TS3021-3022 Rail-to-rail 1.8V high-speed comparator Features ■ Propagation delay: 33ns ■ Low current consumption: 64μA ■ Rail-to-rail inputs ■ Push-pull outputs ■ Supply operation from 1.8V to 5V ■ Wide temperature range: -40°C to +125°C ■ ESD tolerance: 2kV HBM / 200V MM ■ Latch-up immunity: 200mA ■ SMD packages TS3021 SOT23-5 / SC70-5 Pin connections (top view) 1 OUT Vcc- ■ Telecom ■ Instrumentation ■ Signal conditioning ■ High-speed sampling systems ■ Portable communication systems 2 + Applications Vcc+ 5 IN+ IN- 4 3 TS3022 SO8 / MiniSO8 Description The TS3021/2 single and dual comparators feature high-speed response time with rail-to-rail inputs. Specified from 2V to 5V supply voltage, these comparators can operate over a wide temperature range: -40°C to +125°C. Pin connections (top view) The TS3021/2 comparators offer micropower consumption as low as a few tens of microamperes thus providing an excellent ratio of power consumption current versus response time. Output 1 1 Inverting Input 1 2 _ Non Inverting Input 1 3 + VDD 4 8 VCC 7 Output 2 _ 6 Inverting Input 2 + 5 Non Inverting Input 2 The TS3021/2 include push-pull outputs and are available in small packages (SMD). February 2007 Rev 3 1/17 www.st.com 17 Contents TS3021-3022 Contents 1 Absolute maximum ratings and operating conditions . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 SOT23-5 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 SC70-5 (SOT323-5) package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . 13 SO8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 MiniSO8 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 5 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 2/17 TS3021-3022 1 Absolute maximum ratings and operating conditions Absolute maximum ratings and operating conditions Table 1. Absolute maximum ratings Symbol VCC Parameter Supply voltage(1) (2) Value Unit 5.5 V ±5 V V VID Differential input voltage VIN Input voltage range VDD-0.3 to VCC+0.3 PD Power dissipation(3) SC70-5 SOT23-5 SO8 MiniSO8 260 500 1000 650 Tstg Storage temperature -65 to +150 °C Tj Junction temperature 150 °C Lead temperature (soldering 10 seconds) 260 °C Human body model (HBM) 2000 Machine model (MM) 200 Latch-up immunity 200 TLEAD ESD(4) mW V mA 1. All voltage values, except differential voltage, are referenced to VDD. 2. The magnitude of input and output voltages must never exceed the supply rail ±0.3V. 3. Short-circuits can cause excessive heating and destructive dissipation. PD is calculated with Tamb=+25°C, Tj =+150°C and Rthja = 478°C/W for SC70-5, Rthja = 250°C/W for SOT23-5, Rthja = 125°C/W for SO8, Rthja = 190°C/W for MiniSO8. 4. ESD tolerances are compliant with MIL883C, JEDEC STANDARD JESD22, ANSI/ESD STM5.1-2001. Table 2. Operating conditions Symbol Parameter Tamb Ambient temperature VCC Supply voltage 0°C < Tamb < +125°C -40°C < Tamb < +125°C Vicm Common mode input voltage range -40°C < Tamb < +85°C +85°C < Tamb < +125°Tamb Rthja(1) Thermal resistance junction to ambient SC70-5 SOT23-5 SO8 MiniSO8 Value Unit -40 to +125 °C 1.8 to 5 2 to 5 V VDD-0.2 to VCC+0.2 VDD to VCC V 478 250 125 190 °C/W 1. For a 4-layer PCB. 3/17 Electrical characteristics TS3021-3022 2 Electrical characteristics Table 3. VCC=+2V, Tamb = +25°C, full Vicm range (unless otherwise specified)(1) Symbol Parameter VIO Input offset voltage ΔVIO Input offset voltage drift IIO Input offset current(2) IIB Input bias current(2) Test conditions -40°C < Tamb < +125°C -40°C < Tamb < +125°C -40°C < Tamb < +125°C -40°C < Tamb < +125°C Min. - No load, output low, Vicm=0V -40°C < Tamb < +125°C ICC Typ. Max. Unit 0.5 8 10 mV 3 20 μV/°C 1 20 100 nA 80 160 300 nA 75 105 115 64 90 125 μA - Supply current No load, output high, Vicm=0V -40°C < Tamb < +125°C ISC Short-circuit current Source Sink VOH Output voltage high Isource=1mA -40°C < Tamb < +125°C 1.88 1.80 VOL Output voltage low Isource=1mA -40°C < Tamb < +125°C - CMRR Common mode rejection