M74HC09 Quad 2-input and gate (open drain) Features ■ HIgh Speed: tPD = 7ns (Typ.) at VCC = 6V ■ Low power dissipation: ICC = 1µA (Max.) at TA = 25°C ■ High noise immunity: VNIH = VNIL = 28 % VCC (Min.) DIP-14 ■ Balanced propagation delays: tPLH ≅ tPHL ■ Wide operating voltage range: VCC (Opr) = 2V to 6V ■ Pin and function compatible with 74 series 09 SO-14 Description The M74HC09 is an high speed CMOS Quad 2input open drain and gate fabricated with silicon gate C2MOS technology. The internal circuit is composed of 3 stages including buffer output, which enables high noise immunity and stable output. All inputs are equipped with protection circuits against static discharge and transient excess voltage. Order codes Part number Package Packaging M74HC09B1R DIP-14 Tube M74HC09M1R SO-14 Tube M74HC09RM13TR SO-14 Tape and reel May 2006 Rev 2 1/13 www.st.com 13 Contents M74HC09 Contents 1 Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.1 Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3.1 Recommended operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 5 Test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 6 Waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 7 Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 8 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2/13 M74HC09 Pin settings 1 Pin settings 1.1 Pin connection Figure 1. 1.2 Pin connection (top through view) Pin description Table 1. Pin description Pin N° Symbol Name and function 1, 4, 9, 12 1A to 4A Data Inputs 2, 5, 10, 13 1B to 4B Data Inputs 3, 6, 8, 11 1Y to 4Y Data Outputs 7 GND Ground (0V) 14 VCC Positive Supply Voltage 3/13 Device summary 2 M74HC09 Device summary Figure 2. IInput and output equivalent circuit Figure 3. Logic diagram Table 2. Truth table Note: 4/13 A B Y L L L L H L H L L H H Z Z : High Impedance M74HC09 3 Maximum rating Maximum rating Stressing the device above the rating listed in the “Absolute Maximum Ratings” table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. Table 3. Absolute maximum ratings Symbol VCC Parameter Supply Voltage Value Unit -0.5 to +7 V VI DC Input Voltage -0.5 to VCC + 0.5 V VO DC Output Voltage -0.5 to VCC + 0.5 V IIK DC Input Diode Current ± 20 mA IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 25 mA DC VCC or Ground Current ± 50 mA 500(1) mW -65 to +150 °C 300 °C ICC or IGND PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) 1. 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C 3.1 Recommended operating conditions Table 4. Recommended operating conditions Symbol VCC Parameter Supply Voltage Value Unit 2 to 6 V VI Input Voltage 0 to VCC V VO Output Voltage 0 to VCC V Top Operating Temperature -55 to 125 °C VCC = 2.0V 0 to 1000 ns VCC = 4.5V 0 to 500 ns VCC = 6.0V 0 to 400 ns tr, tf Input Rise and Fall Time 5/13 Electrical characteristics 4 M74HC09 Electrical characteristics Table 5. DC specifications Test condition Symbol Parameter VIH VIL VOL 6/13 High Level Input Voltage Low Level Input Voltage Low Level Output Voltage Value TA = 25°C -40 to 85°C -55 to 125°C Unit VCC (V) Min Typ Max Min 2.0 1.5 1.5 1.5 4.5 3.15 3.15 3.15 6.0 4.2 4.2 4.2 Max Min Max V 2.0 0.5 0.5 0.5 4.5 1.35 1.35 1.35 6.0 1.8 1.8 1.8 2.0 IO = 20µA 0.0 0.1 0.1 0.1 4.5 IO = 20µA 0.0 0.1 0.1 0.1 6.0 IO = 20µA 0.0 0.1 0.1 0.1 4.5 IO = 4.0mA 0.17 0.26 0.33 0.40 6.0 IO = 5.2mA 0.18 0.26 0.33 0.40 V V II Input Leakage Current 6.0 VI = VCC or GND ± 0.1 ±1 ±1 µA IOZ Output Leakage Current 6.0 VI = VIH or VIL VO = VCC or GND ±0.5 ±5 ± 10 µA ICC Quiescent Supply Current 6.0 VI = VCC or GND 1 10 20 µA M74HC09 Electrical characteristics Table 6. AC electrical characteristics (CL = 50 pF, Input tr = tf = 6ns) Test Condition TA = 25°C Symbol Parameter VCC (V) tTHL tPLZ tPZL Output Transition Time Propagatio n Delay Time Propagatio n Delay Time Value Typ Max 2.0 30 75 95 110 4.5 8 15 19 22 6.0 7 13 16 19 10 75 95 110 4.5 8 15 19 22 6.0 7 13 16 19 20 75 95 110 4.5 8 15 19 22 6.0 7 13 16 19 2.0 2.0 Min -40 to 85°C -55 to 125°C Unit RL = 1 KΩ RL = 1 KΩ Min Max Min Max ns ns ns Table 7. Capacitive characteristics Test condition Symbol Parameter VCC (V) Value TA = 25°C Min Typ Max 10 -40 to 85°C -55 to 125°C Min Min Max Unit Max CIN Input Capacitance 5.0 5 COUT Output Capacitance 5.0 10 pF CPD Power Dissipation Capacitance (note 1) 5.0 6.5 pF 10 10 pF 7/13 Test circuit 5 M74HC09 Test circuit Figure 4. Note: Test circuit CL = 50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω) 6 Waveforms Figure 5. 8/13 Waveform - propagation delay (f = 1MHz; 50% duty cycle) M74HC09 7 Package mechanical data Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com 9/13 Package mechanical data M74HC09 Plastic DIP-14 MECHANICAL DATA mm. inch DIM. MIN. a1 0.51 B 1.39 TYP MAX. MIN. TYP. MAX. 0.020 1.65 0.055 0.065 b 0.5 0.020 b1 0.25 0.010 D 20 0.787 E 8.5 0.335 e 2.54 0.100 e3 15.24 0.600 F 7.1 0.280 I 5.1 0.201 L Z 3.3 1.27 0.130 2.54 0.050 0.100 P001A 10/13 M74HC09 Package mechanical data SO-14 MECHANICAL DATA DIM. mm. MIN. MAX. MIN. A 1.35 1.75 0.053 0.069 A1 0.1 0.25 0.004 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 8.55 8.75 0.337 0.344 E 3.8 4.0 0.150 0.157 e TYP inch 1.27 TYP. MAX. 0.050 H 5.8 6.2 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.4 1.27 0.016 0.050 k 0° 8° 0° 8° ddd 0.100 0.004 0016019D 11/13 Revision history 8 M74HC09 Revision history Table 8. Revision history 12/13 Date Revision Changes 07-Aug-2001 1 First Release 19-May-2006 2 New template, deleted TSSOP14 package information M74HC09 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 13/13