STMICROELECTRONICS 74LVC14A

74LVC14A
LOW VOLTAGE CMOS HEX INVERTER
HIGH PERFORMANCE
■
■
■
■
■
■
■
■
■
■
5V TOLERANT INPUTS
HIGH SPEED: tPD = 5.0ns (MAX.) at VCC = 3V
POWER DOWN PROTECTION ON INPUTS
AND OUTPUTS
SYMMETRICAL OUTPUT IMPEDANCE:
|IOH| = IOL = 24mA (MIN) at VCC = 3V
PCI BUS LEVELS GUARANTEED AT 24 mA
BALANCED PROPAGATION DELAYS:
tPLH ≅ tPHL
OPERATING VOLTAGE RANGE:
VCC(OPR) = 1.65V to 3.6V (1.2V Data
Retention)
PIN AND FUNCTION COMPATIBLE WITH
74 SERIES 00
LATCH-UP PERFORMANCE EXCEEDS
500mA (JESD 17)
ESD PERFORMANCE:
HBM > 2000V (MIL STD 883 method 3015);
MM > 200V
DESCRIPTION
The 74LVC14A is a low voltage CMOS HEX
SCHMITT INVERTER fabricated with sub-micron
silicon gate and double-layer metal wiring C2MOS
technology. It is ideal for 1.65 to 3.6 VCC
operations and low power and low noise
applications.
SOP
TSSOP
Table 1: Order Codes
PACKAGE
T&R
SOP
TSSOP
74LVC14AMTR
74LVC14ATTR
It can be interfaced to 5V signal environment for
inputs in mixed 3.3/5V system.
It has more speed performance at 3.3V than 5V
AC/ACT family, combined with a lower power
consumption.
Pin configuration and function are the same as
those of the 74LVC04A but the 74LVC14A has
hysteresis between the positive and negative
input threshold typically of 700mV.
All inputs and outputs are equipped with
protection circuits against static discharge, giving
them 2KV ESD immunity and transient excess
voltage.
Figure 1: Pin Connection And IEC Logic Symbols
July 2004
Rev. 7
1/12
74LVC14A
Figure 2: Input And Output Equivalent Circuit
Table 2: Pin Description
Table 3: Truth Table
PIN N°
SYMBOL
1,3,5,9,11,13
2, 4, 6, 8,
10, 12
7
1A to 6A
Data Inputs
1Y to 6Y
Data Outputs
GND
VCC
Ground (0V)
14
NAME AND FUNCTION
A
Y
L
H
H
L
Positive Supply Voltage
Table 4: Absolute Maximum Ratings
Symbol
Value
Unit
Supply Voltage
-0.5 to +7.0
V
VI
DC Input Voltage
-0.5 to +7.0
V
VO
DC Output Voltage (VCC = 0V)
VO
DC Output Voltage (High or Low State) (note 1)
IIK
VCC
Parameter
-0.5 to +7.0
V
-0.5 to VCC + 0.5
V
DC Input Diode Current
- 50
mA
IOK
DC Output Diode Current (note 2)
- 50
mA
IO
DC Output Current
ICC or IGND DC VCC or Ground Current per Supply Pin
Storage Temperature
Tstg
TL
Lead Temperature (10 sec)
± 50
mA
± 100
mA
-65 to +150
°C
300
°C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is
not implied
1) IO absolute maximum rating must be observed
2) VO < GND
2/12
74LVC14A
Table 5: Recommended Operating Conditions
Symbol
VCC
Parameter
Supply Voltage (note 1)
Value
Unit
1.65 to 3.6
V
VI
Input Voltage
0 to 5.5
V
VO
Output Voltage (VCC = 0V)
0 to 5.5
V
VO
Output Voltage (High or Low State)
0 to VCC
V
IOH, IOL
High or Low Level Output Current (VCC = 3.0 to 3.6V)
± 24
mA
IOH, IOL
High or Low Level Output Current (VCC = 2.7 to 3.0V)
± 12
mA
IOH, IOL
High or Low Level Output Current (VCC = 2.3 to 2.7V)
±8
mA
IOH, IOL
High or Low Level Output Current (VCC = 1.65 to 2.3V)
Top
dt/dv
Operating Temperature
Input Rise and Fall Time (note 2)
±4
mA
-55 to 125
°C
0 to 10
ns/V
1) Truth Table guaranteed: 1.2V to 3.6V
2) VIN from 0.8V to 2V at VCC = 3.0V
3/12
74LVC14A
Table 6: DC Specifications
Test Condition
Symbol
VT+
VT-
Parameter
Positive Input
threshold
Negative Input
threshold
VH
Hysteresis Voltage
VOH
High Level Output
Voltage
VOL
II
Ioff
ICC
∆ICC
Low Level Output
Voltage
-40 to 85 °C
VCC
(V)
-55 to 125 °C
Unit
Min.
