MBS2 - MBS10 Single Phase 0.8 AMPS. Glass Passivated Bridge Rectifiers MBS .193(4.90) .177(4.50) .033(0.84) Features .022(0.56) .157(4.00) .142(3.60) UL Recognized File # E-96005 Ideal for printed circuit board Reliable low cost construction utilizing molded plastic technique High surge current capability High temperature soldering guaranteed: 260 oC / 10 seconds at 5 lbs., (2.3 kg ) tension Small size, simple installation Leads solderable per MIL-STD-202 Method 208 .272(6.9) MAX .102(2.60) .087(2.20) .106(2.70) .053(1.53) .014(0.35 .090(2.30) .037(0.95) .006(0.15 .008(0.20) .114(2.9) .043(1.10) .083(2.12) MAX MAX .028(0.70) .043(1.10) Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Symbol MBS2 VRRM 200 VRMS 140 VDC 200 Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current On glass-epoxy P.C.B. On aluminum substrate Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 0.4A MBS4 400 280 400 Typical Junction Capacitance Per Leg Typical Thermal Resistance Per Leg Operating Temperature Range Storage Temperature Range MBS8 MBS10 Units 800 1000 V 560 700 V 800 1000 V I(AV) 0.5 0.8 A IFSM 35 A VF 1.0 V 5.0 100 13 85 -55 to +150 -55 to +150 uA uA pF o C/W o C o C o Maximum DC Reverse Current @ TA=25 C at Rated DC Blocking Voltage @ TA=125 oC MBS6 600 420 600 IR Cj RθJA TJ TSTG Note: 1. Measured at 1.0MHz and Applied Reverse Voltage of 4.0 Volts D.C. - 646 - Version: B07 RATINGS AND CHARACTERISTIC CURVES (MBS2 THRU MBS10 ) FIG.1- DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.2- TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG INSTANTANEOUS REVERSE LEAKAGE CURRENT. (mA) AVERAGE FORWARD RECTIFIED CURRENT. (A) 0.8 Aluminum Substrate 0.7 0.6 0.5 Glass Epoxy P.C.B 0.4 0.3 0.2 Resistive or Inductive Load 0.1 0 0 40 20 80 120 60 100 O AMBIENT TEMPERATURE. ( C) 140 100 Tj=125 0C 10 1 0.1 Tj=25 0C 0.01 160 0 FIG.3-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 80 20 40 60 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 100 FIG.4- TYPICAL JUNCTION CAPACTITANCE PER LEG 30 35 JUNCTION CAPACITANCE (pF) PEAK FORWARD SURGE CURRENT. (A) O Tj=40 C Single Half Sine-Wave (JEDEC Method) 30 25 F=60 Hz F=50 Hz 20 15 Tj=25 C 25 f = 1 MHz Vsig = 50mVp-p 20 15 10 5 10 0 0.1 1 Cycle 5 1 10 REVERSE VOLTAGE. (V) 100 200 0 10 NUMBER OF CYCLES 1 100 FIG.5- TYPICAL FORWARD VOLTAGE CHARACTERISTICS PER LEG INSTANTANEOUS FORWARD CURRENT. (A) 10 1 Tj=25 0C 0.1 Tj=25 C Pulse Width=300ms 1% Duty Cycle 0.01 0.2 0.4 0.6 0.8 1.0 1.2 INSTANTANEOUS FORWARD VOLTAGE. (V) 1.4 Version: B07