
15
No connect
16
No connect
Signal Description
To reset target
From target to reset MCU and Ripple Counters
Forced reset to target
Target Interrupt request to MCU
3.5.4 Power Connector
Power connector, J2, (Table 3-4) is used to connect to a source power supply for the KXICS.
Table 3-4 Power Connector J2 Pin Assignments
Pin
No.
Mnemonic
Signal
1
VCC
+5 VDC POWER — Input voltage (+5 Vdc @ 1.0 A) from the provided
power supply used by the KXICS logic circuits
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Support Information
39
Support Information
3.5.4 Power Connector
Power connector, J2, (Table 3-4) is used to connect to a source power supply for the KXICS.
Table 3-4 Power Connector J2 Pin Assignments
Pin
No.
Mnemonic
2
GND
Common
3
GND
Common
Signal
3.5.5 RS-232C Communication Connector, J6
The RS-232C Communication Connector, J6, (Table 3-5) provides connection to the host computer.
Table 3-5 RS-232C Communication Connector J6 Pin Assignments
Pin
No.
Mnemonic
2
RXD
RECEIVE DATA — Output for sending serial data to the DTE device
3
TXD
TRANSMIT DATA — Input for receiving serial data output from the DTE
device
4
DTR
DATA TERMINAL READY — Switches the KXICS to apply power to
the MCU and related circuitry
5
GND
Common
7
RTS
Controls whether voltage for IRQ* high is VTST or VDD_MCU.
Signal
User’s Manual
40
M68ICS08KX In-Circuit Simulator
Support Information
MOTOROLA
Support Information
Parts List
3.6 Parts List
Table 3-6. KXICS Parts List (Rev F)
Reference
Designator
Description
Manufacturer
Part Number
Printed Circuit Board Assembly
01-RE10080W01
Test Procedure, ICS08KX
12ASE10080W
Test Fixture, ICS08KX
81ASE10080W
Printed Wiring Board, ICS08KX
84-RE10080WO1
Feet Rubber 0.5" Tapered
squares
FASTEX
4009-00-5072
Cap 47 uF Tantalum low ESR 16V
AVX
TPSD476M016R0150
Cap 0.2 uF Ceramic Z5U 50V
0805
AVX
08055E104ZAT2A
Cap 10 uF Tantalum 16V
AVX
TAJC106M016
Cap 560 pF Ceramic COG 50V
0805
AVX
08055A561KAT2A
D3, D4
Diode, Schottky, MBRA130
Motorola/ON Semi
MBRA130
D1, D5
Diode, TVS, 1SMA6.OAT3
Motorola/ON Semi
1SMA6.OAT3
D2, D6
Diode, Schottky, MBR0520
Motorola/ON Semi
MBR0520
DS1
LED Green, LED_1206
Lumex
SML-LX1206GC
DS2
LED Amber, LED_1206
Lumex
SML-LX1206YC
F1
Fuse 0.5A 250V 5x20mm Fast
Schurter
0034.1523
J2
Conn Pwr Jack RT ANG 2.5mm
Center Pin
CUI Stacck
PJ-202B
J6
Conn DE9, Socket, R/A
Cinch
DEKL-9SATI-F
J4, W2-W4
Hdr, 3x1, 100, JPR_3
3M
2403-6112TB
J3
Hdr, 8x2, 100, SHRD
3M
2516-6002-UG
J1
Hdr, 2x20, 0.100.SHRD
3M
2540-6002-UG
J5
SKT 16 Pin DIP
Augat
816-AG11D
L2
IND, 180uH, SMT
Murata
LQH4N181K04
L1
ind, 10uH, SMT
Murata
LQH1N100K04
Q2
XSTR PFET MMFT5P02 SOT223
Motorola/ON Semi
MMFT5P02HD
C8, C9, C28
C2-C7,C11-C16,
C19-C27
C1, C17, C18
C10, C29
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Support Information
41
Support Information
Table 3-6. KXICS Parts List (Rev F)
Reference
Designator
Description
Manufacturer
Part Number
Q3, Q5-6
XSTR NPN MMBT3904 SOT23
Motorola/ON Semi
MMBT3904
Q1, Q4
XSTR PFET MMBF0201 SOT23
Motorola/ON Semi
MMBF0201
R16
Res, 150 ohm, 1%, 0805
Dale
CRCW08051500F
R34
Res, 124 ohm, 1%, 0805
Dale
CRCW08051240F
R33
Res, 205 ohm,!5, 0805
Dale
CRCW08052050F
R32
Res, 75 ohm, 1%, 0805
Dale
CRCW080575R0F
Res, 1.21K, 1%, 0805
Dale
CRCW08051211F
R29
Res, 499 ohm, 1%, 0805
Dale
CRCW08054990F
R30
Res, 169 ohm, 1%, 0805
Dale
CRCW08051690F
R32
Res, 118 ohm, 1%, 0805
Dale
CRCW08051180F
R1, R13, R15
Res, 10 ohm, 1%, 1206
Dale
CRCW120610R0F
Res, 100k, 5%, 0805
Dale
CRCW0805104J
Res, 33 ohm, 5%, 0805
Dale
CRCW08055330J
Res, 3.3K, 5%, 0805
Dale
CRCW0805332J
R18
Res, 59K ohm, 1%, 0805
Dale
CRCW08055902F
R4-R6, R8-R12, R14,
R19-R21, R24, R27,
R28, R36, R37, R50,
R54-R56, R58-R59
Res, 10 K ohm, 5%, 0805
Dale
CRCW0805103J
R3, R35, R52, R57
Res, 470 ohm, 5%, 0805
Dale
CRCW0805471J
R53
Res, 330 ohm, 5%, 0805
Dale
CRCW0805331J
R60
Res, 33K ohm, 5%, 0805
Dale
CRCW0805333J
RV1
Res, VAR 2K SMT_4MM
Bourns
3214W-202W
SW1
Switch, SPDT RT ANG
C&K
ET01MD1AVQE
IC Hex Inverter OC 74HC05
14SOIC
Motorola/ON Semi
MC74HC05D
U8
IC 5V Supervisor SOT-223
Dallas Semi
DS1233Z-5
U1
IC Microcontroller KX8 DIP16
Motorola
PC68HC908KX8DW
U2
IC UHS 2 Input OR SOT23-5
Fairchild
NC7SZEWM5
R17, R23
R25
R26, R38-R49, R51
R2, R7, R22
U4, U11, U13
User’s Manual
42
M68ICS08KX In-Circuit Simulator
Support Information
MOTOROLA
Support Information
Parts List
Table 3-6. KXICS Parts List (Rev F)
Reference
Designator
Description
U7, U14
IC Triple 2:1 Analog MUX 16SOIC
Motorola/ON Semi
MC74HC4053D
U9
IC Quad Nand 14SOIC
Motorola/ON Semi
MC74ACOOD
U10
IC Buffer Tri-State 14SOIC
Fairchild
MC74ACT1125D
U5
IC DC-DC Converter SO-8
Motorola/ON Semi
MC34063AD
U6
IC Var Regulator LT1086
DD_PACK
Linear Tech.
