PIC12C508A/509A Errata Sheet for PIC12C508A/509A (Rev. A Silicon) The PIC12C5XX-parts conform functionally to the PIC12C5XX Data Sheet (DS40139E), except for the anomalies described below: None Clarifications/Corrections to the Data Sheet: In the Device Data Sheet (DS40139E), the following clarifications and corrections should be noted. Section 13: Corrections for the DC Characteristics, Section 13.2, Section 13.3 and Section 13.4 are shown. Corrections for the GPIO pull-up resistor ranges are shown in Table 13-1. For the section titled “Reset”, additional information is provided on OSC1/CLKIN and OSC2/CLKOUT pin states during a MCLR. 2000 Microchip Technology Inc. DS80024B-page 1 PIC12C508A/509A 13.2 DC CHARACTERISTICS: PIC12LC508A/509A (Commercial, Industrial) PIC12LCE518/519 (Commercial, Industrial) PIC12LCR509A (Commercial, Industrial) Standard Operating Conditions (unless otherwise specified) Operating Temperature 0°C ≤ TA ≤ +70°C (commercial) –40°C ≤ TA ≤ +85°C (industrial) DC Characteristics Power Supply Pins Parm No. Characteristic Sym Min ∆IWDT – Typ(1) Max 2.0 2.0 4 5 Units µA µA Conditions VDD = 2.5V, Commercial VDD = 2.5V, Industrial * These parameters are characterized but not tested. Note 1: Data in the Typical (“Typ”) column is based on characterization results at 25°C. This data is for design guidance only and is not tested. 2: This is the limit to which VDD can be lowered in SLEEP mode without losing RAM data. 3: The supply current is mainly a function of the operating voltage and frequency. Other factors such as bus loading, oscillator type, bus rate, internal code execution pattern, and temperature also have an impact on the current consumption. a) The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail-to-rail; all I/O pins tristated, pulled to Vss, T0CKI = VDD, MCLR = VDD; WDT enabled/disabled as specified. b) For standby current measurements, the conditions are the same, except that the device is in SLEEP mode. 4: Does not include current through Rext. The current through the resistor can be estimated by the formula: IR = VDD/2Rext (mA) with Rext in kOhm. 5: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD or VSS. DS80024B-page 2 2000 Microchip Technology Inc. PIC12C508A/509A 13.3 DC CHARACTERISTICS: DC CHARACTERISTICS Param No. D040 D040A D070 Characteristic Input High Voltage I/O ports with TTL buffer GPIO weak pull-up current (Note 4) Input Leakage Current (Notes 2, 3) PIC12C508A/509A (Commercial, Industrial, Extended) PIC12CE518/519 (Commercial, Industrial, Extended) PIC12CR509A (Commercial, Industrial, Extended) Standard Operating Conditions (unless otherwise specified) Operating temperature 0°C ≤ TA ≤ +70°C (commercial) –40°C ≤ TA ≤ +85°C (industrial) –40°C ≤ TA ≤ +125°C (extended) Operating voltage VDD range as described in DC spec Section 13.1 and Section 13.2. Sym Min Typ† Max Units Conditions VIH IPUR 2.0V 0.25VDD + 0.8V 30 250 VDD VDD V V 4.5V ≤ VDD ≤ 5.5V otherwise 400 µA VDD = 5V, VPIN = VSS 250 +5 µA µA Vss ≤ VPIN ≤ VDD Vss ≤ VPIN ≤ VDD IIL D061 GP3/MCLR (Note 5) D061A GP3/MCLR (Note 6) 8 - 130 - † Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In EXTRC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC12C5XX be driven with external clock in RC mode. 2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as coming out of the pin. 4: Does not include GP3. For GP3 see parameters D0061 and D0061A. 5: This spec. applies to GP3/MCLR configured as external MCLR and GP3/MCLR configured as input with internal pull-up enabled. 6: This spec. applies when GP3/MCLR is configured as an input with pull-up disabled. The leakage current of the MCLR circuit is higher than the standard I/O logic. 2000 Microchip Technology Inc. DS80024B-page 3 PIC12C508A/509A 13.4 DC CHARACTERISTICS: DC CHARACTERISTICS Param No. D040 D040A Characteristic Input High Voltage I/O ports with TTL buffer D070 GPIO weak pull-up current (Note 4) Input Leakage Current (Notes 2, 3) D061 D061A GP3/MCLR (Note 5) GP3/MCLR (Note 6) PIC12LC508A/509A (Commercial, Industrial) PIC12LCE518/519 (Commercial, Industrial) PIC12LCR509A (Commercial, Industrial) Standard Operating Conditions (unless otherwise specified) Operating temperature 0°C ≤ TA ≤ +70°C (commercial) –40°C ≤ TA ≤ +85°C (industrial) Operating voltage VDD range as described in DC spec Section 13.1 and Section 13.2. Sym Min Typ† Max Units Conditions VIH IPUR 2.0V 0.25VDD + 0.8V 30 250 VDD VDD V V 4.5V ≤ VDD ≤ 5.5V otherwise 400 µA VDD = 5V, VPIN = VSS 250 +5 µA µA Vss ≤ VPIN ≤ VDD Vss ≤ VPIN ≤ VDD IIL † Note 1: 2: 3: 4: 5: 6: 8 - 130 - Data in “Typ” column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only and are not tested. In EXTRC oscillator configuration, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the PIC12C5XX be driven with external clock in RC mode. The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. Negative current is defined as coming out of the pin. Does not include GP3. For GP3 see parameters D0061 and D0061A. This spec. applies to GP3/MCLR configured as external MCLR and GP3/MCLR configured as input with internal pull-up enabled. This spec. applies when GP3/MCLR is configured as an input with pull-up disabled. The leakage current of the MCLR circuit is higher than the