RGP10A THRU RGP10M 1.0 AMP. Glass Passivated Junction Fast Recovery Rectifiers Voltage Range 50 to 1000 Volts Current 1.0 Ampere DO-41 Features High temperature metallurgically bonded constructed Plastic material used carries Underwriters Laboratory Classification 94V-0 Glass passivated cavity-free junction Capable of meeting environmental standards of MIL-S-19500 1.0 ampere operation at TA=55oC with no thermal runaway Typical IR less than 0.1 uA High temperature soldering guaranteed: o 350 C / 10 seconds, 0.375”(9.5mm) lead length, 5 lbs., (2.3kg) tension Fast switching for high efficiency Mechanical Data Case: JEDEC DO-41 molded plastic over glass body Lead: Plated Axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting position: Any Weight: 0.012 ounce, 0.3 gram Dimensions in inches and (millimeters) Maximum Ratings and Electrical Characteristics Rating at 25℃ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% Symbol RGP RGP RGP RGP RGP RGP RGP Units Type Number Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current .375” (9.5mm) Lead Length @ TA = 55℃ Peak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) Maximum Instantaneous Forward Voltage @ 1.0A Maximum DC Reverse Current @ TA=25℃ at Rated DC Blocking Voltage @ TA=150℃ Maximum Reverse Recovery Time ( Note 1 ) TJ=25℃ Typical Junction Capacitance ( Note 2 ) Typical Thermal Resistance (Note 3) Operating Temperature Range VRRM VRMS VDC 10M 10A 10B 10D 10G 10J 10K 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 1000 560 700 800 1000 V V V I(AV) 1.0 A IFSM 30.0 A VF 1.3 V IR 5.0 200 uA uA 150 Trr Cj RθJA TJ 250 15 65 -65 to + 175 -65 to + 175 TSTG Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A Recover to 0.25A. 2. Measured at 1.0 MHz and Applied Reverse Voltage of 4.0 Volts. 3. Mount on Cu-Pad Size 5mm x 5mm on P.C.B. Storage Temperature Range - 574 - 500 nS pF ℃/W ℃ ℃ RATINGS AND CHARACTERISTIC CURVES (RGP10A THRU RGP10M) FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50W NONINDUCTIVE 10W NONINDUCTIVE trr +0.5A (-) DUT (+) 50Vdc (approx) (-) PULSE GENERATOR (NOTE 2) 1W NON INDUCTIVE OSCILLOSCOPE (NOTE 1) 0 -0.25A (+) -1.0A NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms 1cm 10 1.0 0.5 0.25 0.375" (9.5mm) LEAD LENGTH 0 50 75 100 125 150 175 o PEAK FORWARD SURGE CURRENT. (A) AMBIENT TEMPERATURE. ( C) FIG.3- MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 Tj=Tj max. 8.3ms Single Half Sine Wave JEDEC Method 20 INSTANTANEOUS FORWARD CURRENT. (A) 0.75 25 1 0.1 0 Tj=25 C PULSE WIDTH-300 S 1% DUTY CYCLE 0.01 0.4 0.6 0.8 1.0 1.2 FORWARD VOLTAGE. (V) 1.4 1.6 FIG.6- TYPICAL REVERSE CHARACTERISTICS 10 20 10 0 100 10 1 NUMBER OF CYCLES AT 60Hz FIG.4- TYPICAL JUNCTION CAPACITANCE 100 JUNCTION CAPACITANCE.(pF) FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS RESISTIVE OR INDUCTIVE LOAD Tj=25 0C 10 INSTANTANEOUS REVERSE CURRENT, MICROAMPERES AVERAGE FORWARD CURRENT. (A) FIG.2- MAXIMUM FORWARD CURRENT DERATING CURVE SET TIME BASE FOR 5/ 10ns/ cm Tj=125 0C 1 Tj=75 0C 0.01 0 1 10 100 REVERSE VOLTAGE. (V) - 575 - Tj=25 0C 0.1 0 20 40 60 80 100 120 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) 140