LT1086CM
U12
IC Low Power RS232 Driver
16SOIC
Linear Tech
LT1181ACSW
U15-16
Optocoupler 50% CTR DIP-4
PS2501-1
NEC
PS2501-1
W1
Hdr 2x6 0.100 JPR_2X6
3M
1412-6122TB
XF1
Holder Fuse 5x20 & 3AG
Schurter
0GD 0031.8231
XU1
SKT AIP 16 POS DIP
3M Textool
216-3340-00-0602JJ
XW1-XW4
Shunt w/Handle
AMP
881545-1
XY1
SKT 14 pin DIP
Augat
814-AG11D
Xtal, 9.8304Mhz, 1/2 size DIP
Epson
SG-532P-9.8302MC
Y1
Manufacturer
M68ICS08KX In-Circuit Simulator
MOTOROLA
Part Number
User’s Manual
Support Information
43
Support Information
3.7 KXICS Board Layout and Schematics Diagrams
Figure 3-1 KXICS Board Layout
User’s Manual
44
M68ICS08KX In-Circuit Simulator
Support Information
MOTOROLA
D
C
B
A
4.
SPECIAL SYMBOL USAGE:
3.
1
Power Conditioning/Switching
Page 2
Power ON
COMM PORT (DSub9)
Page 3
2
RTS
Oscillator
Page 3
Tx/Rx
INTERPRET DIAGRAM IN ACCORDANCE WITH
ANSI SPECIFICATIONS WITH THE
EXCEPTION OF LOGIC BLOCK SYMBOLOGY.
[ ] DENOTES VECTORED SIGNAL.
# DENOTES ACTIVE LOW SIGNAL.
DEVICE TYPE NUMBER IS FOR REFERENCE
ONLY THE NUMBER VARIES WITH THE
PART MANUFACTURER.
CAPACITORS ARE IN MICROFARADS, 50V
RESISTORS ARE IN OHMS, 5%, 1/10W
UNLESS OTHERWISE SPECIFIED:
2.
1.
2
MCU Socket
Page 5
Busses PTA, PTB
3
3
RST/IRQ Logic and Control
Page 3 & 4
MON08 Connector & Circuit
Page 4
TGT_PTA0-1,
TGT_PTB0-1
Target Connectors
Page 5
4
4
5
5
3
14
7
5
14
7
13
14
11
9
10
12
6
4
13
8
11
9
74HC05
U13F
74HC05
U13E
74HC05
U13D
APPROVED:
CHECKED:
DRAWN:
A. Okunami
TEAM Dev. / WRR
6
DATE:
22-Jun-00
DATE:
19 Nov 99
DATE:
Modify power circuitry - Vtst on
when board powered.
Change value of R23
Change wiring of J5 per customer
request. J5 wiring now resembles
J1.
D
E
F
B
Size
Dwg.
No.
7
63BSE10080W
ENG
8
Sheet
1
of
5
F
Rev:
AUSTIN, TX 78735 USA
IN CIRCUIT SIMULATOR - ICS08KX
6501 WILLIAM CANNON DRIVE WEST
17July00
26JUNE00
5JUNE00
24MAY00
19APR00
Last Update 17 July 00
74ACT125
U10D
11
Modify IRQ# voltage select. Change
input signal to U4A. Change RST#
voltage. Added RTS_RESET
C
12
Add switch to PB7/RST#
B
VDD_SW
Initial Release
A
VDD
5JAN00
Design Review Changes Included
24JAN00
3JAN00
TBD
DATE
Ready for Design Review
8
O
DESCRIPTION
Initial Concepts
7
E0.0
REV
Software and Development Systems
Title:
8
10
12
SPARE GATES
THIS DOCUMENT CONTAINS INFORMATION
PROPRIETARY TO MOTOROLA AND SHALL NOT BE
USED FOR ENGINEERING DESIGN, PROCUREMENT
OR MANUFACTURE IN WHOLE OR IN PART WITHOUT
CONSENT OF MOTOROLA.
74HC05
U11F
74HC05
U11E
74HC05
U11D
74HC05
U11C
74HC05
U11B
VDD_MCU
6
7
14
7
14
1
14
7
7
14
7
13
14
7
14
7
NOTES:
PTA0-1, PTB0-1
D
C
B
A
D
C
B
TP1
COMMON
1
VDD
C5
0.1uF
C21
0.1uF
C28 +
47uF, 16V
GND
VCC
C4
0.1uF
2
2
C13
0.1uF
1
3
D4
MBRA130
SW1
C6
0.1uF
POWER_ON
Page 3
4
F1 0.5A, 250V
3
D1
1SMA6.0AT3
2
1
C11
0.1uF
TP3
5VDC IN
10K
R20
R3
470
C3
0.1uF
DS1
GREEN
3
R19
10K
C27
0.1uF
3
Q3
MMBT3904
2
4
R15
10, 1%, 1/4W
Q2
MMFT5P03HD
S
1
C14
0.1uF
VDD_SW
C20
0.1uF
VDD_MCU
3
5VDC INPUT
J2
PWR_JACK
2
A
1
VDD
3
4
+
C7
0.1uF
R1
10, 1%, 1/4W
3
C16
0.1uF
1
R33
205, 1%
ADJ
VOUT
VOUT(TAB)
LT1086
R17
1.21K, 1%
VIN
U6
TP5
5VDC SWITCHED
C17
10uF, 16V
VDD_SW
+ C8
47uF, 16V
R13
10, 1%, 1/4W
4
2
4
5
6
7
8
L2
180 uH
MC34063
GND
CAP
SW EMIT
SW COL
R29
499, 1%
5
R34
124, 1%
4
3
2
1
R30
169, 1%
D3
6
R32
R31
118, 1%
75, 1%
6
1.8V
2
3.2V
LO V
VOLTAGE SELECT
W2
5V
C10
560 pF
MBRA130
W1
LOW VOLTAGE SELECT
1.25V REFERENCE
COMPARE
VCC
SENSE
DR COL
U5
R16
150, 1%
5
R14
10K
L1
10 uH
RV1
2K
10K
R36
C18
10uF, 16V
R37
10K
+
VDD_MCU
Last Update 17 July 00
Q5
MMBT3904
R35
470
DS2
AMBER
VDD_SW
R2
3.3K
B
Size
8
VTST
Page 4
TP2
8.6VDC +/-0.4V TEST
+ C1
10uF, 16V
Dwg.