ratio 0 < Vicm < 2V - 12 13 - mA - V 50 100 150 mV - 67 - dB 58 69 - dB 1.94 SVR Supply voltage rejection ΔVCC= 2 to 5V TPLH Propagation delay Low to high output level Vicm= 0V, f=10kHz, CL=50pF, Overdrive = 20mV Overdrive = 100mV - 39 33 75 60 ns TPHL Propagation delay High to low output level Vicm= 0V, f=10kHz, CL=50pF, Overdrive = 20mV Overdrive = 100mV - 39 33 75 60 ns TF Fall time f=10kHz, CL=50pF, RL=10kΩ, Overdrive = 100mV - - ns TR Rise time f=10kHz, CL=50pF, RL=10kΩ, Overdrive = 100mV - - ns 8 9 1. All values at non-ambient temperatures are guaranteed through correlation and simulation. No production test is performed at non-ambient temperatures. 2. Maximum values include unavoidable inaccuracies of the industrial test. 4/17 TS3021-3022 Table 4. Electrical characteristics VCC=+3.3V, Tamb = +25°C, full Vicm range (unless otherwise specified)(1) Symbol Parameter VIO Input offset voltage ΔVIO Input offset voltage drift IIO Input offset current(2) IIB Input bias current(2) Test conditions -40°C < Tamb < +125°C -40°C < Tamb < +125°C -40°C < Tamb < +125°C -40°C < Tamb < +125°C Min. - No load, output low, Vicm=0V -40°C < Tamb < +125°C ICC Max. Unit 0.5 8 10 mV 3 20 μV/°C 1 20 100 nA 80 160 300 nA 77 110 120 65 90 125 μA - Supply current No load, output high, Vicm=0V -40°C < Tamb < +125°C ISC Short circuit current Source Sink VOH Output voltage high Isource=1mA -40°C < Tamb < +125°C 3.20 3.10 VOL Output voltage low Isource=1mA -40°C < Tamb < +125°C - 0 < Vicm < 3.3V CMRR Common mode rejection ratio Typ. - 33 28 - mA - V 30 80 150 mV - 71 - dB 58 69 - dB 3.26 SVR Supply voltage rejection ΔVCC= 2 to 5V TPLH Propagation delay Low to high output level Vicm= 0V, f=10kHz, CL=50pF, Overdrive = 20mV Overdrive = 100mV - 42 34 85 65 ns TPHL Propagation delay High to low output level Vicm= 0V, f=10kHz, CL=50pF, Overdrive = 20mV Overdrive = 100mV - 41 34 80 65 ns TF Fall time f=10kHz, CL=50pF,RL=10kΩ, Overdrive = 100mV - - ns TR Rise time f=10kHz, CL=50pF,RL=10kΩ, Overdrive = 100mV - - ns 5 7 1. All values at non-ambient temperatures are guaranteed through correlation and simulation. No production test is performed at non-ambient temperatures. 2. Maximum values include unavoidable inaccuracies of the industrial test. 5/17 Electrical characteristics Table 5. TS3021-3022 VCC=+5V, Tamb = +25°C, full Vicm range (unless otherwise specified)(1) Symbol Parameter VIO Input offset voltage ΔVIO Input offset voltage drift IIO Input offset current(2) IIB Input bias current(2) Test conditions Typ. Max. Unit 0.5 8 10 mV 3 20 μV/°C 1 20 100 nA 80 160 300 nA 80 115 125 No load, output high, Vicm=0V -40°C < Tamb < +125°C 67 95 135 62 47 -40°C < Tamb < +125°C -40°C < Tamb < +125°C -40°C < Tamb < +125°C -40°C < Tamb < +125°C Min. - No load, output low, Vicm=0V -40°C < Tamb < +125°C ICC ISC Short circuit current Source Sink VOH Output voltage high Isource=4mA -40°C < Tamb < +125°C 4.80 4.70 VOL Output voltage low Isource=4mA -40°C < Tamb < +125°C - 0 < Vicm < 5V CMRR Common mode rejection ratio μA - Supply current - mA - V 110 180 250 mV - 72 - dB 58 69 - dB 4.87 SVR Supply voltage rejection ΔVCC= 2 to 5V TPLH Propagation delay Low to high output level Vicm= 0V, f=10kHz, CL=50pF, Overdrive = 20mV Overdrive = 100mV - 48 38 105 75 ns TPHL Propagation delay High to low output level Vicm= 0V, f=10kHz, CL=50pF, Overdrive = 20mV Overdrive = 100mV - 46 38 95 75 ns TF Fall time f=10kHz, CL=50pF,RL=10kΩ, Overdrive = 100mV - - ns TR Rise time f=10kHz, CL=50pF,RL=10kΩ, Overdrive = 100mV - - ns 4 4 1. All values at non-ambient temperatures are guaranteed through correlation and simulation. No production test is performed at non-ambient temperatures. 