Max.
Min.
Max.
1.4
2.0
2.0
2.2
1.0
1.4
1.5
1.8
1.1
1.1
1.2
1.2
0.6
0.8
0.8
0.8
0.3
0.4
0.6
0.8
0.3
0.3
0.3
0.3
VCC-0.2
1.4
2.0
2.0
2.2
1.0
1.4
1.5
1.8
1.1
1.1
1.2
1.2
IO=-100 µA
0.6
0.8
0.8
0.8
0.3
0.4
0.6
0.8
0.3
0.3
0.3
0.3
VCC-0.2
1.65
IO=-4 mA
1.2
1.2
2.3
IO=-8 mA
1.7
1.7
2.7
IO=-12 mA
2.2
2.2
3.0
IO=-12 mA
2.4
2.4
3.0
IO=-24 mA
2.2
2.2
1.65 to 3.6
IO=100 µA
0.2
0.2
1.65
IO=4 mA
0.45
0.45
2.3
IO=8 mA
0.7
0.7
2.7
IO=12 mA
0.4
0.4
3.0
IO=24 mA
0.55
0.55
3.6
VI = 0 to 5.5V
±5
±5
µA
0
VI or VO = 5.5V
10
10
µA
VI = VCC or GND
10
10
VI or VO = 3.6 to
5.5V
VIH = VCC-0.6V
± 10
± 10
500
500
1.65 to 1.95
2.3 to 2.7
3.0
3.6
1.65 to 1.95
2.3 to 2.7
3.0
3.6
1.65 to 1.95
2.3 to 2.7
3.0
3.6
1.65 to 3.6
Input Leakage
Current
Power Off Leakage
Current
Quiescent Supply
Current
ICC incr. per Input
Value
3.6
2.7 to 3.6
V
V
V
V
µA
µA
Table 7: Dynamic Switching Characteristics
Test Condition
Symbol
VOLP
VOLV
Parameter
Dynamic Low Level Quiet
Output (note 1)
TA = 25 °C
VCC
(V)
3.3
Value
Min.
CL = 50pF
VIL = 0V, VIH = 3.3V
Typ.
0.8
-0.8
Unit
Max.
V
1) Number of output defined as "n". Measured with "n-1" outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is
measured in the LOW state.
4/12
74LVC14A
Table 8: AC Electrical Characteristics
Test Condition
Symbol
tPLH tPHL
tOSLH
tOSHL
Parameter
Propagation Delay
Time
Output To Output
Skew Time (note1,
2)
Value
VCC
(V)
CL
(pF)
RL
(Ω)
ts = t r
(ns)
1.65 to 1.95
2.3 to 2.7
2.7
3.0 to 3.6
2.7 to 3.6
30
30
50
50
1000
500
500
500
2.0
2.0
2.5
2.5
-40 to 85 °C
Min.
1
Max.
10.5
7.0
6.0
5.0
1
-55 to 125 °C
Min.
1
Unit
Max.
14
9.1
7.5
6.4
1
ns
ns
1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = | tPLHm - tPLHn|, tOSHL = | tPHLm - tPHLn|
2) Parameter guaranteed by design
Table 9: Capacitive Characteristics
Test Condition
Symbol
Parameter
CIN
Input Capacitance
CPD
Power Dissipation Capacitance
(note 1)
TA = 25 °C
VCC
(V)
1.8
2.5
3.3
Value
Min.
fIN = 10MHz
Typ.