No.
7
63BSE10080W
8
Sheet
2
of
5
F
Rev:
AUSTIN, TX 78735 USA
IN CIRCUIT SIMULATOR - ICS08KX
6501 WILLIAM CANNON DRIVE WEST
Title:
D5
1SMA6.0AT3
TP4
C2
0.1uF
7
Software and Development Systems
+ C9
47uF, 16V
R18
59.0K, 1%
1
2
CW
1
2
4
6
8
10
12
3.3V
3.0V
2.7V
2.2V
2.0V
1
3
5
7
9
11
ADJ
G
3
D
D
C
B
A
D
C
B
A
C15
0.1uF
VDD_SW
VDD_SW
1
1
6
2
7
3
8
4
9
5
GND
GND8
VCC
Y1
ENABLE
OUTPUT
OUTPUT8
1
8
11
RTS
7
TX_OUT
2
VDD
16
TR1 OUT
TR2 OUT
RX2 IN
RX1 IN
V-
V+
U12
VDD_SW
14
8
13
6
2
DTR
9.8304MHz
1
0.1uF
RX_IN
XTAL EN
W3
0
C25
0.1uF
SOCKETED TO ALLOW FULL
OR HALF SIZE XTAL
7
4
14
10K
R27
J6
CONNECTOR DSub9
C23
9
VDD_SW
33K
R60
11
10
9
12
5
RST_OUT#
Page 4
74ACT125
8
U10C
3
3
1
74HC05
U4A
VDD_SW
74HC05
U4B
VDD_SW
Q6
MMBT3904
R59
10K
VDD_SW
0.1uF
0.1uF
R55
10K
VDD
4 C26
3
1 C24
D6
MBR0520
TR1 IN
TR2 IN
RX2 OUT
RX1 OUT
C2-
C2+
C1-
C1+
LT1181A
2
4
R9
10K
VDD_SW
R53
330
VDD_MCU
RTS_RESET
Page 4
3
1
9.8304MHz
Page 5
C22
0.1uF
4
4
74HC05
U13A
VDD
74HC05
U13B
VDD
4
2
2
1
74AC00
U9A
VDD_SW
R54
10K
74HC05
U13C
VDD
5
VDD
R56
10K
VDD
5
3
6
33
9
10
6
U4C
J4
8
6
5
U10B
6
10
2
74HC05
U11A
9
7
6
5
3
2
4
13
12
14
15
1
7
13
74HC05
U4D
VDD_SW
PTA0
12
B
Size
Dwg.
No.
7
63BSE10080W
8
Sheet
3
of
5
F
Rev:
AUSTIN, TX 78735 USA
IN CIRCUIT SIMULATOR - ICS08KX
6501 WILLIAM CANNON DRIVE WEST
Title:
DELAY_RESET
Page 4
8
Last Update 17 July 00
R10
10K
VDD_SW
PTA[0..4]
Page 4,5
Software and Development Systems
Q1
Q2
Q3
Q4
Q5
Q6
Q7
Q8
Q9
Q10
Q11
Q12
74HC4040
1
VDD_MCU
R50
10K
VDD_MCU
VDD_SW
CLK
U3
R11
10K
VDD_SW
74ACT125
VDD_SW
5
VDD_SW
74HC05
74AC00
U9C
VDD_SW
R26
100K
R12
10K
VDD_SW
R25
R28
10K
VDD_SW
POWER_ON
Page 2
6
5
4
3
14
VCC
GND
14
7
14
7
14
7
2
10
14
7
15
14
7
14
7
16
VCC
14
7
1
14
7
14
7
RST
11
7
14
7
GND
8
14
7
D
C
B
A
D
C
B
R23
TGT_PTB[0..1]
Page 5
1
1.21K, 1%
VDD_MCU
DELAY_RESET
Page 3
TGT_PTA1
Page 5
TGT_PTA0
Page 5
RST_OUT#
Page 3
R8
10K
VDD_SW
TGT_PTB1
TGT_PTB0
R6
10K
3
5
1
2
13
12
9
10
11
6
RST_OUT#
RST_IN#
TGT_IRQ#
TGT_PTA0
TGT_PTA1
TGT_PTB0
TGT_PTB1
R5
10K
1
3
5
7
9
11
13
15
J3
Z1
Z0
Y1
Y0
X1
X0
C
B
A
EN
Z
Y
X
74HC4053
2
4
6
8
10
12
14
16
GND2
GND
VCC
U8
PTA1
PTB0
PTB1
15
4
RST#
IRQ#
PTA0
PTA1
PTB0
PTB1
14
10
VDD_SW
4
1
3
74HC05
U4E
MON08
VDD_SW
U7
2
D2
14
11
MBR0520
C12
0.1uF
VDD_SW
10K
R21
RST*
3
DS1233
3
2
PTB[0..7]
Page 5
2
1
74AC00
4
4
RTS_RESET
Page 3
4
13
12
U9D
VDD_SW
NC7SZ32
U2
VDD_SW
5
3
14
7
2
16
VCC
11
9
RST#
PTB7
3
5
1
2
13
12
9
10
11
6
74HC05
U4F
VDD_SW
R4
10K
14
7
8
Z1
Z0
Y1
Y0
X1
X0
C
B
A
EN
U14
5
Z
Y
X
74HC4053
VDD_SW
Q1
MMBF0201
R7
3.3K
5
4
15
14
R24
10K
VDD_SW
R58
10K
VDD_MCU
C29
560 pF
VDD_MCU
VTST
Page 2
2
2
3
6
MCU_PIN9
Page 5
Q4
MMBF0201
R22
3.3K
PS2501-1
1
4
U16
PS2501-1
1
3
U15
4
470
R52
470
R57
74AC00
U9B
5
4
74ACT125
U10A
3
B
Size
RTS_RESET
Page 3
Dwg.
No.
