1260 COUPLED INDUCTORS High Reliability Coupled Inductors ML590PND The ML590PND series of shielded coupled inductors was designed specifically for high temperature applications – up to 155°C. The excellent coupling coefficient (k ≥ 0.98) makes it ideal for use in SEPIC applications. In SEPIC topologies, the required inductance for each winding in a coupled inductor is half the value needed for two separate inductors, allowing selection of a part with lower DCR and higher current handling. These inductors provide high inductance, high efficiency, excellent current handling and 500 V isolation in a very rugged part. They are well suited for use as VRM inductors in high-current DC-DC and VRM/VRD controllers. They can also be used as two single inductors connected in series or parallel, as a common mode choke or as a 1 : 1 transformer. D1 + L1 VIN + C1 L2 Q1 C2 + Load – VOUT – Typical SEPIC schematic Refer to Application Note, Document 639, “Selecting Coupled Inductors for SEPIC Applications” Dimensions are in Core material Ferrite Terminations Matte tin over nickel over phos bronze Weight: 2.8 – 3.2 g Ambient temperature –55°C to +105°C with Irms current, +105°C to +155°C with derated current Storage temperature Component: –55C to +155°C. Tape and reel packaging: –55°C to +80°C Winding to winding isolation 500 Vrms Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Winding-to-winding and winding-to-core isolation 500 Vrms Enhanced crush-resistant packaging 500/13″ reel; Plastic tape: 24 mm wide, 0.35 mm thick, 16 mm pocket spacing, 6.6 mm pocket depth inches mm ® Specifications subject to change without notice. Please check our website for latest information. 1102 Silver Lake Road Cary IL 60013 © Coilcraft, Inc. 2012 Document ML703-1 Revised 07/13/12 Phone 800-981-0363 Fax 847-639-1508 E-mail [email protected] Web www.coilcraft-cps.com 1260 COUPLED INDUCTORS ML590PND Series (1260) Irms (A) CouplingLeakage Isat (A)5 SRF (MHz)4 coefficient L typ 10% 20% 30% both one Inductance2 DCR max3 Part number1 (µH) (OhML) min typ typ (µH) drop drop drop windings6 winding7 ML590PND472MLZ 4.7±20% 0.036 30.0 38.0 0.98 0.20 9.00 10.18 11.08 3.16 4.47 ML590PND562MLZ 5.6 ±20%0.040 24.030.0 0.98 0.20 8.00 9.069.84 3.00 4.24 ML590PND682MLZ 6.8 ±20%0.048 22.027.0 0.98 0.24 7.00 8.008.64 2.75 3.88 ML590PND822MLZ 8.2 ±20%0.052 21.026.0 0.98 0.25 6.44 7.387.98 2.63 3.72 ML590PND103MLZ 10 ±20%0.060 18.022.0 0.99 0.26 5.40 6.326.88 2.45 3.46 ML590PND123MLZ ML590PND153MLZ ML590PND183MLZ ML590PND223MLZ ML590PND273MLZ 12 ±20%0.074 15 ±20%0.085 18 ±20%0.097 22 ±20%0.116 27 ±20%0.124 16.020.0 14.418.0 13.016.0 12.015.0 10.013.0 0.99 0.99 0.99 0.98 0.99 0.28 5.30 6.186.70 0.32 4.60 5.305.80 0.40 4.50 5.225.68 0.67 4.00 4.625.02 0.50 3.60 4.144.50 2.21 2.06 1.93 1.76 1.70 3.12 2.92 2.73 2.49 2.41 ML590PND333MLZ ML590PND393MLZ ML590PND473MLZ ML590PND563MLZ ML590PND683MLZ 33 ±20%0.134 10.012.4 0.99 39 ±20%0.142 9.612.0 0.99 47 ±20%0.174 9.311.6 0.99 56 ±20%0.198 8.410.5 0.99 68 ±20%0.216 8.010.0 >0.99 0.65 3.30 3.804.14 1.09 3.00 3.483.82 0.80 2.70 3.123.40 0.75 2.50 2.903.14 0.57 2.30 2.662.88 1.64 1.59 1.44 1.35 1.29 2.32 2.25 2.03 1.91 1.83 ML590PND823MLZ 82 ±20%0.274 ML590PND104MLZ100 ±20%0.322 ML590PND124KLZ120 ±10%0.418 ML590PND154KLZ150 ±10%0.476 ML590PND184KLZ180 ±10%0.536 6.9 6.2 5.5 5.1 4.9 8.6 7.8 6.8 6.4 6.1 0.99 0.99 0.99 0.99 0.99 1.522.102.402.60 1.411.902.182.38 1.341.601.842.04 1.521.501.761.92 1.801.401.641.78 1.15 1.06 0.93 0.87 0.82 1.62 1.50 1.31 1.23 1.16 ML590PND224KLZ220 ±10%0.691 ML590PND274KLZ270 ±10%0.806 ML590PND334KLZ330 ±10%1.09 ML590PND394KLZ 390±10% 1.20 ML590PND474KLZ 470±10% 1.59 4.4 3.4 3.2 2.9 2.4 5.5 4.3 4.0 3.6 3.0 >0.99 >0.99 >0.99 >0.99 >0.99 1.601.301.481.60 2.231.101.301.40 2.391.001.161.26 3.72 0.950 1.11 1.23 2.89 0.900 0.9941.09 0.72 0.67 0.57 0.55 0.48 1.02 0.95 0.81 0.77 0.67 ML590PND564KLZ 560±10% ML590PND684KLZ 680±10% ML590PND824KLZ 820±10% ML590PND105KLZ 1000±10% 2.2 2.1 2.0 1.9 2.8 2.6 2.5 2.4 >0.99 >0.99 >0.99 >0.99 2.55 5.76 2.86 4.32 0.45 0.42 0.37 0.34 0.63 0.59 0.52 0.49 1.81 2.06 2.65 3.06 0.800 0.9080.948 0.700 0.8040.874 0.640 0.7320.802 0.590 0.6740.728 Temperature rise calculation based on specified Irms 1. When ordering, please specify testing code: ML590PND105KLZ Testing:Z=COTS H = Screening per Coilcraft CP-SA-10001 N = Screening per Coilcraft CP-SA-10004 2. Inductance shown for each winding, measured at 100 kHz, 0.1 Vrms, 0 Adc on an Agilent/HP 4284A LCR meter or equivalent. When leads are connected in parallel, inductance is the same value. When leads are connected in series, inductance is four times the value. 3. DCR is for each winding. When leads are connected in parallel, DCR is half the value. When leads are connected in series, DCR is twice the value. 4. SRF measured using an Agilent/HP 4191A or equivalent. When leads are connected in parallel, SRF is the same value. 5. DC current, at which the inductance drops the specified amount from its value without current. It is the sum of the current flowing in both windings. 6. Equal current when applied to each winding simultaneously that causes a 40°C temperature rise from 25°C ambient. See temperature rise calculation. 7. Maximum current when applied to one winding that causes a 40°C temperature rise from 25°C ambient. See temperature rise calculation. 8. Electrical specifications at 25°C. Refer to Doc 639 “Selecting Coupled Inductors for SEPIC Applications.” Refer to Doc 362 “Soldering Surface Mount Components” before soldering. ® Specifications subject to change without notice. Please check our website for latest information. 1102 Silver Lake Road Cary IL 60013 © Coilcraft, Inc. 2012 Document ML703-1 Revised 07/13/12 Phone 800-981-0363 Fax 847-639-1508 E-mail [email protected] Web www.coilcraft-cps.com 1260 COUPLED INDUCTORS ML590PND Series (1260) Typical L vs Current Typical L vs Frequency 10000 10000 1000 µH 470 µH 100 µH 100 1000 µH 1000 Inductance (µH) Inductance (µH) 1000 47 µH 10 µH 10 470 µH 100 µH 100 47 µH 10 µH 10 4.7 µH 4.7 µH 1 0.1 1 10 100 Current (A) 1 0.01 0.1 1 10 Frequency (MHz) Current Derating 120 100 90 80 70 60 50 40 25°C Percent of rated Current 110 30 20 10 0 -55 -40 Isat Irms -20 0 20 40 60 80 100 120 140 160 Ambient temperature (°C) ® Specifications subject to change without notice. Please check our website for latest information. 1102 Silver Lake Road Cary IL 60013 © Coilcraft, Inc. 2012 Document ML703-1 Revised 07/13/12 Phone 800-981-0363 Fax 847-639-1508 E-mail [email protected] Web www.coilcraft-cps.com