STMICROELECTRONICS LM235

LM135-LM235-LM335
Precision temperature sensors
Features
■
Directly calibrated in °K
■
1°C initial accuracy
■
Operates from 450µA to 5mA
■
Less than 1Ω dynamic impedance
TO-92
(Plastic package)
Description
The LM135, LM235, LM335 are precision
temperature sensors which can be easily
calibrated. They operate as a 2-terminal Zener
and the breakdown voltage is directly proportional
to the absolute temperature at 10mV/°K.
SO-8
(Plastic micropackage)
Pin connections
The circuit has a dynamic impedance of less than
1Ω and operates within a range of current from
450µA to 5mA without alteration of its
characteristics.
TO-92
(Bottom view)
Calibrated at +25°C, the LM135, LM235, and
LM335 have a typical error of less than 1°C over a
100°C temperature range. Unlike other sensors,
the LM135, LM235, LM335 have a linear output.
v-
v+
ADJ
SO-8
(Top view)
V+
8
1
NC
February 2008
Rev 3
NC
7
2
NC
NC
ADJ
3
4
6
NC
5
V-
1/16
www.st.com
16
Schematic diagram
1
LM135-LM235-LM335
Schematic diagram
Figure 1.
2
Schematic diagram
Absolute maximum ratings
Table 1.
Absolute maximum ratings (AMR)
Symbol
IR
IF
Parameter
Current
Reverse
Forward
Toper
Operating free-air temperature
range(1)
Continuous
Intermittent
Tstg
Storage temperature range
1. Tj ≤ 150°C
2/16
LM135
LM235
LM335LM335A
15
10
-55 to +150 -40 to +125 -40 to +100
+150 to +200 +125 to +150 +100 to +125
-65 to +150
Unit
mA
°C
°C
LM135-LM235-LM335
3
Temperature accuracy
Table 2.
Temperature accuracy
Parameter
Operating output voltage
Tcase = +25°C, IR = 1mA
Temperature accuracy
LM135 - LM235 LM335A
LM335
Unit
Min.
Typ.
Max.
Min.
Typ.
Max.
2.95
2.98
3.01
2.92
2.98
3.04
V
1
2
3
5
4
5
6
9
°C
0.5
1.5
1
2
Uncalibrated temperature error (IR = 1mA)
Tcase = +25°C
Tmin ≤ Tcase ≤ Tmax
Temperature error with 25°C calibration
Tmin ≤ Tcase ≤ Tmax., IR = 1mA
LM135 - LM235
LM335
LM335A
0.5
Calibrated error at extended temperature
Tcase = Tmax (intermittent)
°C
1
2
Non-linearity (IR = 1mA)
LM135 - LM235
LM335
LM335A
0.3
2
1
°C
0.3
0.3
4
Electrical characteristics
Table 3.
Electrical characteristics
°C
1.5
1.5
LM135 - LM235
LM335-LM335A
Parameter
Unit
Min.
Typ.
Max.
Operating output voltage change with current
450µA ≤ IR ≤ 5mA at constant temperature
2.5
10
Dynamic impedance (IR = 1mA)
0.5
0.6
Ω
Output voltage temperature drift
+10
+10
mV/°C
Time constant
Still air
Air 0.5m/s
Stirred oil
80
10
1
80
10
1
s
Time stability (Tcase = +125°C)
0.2
0.2
°C/kh
Note:
Min.
Typ.
Max.
3
14
mV
Accuracy measurements are made in a well-stirred oil bath. For other conditions, selfheating must be considered
3/16
Electrical characteristics
Reverse voltage change
Figure 3.
Temperature (°C)
Reverse current (mA)
Reverse characteristics
Figure 5.
Reverse voltage (V)
Dynamic impedance
Frequency (Hz)
4/16
Time (µs)
Figure 7.
Noise voltage
Noise (nV/√Hz)
Dynamic impedance (Ohm)
Figure 6.
Response time
Voltage swing (V)
Reverse current (mA)
Figure 4.
Calibrated error
Calibrated error (°C)
Reverse voltage change (mV)
Figure 2.
LM135-LM235-LM335
Frequency (Hz)
LM135-LM235-LM335
Thermal resistance junction to air
Figure 9.
Thermal time constant
Time constant (s)
Thermal resistance (°C/W)
Figure 8.
Electrical characteristics
Air velocity (m/s)
Air velocity (m/s)
Figure 11. Thermal response in stirred oil bath
Percent of final value (%)
Percent of final value (%)
Figure 10. Thermal response in still air
Time (min)
Time (s)
Forward voltage (V)
Figure 12. Forward characteristics
Forward current (mA)
5/16
Application information
5
LM135-LM235-LM335
Application information
There is an easy method of calibrating the device for higher accuracies (see Typical
applications).
The single point calibration works because the output of the LM135, LM235, LM335 is
proportional to the absolute temperature with the extrapolated output of sensor going to 0V
at 0°K (-273.15°C). Errors in output voltage versus temperature are only slope. Thus a
calibration of the slope at one temperature corrects errors at all temperatures.
The circuit output (calibrated or not) is given by the equation:
T
VOT + VOTO x ------
To
where T is the unknown temperature and To is the reference temperature (in °K).
Nominally, the output is calibrated at 10mV/°K.
Precautions should be taken to ensure good sensing accuracy. As in the case of all
temperatures sensors, self-heating can decrease accuracy. The LM135, LM235, and LM335
should operate with a low current but sufficient to drive the sensor and its calibration circuit
to their maximum operating temperature.