7
63BSE10080W
8
Sheet
4
of
5
F
Rev:
AUSTIN, TX 78735 USA
IN CIRCUIT SIMULATOR - ICS08KX
6501 WILLIAM CANNON DRIVE WEST
Title:
8
Last Update 17 July 00
2
VDD_SW
Software and Development Systems
PTA[0..4]
Page 3,5
IRQ#
Page 5
6
VDD_SW
7
1
6
14
7
A
1
16
VCC
7
GND
NC
8
7
GND
NC
8
7
14
7
D
C
B
A
D
C
B
A
IRQ#
Page 4
1
MCU_PIN9
Page 4
1
33
R42
C19
0.1uF
2
VDD_MCU
2
VSS
PTB7
PTB6
PTB5
PTB4
PTB3
PTB2
PTB1
PTB0
PTA4
PTA3
PTA2
PTA1
PTA0
SKT_16pdip
IRQ1#
VDD
XU1
9
10
11
12
8
7
6
5
15
14
13
2
3
1
4
16
VSS
PTB7
PTB6
PTB5
PTB4
PTB3
PTB2
PTB1
PTB0
PTA4
PTA3
PTA2
PTA1
PTA0
SKT_16pdip
IRQ1#
VDD
J5
33
33
33
PTB3
PTB4
PTB5
PTB6
7
8
12
11
10
3
PTB2
PTB7
TGT_PTB1
9
TGT_PTB0
PTA4
15
33
33
33
33
33
6
PTA3
14
33
33
5
PTA2
R49
R47
R45
R51
R48
R46
R44
33
R39 33
R41
R43
R38
R40
13
2
3
RIBBON CABLE
1
4
16
68HC908KX8
3
OSC1/PTB6
PTB5
PTB4
PTB3
PTB2
PTB1
PTB0
PTA4
PTA3
PTA2
PTA1
PTA0
CLK
PTB6 SEL
W4
PTB6
4
4
PTA2
PTA3
PTA4
PTA[0..4]
Page 3,4
5
TGT_PTB[0..1]
Page 4
PTA[0..4]
Page 3,4
TGT_PTA1
Page 4
TGT_PTA0
Page 4
9.8304MHz
Page 3
TGT_PTA1
Page 4
TGT_PTA0
Page 4
5
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
HEADER 20X2
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
J1
6
IRQ#
Page 4
PTB3
PTB2
TGT_PTB1
TGT_PTB0
PTB7
PTB6
PTB5
PTB4
FLEX TARGET CABLE
6
MH1
FID1
MH2
FID2
B
Size
Dwg.
No.
7
63BSE10080W
8
Sheet
5
of
5
F
Rev:
AUSTIN, TX 78735 USA
MH4
IN CIRCUIT SIMULATOR - ICS08KX
6501 WILLIAM CANNON DRIVE WEST
Title:
FID3
8
MH3
Reference
Software and Development Systems
Last Update 17 July 00
PTB[0..7]
Page 4
TGT_PTB[0..1]
Page 4
7
D
C
B
A
User’s Manual — M68ICS08KX In-Circuit Simulator
Section 4. Using the MON08 Interface
4.1 Introduction
The MON08 debugging interface may be used to debug and program a target
system’s MCU directly. The target system must be connected to the
M68ICS08KX in-circuit simulator board’s MON08 interface connector. This
section explains how to connect to the MON08 interface on the target board.
4.2 Target System Header Placement and Layout
Two headers must be placed on the target board:
•
P1 — 16-pin header such as Berg Electronics part number 67997-616
•
P2 — 1-pin header such as Berg Electronics part number 68001-601
Table 4-1 shows the target-system interconnections for J3.
Table 4-1. MON08 Target System Connector J3
Pin
No.
M68ICS08KX8
Label
Direction
1
RST-OUT
Out to target
2
GND
Ground
3
RST-IN
In from target
Connect to all logic that generates resets.
4
RST
Bidirectional
Connect to MCU RST pin and P1 pin 1. No other target-system
logic should be tied to this signal. It will swing from 0 to +5 Vdc.
5
TGT-IRQ
In from target
Connect to logic that generates interrupts.
6
IRQ
Out to target
Connect to MCU IRQ pin. No other target-system logic should be
tied to this signal. It will swing from 0 to +8.6 Vdc.
7
TGT-PTA0
Bidirectional
Connect to user circuit that would normally be connected to PTA0
on the MCU. This circuit will not be connected to the MCU when
the in-circuit simulator is being used.
Target System Connection
Connect to logic that is to receive the RST signal.
Connect to common (VSS).
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Using the MON08 Interface
45
Using the MON08 Interface
Table 4-1. MON08 Target System Connector J3 (Continued)
Pin
No.
M68ICS08KX8
Label
Direction
Target System Connection
8
PTA0
Bidirectional
Connect to MCU PTA0 pin. No other target-system logic should be
tied to this signal. Host I/O present on this pin.
9
TGT-PTA1
Bidirectional
Connect to user circuit that normally would be connected to PTA1
on the MCU.
10
PTA1
Bidirectional
Connect to MCU PTA1 pin. No other target-system logic should be
tied to this signal. Grounded during power-on reset and for 256
cycles after reset.
11
TGT-PTB0
Bidirectional
Connect to user circuit that normally would be connected to PTB0
on the MCU.
12
PTB0
Bidirectional
Connect to MCU PTB0 pin. No other target-system logic should be
tied to this signal. Held at +5 Vdc during power-on reset.
13
TGT-PTB1
Bidirectional
Connect to user circuit that normally would be connected to PTB1
on the MCU.
14
PTB1
Bidirectional
Connect to MCU PTB1 pin. No other target-system logic should be
tied to this signal. Grounded during power-on reset.
15
NC
NC
Not connected
16
NC
NC
Not connected
4.3 Connecting to the In-Circuit Simulator
Using the 16-pin cable provided with the KXICS kit, connect one end of the
cable to the KXICS board at J3. Connect the other end to connector P1 on the
target-system board. The pin-1 indicators on each cable end must correspond to
the pin-1 indicators on the headers. P2 is not used when connecting to the
KXICS board.
User’s Manual
46
M68ICS08KX In-Circuit Simulator
Using the MON08 Interface
MOTOROLA
User’s Manual — M68ICS08KX In-Circuit Simulator
Appendix A. S-Record Information
A.1 Introduction
The Motorola S-record format was devised to encode programs or data files in
a printable format for transport between computer platforms. The format also
provides for editing of the S records and monitoring the cross-platform transfer
process.
A.2 S-Record Contents
Each S record is a character string composed of several fields which identify:
•
Record type
•
Record length
•
Memory address
•
Code/data
•
Checksum
Each byte of binary data is encoded in the S record as a 2-character hexadecimal
number:
•
The first character represents the high-order four bits of the byte.
•
The second character represents the low-order four bits of the byte.
The five fields that comprise an S record are shown in .
Table A-1. S-Record Fields
Type
Record
Length
Address
Code/Data
Checksum
The S-record fields are described in .
