M54HC139 RAD-HARD DUAL 2 TO 4 DECODER/DEMULTIPLEXER ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 13ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC = 4µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 54 SERIES 139 SPACE GRADE-1: ESA SCC QUALIFIED 50 krad QUALIFIED, 100 krad AVAILABLE ON REQUEST NO SEL UNDER HIGH LET HEAVY IONS IRRADIATION DEVICE FULLY COMPLIANT WITH SCC-9205-017 DESCRIPTION The M54HC139 is an high speed DUAL TWO LINE TO FOUR LINE DECODER/ DILC-16 FPC-16 ORDER CODES PACKAGE FM EM DILC FPC M54HC139D M54HC139K M54HC139D1 M54HC139K1 DEMULTIPLEXER fabricated with silicon gate C2MOS technology. The active low enable input can be used for gating or as a data input for demultiplexing applications. While the enable input is held high, all four outputs are high independently of the other inputs. All inputs are equipped with protection circuits against static discharge and transient excess voltage. PIN CONNECTION March 2004 1/8 M54HC139 IEC LOGIC SYMBOLS INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN N° SYMBOL 1, 15 2, 3 NAME AND FUNCTION 1G, 2G Enable Inputs 1A, 1B Address Inputs 1Y0 TO 1Y3 Outputs 4, 5, 6, 7 12, 11, 10, 9 2Y0 TO 2Y3 Outputs 14, 13 8 2A, 2B GND VCC 16 Address Inputs Ground (0V) Positive Supply Voltage TRUTH TABLE INPUTS OUTPUTS ENABLE SELECT LOGIC DIAGRAM This logic diagram has not be used to estimate propagation delays 2/8 Y0 Y1 Y2 Y3 SELECTED OUTPUT G B A H X X H H H H L L L L H H H NONE Y0 L L H H L H H Y1 L H L H H L H Y2 L H H H H H L Y3 M54HC139 ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Supply Voltage Value Unit -0.5 to +7 V -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 V DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA ± 50 mA VI DC Input Voltage VO DC Output Voltage IIK ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) V 300 mW -65 to +150 °C 265 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage VI Input Voltage VO Output Voltage Top Operating Temperature Input Rise and Fall Time tr, tf Value Unit 2 to 6 V 0 to VCC V 0 to VCC V -55 to 125 °C VCC = 2.0V 0 to 1000 ns VCC = 4.5V 0 to 500 ns VCC = 6.0V 0 to 400 ns 3/8 M54HC139 DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH VOL II ICC Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 4.5 6.0 2.0 4.5 6.0 Typ. Max. 1.5 3.15 4.2 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 3.15 4.2 0.5 1.35 1.8 Max. 1.5 3.15 4.2 0.5 1.35 1.8 V 0.5 1.35 1.8 2.0 IO=-20 µA 1.9 2.0 1.9 1.9 4.5 IO=-20 µA 4.4 4.5 4.4 4.4 Unit V 6.0 IO=-20 µA 5.9 6.0 5.9 5.9 4.5 IO=-4.0 mA 4.18 4.31 4.13 4.10 6.0 IO=-5.2 mA 5.68 2.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=20 µA 0.0 0.1 0.1 0.1 6.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=4.0 mA 0.17 0.26 0.33 0.40 6.0 IO=5.2 mA 0.18 0.26 0.33 0.40 6.0 VI = VCC or GND ± 0.1 ±1 ±1 µA 6.0 VI = VCC or GND 4 40 80 µA 5.8 5.63 V 5.60 V AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (A, B -Y) tPLH tPHL Propagation Delay Time (G -Y) 4/8 VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 Value TA = 25°C Min. Typ. Max. 30 8 7 45 15 13 39 13 11 75 15 13 130 26 22 110 22 19 -40 to 85°C -55 to 125°C Min. Min. Max. 95 19 16 165 33 28 140 28 24 Unit Max. 110 22 19 195 39 33 165 33 28 ns ns ns M54HC139 CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter VCC (V) Value TA = 25°C Min. Typ. Max. 10 CIN Input Capacitance 5.0 5 CPD Power Dissipation Capacitance (note 1) 5.0 46 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/2(per circuit) TEST CIRCUIT CL = 50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM: PROPAGATION DELAY TIMES (f=1MHz; 50% duty cycle) 5/8 M54HC139 DILC-16 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 2.1 2.71 0.083 0.107 a1 3.00 3.70 0.118 0.146 a2 0.63 1.14 0.025 B 1.82 2.39 0.072 b 0.40 0.45 0.50 0.016 0.018 0.020 b1 0.20 0.254 0.30 0.008 0.010 0.012 D 20.06 20.32 20.58 0.790 0.800 0.810 e 7.36 7.62 7.87 0.290 0.300 0.310 e1 0.88 2.54 0.035 0.045 0.094 0.100 e2 17.65 17.78 17.90 0.695 0.700 0.705 e3 7.62 7.87 8.12 0.300 0.310 0.320 F 7.29 7.49 7.70 0.287 0.295 0.303 I 3.83 0.151 K 10.90 12.1 0.429 0.476 L 1.14 1.5 0.045 0.059 0056437F 6/8 M54HC139 FPC-16 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 6.75 6.91 7.06 0.266 0.272 0.278 B 9.76 9.94 10.14 0.384 0.392 0.399 C 1.49 1.95 0.059 D 0.102 0.127 0.152 0.004 0.005 0.006 E 8.76 8.89 9.01 0.345 0.350 0.355 F 0.077 1.27 G 0.38 H 6.0 L 18.75 M 0.33 0.050 0.43 0.48 0.015 0.017 0.019 0.237 0.38 N 22.0 0.738 0.43 0.013 0.867 0.015 4.31 0.017 0.170 G F D H 9 16 A N L 8 1 H E B M C 0016030E 7/8 M54HC139 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 8/8