DATA SHEET ER1000~ER1004 SUPERFAST RECOVERY RECTIFIERS VOLTAGE 50 to 400 Volts CURRENT 10 Amperes TO-220AC Unit : inch (mm) FEATURES • Plastic package has Underwriters Laboratory Flammability Classification 94V-O. Flame Retardant Epoxy Molding Compound. .419(10.66) .196(5.00) .387(9.85) .163(4.16) .139(3.55) MIN • Exceeds environmental standards of MIL-S-19500/228 .054(1.39) • High surge capacity. • Super fast recovery times, high voltage. .624(15.87) • Low forwrd voltge, high current capability .548(13.93) .269(6.85) • Low power loss, high efficiency. .226(5.75) .045(1.15) • Both normal and Pb free product are available : .177(4.5)MAX Pb free: 98.5% Sn above .038(0.96) .019(0.50) MECHANICALDATA .50(12.7)MIN Normal : 80~95% Sn, 5~20% Pb .025(0.65)MAX Case: ITO-220AC Molded plastic Terminals: Lead solderable per MIL-STD-202, Method 208 .1(2.54) .1(2.54) Polarity: As marked. Standard packaging: Any Weight: 0.08 ounces, 2.24grams. MAXIMUM RATING AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% PA RA M E TE R S YM B O L E R1 0 0 0 E R1 0 0 1 E R1 0 0 1 A E R1 0 0 2 E R1 0 0 3 E R1 0 0 4 U N IT S M a xi m um R e c ur r e nt P e a k R e ve r s e V o l t a g e V RRM 50 100 150 200 300 400 V M a xi m um R M S V o l t a g e V RMS 35 70 105 140 210 280 V M a xi m um D C B l o c k i ng V o l t a g e V DC 50 100 150 200 300 400 V M a xi m um A ve r a g e F o r w a r d C ur r e nt . 3 7 5 " ( 9 . 5 m m ) l e a d l e n g t h a t Tc = 1 0 0 O C IAV 1 0 .0 A IF S M 150 A P e a k F o r w a r d S ur g e C ur r e nt , 8 . 3 m s s i ng l e ha l f s i ne - w a ve s up e r i m p o s e d o n r a t e d l o a d ( J E D E C m e t ho d ) M a xi m um F o r w a r d V o l t a g e a t 1 0 A , p e r e l e m e nt VF M a x i m u m D C R e v e r s e C u r r e n t a t TA = 2 5 O C R a t e d D C B l o c k i n g V o l t a g e TA = 1 0 0 O C IR M a x i m u m R e v e r s e R e c o v e r y Ti m e ( N o t e 2 ) T RR Ty p i c a l J u n c t i o n c a p a c i t a n c e ( N o t e 1 ) CJ 62 Rθ J C 3 .0 T J , T S TG - 5 0 TO + 1 5 0 M a xi m um The r m a l R e s i s t a nc e O p e r a t i n g J u n c t i o n a n d S t o r a g e Te m p e r a t u r e R a n g e 0 .9 5 1 .3 0 V 10 500 35 uA 50 ns pF O C / W O C NOTES: 1. Measured at 1 MHz and applied reverse voltage of 4.0 VDC. 2. Reverse Recovery Test Conditions: IF=.5A, IR=1A, Irr=.25A. 3. Both Bonding and Chip structure are available. STAD-AUG.24.2004 PAGE . 1 10 8 6 4 .375"9.5mm LEADLENGHTS RESISTIVEORINDUCTIVE LOAD 2 0 0 20 40 60 80 100 120 140 160 PEAK FORWARD SURGE CURRENT, AVERAGE FORWARD CURRENT, AMPERES RATING AND CHARACTERISTIC CURVES O 150 125 8.3ms Single Half Since-Wave JEDEC Method 100 75 50 25 0 1 2 CASE TEMPERAURE, C Fig.1- FORWARD CURRENT DERATING CURVE 10 10 10 10 10 2 O T J =125 C 1 0 -1 O T J =25 C 100 20 50-200V 10 8 6 4 300-400V 2 1.0 .8 .6 .4 T A =25 OC .1 -2 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE, % Fig.3- TYPICAL REVERSE CHARACTERISTIC STAD-AUG.24.2004 50 40 3 .2 10 20 Fig.2- MAXIMUM NON - REPETITIVE SURGE CURRENT FORWARD CURRENT, AMPERES REVERSE CURRENT, uA 10 5 NO. OF CYCLE AT 60HZ .6 .7 .8 .9 1.0 1.1 1.2 1.3 FORWARD VOLATGE, VOLTS Fig.4- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTIC PAGE . 2