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
S-Record Information
47
S-Record Information
Table A-2. S-Record Field Contents
Field
Printable
Characters
Type
2
S-record type — S0, S1, etc.
Record
Length
2
Character pair count in the record, excluding the
type and record length.
Address
4, 6, or 8
2-, 3-, or 4-byte address at which the data field is
to be loaded into memory.
0 – 2n
From 0 to n bytes of executable code, memory
loadable data, or descriptive information. For
compatibility with teletypewriter, some programs
may limit the number of bytes to as few as 28
(56 printable characters in the S record).
2
Least significant byte of the one’s complement of
the sum of the values represented by the pairs of
characters making up the record length,
address, and the code/data fields.
Code/Data
Checksum
Contents
Each record may be terminated with a CR/LF/NULL. Additionally, an S record
may have an initial field to accommodate other data such as line number
generated by some time-sharing systems.
Accuracy of transmission is ensured by the record length (byte count) and
checksum fields.
A.3 S-Record Types
Eight types of S records have been defined to accommodate the several needs
of the encoding, transport, and decoding functions. The various Motorola
upload, download, and other record transport control programs, as well as cross
assemblers, linkers, and other file-creating or debugging programs, utilize only
those S records which serve the purpose of the program.
For specific information on which S records are supported by a particular
program, consult the user manual for the program.
User’s Manual
48
M68ICS08KX In-Circuit Simulator
S-Record Information
MOTOROLA
S-Record Information
S Record Creation
NOTE:
The ICS08RKZ supports only the S0, S1, and S9 record types. All data before
the S1 record is ignored. Thereafter, all records must be S1 type until the S9
record, which terminates data transfer.
An S-record format may contain the record types in .
Table A-3. Record Types
Record Type
Description
S0
Header record for each block of S records. The code/data field
may contain any descriptive information identifying the following
block of S records. The address field is normally 0s.
S1
Code/data record and the 2-byte address at which the code/data
is to reside.
S2 – S8
S9
Not applicable to ICS08RKZ
Termination record for a block of S1 records. Address field may
optionally contain the 2-byte address of the instruction to which
control is to be passed. If not specified, the first interplant
specification encountered in the input will be used. There is no
code/data field.
Only one termination record is used for each block of S records. Normally, only
one header record is used, although it is possible for multiple header records to
occur.
A.4 S Record Creation
S-record format programs may be produced by dump utilities, debuggers, cross
assemblers, or cross linkers. Several programs are available for downloading a
file in the S-record format from a host system to an 8- or 16-bit
microprocessor-based system.
A.5 S-Record Example
A typical S-record format, as printed or displayed, is shown in this example:
Example:
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
S-Record Information
49
S-Record Information
S00600004844521B
S1130000285F245F2212226A00042429008237C2A
S11300100002000800082529001853812341001813
S113002041E900084#42234300182342000824A952
S107003000144ED492
S9030000FC
In the example, the format consists of:
•
An S0 header
•
Four S1 code/data records
•
An S9 termination record
A.5.1 S0 Header Record
The S0 header record is described in .
Table A-4. S0 Header Record
Field
S-Record
Entry
Type
S0
S-record type S0, indicating a header record
Record
Length
06
Hexadecimal 06 (decimal 6), indicating six
character pairs (or ASCII bytes) follow
Address
00
00
4-character, 2-byte address field; zeroes
Description
Code/Data
48
44
52
Descriptive information identified these S1
records:
ASCII H
D
R — “HDR”
Checksum
1B
Checksum of S0 record
A.5.2 First S1 Record
The first S1 record is described in .
User’s Manual
50
M68ICS08KX In-Circuit Simulator
S-Record Information
MOTOROLA
S-Record Information
S-Record Example
Table A-5. S1 Header Record
Field
S-Record
Entry
Description
Type
S1
S-record type S1, indicating a code/data record
to be loaded/verified at a 2-byte address
Record
Length
13
Hexadecimal 13 (decimal 19), indicating 19
character pairs, representing 19 bytes of binary
data, follow
Address
0000
4-character, 2-byte address field; hexadecimal
address 0000 indicates location where the
following data is to be loaded
Opcode
Code/Data
Checksum
28
24
22
22
00
29
08
5F
5F
12
6A
04
00
23
Instruction
24
7C
2A
BHCC
BCC
BHI
BHI
BRSET
BHCS
BRSET
$0161
$0163
$0118
$0172
0, $04, $012F
$010D
4, $23, $018C
Checksum of the first S1 record
The 16 character pairs shown in the code/data field of are the ASCII bytes of
the actual program.
The second and third S1 code/data records each also contain $13 (19T)
character pairs and are ended with checksum 13 and 52, respectively. The fourth
S code/data record contains 07 character pairs and has a checksum of 92.
A.5.3 S9 Termination Record
The S9 termination record is described in .
Table A-6. S9 Header Record
Field
S-Record
Entry
Description
Type
S9
S-record type S9, indicating a termination record
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
S-Record Information
51
S-Record Information
Table A-6. S9 Header Record
Field
S-Record
Entry
Description
Record
Length
03
Hexadecimal 04, indicating three character pairs
(three bytes) follow
Address
00
00
4-character, 2-byte address field; zeroes
Code/Data
There is no code/data in an S9 record.
Checksum
FC
Checksum of S9 record
A.5.4 ASCII Characters
Each printable ASCII character in an S record is encoded in binary. gives an
example of encoding for the S1 record. The binary data is transmitted during a
download of an S record from a host system to a 9- or 16-bit
microprocessor-based system. For example, the first S1 record in is sent as
shown here.
TYPE
S
5
LENGTH
1
3
3
1
1
3
ADDRESS
3
1
3
0
3
3
0
0
3
CODE/DATA
0
0
3
0
0
3
2
0
3
8
2
3
5
8
3
F
5
4
6
0101 0011 0011 0001 0011 0001 0011 0011 0011 0000 0011 0000 0011 0000 0011 0000 0011 0010 0011 1000 0011 0101 0100 0110
User’s Manual
52
...
CHECKSUM
...
2
...
...
3
A
2
4
1
0011 0010 0100 0001
M68ICS08KX In-Circuit Simulator
S-Record Information
MOTOROLA
User’s Manual — M68ICS08KX In-Circuit Simulator
Appendix B. Quick Start Hardware Configuration Guide
B.1 Introduction
This quick start guide explains the:
•
Configuration of the M68ICS08KX in-circuit simulator (KXICS) board
•
Installation of the hardware
•
Connection of the board to a target system
There are four methods for configuring the KXICS: standalone, simulation,
evaluation, and programming.