standard I/O logic. DS80024B-page 4 2000 Microchip Technology Inc. PIC12C508A/509A TABLE 13-1: VDD (Volts) PULL-UP RESISTOR RANGES* - PIC12C508A, PIC12C509A, PIC12CR509A, PIC12CE518, PIC12CE519, PIC12LC508A, PIC12LC509A, PIC12LCR509A, PIC12LCE518 and PIC12LCE519 Temperature (°C) Min Typ Max Units 42K 48K 49K 55K 17K 20K 22K 24K 63K 63K 63K 63K 20K 23K 25K 28K Ω Ω Ω Ω Ω Ω Ω Ω 80K 850K Ω 100K 110K 120K 60K 65K 80K 90K 1150K 1300K 1500K 600K 750K 900K 990K Ω Ω Ω Ω Ω Ω Ω GP0/GP1 2.5 5.5 –40 25 85 125 –40 25 85 125 38K 42K 42K 50K 15K 18K 19K 22K GP3(1) 2.5 –40 65K 25 80K 85 85K 125 100K 5.5 –40 50K 25 60K 85 65K 125 75K * These parameters are characterized but not tested. Note 1: The weak pull-up resistor and associated current for the GP3/MCLR pin is non-linear when the respective pin voltage is less than VDD - 1.0V. See parameter D061 for GP3/MCLR pin current specifications. Reset When MCLR is asserted, the state of the OSC1/CLKIN and CLKOUT/OSC2 pins are as follows: CLKIN/CLKOUT PIN STATES WHEN MCLR ASSERTED Oscillator Mode OSC1/CLKIN Pin OSC2/CLKOUT Pin EXTRC, CLKOUT OSC1 pin is on OSC2 tristated and driven by external circuit OSC2 pin is driven low EXTRC, OSC2 is I/O OSC1 pin is tristated and driven by external circuit OSC2 pin is tristate input INTRC, CLKOUT on OSC2 OSC1 pin is tristate input OSC2 pin is driven low INTRC, OSC2 is I/O OSC1 pin is tristate input OSC2 pin is tristate input 2000 Microchip Technology Inc. DS80024B-page 5 WORLDWIDE SALES AND SERVICE AMERICAS AMERICAS (continued) Corporate Office Toronto Singapore Microchip Technology Inc. 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-786-7200 Fax: 480-786-7277 Technical Support: 480-786-7627 Web Address: http://www.microchip.com Microchip Technology Inc. 5925 Airport Road, Suite 200 Mississauga, Ontario L4V 1W1, Canada Tel: 905-405-6279 Fax: 905-405-6253 Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore, 188980 Tel: 65-334-8870 Fax: 65-334-8850 Atlanta Microchip Technology, Beijing Unit 915, 6 Chaoyangmen Bei Dajie Dong Erhuan Road, Dongcheng District New China Hong Kong Manhattan Building Beijing, 100027, P.R.C. Tel: 86-10-85282100 Fax: 86-10-85282104 Microchip Technology Inc. 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307 Boston ASIA/PACIFIC China - Beijing ASIA/PACIFIC (continued) Taiwan Microchip Technology Taiwan 10F-1C 207 Tung Hua North Road Taipei, Taiwan Tel: 886-2-2717-7175 Fax: 886-2-2545-0139 EUROPE China - Shanghai Denmark Microchip Technology Unit B701, Far East International Plaza, No. 317, Xianxia Road Shanghai, 200051, P.R.C. Tel: 86-21-6275-5700 Fax: 86-21-6275-5060 Microchip Technology Denmark ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910 Hong Kong France Microchip Asia Pacific Unit 2101, Tower 2 Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2-401-1200 Fax: 852-2-401-3431 Arizona Microchip Technology SARL Parc d’Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 India Germany Microchip Technology Inc. Two Prestige Place, Suite 150 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175 Microchip Technology Inc. India Liaison Office No. 6, Legacy, Convent Road Bangalore, 560 025, India Tel: 91-80-229-0061 Fax: 91-80-229-0062 Arizona Microchip Technology GmbH Gustav-Heinemann-Ring 125 D-81739 München, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44 Detroit Japan Microchip Technology Inc. Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260 Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa, 222-0033, Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Arizona Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883 Microchip Technology Inc. 2 LAN Drive, Suite 120 Westford, MA 01886 Tel: 508-480-9990 Fax: 508-480-8575 Chicago Microchip Technology Inc. 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075 Dallas Microchip Technology Inc. 4570 Westgrove Drive, Suite 160 Addison, TX 75001 Tel: 972-818-7423 Fax: 972-818-2924 Dayton Los Angeles Microchip Technology Inc. 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338 New York Microchip Technology Inc. 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335 Korea Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea Tel: 82-2-554-7200 Fax: 82-2-558-5934 San Jose Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955 All rights reserved. © 2000 Microchip Technology Incorporated. Printed in the USA. 6/00 Italy United Kingdom Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5858 Fax: 44-118 921-5835 05/16/00 Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999. The Company’s quality system processes and procedures are QS-9000 compliant for its PICmicro® 8-bit MCUs, KEELOQ® code hopping devices, Serial EEPROMs and microperipheral products. In addition, Microchip’s quality system for the design and manufacture of development systems is ISO 9001 certified. Printed on recycled paper. Information contained in this publication regarding device applications and the like is intended through suggestion only and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip’s products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, except as maybe explicitly expressed herein, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies. DS80024B-page 6 2000 Microchip Technology Inc.