P600A THRU P600M 6.0 AMPS Silicon Rectifiers Voltage Range 50 to 1000 Volts Current 6.0 Amperes P600 Features Plastic material used carries Underwriters Laboratory Classification 94V-0 High forward current capability High surge current capability High temperature soldering guaranteed: 260oC/10 seconds, 0.375”(9.5mm) lead length, 5lbs. (2.3kg) tension Mechanical Data Cases: Molded plastic Lead: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting position: Any Weight: 0.07 ounce, 2.1 grams Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Symbol P600A P600B P600D P600G P600J P600K P600M VRRM VRMS VDC 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 Units V V V Maximum Average Forward Rectified Current at o TA=60 C, 0.375”(9.5mm) Lead Length (Fig 1) TL=60℃, 0.125”(3.1mm) Lead Length (Fig 2) I(AV) 6.0 22.0 A Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) IFSM 400.0 A Maximum Instantaneous Forward Voltage @6.0A @100A VF Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=100℃ IR Typical Junction Capacitance ( Note 1 ) Typical Thermal Resistance (Note 2) Operating Junction and Storage Temperature Range 1.0 1.3 Cj RθJA RθJL 5.0 1.0 110 35 5.0 TJ, TSTG -50 to + 150 Notes: 1. Measured at 1 MHz and Applied Reverse Voltage of 4.0V D.C. 2. Mount on Cu-Pad Size 16mm x 16mm on P.C.B. - 524 - 1.4 V uA mA pF ℃/W ℃ RATINGS AND CHARACTERISTIC CURVES (P600A THRU P600M) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE 60 Hz RESISTIVE OR INDUCTIVE LOAD GROUND PLANE 1.0 X 1.0" (25.4 X 25.4mm) COPPER SURFACE AREA 5.0 4.0 0.050"(1.27mm) min. 3.0 ALTERNATE P.C.B. MOUNTING 1.1 x 1.0" (30 x 30mm) COPPER PADS 2.0 STANDARD P.C.B. MOUNTING 1.0 FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE 30 AVERAGE FORWARD CURRENT. (A) AVERAGE FORWARD RECTIFIED CURRENT. (A) 6.0 L=0.125" (3.18mm) 60 Hz RESISTIVE OR INDUCTIVE LOAD L=0.25" (6.35mm) 25 BOTH LEADS ATTACHED OF HEAT SINKS WITH LENGTH as SHOWN, L 20 15 L=0.375" (9.5mm) 10 L=0.625" (15.8mm) 5 0.375" (9.5mm) LEAD LENGTH 0 0 20 40 60 80 100 120 140 160 180 0 200 0 20 40 60 o AMBIENT TEMPERATURE. ( C) INSTANTANEOUS FORDWARD CURRENT AMPERES Tj=125 0C Tj=100 0C 1 Tj=25 0C 0.1 160 180 200 0.1 0 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0.6 0.8 1.0 1.2 1.4 1.6 FIG.6- TYPICAL TRANSIENT THERMAL IMPEDANCE 100 8.3 SINGLE HALF SINE-WAVE (JEDEC METHOD) 500 400 300 200 100 1 1 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG.5- MAXIMUM REPETITIVE FORWARD SURGE CURRENT 0.1 10 0.01 0.4 140 TRANSIENT THERMAL IMPEDANCE, OC/W INSTANTANEOUS REVERSE CURRENT MICROAMPERES 140 FIG.4- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10 0.01 0 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) PEAK FORWARD SURGE CURRENT AMPERES 120 100 100 0 100 o FIG.3- TYPICAL REVERSE CHARACTERISTICS 600 80 LEAD TEMPERATURE. ( C) 10 10.0 1 0.1 0.01 0.1 1 T, PULSE DURATION, sec. NUMBER OF CYCLES AT 60 Hz - 525 - 10 100