ESD CAUTION:
•
Standalone — ICS08KXZ.exe is running on the host computer (the
KXICS is not connected). Emulation of the MC68HC908KX8 MCU
CPU, registers, and I/O ports is within the host computer environment.
•
Simulation — Host computer is connected to the KXICS via the RS-232
cable, and the ICS08KXZ.exe is running on the host computer. This
provides access to the MC68HC908KX8 MCU, internal registers, and
I/O ports.
•
Evaluation — Host computer is connected to the KXICS, and the KXICS
is connected to the target system via the flex cable. This method provides
limited real-time evaluation of the MCU and debugging user developed
hardware and software.
•
Programming — Host computer is connected to the KXICS, and the
KXICS is connected to the target system via the MON08 cable. Use the
PROG08SZ.exe to program the MCU FLASH module. In the
programming mode there is limited evaluation.
Ordinary amounts of static electricity from clothing or the work environment
can damage or degrade electronic devices and equipment. For example, the
electronic components installed on the printed circuit board are extremely
sensitive to electrostatic discharge (ESD). Wear a grounding wrist strap
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Quick Start Hardware Configuration Guide
53
Quick Start Hardware Configuration Guide
whenever handling any printed circuit board. This strap provides a conductive
path for safely discharging static electricity to ground.
B.1.1 KXICS Configurable Jumper Headers
Configure the seven jumper headers on the KXICS for your application
according to the tables in this section.
Table 4-2 KXICS Jumper Header Description
Jumper
Header
Type
(Factory
Default Shown
1
2
11
12
W1
Low Voltage
Select
W2
MCU Voltage
Select
W3
Target Clock
Enable
W4
PTB6 Select
3
1
3
1
1
3
Description
Used to set power for the MCU to match various target voltages.(No
default)
Jumper on position 1 & 2:
3.3 V
Jumper on position 3 & 4:
3.0 V
Jumper on position 5 & 6:
2.7 V
Jumper on position 7 & 8
2.2 V
Jumper on position 9 & 10
2.0 V
Jumper on position 11 & 12:
ADJ
Selects voltage powering MCU and related circuitry.
Jumper on position 1&2: Regulator Lo V as set by W1, is supplied by
MCU. Labeled LO V.
Jumper on position 3&2: Power supply, 5V Switched, is supplied by
board to MCU. Labeled 5V.
Jumper on position 1&2: supplies KXICS,9.8304 MHz, clock, to MCU
and target via W4.
Jumper on position 3&2: disables Xtal clock output, which will affect the
power-up reset. Labeled 0.
Jumper on position 1&2: MCU’s internal clock is supplied to target
cable via PTB6.
Jumper on position 3&2: KXICS Xtal clock is supplied to MCU.
User’s Manual
54
M68ICS08KX In-Circuit Simulator
Quick Start Hardware Configuration Guide
MOTOROLA
Quick Start Hardware Configuration Guide
Installing the Hardware
B.1.2 Target Interface Cable Connections
Below (Table 4-4) is a quick reference for defining the cable/connector setup to
use with the MC68HC908KX8
Table 4-3 Cable/Connector Options for MCUs
MCU
MC68HC908KX8
Flex Cable
Ribbon
Cable
MON08
Cable
J1
J5
J3
B.1.3 Host Computer — KXICS Interconnection (J6)
Connect the DE9 serial cable. Connect one end of this cable to your host PC and
the other end to connector J6 on the KXICS board.
B.2 Installing the Hardware
For installing Motorola development tools, the following steps provide
installation instructions for the KXICS hardware.
To prepare the KXICS (Figure 2-1) for use with a host PC:
1. Install an MCU (DIP or SOIC) into the KXICS board.
DIP-type MCU:
a. Place the pin tension arm of the KXICS DIP socket XU1 in the up
position.
b. Install the DIP type MCU into the DIP socket XU1. Be sure that the
pin 1 orientation of the silkscreened dot on the MCU aligns with the
pin 1 location on the DIP socket (upper left pin of the socket) .
c. Place the pin tension arm of the KXICS DIP socket XU1 in the
down position to secure the pins of the MCU to the socket.
NOTE:
The top (label side) of the MCU package must be visible when looking at the
component side of the board.
SOIC-type MCU:
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Quick Start Hardware Configuration Guide
55
Quick Start Hardware Configuration Guide
NOTE:
Installation of a SOIC type MCU requires the use of the SOIC-to-DIP adapter
identified in Table 1-1 of this manual.
a. Place the pin tension arm of the KXICS DIP socket XU1 in the up
position.
b. Install the SOIC-to-DIP adapter into the DIP socket XU1. Be sure
that the pin 1 orientation of the adapter aligns with the pin 1 location
on the DIP socket (upper left pin of the DIP socket).
CAUTION:
The SOIC-to-DIP adapter may be confusing to install. It must be placed into the
DIP socket, XU1, with the hinged side of the SOIC shell aligned at the bottom
of the KXICS board. This positioning will place the SOIC-type MCU socket pin
1 in the upper left corner of the SOIC socket.
c. Place the pin tension arm of the KXICS DIP socket XU1 in the
down position to secure the pins of the adapter to the socket.
d. Open the hinged access door on the SOIC shell.
e. Install the SOIC-type MCU into the SOIC socket of the adapter. Be
sure that the pin 1 orientation of the silkscreened dot on the MCU
aligns with the pin 1 location on the SOIC socket (upper left pin of
the socket).
f. Close and secure the hinged access door on the SOIC shell.
2. Connect the board to the host PC.
Locate the 9-pin connector labeled J6 on the board. Using the cable
provided, connect it to a serial COM port on the host PC.
3. Apply power to the board.
Connect the 5-volt power supply to the round connector on the board, J2.
Plug the power supply into an ac power outlet, using one of the
country-specific adapters provided. (The KXICS green power LED on
the board should light when switch SW1 is in the ON position.)
B.3 Installing the Software
For instructions for installing the ICS08 software, refer to P&E Microcomputer
Systems, Inc., M68ICS08KX In-Circuit Simulator Operator’s Manual.
User’s Manual
56
M68ICS08KX In-Circuit Simulator
Quick Start Hardware Configuration Guide
MOTOROLA
Quick Start Hardware Configuration Guide
Connecting to a Target System
B.4 Connecting to a Target System
The three ways to connect the M68ICS08KX simulator board to a target system
are via:
•
The flex cable
•
The ribbon cable
•
The MON08 cable
Connect the simulator board to the target system using one of these methods:
•
Using a flex cable
When emulating an MC68HC908KX MCU, connect the 16-pin
M68CLB05A flex cable (may be ordered) to the connectors labeled J1.