If the sensor is used in surroundings where the thermal resistance is constant, the errors
due to self-heating can be externally calibrated. This is possible if the circuit is biased with a
temperature stable current. Heating will then be proportional to Zener voltage and therefore
temperature. In this way, the error due to self-heating is proportional to the absolute
temperature as scale factor errors.
Typical applications
Figure 13. Basic temperature sensor
6/16
Figure 14. Wide operating supply
LM135-LM235-LM335
Figure 15. Calibrated sensor
Application information
Figure 16. Average temperature sensing
* Calibrated for 2.982V at 25°C
Figure 17. Isolated temperature sensor
7/16
Application information
Figure 18. Simple temperature controller
Figure 19. Centigrade thermometer
8/16
LM135-LM235-LM335
LM135-LM235-LM335
Application information
Figure 20. Differential temperature sensor
Figure 21. Thermocouple cold junction compensation (compensation for grounded
thermocouple)
9/16
Application information
Figure 22. Single power supply cold junction compensation
10/16
LM135-LM235-LM335
LM135-LM235-LM335
6
Package information
Package information
In order to meet environmental requirements, STMicroelectronics offers these devices in
ECOPACK® packages. These packages have a lead-free second level interconnect. The
category of second level interconnect is marked on the package and on the inner box label,
in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering
conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics
trademark. ECOPACK specifications are available at: www.st.com.
TO-92 tape & reel package information
Figure 23. TO-92 tape & reel package mechanical drawing
A1
P
T
P
A
H
W1
W2
W
L1
W0
H0
H
I1
d
H1
6.1
D0
F1 F2
P2
P0
11/16
Package information
Table 4.
LM135-LM235-LM335
TO-92 tape & reel package mechanical data
Millimeters
Inches
Dim.
Min.
Typ.
Min.
Typ.
Max.
AL
5.0
0.197
A
5.0
0.197
T
4.0
0.157
d
0.45
0.018
I1
2.5
P
11.7
12.7
13.7
0.461
0.500
0.539
PO
12.4
12.7
13
0.488
0.500
0.512
P2
5.95
6.35
6.75
0.234
0.250
0.266
F1/F2
2.4
2.5
2.8
0.094
0.098
0.110
Δh
-1
0
1
-0.039
0
0.039
ΔP
-1
0
1
-0.039
0
0.039
W
17.5
18.0
19.0
0.689
0.709
0.748
W0
5.7
6
6.3
0.224
0.236
0.248
W1
8.5
9
9.75
0.335
0.354
0.384
0.098
W2
0.5
0.020
H
20
0.787
H0
15.5
16
H1
DO
L1
12/16
Max.
16.5
0.610
0.630
25
3.8
4.0
4.2
11
0.650
0.984
0.150
0.157
0.165
0.433
LM135-LM235-LM335
6.2
Package information
TO-92 bulk package information
Figure 24. TO-92 bulk package mechanical drawing
Table 5.
TO-92 bulk package mechanical data
Millimeters
Inches
Dim.
Min.
L
Typ.
Max.
Min.
1.27
Typ.
Max.
0.05
B
3.2
3.7
4.2
0.126
0.1457
0.1654
O1
4.45
5.00
5.2
0.1752
0.1969
0.2047
C
4.58
5.03
5.33
0.1803
0.198
0.2098
K
12.7
O2
0.407
0.0197
0.02
a
0.35
0.5
0.5
0.508
0.016
0.0138
13/16
Package information
6.3
LM135-LM235-LM335
SO-8 package information
Figure 25. SO-8 package mechanical drawing
Table 6.
SO-8 package mechanical data
Dimensions
Ref.
Millimeters
Min.
Typ.
A
Max.
Min.
Typ.
1.75
0.25
Max.
0.069
A1
0.10
A2
1.25
b
0.28
0.48
0.011
0.019
c
0.17
0.23
0.007
0.010
D
4.80
4.90
5.00
0.189
0.193
0.197
H
5.80
6.00
6.20
0.228
0.236
0.244
E1
3.80
3.90
4.00
0.150
0.154
0.157
e
0.004
0.010
0.049
1.27
0.050
h
0.25
0.50
0.010
0.020
L
0.40
1.27
0.016
0.050
k
1°
8°
1°
8°
ccc
14/16
Inches
0.10
0.004
LM135-LM235-LM335
7
Ordering information
Ordering information
Table 7.
Order codes
Temperature
range
Package
Packing
Marking
LM135Z
-55°C to +150°C
TO-92
Bulk
LM135
LM235D
LM235DT
-40°C to +125°C
SO-8
Tube or
Tape & reel
LM235
LM235Z
-40°C to +125°C
TO-92
Bulk
LM235
SO-8
Tube or
Tape & reel
Order code
LM335D
LM335DT
LM335
-40°C to +100°C
LM335AD
LM335ADT
LM335A
LM335Z
-40°C to +100°C
LM335AZ
LM335AZT
8
TO-92
Bulk
LM335
Bulk or
Tape & reel
LM335A
Revision history
Table 8.
Document revision history
Date
Revision
6-May-2003
1
Initial release.
13-April-2004
2
Corrected error in pinout diagram for TO-92 package on cover page
(it is a bottom view, not a top view).
3
Updated Section 6: Package information and Table 7: Order codes.
Corrected typical values for uncalibrated temperature error in
Table 2.
Improved quality of electrical characteristics curves.
11-Feb-2007
Changes
15/16
LM135-LM235-LM335
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2008 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
16/16