2. Maximum values include unavoidable inaccuracies of the industrial test. 6/17 TS3021-3022 Electrical characteristics Figure 1. Current consumption vs. power supply voltage Figure 2. Current consumption vs. power supply voltage Figure 3. Current consumption vs. power supply voltage Figure 4. Current consumption vs. power supply voltage Figure 5. Output voltage vs. source current VCC=2V Figure 6. Output voltage vs. sink current VCC=2V 7/17 Electrical characteristics TS3021-3022 Figure 7. Output voltage vs. source current VCC=3.3V Figure 8. Figure 9. Output Voltage vs. source current VCC=5V Figure 10. Output voltage vs. sink current VCC=5V Output voltage vs. sink current VCC=3.3V Figure 11. Input offset voltage vs. temperature Figure 12. Input bias current vs. temperature and common mode voltage and input voltage 8/17 TS3021-3022 Electrical characteristics Figure 13. Current consumption vs. commutation frequency Figure 14. Propagation delay vs. overdrive VCC=2V 800 VICM= 0V 700 600 VCC= 5V ICC (uA) 500 400 300 VCC= 3.3V VCC= 2V 200 100 0 10k 100k Frequency (Hz) 1M Figure 15. Propagation delay vs. overdrive VCC=2V Figure 16. Propagation delay vs. overdrive VCC=2V Figure 17. Propagation delay vs. overdrive VCC=3.3V Figure 18. Propagation delay vs. overdrive VCC=3.3V 9/17 Electrical characteristics TS3021-3022 Figure 19. Propagation delay vs. overdrive VCC=3.3V Figure 20. Propagation delay vs. overdrive VCC=5V Figure 21. Propagation delay vs. overdrive VCC=5V Figure 22. Propagation delay vs. overdrive VCC=5V Figure 23. Propagation delay vs. temperature VCC=5V, overdrive=100mV Figure 24. Propagation delay vs. common mode voltage, VCC=5V 10/17 TS3021-3022 3 Package information Package information In order to meet environmental requirements, STMicroelectronics offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an STMicroelectronics trademark. ECOPACK specifications are available at: www.st.com. 11/17 Package information 3.1 TS3021-3022 SOT23-5 package mechanical data Dimensions Ref. Millimeters Min. Max. Min. Typ. Max. A 0.90 1.45 35.4 57.1 A1 0.00 0.15 0.00 5.9 A2 0.90 1.30 35.4 51.2 b 0.35 0.50 13.7 19.7 C 0.09 0.20 3.5 7.8 D 2.80 3.00 110.2 118.1 E 2.60 3.00 102.3 118.1 E1 1.50 1.75 59.0 68.8 e 0.95 37.4 e1 1.9 74.8 L 12/17 Typ. Mils 0.35 0.55 13.7 21.6 TS3021-3022 3.2 Package information SC70-5 (SOT323-5) package mechanical data Dimensions Ref Millimeters Min Typ Mils Max Min Typ Max A 0.80 1.10 31.5 43.3 A1 0.00 0.10 0.0 3.9 A2 0.80 1.00 31.5 39.4 b 0.15 0.30 5.9 11.8 C 0.10 0.18 3.9 7.1 D 1.80 2.20 70.9 86.6 E 1.80 2.40 70.9 94.5 E1 1.15 1.35 45.3 53.1 e 0.65 25.6 e1 1.3 51.2 L 0.10 0.30 3.9 11.8 13/17 Package information 3.3 TS3021-3022 SO8 package mechanical data Dimensions Ref. Millimeters Min. Typ. Inches Max. Min. Max. A 1.35 1.75 0.053 0.069 A1 0.10 0.25 0.04 0.010 A2 1.10 1.65 0.043 0.065 B 0.33 0.51 0.013 0.020 C 0.19 0.25 0.007 0.010 D 4.80 5.00 0.189 0.197 E 3.80 4.00 0.150 0.157 e 1.27 0.050 H 5.80 6.20 0.228 0.244 h 0.25 0.50 0.010 0.020 L 0.40 1.27 0.016 0.050 k ddd 14/17 Typ. 8° (max.) 0.1 0.04 TS3021-3022 3.4 Package information MiniSO8 package mechanical data Dimensions Ref. Millimeters Min. Typ. A Inches Max. Min. Typ. 1.1 Max. 0.043 A1 0.05 0.10 0.15 0.002 0.004 0.006 A2 0.78 0.86 0.94 0.031 0.034 0.037 b 0.25 0.33 0.40 0.010 0.013 0.016 c 0.13 0.18 0.23 0.005 0.007 0.009 D 2.90 3.00 3.10 0.114 0.118 0.122 E 4.75 4.90 5.05 0.187 0.193 0.199 E1 2.90 3.00 3.10 0.114 0.118 0.122 e 0.65 K 0° L 0.40 L1 0.55 0.026 6° 0° 0.70 0.016 0.10 6° 0.022 0.028 0.004 15/17 Ordering information 4 TS3021-3022 Ordering information Table 6. Order codes Temperature range Part number Package Packaging Marking TS3021ILT SOT23-5 Tape & reel K520 TS3021ICT SC70-5 Tape & reel K52 SO8 Tube TS3022I TS3022IDT SO8 Tape & reel TS3022I TS3022IST MiniSO8 Tape & reel K521 -40°C, +125°C TS3022ID 5 16/17 Revision history Date Revision Changes 1-Jun-2006 1 Initial release. 1-Sep-2006 2 Dual version added. Pin-out of single TS3021 corrected. Modified temperature range for input common mode voltage. 22-Feb-2007 3 Addition of MiniSO8 package for dual version. TS3021-3022 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2007 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 17/17