Attach the other end of the cable to the appropriate connector on the
target system. Target head adapters are available for the 16-pin SDIP,
16-pin DIP, and 16-pin SOIC versions of the MCU.
•
Using a ribbon cable
When emulating an MC68HC908KX MCU connect a 16-pin flat ribbon
cable to connector J5 on the simulator board. Attach the other end of the
cable to the appropriate connector on the target system.
•
Using a MON08 cable
Connect the MON08 debug interface cable to the MON08 debug
interface connector J3 for communication with the target system’s MCU.
The MON08 cable lets you program and debug the target system’s MCU
FLASH. An MCU must be installed in the target system, and there
should be no MCU installed in the KXICS.
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Quick Start Hardware Configuration Guide
57
Quick Start Hardware Configuration Guide
User’s Manual
58
M68ICS08KX In-Circuit Simulator
Quick Start Hardware Configuration Guide
MOTOROLA
User’s Manual — M68ICS08KX In-Circuit Simulator
Glossary
8-bit MCU — A microcontroller whose data is communicated over a data bus
made up of eight separate data conductors. Members of the
MC68HC908 Family of microcontrollers are 8-bit MCUs.
A — An abbreviation for the accumulator of the MC68HC908KX8 MCU.
accumulator — An 8-bit register of the MC68HC908KX8 CPU. The contents
of this register may be used as an operand of an arithmetic or logical
instruction.
assembler — A software program that translates source code mnemonics into
opcodes that can then be loaded into the memory of a microcontroller.
assembly language — Instruction mnemonics and assembler directives that
are meaningful to programmers and can be translated into an object
code program that a microcontroller understands. The CPU uses
opcodes and binary numbers to specify the operations that make up a
computer program. Humans use assembly language mnemonics to
represent instructions. Assembler directives provide additional
information such as the starting memory location for a program. Labels
are used to indicate an address or binary value.
ASCII — American Standard Code for Information Interchange. A widely
accepted correlation between alphabetic and numeric characters and
specific 7-bit binary numbers.
breakpoint — During debugging of a program, it is useful to run instructions
until the CPU gets to a specific place in the program, and then enter a
debugger program. A breakpoint is established at the desired address
by temporarily substituting a software interrupt (SWI) instruction for
the instruction at that address. In response to the SWI, control is passed
to a debugging program.
byte — A set of exactly eight binary bits.
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Glossary
59
Glossary
C — An abbreviation for carry/borrow in the condition codes register of the
MC68HC908KX8. When adding two unsigned 8-bit numbers, the C bit
is set if the result is greater than 255 ($FF).
CCR — An abbreviation for condition code register in the MC68HC908KX8.
The CCR has five bits (H, I, N, Z, and C) that can be used to control
conditional branch instructions. The values of the bits in the CCR are
determined by the results of previous operations. For example, after a
load accumulator (LDA) instruction, Z will be set if the loaded value
was $00.
clock — A square wave signal that is used to sequence events in a computer.
command set — The command set of a CPU is the set of all operations that
the CPU knows how to perform. One way to represent an instruction
set is with a set of shorthand mnemonics such as LDA meaning load A.
Another representation of an instruction set is the opcodes that are
recognized by the CPU.
condition codes register — The CCR has five bits (H, I, N, Z, and C) that can
be used to control conditional branch commands. The values of the bits
in the CCR are determined by the results of previous operations. For
example, after a load accumulator (LDA) instruction, Z will be set if
the loaded value was $00.
CPU — Central processor unit. The part of a computer that controls execution
of instructions.
CPU cycles — A CPU clock cycle is one period of the internal bus-rate clock.
Normally, this clock is derived by dividing a crystal oscillator source
by two or more so the high and low times will be equal. The length of
time required to execute an instruction is measured in CPU clock
cycles.
CPU registers — Memory locations that are wired directly into the CPU logic
instead of being part of the addressable memory map. The CPU always
has direct access to the information in these registers. The CPU
registers in an MC68HC908 are A (8-bit accumulator), X (8-bit index
register), CCR (condition code register containing the H, I, N, Z, and C
bits), SP (stack pointer), and PC (program counter).
User’s Manual
60
M68ICS08KX In-Circuit Simulator
Glossary
MOTOROLA
Glossary
cycles — See CPU cycles.
data bus — A set of conductors that are used to convey binary information
from a CPU to a memory location or from a memory location to a CPU;
in the MC68HC908KX8, the data bus is 8-bits.
development tools — Software or hardware devices used to develop computer
programs and application hardware. Examples of software
development tools include text editors, assemblers, debug monitors,
and simulators. Examples of hardware development tools include
simulators, logic analyzers, and PROM programmers. An in-circuit
simulator combines a software simulator with various hardware
interfaces.
EPROM — Erasable, programmable read-only memory. A non-volatile type
of memory that can be erased by exposure to an ultra-violet light
source. MCUs that have EPROM are easily recognized by their
packaging: a quartz window allows exposure to UV light. If an
EPROM MCU is packaged in an opaque plastic package, it is termed a
one-time-programmable OTP MCU, since there is no way to erase and
rewrite the EPROM.
EEPROM — Electrically erasable, programmable read-only memory.
H — Abbreviation for half-carry in the condition code register of the
MC68HC908KX8. This bit indicates a carry from the low-order four
bits of an 8-bit value to the high-order four bits. This status indicator is
used during BCD calculations.
I — Abbreviation for interrupt mask bit in the condition code register of the
MC68HC908KX8.
index register — An 8-bit CPU register in the MC68HC908KX8 that is used
in indexed addressing mode. The index register (X) also can be used as
a general-purpose 8-bit register in addition to the 8-bit accumulator.
input-output (I/O) — Interfaces between a computer system and the external
world. For example, a CPU reads an input to sense the level of an
external signal and writes to an output to change the level on an
external signal.
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Glossary
61
Glossary
instructions — Instructions are operations that a CPU can perform.
Instructions are expressed by programmers as assembly language
mnemonics. A CPU interprets an opcode and its associated operand(s)
as an instruction.
listing — A program listing shows the binary numbers that the CPU needs
alongside the assembly language statements that the programmer
wrote. The listing is generated by an assembler in the process of
translating assembly language source statements into the binary
information that the CPU needs.
LSB — Least significant bit.
MCU – Microcontroller unit — Microcontroller. A complete computer
system including CPU, memory, clock oscillator, and I/O on a single
integrated circuit.
MSB — Most significant bit.