Unit
Max.
4
pF
37
38
42
pF
1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without
load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/n (per circuit)
5/12
74LVC14A
Figure 3: Test Circuit
RT = ZOUT of pulse generator (typically 50Ω)
Table 10: Test Circuit And Waveform Symbol Value
VCC
Symbol
1.65 to 1.95V
2.3 to 2.7V
3.0 to 3.6V
CL
30pF
30pF
50pF
50pF
RL
1000Ω
500Ω
500Ω
500Ω
VIH
VCC
VCC
2.7V
2.7V
VM
VCC/2
VCC/2
1.5V
1.5V
VOH
VCC
VCC
3.0V
3.0V
tr = tr
<2.0ns
<2.0ns
<2.5ns
<2.5ns
Figure 4: Waveform - Propagation Delay (f=1MHz; 50% duty cycle)
6/12
2.7V
74LVC14A
SO-14 MECHANICAL DATA
DIM.
mm.
MIN.
TYP
inch
MAX.
MIN.
TYP.
MAX.
A
1.35
1.75
0.053
0.069
A1
0.1
0.25
0.004
0.010
A2
1.10
1.65
0.043
0.065
B
0.33
0.51
0.013
0.020
C
0.19
0.25
0.007
0.010
D
8.55
8.75
0.337
0.344
E
3.8
4.0
0.150
0.157
e
1.27
0.050
H
5.8
6.2
0.228
0.244
h
0.25
0.50
0.010
0.020
L
0.4
1.27
0.016
0.050
k
0°
8°
0°
8°
ddd
0.100
0.004
0016019D
7/12
74LVC14A
TSSOP14 MECHANICAL DATA
mm.
inch
DIM.
MIN.
TYP
A
MAX.
MIN.
TYP.
MAX.
1.2
A1
0.05
A2
0.8
b
0.047
0.15
0.002
0.004
0.006
1.05
0.031
0.039
0.041
0.19
0.30
0.007
0.012
c
0.09
0.20
0.004
0.0089
D
4.9
5
5.1
0.193
0.197
0.201
E
6.2
6.4
6.6
0.244
0.252
0.260
E1
4.3
4.4
4.48
0.169
0.173
0.176
1
e
0.65 BSC
K
0˚
L
0.45
A
0.60
0.0256 BSC
8˚
0˚
0.75
0.018
8˚
0.024
0.030
A2
A1
b
e
K
c
L
E
D
E1
PIN 1 IDENTIFICATION
1
0080337D
8/12
74LVC14A
Tape & Reel SO-14 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
TYP
MAX.
MIN.
330
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
13.2
TYP.
0.504
22.4
0.519
0.882
Ao
6.4
6.6
0.252
0.260
Bo
9
9.2
0.354
0.362
Ko
2.1
2.3
0.082
0.090
Po
3.9
4.1
0.153
0.161
P
7.9
8.1
0.311
0.319
9/12
74LVC14A
Tape & Reel TSSOP14 MECHANICAL DATA
mm.
inch
DIM.
MIN.
A
MAX.
MIN.
330
13.2
TYP.
MAX.
12.992
C
12.8
D
20.2
0.795
N
60
2.362
T
10/12
TYP
0.504
22.4
0.519
0.882
Ao
6.7
6.9
0.264
0.272
Bo
5.3
5.5
0.209
0.217
Ko
1.6
1.8
0.063
0.071
Po
3.9
4.1
0.153
0.161
P
7.9
8.1
0.311
0.319
74LVC14A
Table 11: Revision History
Date
Revision
27-Jul-2004
7
Description of Changes
Ordering Codes Revision - pag. 1.
11/12
74LVC14A
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
The ST logo is a registered trademark of STMicroelectronics
All other names are the property of their respective owners
© 2004 STMicroelectronics - All Rights Reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
12/12