N — Abbreviation for negative, a bit in the condition code register of the
MC68HC908KX8. In two’s-complement computer notation, positive
signed numbers have a 0 in their MSB (most significant bit) and
negative numbers have a 1 in their MSB. The N condition code bit
reflects the sign of the result of an operation. After a load accumulator
instruction, the N bit will be set if the MSB of the loaded value was a 1.
object code file — A text file containing numbers that represent the binary
opcodes and data of a computer program. An object code file can be
used to load binary information into a computer system. Motorola uses
the S-record file format for object code files.
operand — An input value to a logical or mathematical operation.
opcode — A binary code that instructs the CPU to do a specific operation in a
specific way. The MC68HC908KX8 CPU recognizes 210 unique 8-bit
opcodes that represent addressing mode variations of 62 basic
instructions.
OTPROM — A non-volatile type of memory that can be programmed but
cannot be erased. An OTPROM is an EPROM MCU that is packaged
in an opaque plastic package. It is called a one-time-programmable
User’s Manual
62
M68ICS08KX In-Circuit Simulator
Glossary
MOTOROLA
Glossary
MCU because there is no way to expose the EPROM to a UV light.
PC — Abbreviation for program counter CPU register of the
MC68HC908KX8.
program counter — The CPU register that holds the address of the next
instruction or operand that the CPU will use.
RAM — Random access memory. Any RAM location can be read or written
by the CPU. The contents of a RAM memory location remain valid
until the CPU writes a different value or until power is turned off.
registers — Memory locations that are wired directly into the CPU logic
instead of being part of the addressable memory map. The CPU always
has direct access to the information in these registers. The CPU
registers in the MC68HC908KX8 are A (8-bit accumulator), X (8-bit
index register), CCR (condition code register containing the H, I, N, Z,
and C bits), SP (stack pointer), and PC (program counter). Memory
locations that hold status and control information for on-chip
peripherals are called I/O and control registers.
reset — Reset is used to force a computer system to a known starting point and
to force on-chip peripherals to known starting conditions.
S record — A Motorola standard format used for object code files.
simulator — A computer program that copies the behavior of a real MCU.
source code — See source program.
SP — Abbreviation for stack pointer CPU register in the MC68HC908KX8
MCU.
source program — A text file containing instruction mnemonics, labels,
comments, and assembler directives. The source file is processed by an
assembler to produce a composite listing and an object file
representation of the program.
stack pointer — A CPU register that holds the address of the next available
storage location on the stack.
TTL — Transistor-to-transistor logic.
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Glossary
63
Glossary
VDD — The positive power supply to a microcontroller (typically 5 volts dc).
VSS — The 0-volt dc power supply return for a microcontroller.
Word — A group of binary bits. Some larger computers consider a set of
16 bits to be a word but this is not a universal standard.
X — Abbreviation for index register, a CPU register in the MC68HC908KX8.
Z — Abbreviation for zero, a bit in the condition code register of the
MC68HC908KX8. A compare instruction subtracts the contents of the
tested value from a register. If the values were equal, the result of this
subtraction would be 0 so the Z bit would be set; after a load
accumulator instruction, the Z bit will be set if the loaded value was
$00.
User’s Manual
64
M68ICS08KX In-Circuit Simulator
Glossary
MOTOROLA
Index
User’s Manual — M68ICS08KX In-Circuit Simulator
Index
A
ASCII
characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
B
Bill of Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Board layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
C
Cables
Flex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Serial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
checksum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Clock frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Clock selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Configuration
Standalone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Configuration options
Evaluation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 45
Jumper Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13, 46
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 45
Simulation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12, 45
Standalone options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Connectors
J1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16, 28
J2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 31
J3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 30, 37
J4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
J5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17, 29
J6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19, 32
MON08 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Index
65
Index
D
Debugging interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Delay Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
E
examples
S records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
H
Half-duplex mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
hardware
installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Headers
P1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
P2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
High voltage transients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Host
interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Host computer requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
I
ICS PWR LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Interface Connection Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Flex cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
MON08 cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Ribbon cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
J
J4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
K
KXICS
connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 5
User’s Manual
66
M68ICS08KX In-Circuit Simulator
Index
MOTOROLA
Index
Hardware components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Hardware operator’s manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
operation voltage range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
product components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
PWR LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
SOIC-to-DIP Socket Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
KXICS Software
components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
debugger/emulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
development package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
operator’s manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
simulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
L
LED
amber . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
ICS power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15, 49
Limitations
Bus Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Internal Clock Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Low Voltage Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Port A0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
M
MCU
internal clock. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
subsystem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
timing source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
memory
address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Microcontroller
DIP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Modes of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
MON08 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
MON08 connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Index
67
Index
P
Parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
DTR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
on/off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
R
record length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
record type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
RTS siganl. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
S
S records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39–44
Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Serial communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
serial port
connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Silk screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Software support programs
assembling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
debugging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
emulating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
programming. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
simulating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SOIC-to-DIP Socket Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
S-record
content. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
creating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
field contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
fields . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
S0 record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
S1 record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
S9 record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
termination record. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Start-Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
User’s Manual
68
M68ICS08KX In-Circuit Simulator
Index
MOTOROLA
Index
T
Target system
connecting to. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Test points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
V
VTST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Y
Y1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26, 27
M68ICS08KX In-Circuit Simulator
MOTOROLA
User’s Manual
Index
69
Index
User’s Manual
70
M68ICS08KX In-Circuit Simulator
Index
MOTOROLA
Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different
applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer’s technical experts.
Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems
intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a
situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold
Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of,
directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the
design or manufacture of the part. Motorola and
are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
How to reach us:
USA/EUROPE/Locations Not Listed: Motorola Literature Distribution, P.O. Box 5405, Denver, Colorado 80217. 1-303-675-2140
or 1-800-441-2447. Customer Focus Center, 1-800-521-6274
JAPAN: Motorola Japan Ltd.; SPS, Technical Information Center, 3-20-1, Minami-Azabu, Minato-ku, Tokyo 106-8573 Japan.
81-3-3440-8573
ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Silicon Harbour Centre, 2 Dai King Street, Tai Po Industrial Estate,
Tai Po, N.T., Hong Kong. 852-26668334
Mfax™, Motorola Fax Back System: [email protected]; http://sps.motorola.com/mfax/;
TOUCHTONE, 1-602-244-6609; US and Canada ONLY, 1-800-774-1848
HOME PAGE: http://motorola.com/sps/
Mfax is a trademark of Motorola, Inc.
© Motorola, Inc., 2000
M68ICS08KXUM/D